FCC ID: VW3FAST5290V2 Fiber Wireless Router FWR226e

EN Important Information about the Sagemcom FAST 5290 INSTALLATION AND SAFE USAGE INSTRUCTIONS 1. Place the router in a vertical orientation on a flat surface. 2. Connect the manufacturer supplied AC to DC power adapter. The FAST 5290 router requires the use of a 12VDC, 4.1A power adapter. Only use a manufacturer supplied and approved power adapter, power cord and Ethernet cable. Always first plug the mains adapter lead into the FAST 5290, then the mains lead into the mains adapter, and finally the mains lead into the mains socket. If you do not follow this order of connection, you may get an electric shock. Make sure that the mains lead is properly inserted into the power supply unit, and that it is correctly pushed into the recess. It is very important to push the mains lead until the recess bottom. If it is incorrectly connected this may cause a risk of fire or electric shock. 3. Connect the FAST 5290 to the AC Mains in accordance with the installation instructions in this booklet, and the markings on the identification label (voltage, current, and frequency of electricity network). 4. According to installation method required by your ISP:

- Connect the Ethernet cable (provided) to the RJ45 port labeled wan on one end and to the Internet access device provided by your ISP on the other end.

- Connect the MoCA cable (provided by ISP) to the coaxial port labeled MoCA on one end and to the Internet access device provided by your ISP on the other end. 5. For connection of a computer Ethernet cable use one of the RJ45 ports on the product marked 1, 2. Then connect the other end of the Ethernet Cable to the Ethernet port of a computer. Repeat as necessary with the other available Ethernet ports. 6. Battery: Use to connect to the battery with USC Link cable provided by dedicated battery vendor. This port only used to transmit the s ignal data. When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric shock , and injury to persons including the following:

1. Do not use this product near water and avoid contact with moisture. For example, does not use near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Care should be taken so that liquids are not spilled on this equipment. 2. This equipment is for indoor use only, do not place or install in an outdoor location. 3. Ethernet ports are intended to be connected to indoor cable circuits that are exclusively located within the building where the product FAST 5290 is installed, and dont terminate on a remote equipment earthed to a different earthing network. 4. The devices connected to the telephone interfaces must be kept indoor use only. Caution: To reduce risk of electric shock, fire or damage to the equipment, do not connect telephone or telecommunications public network into PHONE port. 5. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 6. Do not use the telephone to report a gas leak in the vicinity of the leak. 7. Make sure the power socket to which you connect the power cord is easily accessible and as close as possible to the equipment so that the appliance can be unplugged quickly in case of a problem. 8. Place your product on a firm, solid surface, no obstacle at a minimum distance of 50cm (1.64 feet). If you put it on something unsteady, it may fall and be damaged. If you place it on a soft surface, such as rug, sofa or cushion, the vents may be blocked, causing the product to overheat. 9. Never insert objects into the vents of this equipment as this can result in the risk of electrical shock or fire. 10. As the power adapter is the only way to connect to the electrical network, the product must be installed near an easily accessed power outlet. 11. This equipment should only be operated with the type of power supply (Voltage and Current) indicated on the marking label. 12. Do not overload wall outlets or extension cords. Doing so can result in the risk of fire or electrical shock. 13. Avoid blocking any vent openings or exhaust exits on this equipment. Do not place equipment in a built-in installation such as a cabinet that may impede the flow of air through the ventilation openings. 14. The equipment should be situated away from heat sources such as radiators, heat registers, stoves, or other heat producing appliances and equipment. 15. To disconnect this equipment from AC power, unplug the power supply from the AC wall socket. 16. Care should be taken to ensure that the power cord is routed, so it is not likely to be walked on or pinched by items placed upon or next to it. 17. Unplug this equipment before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning only. 18. This equipment is not user serviceable and is to be serviced by qualified personnel only. Do not disassemble this equipment. If service is required, disconnect all power from the equipment and consult qualified service personnel. 19. To disconnect this equipment from AC power, unplug the power supply from the AC wall socket. 20. Use the product in the environment specified as below:

- Air temperature between 0C (32 F) and +45C (113 F).

- Relative humidity between 20% and 90%.

- Altitude: 2743 meters (9000feet) maximum. FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. MODIFICATIONS You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void you r authority to operate the equipment. FCC Responsible Party: Sagemcom USA 14651 N. Dallas Parkway Suite 900 Dallas, TX 75254 Phone: 972-674-4100 RADIO FREQUENCY INTERFERENCE STATEMENT Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause har mful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna. 2. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. Increase the separation between the equipment and receiver. FCC RADIATION EXPOSURE STATEMENT This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device produces radio frequency energy in the 2.4GHz, 5GHz and 6GHz spectrum. The antenna must be positioned to keep a minimum distance of 50cm(1.64 feet) from the radiating element to any nearby person. North American Cable installer: This reminder is provided to call the your attention to Section 820.93 of the National Electric Code (Section 54 of the Canadian Electrical code, Part 1) which provides guidelines for proper grounding and, in particular, specifies that the c able ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. FCC regulations restrict the operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or Communications with unmanned aircraft systems. Issued by Sagemcom Broadband SAS Sagemcom Broadband 250, route de lEmpereur - 92500 RUEIL MALMAISON FRANCE Sagemcom Broadband SAS 2022 All rights reserved. Subject to availability. Rights of modifications reserved. www.sagemcom.com

A 20220322 FIRST RELEASE FOR F5290V2,Ues PN 1510-37U0000 Sujing Jeacol Jeacol Sujing Jeacol Sujing Jeacol Sujing Jeacol Sujing Jeacol Sujing 90 4.71*4.71 0 5 90 This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operaon. WARNING This product can expose you to chemicals including Bisphenol-A which are known to the State of California to cause cancer and birth defects or other reproducve harm. For more informaon go to www.P65Warnings.ca.gov Tested To Comply With FCC Standards INDOOR USE ONLY E308616 Printing Content for supplier Scale 1:1 4.71*4.71 4.71*4.71 90 Serial Number: UUYYDDDMMXXXXXX Fiber Wireless Router FWR226e Model: FAST 5290 P/N: 253961806 FCC ID: VW3FAST5290V2 Input: 12V 4.1A Advanced Device Conguraon:

hp://192.168.254.254 Device Access Code:

DoctorBrown1234 0 5 MAC: 40:65:A3:FF:A7:B0 Wi-Fi Network Name:

Froner0030 Wi-Fi Password:

DoctorCurtain3869 Assembled in China Factory ID: F2 This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operaon. WARNING This product can expose you to chemicals including Bisphenol-A which are known to the State of California to cause cancer and birth defects or other reproducve harm. For more informaon go to www.P65Warnings.ca.gov Tested To Comply With FCC Standards INDOOR USE ONLY E308616 Serial Number: UUYYDDDMMXXXXXX Fiber Wireless Router FWR226e Model: FAST 5290 P/N: 253961806 FCC ID: VW3FAST5290V2 Input: 12V 4.1A Advanced Device Conguraon:

hp://192.168.254.254 Device Access Code:

DoctorBrown1234 0 5 MAC: 40:65:A3:FF:A7:B0 Wi-Fi Network Name:

Froner0030 Wi-Fi Password:

DoctorCurtain3869 Assembled in Indonesia Factory ID: F10 This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operaon. WARNING This product can expose you to chemicals including Bisphenol-A which are known to the State of California to cause cancer and birth defects or other reproducve harm. For more informaon go to www.P65Warnings.ca.gov Tested To Comply With FCC Standards INDOOR USE ONLY E308616 Rang label Fonts:

Font: Calibri Printing position for factory Scale 1:1 20 20*3.964MM 2mm 2mm This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operaon. WARNING This product can expose you to chemicals including Bisphenol-A which are known to the State of California to cause cancer and birth defects or other reproducve harm. For more informaon go to www.P65Warnings.ca.gov Tested To Comply With FCC Standards INDOOR USE ONLY E308616 3mm This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operaon. WARNING This product can expose you to chemicals including Bisphenol-A which are known to the State of California to cause cancer and birth defects or other reproducve harm. For more informaon go to www.P65Warnings.ca.gov Tested To Comply With FCC Standards INDOOR USE ONLY E308616 Release paper SPEC 50 White Polyester(Matt)/FASSON_MZ0336A Roll form packaging

Roll type Material (Brand/Model No.):

(ex.PETPPART PAPER(Brand/Model No.)) Adhesive (Brand/Model No):

(ex.Acrylic(Brand/Model No.)) Coating (Brand/Model No.):

(ex.PETOPP(Brand/Model No.)) Printable:

Printing color:

(ex.Black 100%Other) Background color:

(ex.White Other) Packing method:

Safety certification:

Printing ribbon:

Acrylic(Embossed ) Matt OPP Film Yes No Yes No V Black 100%

White Single page Roll V V PGJI2 PGDQ2 California Prop 65(CA 65) NA high temperature ribbon Low temperature ribbon V V NoNo Artwork version (File name / Released date) 20220322 Outer diameter of the paper roll core: 3'(76.2mm)

: 3'(76.2mm) Outer diameter of the paper roll: <8(203mm)

: <8(203mm) Notes 1. During OQC/IQC ,the vendor/CM must inspect all critical items marked with a 2. (): //. Full color printing (excluding single color): Must provide color tolerance sample for customer/RD/PM/ IQC (light tolerance/color specimen/dark tolerance). 3. /: , E < 2, . Spot color/Single color: Must provide color report by Colorimeter, E < 2 or define by coustumer. 4. : . Muse pass abrasion test: Define by coustumer. Material Structure Material Made paper 5. Printing Tolerance is defined in the right column as the choose 6. This part should not contain any substances which are specified in SPT-00001/PMQ-M0003, issued by PEGATRON. 7. , Must attach the detail raw material data sheet when Approval. TOLERANCE SPEC. All Dimension 0.20mm Edge distance 0.50mm GAP distance 0.50mm Rating LABEL A3 FAST5290V2 1510-XXXXXXX Jeacol Jeacol Sujing

emcom Sagemcom toadband Aucapitslde sa. $1 477,36 440294 510RC NANTERRE 250. route d 92848 RUET FRANCE

(0)1

\GEMCOM-

Confidentia ity Request Letter Date:2022-05-17 Federal Communications Commission Authorization and Evaluation Division FCC ID: VW3FAST5290V2 Long Term Confidentiality:

Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby respectfully request confidential treatment of information accompanying this application as outlined below:

@ Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We understand that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this FJe) o)iler-ta lela p Short-term Confidentiality:

This request for confidentiality is made pursuant to 47 CFR 0.457(d)(2) and 0.459 of FCC rules. SAGEMCOM BROADBAND SAS requests that the following documents regarding this submission for FCC ID: VW3FAST5290V2 are kept confidential for a period of 180 days from the date of the Grant of Equipment Authorization. e Test Setup Photos Sincerely, Applicants company name : SAGEMCOM BROADBAND SAS Applicants company address : 250 Route de lEmpereur - 92848 RUEIL MALMAISON CEDEX-

FRANCE Signature Name and Job Title Jacq D General Methods Department Manager E-Mail jacques.leroux@sagemcom.com Tel +33 (0)1 57 61 25 72 Fax +33 (0)1 57 61 38.99 ge co B S.A.S. 2 s Sige Social :

e!Empereur L-MALMAISON CEDEX Tl: +33 5761 1000 Headquarter: 250 Route de l/Empereur 92848 RUEIL MALMAISON CEDEX -

emc m DY -Yomr-]e-1a(elame)m-ANUldalelars-ialelal Date:2022-04-20 We Name: SAGEMCOM BROADBAND SAS Address: 250 Route de I'Empereur -92848 RUEIL MALMAISON CEDEX-FRANCE Declare that:

Name Representative of agent Marlin Chen Agent Company name: MRT Technology (Suzhou) Co., Ltd Address: D8 Building, Youxin Industrial Park, No.2 Tian'edang Rd., Wuzhong Economic Development Zone City: Suzhou Country: China is authorized to apply for Certification of the following product(s):

Product: Fiber Wireless Router FCC ID: VW3FAST5290V2 Model No.: FAST 5290 Sincerely, Sagemcom Broadband S.A.S. Au capital de 58 251 ANT ,36 440 294 510 RCS NANTERRE Sige Social :

289, route de |'Empereur 92848 RUEIL-MALMAISON CEDEX FRANCE Name and Job Title Jacques LE ROUX Tal, 433 (0)1 67 61 10.90 R&D General Methods Depart anager E-Mail: : jacques.leroux@sagemcom.com Tel: +33 (0)15761 2572 Fax: +33 (0)157 613899 SAGEMCONM- Headquarter: 250 Route de lEmpereur 92848 RUEIL MALMAISON CEDEX - FRANCE Ssagemcom

DY=TolFeTe-idelameym Meleliolgriia, Date:2022-04-20 Federal Communications Commission Authorization and Evaluation Division FCC ID: VW3FASTS5290V2 Please be notified that we, the undersigned, SAGEMCOM BROADBAND SAS declares that the product which bears the above FCC ID is also compliant with the FCC requirements for sDOC. And the sDOC procedure shall be carried out prior to marketing the device in the US. Sincerely, Sagemcom Broadband S.AS. Au capital de 53 251 417.36 440 294 510 RCS NANTERRE de /Empreut 92848 RUEIL-MALMAISON CEDEX FRANCE 57 611000 Name and JobTitle : Jacques LE ROUX / R&D General Methods Department Manager E-Mail : jacques.leroux@sagemcom.com 1 +33 (0)157 61 25 72 7) ae +33 (0)157 613899 SAGEMCOWNM- Headquarter: 250 Route de lEmpereur 92848 RUEIL MALMAISON CEDEX - FRANCE

agemcom 440 294 5108 o2848 Fe AEIL-MALMAL can..confi th rodu Software Defined Radio Cover Letter Broac S.AS 5251 4 CS NAN Siege Sacial Final conclusion: 981) roule de Empereur sfe)\aej=18)=9,4 According to the above questions reply, we rm is device (

Description: Fiber Wireless Ro 5290) mu ASDBy 57 61 1090 Jacques LE ROUX / R&D General Methods Department anager Mail : jacques.leroux@sagemcom.com

+33 (0)157 612572

+33 (0)157 61 38 99 SAGEMCOM- Headquarter: 250 Route de !Empereur 92848 RUEIL MALMAISON CEDEX FRANCE Page 1 of 1 Date:2022-04-20 Refer to KDB 442812 DO1 SDR apps Guide v02r03. The following six questions can be used for determining if a radio can elect to be, or must be an SDR. 1. Can the RF parameters of the device be altered through software?

Yes - go to 2. No, not an SDR parties not permitted by the Commission through specific filings modify, configure, or load different software, or make configuration settings to operate the device or host hardware radio frequency parameters (frequency range, modulation type, maximum output power or other radio parameters) in any other way than granted (or expected to be granted)?

Yes, must be an SDR. No - go to 3. 3. Is the device capable of operating in any other way than granted, or will be, granted?

Yes, - go to 4. No - goto 5. 4. Is this a Part 15 client Device as defined in Section 15.202 (as opposed to a master device)?

es, qualifies as a part 15 client devices - go to 5. No, must be an SDR. 5. Does the manufacturer elect SDR?

Yes, elects to be an SDR. No, Not an SDR