all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manual | photos | label |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Installation Manual | Users Manual | 1.59 MiB | September 10 2019 | |||
1 |
|
Internal Photos | Internal Photos | 857.65 KiB | September 10 2019 | |||
1 |
|
External Photos | External Photos | 672.69 KiB | September 10 2019 | |||
1 |
|
Label | ID Label/Location Info | 175.63 KiB | September 10 2019 | |||
1 | Block Diagram | Block Diagram | October 09 2019 | confidential | ||||
1 |
|
FCC Confidentiality Request | Cover Letter(s) | 115.85 KiB | September 10 2019 | |||
1 | RF Exposure Info | September 10 2019 | ||||||
1 | Operational Description | Operational Description | October 09 2019 | confidential | ||||
1 |
|
Professional Installation Justification | Cover Letter(s) | 169.06 KiB | September 10 2019 | |||
1 | Schematics | Schematics | October 09 2019 | confidential | ||||
1 | Test Report | September 10 2019 | ||||||
1 | Test Setup Photos | September 10 2019 |
1 | Installation Manual | Users Manual | 1.59 MiB | September 10 2019 |
SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com SAFEMINE CAS INSTALLATION GUIDE Firmware V3.0 Version Control Date Version Author Description 21.10.2014 0.1 13.02.2015 0.2 24.02.2018 0.3 RGR RGR RGR Outline Corrections after review Included GPIO installation guide, GPIO logging functions, GPIO driving capacity, QM105 schematic and further corrections 1/39 Topic:
SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com This document is the reference manual for the installation, configuration and operation of SAFEmine units and tools. Document Nr:
DRA_CAS_QC2_150224 Date:
May 30, 2018 This document and the use of any information contained therein, is subject to the acceptance of the SAFEmine terms and conditions. They can be downloaded from www.SAFE-mine.com Disclaimer SAFEmine makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. SAFEmine reserves all rights to this document and the information contained herein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. Copyright 2012, SAFEmine. SAFEmine is a registered trademark SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 2/39 Table of Contents 1. Preface 5 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 1.1. Objective of this document .......................................................................... 5 1.2. Operation Safety Precautions ...................................................................... 5 1.3. Installation Safety Precautions .................................................................... 6 1.4. Legend of Symbols ....................................................................................... 6 2. Introduction ................................................................................................... 7 2.1. Purpose of the CAS system ......................................................................... 7 2.2. The Collision Avoidance Principle .............................................................. 7 2.3. Technology used ........................................................................................... 8 2.4. Limitations of the System ............................................................................. 8 3. Hardware Components ................................................................................. 9 3.1. Main Unit ........................................................................................................ 9 3.2. Displays ....................................................................................................... 11 3.3. Antennas ...................................................................................................... 12 3.4. Accessories ................................................................................................. 14 3.5. Connectors .................................................................................................. 16 3.6. Cables .......................................................................................................... 21 3.7. Network ........................................................................................................ 22 4. Hardware Installation Instructions............................................................. 23 4.1. General Rules and Best Practices ............................................................. 23 4.2. Main Unit ...................................................................................................... 24 4.3. Displays ....................................................................................................... 25 4.4. Antennas ...................................................................................................... 26 4.5. GPIO Connections....................................................................................... 34 Appendix A FCC compliance ......................................................................... 35 Appendix B RF radiation ................................................................................ 35 Appendix C IC compliance ............................................................................. 36 Appendix D Legal statement .......................................................................... 37 SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 3/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 4/39 1. Preface SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 1.1. Objective of this document This document is the main reference manual for the installation and configuration of SAFEmine CAS MainUnits and its associated accessories. It shall serve the technical personnel to correctly set up installations and enable them to maximize the SAFEmine CAS performance. 1.2. Operation Safety Precautions Operating any type of vehicle inside a mine at any time of the day is an inherently dangerous activity which is associated with considerable risks for crew, passengers, third parties, pedestrians, other vehicles and any object in its vicinity. In order to make full and safe use of SAFEmine QC200 series products, it is absolutely essential to be fully aware of the risks, operating conditions, restrictions and limitations associated with their use, including to ensure a proper installation and to perform regular software updates. This includes familiarity with and strict adherence to the Operating Manual and the Installation Manual. A vehicle equipped with the SAFEmine System must be operated in the same safe manner as if the SAFEmine System was not installed. The system is not a substitute for normal safe driving procedures and may never be relied upon. The SAFEmine System will provide no warning for some hazards, such as vehicles, obstacles, and other objects not equipped with properly operating SAFEmine devices. SAFEmine products are intended as an additional tool in determining potential traffic threats, supporting an alert and conscientious driver. SAFEmine products are never to be used in any application where failure of the products could result in personal injury or material damage. Before using, the latest versions of the respective manuals are to be consulted for familiarization with product operation and limitations. SAFEmine makes no warranties with respect to the product. In no event will SAFEmine Ltd be liable for lost use, profits, revenue, cost of procurement of substitute goods, or any damages. SAFEmine products may not be used in the USA and Canada unless the operator or customer has been authorized to do so in writing by SAFEmine Ltd. Customers agree to indemnify and hold harmless SAFEmine Ltd., its subsidiaries, and affiliates, and their respective successors and assigns, from and against all third party claims, loss, damage or expense, and any other liabilities whatsoever, which may be incurred by SAFEmine Ltd. with respect to any of the SAFEmine products. In addition, SAFEmine Ltd.'s current "General Terms and Conditions of Sale" apply. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 5/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 1.3. Installation Safety Precautions All work done to install the SAFEmine Collision Avoidance System shall be done in accordance with safe work standards and shall comply with the latest Health, Safety, and Reclamation Code for mines in the local jurisdiction. 1.4. Legend of Symbols Attention Symbol: Indicates a required actions and conditions. Information Symbol: Indicates best practices and recommendations. Document Symbol: Indicates a reference to an external document for in-depth information. Contact Symbol: Call SAFEmine Support for further assistance and information. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 6/39 2. Introduction SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 2.1. Purpose of the CAS system The main task for SAFEmine QC2xx series products is to support the operator while he scans the space ahead and around the vehicle with his own eyes, cameras and other aids. SAFEmine products are simple to use and are designed not to distract the operator from operating the vehicle. 2.2. The Collision Avoidance Principle The SAFEmine collision avoidance device is equipped with a GPS receiver, additional sensors and an RF transceiver. The GPS receiver will provide the unit with a position, speed and heading. This information is continuously broadcasted over the air thanks to the RF transmitter/ receiver. A vehicle will receive the information from all the surrounding vehicles while transmitting its own information. Based on this information, sophisticated SAFEmine algorithms will determine a collision risk level and indicate it to the operator of the vehicle via the display. As every vehicle has different dynamics and every mine has different rules, SAFEmine provides a list of features and configuration possibilities which can custom tailored to the needs of our customers. The display, either remote (QC230/QC24x/QC250) or integrated (QC235), warns the driver of potential threats, gives the status of the device, and allows user interaction with the Square button. Additionally to the LED indicators it also has a buzzer, a ambient light sensor and a noise sensor. The image above shows a display while the device is operating in a vehicle, traveling forward
(Reverse LED is OFF) and a vehicle (equipped with another SAFEmine device) is detected. The led on in the 12 oclock position indicates the presence of a vehicle in front. Several colors and sounds indicate different threat levels. Depending on the distance to other vehicles and on the configuration parameters an alarm might be audible. The center compass displays direction and distance of vehicles within the RF transmitter / receiver range but it also serves to display error codes in the case a system failure was detected. The LEDs on the left side of the display show the status of the SAFEmine device. They indicate if the device has enough power, has acceptable GPS reception or is traveling backwards as well as other information about the system. Depending on the configuration, pushing the square button on the right of the display can trigger three functions:
1) Flag special events in the units log-file: for example an incident or a situation where the user believes the SAFEmine device didnt perform as expected. 2) Announce the ID of nearby vehicles: If the Voice Option is enabled, surrounding vehicles are announced. 3) Acknowledge an alarm: The operator can stop the warning sound for example when being towed by another vehicle. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 7/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com Pressing the button for 3 seconds or longer seconds will restart the SAFEmine unit. All alarms are indicated during a minimum of 1.5 seconds to allow the operator to see and react to it. The alarm will stop once the threat is gone or if one of the two vehicles stops. For further information regarding the collision avoidance and proximity awareness offered by the SAFEmine system please contact your support responsible or write to support@safe-mine.com requesting the operator training. 2.3. Technology used The SAFEmine system based on technology widely used in aviation consists of a main unit, an operator's interface (both output and input) and a dual antenna (one for GPS, one for radio communication). Depending on the product selected, the operator's interface is either integrated into the main unit or mounted as a separate display unit. The main unit contains all main sensors (GPS engine, radio transceiver, micro-controller, memory, data interfaces and a series of sensors), The operator the beeper/loudspeaker for acoustical warnings and one button for input. interface provides both a directional display of nearby traffic and danger, SAFEmine QC200 series products receive position and movement information from an internal high-
sensitivity 50 channel GPS receiver with an external antenna. Additional sensors and logic further enhance the accuracy of position measurements. The predicted driving path of the vehicle, in which a SAFEmine QC200 series product is installed, is calculated by the main unit and the obtained information is transmitted by radio as a low power digital burst signal at frequent intervals. Provided they are within receiving range, these signals are received by other vehicles also equipped with SAFEmine QC200 series products. The incoming signal is compared with the driving path calculated and predicted for the second vehicle, taking into account configuration parameters like maximum acceleration or vehicle dimension. At the same time, SAFEmine QC200 series products optionally compare the predicted driving path with known static obstacle data, e.g. electric power lines. If a SAFEmine QC200 series product determines the risk of dangerous proximity to another vehicle or to an obstacle equipped with a SAFEmine QC200 series product, the unit gives the operator a warning of the greatest danger at that moment. This warning is given by a buzzing sound (beep) and bright light emitting diodes (LED). The display also gives indication of the threat level, plus the horizontal bearing to the threat. The operating range is very dependent upon the antenna installation in or outside the vehicle. The normal range is about 500m for line-of-sight operations, but up to 2 km may be achieved in individual cases. For their radio communication, SAFEmine QC200 series products use a proprietary patent- and copyright-protected protocol. Any non-licensed use, dissemination, copying, implementation or reverse engineering of the SAFEmine QC200 series radio communication protocol, their hardware and software or parts of it is forbidden by law and will be prosecuted. SAFEmine is a registered trademark and may not be used without license. 2.4. Limitations of the System SAFEmine is not designed for use in deep or narrow open pit mines where availability of GPS satellites is not sufficient in any other application than open pit mining on vehicles with excessive vibration SAFEmine units are only to be used with other SAFEmine units, otherwise inconsistent function may occur. SAFEmine Ltd. cannot assume any liability from correct or incorrect use of above specified products other than regular warranty according to SAFEmine Ltd. General Terms and Conditions. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 8/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 3. Hardware Components 3.1. Main Unit 3.1.1. Overview The main unit houses the GPS receiver, RF transceiver, processor, interface logic and additional sensors. The housing is made of aluminum with plastic end-bezels. All connectors are on the backside of the unit. The main unit is produced in six different models: QC230, QC235, QC220, QC24x, QC250 and QN555. All units, with the exception of the QN555, are enclosed in a black anodized aluminum casing in order to minimize glare. The QN555 has a plastic, watertight enclosure for outdoor operation. QC230 QC235 QC2201 QC24x QC250 QN555 CAS GSM/LTE/UMTS/
LTE WiFi Integrated display Digital IOs Digital Inputs Analog Inputs 12 12 4 2 2 4 2 2 1 Always delivered with speaker and voice option. 2 Early versions had limited IO functionality. Please consult chapter 3.4 for specific information 3.1.2. QC230 & QC235 4 2 2 The QC230 and QC235 models represent the basic line of SAFEmine CAS units. The QC230 is meant to be installed with an external display while the QC235 unit offers a built-in display but can also be upgraded with an external display. Installation of these units can be realized with a minimal amount of effort. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 9/39 3.1.3. QC220 & QC24x SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com The QC24x and QC220 models provide networking capability through GSM/LTE connectivity and are meant to be operated with and external display. This is in addition to the functionality offered by the QC230 and QC230. This enables the support of online vehicle tracking. To enable this feature, a SIM card with an activated data plan must be placed in the SIM card slot of the SAFEmine unit and the corresponding parameters need to be configured. Further information on vehicle tracking is provided in chapter 3.5. 3.1.4. QC250 The QC250 model provides network connectivity through WiFi and is meant to be installed with an external display. The QC250 model supports vehicle tracking via WiFi. In order to provide this functionality the QC250 unit requires to be configured with the WiFi network specific parameters. Further information on tracking is provided in chapter 3.7 and Error! Reference source not found.. 3.1.5. QN555 The QN555 is a roof top magnetic mount, self-powered and self-contained CAS device which offers ease and speed of installation on the roof of e.g. a temporary installation on a light vehicle. It is a solution for contractors and temporary visitors in surface mines where all mine vehicles require having SAFEmine installed. Detailed information regarding the QN555 QuickMount unit can be found in the QN555 user guide. QN555 requires an external display but no additional antenna is required. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 10/39 3.2. Displays SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 3.2.1. Overview An external display is required for all Main Units to work correctly. The only exceptions are the QC235 and the QC220 units. The QC235 have an inbuilt display and thus do not necessarily require an additional external display. The QC220 main application is vehicle tracking which does not require anti-collision and can work without the indication of nearby SAFEmine CAS systems. All other SAFEmine CAS systems require a display in order to be fully operational. The display not only indicates the proximity and direction of other SAFEmine CAS systems but also issues audible warnings, indicates system errors and malfunctions and provides an interface for interaction. 3.2.2. QD200 RemoteDisplay The QD200 remote display unit can be connected to all QC2xx units. The QC230 and QC235 units only require a QD221 (1.5m) or QD222 (5m) display cable extension. To connect to QC220, QC24x or QC250 units an additional QM106 display Y-cable is required. The QD200 Interface offers the following attributes:
Indication of surrounding vehicles through 12 dual color LEDs (red/green) in a circle Status Indication through 4 dual color LEDs (red/green): Power, GPS, Reverse and Mode Multifunction push-button Piezoelectric buzzer Ambient light sensor The maximum length of the display cable is 15m. This can be achieved be connecting several display extension cables together. The LED brightness is automatically controlled based on ambient light, in order to provide dimming for night operation. The buzzer, with a maximum volume of 85dB (at 10cm distance), can be automatically controlled based on ambient noise. 3.2.3. QD204 ScopeScreen The ScopeScreen provides a 4 graphical display showing a bird-view map of the vehicles surroundings. Its main use lies in rotational vehicles and stockpile applications which require detailed information on the QD204 ScopeScreen to be installed with the QM105 Power Saving Display Cable connected to ignition, in order to preserve the vehicle battery from draining. Its installation is compulsory for light vehicles. their environment. However SAFEmine strongly recommends The QD204 further provides 2 USB connectors for FW upgrades and log-files extraction. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 11/39 3.3. Antennas SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 3.3.1. Overview The antennas provided by SAFEmine are customized and combined GPS and RF antennas especially designed for the harsh environments of mines. Only antennas supplied by SAFEmine may be attached to the antenna connectors The following matrix shows the antennas main attributes:
Antenna QF012 QF020 QF024 QF026 QF028 QF034 QF036 QF037 QF038 Through hole mount Magnetic mount Adhesive
(in-cabin) Braket mount GPS RF GSM/LTE WiFi LongRange WiFiRF 3.3.2. Antenna Selector Please refer to the following matrix to select the correct antenna corresponding to your CAS main unit:
QC Model: QF012 QF020 QF024 QF026 QF028 QF034 QF036 QF037 QF038 QC230 QC235 QC220 QC24x QC250 The following matrix indicates the pairing of CAS units and antennas for specific applications:
Application: QF012 QF020 QF024 QF026 QF028 QF034 QF036 QF037 QF038 CAS only QC23x CAS and TRACK QC24x QC250 QC23x QC24x QC250 TRACK only QC220 QC220 QC220 QC24x QC250 QC250 QC250 SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 12/39 3.3.3. Through Hole Antennas SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com SAFEmine recommends the installation of through whole antennas (QF012 GPS/RF, QF020 GPS/GSM and QF036 GPS/RF/WiFi) for all permanent installation for its superior stability even in heavy vibration. This type of antenna is equipped with a threaded tube at the bottom to secure its position. The antenna is equipped with 15cm pigtail of coaxial cable with 50 wave impedance. Short cable pigtails on antennas have the advantage to be able to replace either the antenna or the extension cable in case either is being damaged. Furthermore, testing of the cable and antenna independently with an SWR-meter is strongly recommended (please contact SAFEmine for SWR-meter recommendations). 3.3.4. Magnetic Mount Antennas The magnetic mount antennas (QF024 GPS/RF, QF026 GPS/GSM and QF037 GPS/RF/WiFi) are equipped with a 3.5m pigtail of coaxial cable with 50 wave impedance. Its magnetic base attaches to any reasonably magnetic material. It allows an easy installation on vehicle roof tops and is ideal for light or other vehicles with moderate vibration. 3.3.5. Adhesive Antennas These antennas (QF028 GPS/GSM/LTE and QF034 GSM/LTE) are installed on the inside of the windshields. They are not waterproof and thus require to be installed in a dry environment. 3.3.6. Bracket Mount Antennas The bracket mount antennas (QF038 WiFi) are designed to be mounted on handrails and similar structures. Their main field of application is extending the range of WiFi communication. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 13/39 3.4. Accessories SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 3.4.1. Overview Several accessories are available to extend the SAFEmine CAS system functionality. All accessories, with exception of the QR310 TrackingRadars, can be easily installed on existing basic SAFEmine CAS Systems and extended further when needed. As regarding the TrackingRadars, specific training of your technical staff is required. All accessories require FW upgrades for activation. The QL015 Loudspeaker requires additional SW to be installed (voice file). If you consider upgrading your CAS system with any of our accessories, please contact your local SAFEmine support responsible for further guidance. For the different accessories available, please consult the corresponding documentation for configuration and use the correct cables for connection:
Documentation Y-Cable Extension Cables Other Loudspeaker QL015 SM Voice Application Note DriverID Reader QL460 SM KeyControl Application Note QM108 Not needed QM106 QD221 (1.5m) KeyCards SerialExtender QS430 SM SerialExtender Application Note QM103 or QS422 QD221 (1.5m) TrackingRadar QR310 SM TrackingRadar Installation Manual QS413 QR321 (2m) QR322 (5m) QR323 (10m) QR324 (20m) QR320 (CAN Y) QR421 (Terminator) Panic Button QP137 Panic Button Application Note Not needed
(GPIO) Not Needed 3.4.2. QL015 Loudspeaker plus Voice Option In order to install the SAFEmine Voice option, the CAS system requires the installation of the QL015 loudspeaker for audible output. The loudspeaker enables the CAS to voice different messages regarding vehicles ahead, collision warnings, tailgating, over-speed and many more. For in-depth information on SAFEmine Voice configuration and the installation of QL015 loudspeakers please consult the voice application note. For further information please contact support@safe-mine.com SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 14/39 3.4.3. QL460 DriverID Reader SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com The QL460 DriverID Reader enables the CAS system to verify the authorization of the operator through contactless RF-ID cards. The installation of QL460 DriverID Reader requires a QS430 SerialExtender. For in-depth information on SAFEmine DriverID configuration and the installation of QL460 keycard -
reader please consult with your support responsible or contact support@safe-mine.com. Please refer to the Key-Control Application Note for further information. 3.4.4. QS430 SerialExtender The QS430 SerialExtender adds 3 additional ports serial ports to the CAS unit. Several serial devices such as QD200 RemoteDisplay, QD204 ScopeScreen, QL460 DriverID or a QS400 SafetyCenter can be connected to this extension. The QS430 SerialExtender does not need configuration for the QD200 remote display to work but it is recommended to consult the documentation on dataport and port_dataport configuration parameters. For in-depth information on SAFEmine Serial Extender configuration and the installation of QS430 please consult with your support responsible or contact support@safe-mine.com. Please refer to the SerialExtender Application Note for further information. 3.4.5. QR310 TrackingRadar QR310 TrackingRadar is a complete subsystem which enables the CAS system to become sensible to bigger obstacles and ground personnel in the close surroundings of the vehicle. Please refer to the SAFEmine TrackingRadar Installation Manual for further information and ask your support responsible for guidance. You may also choose to write to support@safe-mine.com for further assistance. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 15/39 3.5. Connectors SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 3.5.1. Overview The available interfaces on the CAS main unit depend on the models in question. In the following section each of this connectors is specified in detail in order to provide all necessary information for correct connection. The below matrix shows the different interfaces and their presence on the specific main unit models:
Connector QC230 / QC235 QC220 / QC24x QC250 GPS RF GSM/LTE WiFi Main Dedicated Serial I/O SIM-Card Bay 3.5.2. GPS Connector SAFEmine main units include a 50 channel GPS L1 receiver chip with SBAS (WAAS, EGNOS) capability, integrated RAIM (Receiver Autonomous Integrity Monitoring) and active multipath detection and elimination algorithms. The receiver is GALILEO ready. The implemented connector is female with center sleeve contact and outside threads, gold plated SMA for 3.3V active GPS antennas. The wave impedance is 50. Only GPS antennas supplied by SAFEmine may be used. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 16/39 3.5.3. RF Connector SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com SAFEmine includes RF transceiver chips with typically less than 1% duty cycle and effective radiated power (ERP) is below 15mW. The CAS main units make use of the freely available industrial, scientific and medical (ISM) radio frequency bands for short range devices (SRD) and is thus license free. The transmission frequency of the system is software selectable by indicating the specific channel. The country of Origin is Switzerland with a harmonized system customs code (HSCC) 852610. The connector for the RF transceiver is a female SMA with center sleeve contact and outside threads for passive RF antennas with 50 wave impedance. Only RF antennas supplied by SAFEmine may be used. 3.5.4. GSM/LTE/GPRS Connector (only QC220 & QC24x) The QC24x and QC220 SAFEmine devices feature a quad-band GSM/LTE module with embedded TCP/IP stack. The module is Class 4 (2 W) for the 850/900 MHz bands and class 1 (1 W) for the 1800/1900 MHz bands. Its GPRS rating is class 10 (4 downlink, 2 uplink, max. 5) and mobile station class B module. It supports PBCCH ,CS1 to CS4. The module is approved for AT&T, R&TTE, CE, GCF, FCC, PTCRB and many more. Please contact your SAFEmine contact if you require further information. The connector is a reverse polarity female SMA (RP-SMA) with center pin contact and outside threads for passive GSM/LTE Antennas with 50 wave impedance. Only antennas supplied by SAFEmine may be used. 3.5.5. WiFi Connector (only QC250) SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 17/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com The QC250 SAFEmine devices include a self-contained WLAN module. The module is a complete IEE 802.11 b/g/n based wireless device. The module supports WPA2-PSK, WEP (64 and 128 bit) and TKIP security encryption. The typical transmit power is 17dBm for 801.11b, 15dBm for 802.11g/n. The sensitivity is -97dBm @
1Mbps to -71dBm @65 MBps. The connector is a reverse polarity female SMA (RP-SMA) with center pin contact and outside threads for passive WiFi Antennas with 50 wave impedance. Only antennas supplied by SAFEmine may be used. 3.5.6. Main Interface The main interface has a 8-pin M12 male connector. This interface is connected to the vehicle and optional add-on modules. It provides the connection points for power supply and communication ports a dedicated voice signal line as well as one configurable digital I/O:
Pin Color Symbol Function Min. Typ. Max. 1 White
+Vbatt Power supply from Battery
+9Vdc
+12Vdc
+24Vdc
+28Vdc Brown
-Vbatt Green CAN-low Yellow CAN-high Power ground from Battery, connected internally to system ground GND CAN-Bus Port (ISO-11898) Grey Pink Rx Tx Blue I/O1 Serial Communication Port
- QC23x: RS485
- QC220/2240/250: RS232 Configurable1 Digital Input / Output Red Audio Signal wire for SM Voice output
-Vbatt GND GND GND GND GND
+Vbatt
+Vbatt
+Vbatt
+Vbatt
+Vbatt 2 3 4 5 6 7 8 1Please consult chapter 4.6 for general instructions on configuration of I/Os. Use of CAN-Bus, Serial Port, I/O1 and Audio connection depends on the application. They may be left unconnected if not used. The main interface also includes a hardwired input (I/O0) which is internally connected to pin 1 in order to monitor the power supply voltage. The SAFEmine CAS system can operate with a supply voltage down to 9Vdc, but if the supply voltage is below 9.6V at startup, an error code or a message indicating the low supply power is displayed and the device will refuse service. If the supply voltage drops below 9.6V during operation, the power LED will turn red and the error message is issued. In case the voice option is enabled error SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 18/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com power is announced every 30 seconds on the speaker as long as the supply voltage is sufficient to do so. 3.5.7. Display / Serial Connector (only QC230 & QC235) The QC230/35 MainUnit has a female 4-pin M8 display connector and is placed next to the main connector interface. On the QC24X/220/250 devices the display connector has been integrated into the main connector and is branched out through the QM106 serial Y-cable. This connector provides the data and power necessary for the display. The display connector can also be used for debugging and firmware update purposes. The protocol used on the display serial connector is standard RS232 Pin Color Symbol Function Min. Typ. Max. Brown Vsupply 1 Power supply for displays White Rx Serial Communication Port2 Input Blue GND System ground for displays
+9Vdc GND GND Black Tx Serial Communication Port2 Output GND
+12Vdc
+24Vdc
+28Vdc Vsupply Vsupply Vsupply 1 2 3 4 1The display power supply on QC230/235s is stabilized to 12V whereas on QC220/240/250s it is directly connected to +Vbatt 2The serial communication port is used for the display communication as well as for configuration, programming and debugging. 3.5.8. I/O Connector (only QC220/240/250) The I/O connector is an 8-pin M12 male type. The general purpose input output (GPIO) ports present on the I/O interface of the device can be used to monitor and record vehicle parameters such as:
reverse gear, seatbelt clicked, bucket position, bucket load, fuel gauge, etc. The vehicle signals can be used to influence the behavior of the CAS system in order to react to different situations. Additionally, the traffic and GPS information gathered by the CAS MainUnit can be used to trigger outputs in order to control external applications. The GPIOs are almost all on the I/O connector with the exception of ports I/O0 and I/O1. I/O0 is hardwired to the pin 1 of the main connector in order to monitor the power supply voltage. I/O1 is SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 19/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com wired to pin 7 of the main interface and can be used in the same fashion as the GPIOs on the I/O connector. Pin Color Symbol Function White I/O2 Analog Input Brown I/O3 Analog Input Green I/O4 Configurable1 Digital Input Yellow I/O5 Configurable1 Digital Input Grey Pink Blue Red I/O6 I/O7 GND I/O8 Configurable1 Digital Input Output Configurable1 Digital Input Output Signal ground for differential signals GND Configurable1 Digital Input Output GND Min. GND GND GND GND GND GND Typ. Max. Vsupply Vsupply Vsupply Vsupply Vsupply Vsupply Vsupply Vsupply 1 2 3 4 5 6 7 8 1Please consult chapter 4.6 for general instructions on configuration of I/Os. For additional GPIO functionality please refer to the corresponding application note (GPIO AN). If you require any further information please contact with your SAFEmine Supporter. 3.5.9. SIM-Card Bay Interface (only QC220 & QC24X) SAFEmine devices QC220 and QC24X require SIM cards to connect to the local cellular network for data transmission. The amount of data transmission can vary depending on the configurations but a data plan of XXX MB per Month has given good results. For satisfactory online performance of the SAFEmine system the cellphone network service must cover the area of use with either GPRS (2.0G) or EDGE (2.5G). The CAS system does not support higher generation protocols such as UMTS, HSDPA or LTE. The SIM-card bay receives a standard size SIM-card. The Interface is spring loaded and the card has to be pushed in against the spring until a click can be heard. Use a thin nonmetallic piece to help push the card into its place. QC220 and QC24X MainUnits are delivered with a transparent adhesive cover sticker to close the SIM-card bay and protect it against dust. Always install the cover sticker on the SIM-card slot to prevent voiding warranty. Operation of the CAS MainUnit without the SIM card cover sticker voids warranty!
SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 20/39 3.6. Cables SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 3.6.1. QD221 and QD222 Display Extension Cables The QD221 and QD222 display extension cables provide 1.5m and 5m of cable in order to place the QD200 RemoteDisplay or QD204 ScopeScreen visible to the operator and remotely from the main CAS unit. The cable features a male and a female 4-pin plug with a pinout corresponding to the serial interface described in this chapter. 3.6.2. QM101 WiFi Stick Antenna Extension Cable The WiFi stick antenna extension cable is an accessory for the QF0838 WiFi stick antenna. the cable acts as adapter from N-type connector to SMA and is 2.9m long. 3.6.3. QM103 and QS422 CAN-Bus Y-Cables The CAN bus cables are required when using the QS430 SerialExtender. The QM103 cable is equipped with a 120 bus terminator resistance were as the QS422 has no such termination. The cable features a male and a female M12 plug with 8 threads and a female M8 plug with 4 pins. QM103 is used when the QS430 SerialExtender is the only device connected to the can bus. In the contrary case, when both the QS430 SerialExtender and the QR310 TrackingRadar are connected to the CAS unit then the QS422 cable must be used. This is because the CAN bus is terminated by the TrackingRadar installation. In any case consult with your support responsible or write to support@safe-mine.com in order to verify your installation. 3.6.4. QM104 MainUnit Power Cable The QM104 MainUnit power cable is to be connected to battery voltage bypassing the regular vehicle isolation switch. When required, to remain within safety regulations, it is recommended to install a separate isolation switch dedicated only to the SAFEmine system. The QM104 features a female M12 plug and an open ended 2m long pigtail of cable with 8 individual colored threads. The colors indicate the associated pin. Please refer to the tables provided by the Main and I/O Connector Documentation in this chapter. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 21/39 3.6.5. QM105 Power Saving Display Cable SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com The QM105 Power Saving display cable is used to power the QD204 ScopeScreen from ignition, in order to safe power when the ignition is turned off. The CAS MainUnit will remain powered on thanks to its direct connection and continues to provide its service regardless of the ignition status. The cable features a male and a female M8 plug with 4 pins and 2m open ended pigtail to connect to a ignition switch controlled power supply. 3.6.6. QM106 RS232 Serial Communication Y-Cable The QM106 is used to access the main serial connection of the QC220 QC24X and QC250 MainUnits. The cable features a male and a female M12 connector with 8 pins each and a 4 pin M8 female connector for the serial connection. This cable serves for both, connecting the displays or programming the units via serial programming cable. The pinout of this cable corresponds to the pinouts of the main and serial interfaces of the CAS units respectively. Please refer to their documentation in this chapter. This cable replaces the QM109 cable 3.6.7. QM108 Speaker Power and Audio Signal Y-Cable The QM108 Speaker Power and Audio Signal cable is required for SAFEmine Voice installation and connects the CAS MainUnit to the QL015 Loudspeakers. The cable features 2 female and one male M12 connectors. 3.7. Network SAFEmine QC220, QC24X and QC250 MainUnits can provide vehicle tracking functionalities if connected to a SAFEmine Track server (SMTrack). The Movements and status of the vehicles can be consulted through the web interface of the SAFEmine Track server. For additional information consult chapter Error! Reference source not found. of this manual. The following information can be tracked and recorded:
Vehicle Position Vehicle-ID CAS MainUnit serial number Power supply voltage State of the digital inputs and outputs (seatbelt, handbrake, idling, motor hours, etc.) Value of the analog inputs (bucket load, fuel gauge, etc.) Installed firmware version and build number Please consult with your SAFEmine Support contact if you plan to implement this function or write to support@safe-mine.com for further information on this product. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 22/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 4. Hardware Installation Instructions 4.1. General Rules and Best Practices Please check on the following conditions before beginning any work. Differing installations will void the warranty of SAFEmine systems:
Installations may only be carried out by trained electricians. Only antennas supplied by SAFEmine may be used. Unless certified, installation and operation of CAS MainUnits and Accessories must be on the basis of non-interference with existing equipment. When certified, installation and operation must be done according to certification procedures in order to comply with official regulations and requirements. Never connect SAFEmine equipment to critical vehicle signal lines without prior consultation and approval of the vehicle manufacturer and SAFEmine support staff. Connecting the reverse signal to the CAS unit is compulsory in all vehicles that provide such signal. But rather than connecting to critical signal lines use the connection to noncritical signals such as reverse light, reverse buzzer and similar. After installation, an appropriate entry should be made in the vehicles technical logs including CAS MainUnits serial number and the installed firmware version. A check should be performed in order reinsure the installations quality and its accordance with the requirements. Special focus has to be given that the mechanical or electrical performance of other vehicles systems (e.g. radio) is not influenced by the CAS system. SAFEmine highly recommends establishing a Radio Map, containing all intentional transmitters present on the mine and their respective operating frequencies. This map will help identifying potential collisions between frequency ranges and avoid radio interference. If you require 3D models of SAFEmine MainUnits and Accessories, please contact your SAFEmine support contact. 4.1.1. Required Tools SAFEmine strongly recommends using pre-assembled coaxial cabling for quality reasons. However if you plan to lengthen and assemble your own coaxial cabling it is compulsory to use the correct tools. Do not use normal wire cutters or multi-purpose pliers. Inappropriate tools will result in potential faults and downtime. Always use a correctly adjusted 3-Blade wire cutter to strip the coaxial cable and then crimp the center pin with the correct gauge or solder with small tipped, 30 Watt soldering iron. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 23/39 4.2. Main Unit 4.2.1. Prior considerations SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com Install the Main Unit so that it does not interfere with any of the vehicles operations. The selected installation spot must be dry and reasonably free from dust. The CAS MainUnit must not be placed where it could obstruct the operators field of view. At the same time the connectors at the back of the CAS MainUnit should remain easily accessible in order to perform maintenance tasks. A good installation spot provides enough space for the cables and their connectors. Avoid spots where temperatures can suddenly drop. It could cause the buildup of condensation inside the CAS MainUnit. The mount surface should be flat in order to avoid mechanical stresses on the housing of the CAS MainUnit. If the mount surface is metallic it must be insulated from the CAS MainUnit housing If custom mounting plates would be needed, make sure the design does not force the two plastic end-bezels. Doing so would result in bending and consequently damage of the CAS MainUnit. 51mm 4.2.2. Installation Custom mounting plates can be fastened to the lower face of the CAS MainUnit housing using the two 8mm deep M4 blind threads. Do not force screws further than 8mm into the housing. Units damaged through improper handling lose their warranty. Pay attention to metal parts near the CAS MainUnit. The QC units require being completely electrically isolated from any conducting part of the vehicle. If installing QC220 or QC24X CAS MainUnits do not forget the provided cover sticker for the SIM-card bay. Operation of the CAS MainUnit with uncovered SIM-
card slot voids its warranty. 70mm 4.2.3. Cabling Main unit bottom view The GPS, RF and Network (GSM/LTE/WiFi) cables must be tightened with an 8mm spanner in order to prevent manual removal or eventual loosening through vibration. The power cable needs to be connected directly to the battery contacts, bypassing the ignition and the isolation switch. This is to ensure the CAS system keeps working even when the vehicle is switched off or being serviced. A 3A fuse is required in the power connection for both power and ground. Sealable fuse holders are highly recommended. Furthermore, the fuses should be secured with a cable tie to prevent tampering and make manipulations visible. Do not bend any cable further than its minimum bending radius. Transmission in coaxial cables will deteriorate substantially while data and power cables risk to be sheared off. Cables need to be long enough in order to avoid tension. If the installed cable is under tension, relocate the CAS unit or reroute the cable. If neither is possible replace the cable by a longer one. Install the cables in a way (cable ties) allowing easy service and removal. Do not route them over or under access doors or removable plates. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 24/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 4.3. Displays 4.3.1. Prior Considerations The display should be positioned such that the front panel LEDs are in direct view of the Operator, the acoustic warning tone can be heard loud and clearly and control button can be operated easily. The view on the front panel display may not be obstructed at any time. The display may never interfere with the operation of the vehicle (incl. emergency procedures) Special attention is required to not reduce the operators field of view. The displays can also be used with CAS MainUnits which do not explicitly require an external display, e.g. QC235 and QC220. Please contact SAFEmine for more information regarding this configuration. The remote display connection contains the data and power from the main unit. 4.3.2. QD200 Remote Display The QD200 Remote Display has a male M8 type connector with 4 contacts. It connects to the QD221 and QD222 extension cables. To connect with QC230 or QC235 no further cables are required. It can be connected directly to the display interface of the CAS MainUnit. To connect with QC220, QC24X or QC250s, a QR106 Y-cable is required in order to connect to the main interface of the CAS Main Unit. The back side of the displays aluminum housing M8 Mounting Hole M8 Serial Connector SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 25/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com includes two 8mm deep M4 blind threads, so that the housing can easily be secured. Forcing screws longer than 8 mm into the nuts may cause damage and voids warranty. The remote display is light enough to be fixed with 3M dual lock. This is ideal for installations where the owner of the vehicle does not permit to drill holes in the dashboard. 4.3.3. QD204 Scope Screen All connectors are on the rear of the unit. The device can be installed with minimal effort and time, no IT and no radio infrastructure are required. Maintenance instructions for Scope firmware can be found in Appendix M 4.4. Antennas 4.4.1. Prior Considerations In order for the SAFEmine CAS system to operate, the installation of GPS and RF antennas is required. The antennas provide access to the geolocation information from GPS-satellites and enable the communication between SAFEmine CAS MainUnits on the different vehicles. For optimal performance of the SAFEmine CAS system the both GPS and RF antennas must be placed in the topmost position in order to provide free paths to broadcast and receive signals. The best option is to install the antenna on top of the roof. The antenna should not be mounted near metal structures for the same reasons. Leave at least 1m of space between the antenna and the nearest metal surface (with exception of the antenna pole itself). In order to avoid interference or crosstalk with other antennas, leave enough space between any two antennas. SAFEmine requires a distance of at least 1m from any other antenna. The antenna cable is the most sensible component of all of the SAFEmine system and requires proper installation by a trained and experienced electrician. Failing to conduct a correct installation of the high frequency coax cables is the most common cause for malfunction. In order to keep the configuration workload low it is highly required to keep the same antenna position for each vehicle type. E.g. if you equip the first single cab pickup truck with the antenna at the center top of the rollover bar then you should continuing doing so for every following single cab pickup truck of the same model. To guarantee the best possible transmission of the signal from and to the antennas, the bending radius of the coaxial cables must never fall below the minimum specifications. Bending the cables in a tighter curve would mean to introduce losses of signal strength and wave reflection points in the cable. If a cable got overly bent it must be replaced. Buildup of snow, ice and mud can reduce the range and performance to the antennas. Remove all deposits prior to operation. SAFEmine supplies special mounting brackets for various vehicles. Please contact your SAFEmine contact for more information. Resuming the general installation rules for antenna installations, the GPS/RF antennas must be:
Installed. The CAS MainUnit cannot operate without GPS or RF antennas. Mounted on the highest possible point of the vehicle, ideally with 360 unobstructed view of the surroundings and the sky. At least 1m from any metal structure. At least 1m away from any other antenna. Only specific cable types and lengths are admissible. Please consult chapter 4.4.4 on antenna cabling for more information. Positioned at the same spot for a specific vehicle model. Connected to their correspondent inputs. Always connected to cable installations that respect the minimal cable bending radius. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 26/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 4.4.2. Antennas on Haul Trucks It is not always possible to position the antenna on the topmost location. On haul trucks the bucket might be covering the entire structure of the vehicle and thus making the installation of an antenna on the top rather impractical. In this case SAFEmine recommends using a pole on which the antenna can be mounted. The best position for the antenna is one of the front corners. If the vehicles transit on the right side of the road than the left corner is most appropriate and vice versa. The pictures below show different configurations for pole sizes and positions. Antenna positions in the above side view improve from left to right:
The left most picture shows an antenna directly under the canopy. The Antennas reception is very bad. In the second picture the antenna is positioned lower but still has bad reception due to being under the canopy. The third picture shows an acceptable position. The antenna is not covered by the canopy and is at least 1m from any metal structure such as the canopy, the handrail or the cabin platform. The fourth picture on the right extreme shows the antennas recommended ideal position. In the above top views:
The left picture shows how the canopy shields a considerable part of the GPS and RF. This is why the right picture is SAFEmines recommended position. 4.4.3. Antennas on Tracked Vehicles On tracked vehicles, the antenna must be mounted as close as possible to the axis of rotation. For better accuracy, especially to sense a turning maneuver on the spot without losing heading, is to use two SAFEmine units in a master/slave configuration, minimum 5m apart from each other. If you require setting up such a configuration, please consult chapter Error! Reference source not found. on rotating vehicles. 4.4.4. Coaxial Antenna Cabling The selection of coaxial high frequency antenna cables and connectors must be done carefully. SAFEmine recommends to source readily confectioned coaxial cables with SMA connectors already installed and quality checked. It will save precious installation time and avoid faultfinding and rework. Source cables from a professional local supplier. High frequency cabling work must be carried out professionally by trained personnel. Do not save costs on the coaxial cables and connectors. SAFEmine recommends only using high quality components. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 27/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com Be vigilant of the maximum cable length. Re-rout if necessary. Consult the below list for more information. If you plan to cut your coaxial cables to length and crimp the connectors yourself please attain to the following:
The maximum acceptable attenuation for cables and connectors is 3dB/10m @ 900MHz Better: The required overall attenuation for a cable and its connectors must be below 5dB. The inner conductor must be a solid core Find below the recommended maximum cable length between antenna and main unit per cable type based on a maximum attenuation of 5dB for the overall connection. These values are indications and may vary between manufacturers of coaxial cables. Please see the datasheet and send it to SAFEmine prior to the installation. Cable Types1:
RF @950MHz GPS @1.575GHz GSM/LTE @
WiFi @ 2.4GHz RG58 RG174 HDF-195 CDF-195 LMR 195 RF195 LMR-200 LMR-400 6.5m 4.9m 12.0m 4.5m 3.7m 9.8m 1.9GHz 3.9m 3.4m 8.9m 3.4m 3.0m 7.9m 14.0m 36.8m 10.9m 28.6m 9.9m 26.0m 8.8m 23.1m 1Use of different coaxial cable types requires prior written approval by SAFEmine. To calculate the attenuation rate, sum up the attenuation of all segments as specified by the cable manufacturer and add 0.3dB for every SMA connection. Below you will find SAFEmines requirements regarding antenna cable installations:
Respect the minimum bending radius. Typical minimum bend radius for RF195 type cables is 1.8cm (3/4 in. or your thumb) for a one time bend (i.e during installation), 5cm (2 1/3 in. or your fist) for repeated bending (i.e after installation). It is highly recommended to add a braided sleeve around the cables for further UV and abrasion protection. Connections in the antenna cable must be sealed over the whole assembly with heat shrink tubing (glue type). Outside connections must be sealed with silicone tape to ensure a reliable, weatherproof operation. Never use electrical tape (e.g. black PVC tape) to weatherproof RF connections No installation may have more than one (1) connection All antenna cables must be carefully tied to the vehicle. Loosely vibrating cable will fatigue and the central conductor will break over time. Make all cables removable to prevent them from being cut when the vehicle is being serviced. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 28/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com Wear and damage to the RF and GPS antenna cables is not covered under warranty. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 29/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 4.4.5. SMA Coaxial Cable Connectors Waterproofing connection: The coaxial cables contain a white plastic separator between the screen shield and the center core conductor. This plastic is a dielectric material which has the property to absorb water. SMA connectors are not sealed and thus tend to permit water entry from rain and condensation. When the dielectric material in the coaxial cable begins to absorb the water, the cables signal transmission capacity is severely compromised. Signal loss and bad GPS reception are the consequences. SAFEmine strongly recommends using sealing, so called self-amalgamating tape in order to waterproof the SMA connections. Do not use the common vinyl electric insulation tape since it does not provide a waterproof sealing for the connection. Please attain to these recommendations for any SMA connection installed outside the cabin:
Do not use electrical tape or insulation tape. They tend to unwrap by themselves and do not provide a waterproof protection of the connection. See explanation below. Protect the connection with self-amalgamating or self-fusing tape instead. This seals the connector from the environment. As an alternative to Heat Shrink can be used over the whole connection. In harsh conditions it is recommended to use both the heat shrink and self-fusing tape. Custom cable length: If the coaxial cables are being cut to length and confectioned with SMA connectors, please attain to the recommendations of the manufacturer as well as the following best practices recommended by SAFEmine:
Do not use a knife to cut the cable. Damaging or scratching the shield screen or the center core would lead to signal losses and deteriorate the performance of the system. Use a 3-blade coaxial cable stripper tool instead. Adjust the stripper tool blades to the depth as recommended by the SMA connector manufacturer. See below for an example. Use solid core coaxial cables. See explanation below. Solder the center pin. Solid core vs. stranded core: Although having a stranded inner conductor makes the coaxial cable more flexible and less prone to breaking, it is also makes confectioning the cable with SMA connectors more sensible to correct installation procedures of the center pin. Without the appropriate tools such as a 3-blade coaxial cable stripper and especially the center pin crimping pliers, it is almost impossible to consistently create high quality connections. Therefore SAFEmine recommends using solid core coaxial cable and soldering the center pin to the core if youre planning to cut the cables to length. Please send your SAFEmine supporter the datasheets of the cables and SMA connectors prior to installation in order for assistance. 4.4.6. Antenna Cable Conduit Through-hole mount antennas are delivered with an at least 30cm long cable conduit sleeve to prevent the antenna cabling to brake due to repeated bending fatigue when vibrating. The installation of the cable conduit is compulsory for every SAFEmine CAS installation using through-hole antennas. The correct installation will ensure the robustness of the CAS system. To do so please attend to the following rules:
SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 30/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com First, protect the RF cable in a braided sleeve for the whole length of the coaxial cable, from the antenna to the CAS unit. Use zip-ties at the beginning and the end of the cable to tie the braided sleeve to the coaxial cable Do not cut the left-over of the zip tie to ensure the coaxial cable does not move freely inside conduit. Insert the coaxial cable protected with the braided sleeve into the cable conduit. Attach the cable conduit mechanically to the nearest possible structure: antenna bracket, antenna pole, hand rail or chassis. The free, unattached length of the conduit should be 15cm long, but never longer than 30cm. Respect the bending radiuses for coaxial cabling!
Remember to follow the water-proofing rules described above before installing the sleeve and the conduit. 4.4.7. Through-Hole Mount Antennas (QF012, QF020, QF036) The through-hole mount antennas are the recommended antennas for permanent installations due to their strong mechanical attachment to the vehicle. The following section describes the general recommendations for installation procedures specific to this type of antennas. The through-hole mount antennas have the following properties:
A threaded metal shaft, which receives a 20 threads nut. The shaft is hollow giving path to the pigtail of 2 or 3 approx. 10-15cm long coaxial cables. The cables are confectioned with standard male SMA connector for GPS and RF signal cables and a reversed male SMA for the WiFi signal cable. The shaft thread is with 20 threads per inch and is long. The through-hole mount antennas are shipped with the matching Nut and a isolating nylon washer. The attached gasket provides a sealant to prevent moisture from entering through the mounting hole. Do not use the triple antenna (QF036) for GPS, RF and GSM since RF and GSM signals will interfere and render the system non-operational. Instead use a combination of GPS+RF antenna
(QF012) on the roof with a separate adhesive GSM/LTE antenna (QF034) in the cabin. In order to mount the through-hole antenna the following operations must be performed:
The antenna requires to be mounted on a horizontal metal surface which is in diameter 1-
2cm larger than the diameter of the antenna. Any metallic surface larger than this is acceptable. If no such surface can be provided, mount an extra surface at least XXcm wide as mounting surface. A hole must be drilled or punched into the surface. The diameter of the hole must be at least 22mm (0.866") in order to fit the antenna and the compulsory insulating washer. The surface should also not be thicker than 12mm (1/2") in order for the threaded shaft to protrude through the mounting surface. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 31/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com In order to secure the antenna mounting with the provided insulating washer and nut it is necessary to have access to the backside of the mounting surface. Metallic Surface: It is compulsory to use a metallic surface as a mounting platform. The metallic surface provides an effective shield against ground reflections of the GPS signal and helps to improve RF connectivity. To omit the metallic mounting surface can result in poor GPS positioning and decreased range of RF communication. Finally to attach the antenna the following steps are necessary:
From the top side:
After removing the nut and the washer from the threaded shaft feed the cables through the hole of the mounting surface. Insert the threaded shaft through the hole until the antenna is sitting flush with the soft foam cushion on the metallic surface. From the back side:
Feed the cables through the insulating washer from the narrower end. Slide the washer over the shaft such that the narrow part of the insulating washer sinks into the space between the shaft and the mounting hole. Make sure the insulating washer lies flush on the back side of the mounting surface. If this is not the case, carefully reduce the height of the small neck of the insulation washer. Do not remove it completely since this would render the washer useless threaded shaft could and electrically the mounting surface. contact with the Next slide the nut over the cables and screw it on the threaded shaft. The nut should be tightened with a torque of 5 ft-lb or 6.8 nm in order to properly seal the gasket. Tighten the nut with a wrench. Finally, feed the cables to the jumper thru additional receiver cables. Insulating washer: The threaded shaft of the antennas must always be isolated from the vehicle in order to avoid ground loops. to achieve a reliable isolation between the antenna shaft and the metallic mounting surface it is compulsory to install the insulation washer. this washer possesses a small neck which isolates the inner hole surface from the threads on the antenna mounting shaft Suitable insulating washers are available from SAFEmine and can be ordered separately if needed. Please contact your SAFEmine support responsible if you have any questions regarding the best practices and potential pitfalls when installing through-hole mount antennas. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 32/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com In the picture above, the cables in the cable conduit of the through-hole antenna should have a free cable portion of 15 to maximum 30 cm until the first attachment to the pole or frame. Keep a gentle curve of the cabling but dont permit the free portion of the cable to be too long. Otherwise the cabling is in danger of braking through bending fatigue. 4.4.8. Magnetic Mount Antennas (QF024, QF026, QF037, QN555) These antenna types are the preferred solution for light vehicles, demonstrations, contractor vehicles and in general vehicles which do not provide the possibility to mount a through-hole antenna. Installation on heavy equipment such as haul trucks, excavators or dozers is not recommended, due to the strong vibrations these vehicles are exposed to. The magnetic mount antennas are equipped with 3.5m cable harnesses, either with two cables for GPS and RF (QF024, QN555), two cables for GPS and GSM (QF026) or with three cables for GPS, RF and WiFi (QF037). Do not use the triple antenna (QF037) for GPS, RF and GSM since RF and GSM signals will interfere and render the system non-operational. Instead use a combination of GPS+RF antenna
(QF024) on the roof with a separate adhesive GSM/LTE antenna (QF034) in the cabin. The antennas can be located on any flat magnetic surface, preferably on top of the roof, where it has free view of the sky. Pay attention to install the antennas such that they are not covered by any electrically conducting surfaces as metal of carbon fiber nor should they be mounted immediately alongside such materials. As the through-hole antennas, the magnetic mount antennas require a mounting surface with a diameter of at least 18cm. This ensures shielding from ground reflections of the GPS signal and significantly improves the radiation characteristics of the RF antenna. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 33/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com 4.4.9. Adhesive Mount Antennas (QF028, QF034) The adhesive mount antennas are designed to be attached to a non-conducting surface, preferably the front windshield. The QF024 antenna is a GSMonly antenna meant to be installed in the cabin with QC24X MainUnits in addition to a GPS+RF roof antenna (either QF012 or QF024). The QF034 is a combined GPS+GSM/LTE antenna which is dedicated to installations which use the QC220 MainUnit. The antennas come with a 2.4m (8 foot) long coaxial cable and a male SMA connector. The GSM/LTE antennas must be installed such that:
In cabins with metallic roof, a minimum 1m distance is maintained from the SAFEmine GPS/RF antenna and any other antenna emitting in the 800MHz to 2.4 GHz range. If the roof is non-metallic increase the minimum distance to 2m. At least 5cm clearance is given from any metal structure (i.e. four fingers wide). The antenna is mounted inside the vehicle in a dry place. The antenna is mounted vertically. The cable of the antenna is perpendicular to the antenna and does not bend for the first 5cm. 4.4.10. Bracket Mount Antennas (QF038) SAFEmine supplies bracket mounts for QF038 WiFi Stick Antennas. The bracket is used to mount the antenna on a rail or tubing. As with all SAFEmine equipment, electrical insulation between the metal structure and the metallic antenna parts must be ensured at all time in order to avoid ground current loops. Please refer to your support responsible or write to support@safe-mine.com for further information. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 34/39 4.5. GPIO Connections SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com The CAS system offers to interact with its environment through eight general purpose input/output ports. The outputs may drive (source or sink) 400mA each and at the same time. The inputs are designed to work on switches, providing either pull-up or pull-down configurations. Due to the multi-purpose nature of the CAS GPIO input/outputs it is not possible to galvanically isolate them. If galvanic isolation is required install a protection relay in the signal path. Further, always connect inputs/outputs to non-sensible systems. Since the CAS system is permanently powered, it must be made sure it can never feed current into a potentially dangerous subsystem. For example: Always connect the reverse gear sense line to the switch side, which connects to the buzzer or the strobe for reversing. Never connect on the relay coil side or on a driving output!
It is compulsory to mount protection relays when the inner workings of signal sources are not completely understood or the receiving subsystem might act unexpectedly. The following schematic shows the recommended connection to the reverse switch signal in a vehicle with negative isolation switch (as found in Caterpillar and alike). SAFEmine CAS Protection Relay Reverse Switch Battery Vehicle load Isolator Switch This configuration prevents eventual currents flowing from the CAS reverse input to the vehicle systems when the isolator switch is opened or the negative connection of the CAS should become disconnected. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 35/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com Appendix A FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Per FCC Rules, changes or modifications not expressly approved by SAFEmine could void your authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Appendix B RF RADIATION RF Radiation Hazard Warning To ensure compliance with FCC and Industry Canada RF exposure requirements, this device must be installed in a location where the antennas of the device will have a minimum distance of at least 20 cm from all persons. Using higher gain antennas and types of antennas not certified for use with this product is not allowed. The device shall not be co-located with another transmitter. Installez l'appareil en veillant conserver une distance d'au moins 20 cm entre les lments rayonnants et les personnes. Cet avertissement de scurit est conforme aux limites d'exposition dfinies par la norme CNR-102 at relative aux frquences radio. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 36/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com Appendix C IC COMPLIANCE Industry Canada Notice and Marking 7.1.2 if detachable antenna This radio transmitter RS9110N1122 and NRF905 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Antennatype Mounting type Weight Impedance WIFI gain RF gain GPS gain QF036 Through Hole 480g QF037 Magnetic 620g 50 Ohm Nominal 5 dBi 3 dBi 5 dBi 7.1.2 (applies to all transmitters) Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. 7.1.3 - unlicensed This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 37/39 Appendix D LEGAL STATEMENT WARNING OF PERSONAL INJURY SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com As with all traffic awareness and collision avoidance devices, SAFEmine products may not detect all threats within the detection window. SAFEmine products are intended as an additional tool in determining potential traffic threats, supporting an alert and conscientious driver. SAFEmine products are not designed as a substitute for proper safe driving and visual traffic scanning procedures; a vigilant effective lookout is required at all times. SAFEmine products only warn the operator of the presence of other vehicles that are also fitted with SAFEmine products or warn of obstacles that are stored in the internal database. SAFEmine products do not give any guidance on avoiding action. The operator of the vehicle remains fully responsible for operating the vehicle and ensuring the safety of passengers, pedestrians and other traffic. Never use SAFEmine products for applications other than their intended and authorized use. Never use SAFEmine products as emergency stop device or in any other application where failure of the products could result in personal injury. Before installing, handling, using or servicing SAFEmine products, consult the data sheet, manuals and application notes and make yourself thoroughly familiar with the operations and limitations. Failure to comply with these instructions could result in serious injury or death. LIMITED WARRANTY EXCEPT FOR THE WARRANTIES EXPRESSLY SET FORTH HEREIN, SAFEMINE MAKES NO WARRANTIES, EITHER EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCT. ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED AND DECLINED. SAFEMINE is only liable for defects of this product arising under the conditions of operation provided for in the data sheet and proper use of the goods. SAFEMINE explicitly disclaims all warranties, express or implied, for any period during which the goods are operated or stored not in accordance with the data sheet. The warranty voids in the case of the following cases: any opening of the housing, inappropriate operations or installation (see the restrictions in the respective manuals) and intellectual property violations. SAFEmine Ltd.s entire liability and customers exclusive remedy for SAFEmine products that fail to conform to SAFEmine Ltd.s limited warranty, shall be, at SAFEmine Ltd.s sole option, either repair or replacement of the nonconforming products, or, if neither is practicable, a refund of the fees paid by customer to SAFEmine Ltd. for such products. The warranty for the repaired or replaced product is limited to the scope and remaining duration of the original warranty for the nonconforming product. LIMITED LIABILITY SAFEmine Ltd. does not accept any liability arising out of any application or use of any product or circuit and specifically disclaims any and all liability, including without limitation consequential or incidental damages. All operating parameters, recommended parameters, must be validated for each customers applications by customers technical experts. Recommended parameters can and do vary in different applications. SAFEMINE LTD.S LIABILITY TO CUSTOMER ARISING OUT OF OR RELATING TO ANY SAFEMINE PRODUCTS SHALL NOT EXCEED THE AGGREGATE AMOUNTS PAID BY CUSTOMER TO SAFEMINE FOR SUCH SAFEMINE PRODUCTS. IN NO EVENT WILL SAFEMINE LTD. BE LIABLE FOR LOST USE, PROFITS, REVENUE, COST OF PROCUREMENT OF SUBSTITUTE GOODS, OR ANY OTHER SPECIAL, INDIRECT, RELIANCE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, HOWEVER CAUSED AND UNDER ANY THEORY OF LIABILITY RELATING HERETO. Radio band frequency allocation and licensing conditions may vary from country to country. The operator is solely responsible for ensuring that SAFEmine products are operated in conformity with the applicable telecommunication laws. If the customers uses SAFEmine products for any unintended or unauthorized application, the customer shall defend, indemnify and hold harmless SAFEmine Ltd. and its officers, employees, subsidiaries, affiliates and distributors against all claims, costs, damages and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if SAFEmine Ltd. shall be allegedly negligent with respect to the design or the manufacture of the product. including without limitation SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 38/39 SAFEmine (part of Hexagon Mining) Baarerstrasse 133, CH-6300 Zug Switzerland www.hexagon.com INDEMNIFICATION Customers agree to indemnify and hold harmless SAFEmine Ltd., its subsidiaries, and affiliates, and their respective successors and assigns, from and against all third party claims, loss, damage or expense, and any other liabilities whatsoever, including without limitation, reasonable counsel fees, arising from or by reason of any actual or claimed damages, and/or injuries, or any litigation based thereon, which may be incurred by SAFEmine Ltd. with respect to any of the SAFEmine products covered by the order, including use, and such obligation shall survive acceptance of the SAFEmine products and payment therefore by the customer. INFRINGEMENT SAFEmine Ltd. does not warrant that products and its use will not infringe any patent, copyright or trademark. No specification shall constitute a warranty, express or implied, against any claims for infringement of patents, copyrights or trademarks. Customer shall indemnify and hold SAFEmine Ltd., its subsidiaries and affiliates, and their respective successors and assigns, and its customers harmless from any and all third party liability for such infringement, including without limitation damages, costs, expenses (including reasonable counsel fees), and lost profits arising from any claim that the use of any goods supplied under the invoice infringe any patent, copyright or trademark rights. SAFEmine Ltd | www.safe-mine.com | support@safe-mine.com 39/39
1 | Internal Photos | Internal Photos | 857.65 KiB | September 10 2019 |
Annex B 1-8036/19-01-01_AnnexB Internal photos of the Equipment Under Test This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized:
Marco Bertolino Lab Manager Radio Communications & EMC CTC advanced GmbH Untertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: mail@ctcadvanced.com Photos Photo 1 Photo 2 2019-05-07 Document No. 1-8036/19-01-01_AnnexB 2/4 Photo 3 Photo 4 2019-05-07 Document No. 1-8036/19-01-01_AnnexB 3/4 Document history Version Applied changes initial release
- END OF DOCUMENT -
Date of release 2019-05-07 2019-05-07 Document No. 1-8036/19-01-01_AnnexB 4/4
1 | External Photos | External Photos | 672.69 KiB | September 10 2019 |
Annex A 1-8036/19-01-01_AnnexA External photos of the Equipment Under Test This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized:
Sumit Kumar Testing Manager Radio Communications & EMC CTC advanced GmbH Untertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: mail@ctcadvanced.com Photos Photo 1 Photo 2 2019-04-30 Document No. 1-8036/19-01-01_AnnexA 2/5 Photo 3 Photo 4 2019-04-30 Document No. 1-8036/19-01-01_AnnexA 3/5 Photo 5 Photo 6 2019-04-30 Document No. 1-8036/19-01-01_AnnexA 4/5 Document history Version Applied changes initial release
- END OF DOCUMENT -
Date of release 2019-04-30 2019-04-30 Document No. 1-8036/19-01-01_AnnexA 5/5
1 | Label | ID Label/Location Info | 175.63 KiB | September 10 2019 |
Label Label location Made in Switzerland Pat. Pending Label
1 | FCC Confidentiality Request | Cover Letter(s) | 115.85 KiB | September 10 2019 |
1 rae js Al 448 a i, = ome a - wrt, 2B 3 fs 4 7 aT aa Bs goal Moet ASC, eg
eee bt alte a we as a feos Oy hok rea ee ala ee ie ie is iptlanelr A ele rae |
re cg SE etl yk er ie eh ieee, of Dep ea ge aL ies bo Tea ot ory = > Set I if , ot a) eer ot at . eee Seat prey aa en Nar dey eee rn te ee AS ics uate et
. bos tie BR ey sr cs = oe, Sed oe a sie es finns eae RR ea ee ge ges te Sia ee ener Tes ha pee ee Rela ae abe F a ee a LS ei Wie - See = may, oe ee nS Bel ce a ee x feet pees ska aw
- 1
' a i : a oh a is de Me ene ; rT aca his ER ee ae ae ers eS ea Pursuant to Paragraphs 0.457 and 0.459 of the Commission's Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:
For the product stated above, we request permanent confidentiality for exhibits wnic contain Operational Description, Block Diagram, Schematics, Parts Lists or Tune Up Information. CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branc 435 Oakland Mills Road olumbia, MD 21048 he above exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. me at the address shown below. Andre Reichmuth Safemine Ltd. Baarerstrasse 13 CH-6300 Zug Switzerland andre.reichmuth@hexagon.co LKSQC242/
05/16/2015 incerely
1 | Professional Installation Justification | Cover Letter(s) | 169.06 KiB | September 10 2019 |
Safemine
(Hexagon) Safemine
(Hexagon) safemine
(Hexagon) Safemine Antenna Connector SVewon Frequency range [MHz]
LO 25) Leta At 800-1250 Lee ta AU 0 LO 25) Lee ta A00 824-960, 1710-2600 The device is only sold to a dealer. No sale to retail or to the general public. The device can only be installed by a professional who has completed a special training. A special knowledge to configure a device is needed. The intended use is not for the general public. It is for industry/commercial use. Professional installation does not permit use of any antenna with the transmitter; the permitted types of antenna specified as below. ubject: Professional installation attestatio Bolton Gok safemine Ltd Model No: QC242 Proposed FCC Certification No.: (ZKSQC242A) afemine Ltd confirms the following points regarding professional installation AFEmine (part of Hexagon Mining Baarerstrasse 133, CH-6300 Zug Switzerland T: +41 41 760 856 www.hexagon.com Andre Reichmut Cs) Suey o Whom It May Concern q>
Incerely
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2019-10-09 | 902.4 ~ 922 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2019-10-09
|
||||
1 | Applicant's complete, legal business name |
Safemine Ltd
|
||||
1 | FCC Registration Number (FRN) |
0020866158
|
||||
1 | Physical Address |
Baarerstrasse 133
|
||||
1 |
Zug
|
|||||
1 |
Switzerland
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
T******@ctcadvanced.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
ZKS
|
||||
1 | Equipment Product Code |
QC242A
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
L******** H****
|
||||
1 | Telephone Number |
+4141********
|
||||
1 | Fax Number |
+4141********
|
||||
1 |
l******@safe-mine.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Collision Avoidance Unit | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power listed is peak conducted. This device must be professional installed. RF exposure compliance is addressed for 1.1310 and 2.1091 MPE limits. Installer must be provided with transmitter operation conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
CTC advanced GmbH (former CETECOM ICT Services )
|
||||
1 | Name |
G******** S********
|
||||
1 | Telephone Number |
49-68********
|
||||
1 | Fax Number |
49-68********
|
||||
1 |
t******@ctcadvanced.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 902.40000000 | 922.00000000 | 0.0260000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC