EXPE DITION xXP106 Owner's Manual SAMSON Copyright 2013 v1.7 Samson Technologies Corp. 45 Gilpin Avenue Hauppauge, New York 11788-8816 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 631-784-2201 www.samsontech.com The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Samson Technologies is under license. Other trademarks and trade names are those of their respective owners. 2 SAMSON Important Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRONIQUE -
NE PAS OUVRIR WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) AS THERE ARE NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated danger-
ous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance in-
structions in the literature accompanying the appliance. ps4 If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that MMMM requires proper treatment, recovery and recycling. Private household in the 28 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). For Countries not mentioned above, please contact your local authorities for a correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health. XP106 Portable PA System 3 Important Safety Information so oe N 10, Ts, I, Read these instructions. eep these instructions. Heed all warnings. Follow all instructions. io not use this apparatus near water. Clean only with dry cloth. io not block any ventilation open-
ings. Install in accordance with the manufacturer's instructions. 0 not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. io not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electri-
cian for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the ap-
paratus. When a cart is used, use caution when moving the cart/appara-
tus combination to avoid injury from tip-over, 13. 14. 15. 16. 17. 18. ako 20. Unplug the apparatus during lighten-
ing storms or when unused for long periods of time. Refer all servicing to qualified personnel. Service is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. This appliance shall not be exposed to dripping or splashing water and that no object filled with liquid such as vases shall be placed on the ap-
paratus. Caution-to prevent electrical shock, match wide blade plug wide slot fully insert. Please keep a good ventilation envi-
ronment around the entire unit. To prevent injury, this apparatus must be securely attached to the stand in accordance with the installation instructions. WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like. CAUTION: Danger of explosion if bat-
tery is incorrectly replaced. Replace only with the same or equivalent type. Important Safety Information FCC Notice 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compli-
ance could void the user's authority to operate the equipment. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digi-
tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
* Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help. RF Warning Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. This device complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. 0700 XP106 Portable PA System 5 Table of Contents Introduction. 6. zg Fe CUS ee en se ee ctsee tartare ede cdlae eres ee eects etlsel=ts hee eer arias 8 Control-Ranel Features. 2. aw 2 ese we ee ew we g QUICK SIAM vga ww ee Raw Ee wwe ew BG 11 Pairing with a Bluetooth device... ......2.... 12 Charging the Battery... .........2.-. 2004 13 Speaker Placement . 2... 0 6 ee le 14 Avoiding Feedbacks = 2 ase es 44 @ we ea ew He 1S Quick Start - Stage XPD1 Wireless System .... 2... 16 Stage HXD1 Handheld Transmitter Controls... .... 18 Stage RXD1 Receiver Controls . 2... ......... 19 Using the LINE IN/OUT Jack. 22... eee ee ee 20 Making Connections... ........2..2 2005 21 XP106 Specifications ...........2.2.2200. 22 Introduction Thank you for purchasing the XP106 battery-powered portable sound system, featuring wireless Bluetooth connectivity, to stream audio from your smart phone, tablet, or computer. The XP106 is a complete all-in-one solution provid-
ing the flexibility of a fourchannel mixer (with inputs for a microphone and line level devices), a line output for linking multiple speakers, and a Music/Speech tone switch. For added flexibility, the XP106 mixer has a USB jack for connecting the Samson Stage XPD1 digital handheld wireless system, creating a completely cordless performance. Lightweight and compact, the XP106 features 100 watts of power weighing less than 20lbs, makes it an excellent complement to any mobile speaker application. The internal battery provides up to 20 hours of audio on a full charge. The XP106 can also be powered by the included AC adaptor for continuous audio. Whether you are looking for a sound system for use outdoors, in the classroom, for karaoke, for presentations, or performing live music, the XP106 provides high quality, portable audio in a small self-powered package. We recommend you keep the following records for reference, as well as a copy of your sales receipt. Serial number:
Date of purchase:
Dealer name:
With proper care and maintenance, your XP106 will operate trouble-free for many years. Should your speaker ever require servicing, a Return Authorization
(RA) number must be obtained before shipping your unit to Samson. Without this number, the unit will not be accepted. Please call Samson at 1-800-
3SAMSON (1-800-372-6766) for an RA number prior to shipping your unit. Please retain the original packing materials and, if possible, return the unit in its original carton. If your XP106 was purchased outside of the United States, contact your local distributor for warranty details and service information. XP106 Portable PA System 7 Features e Lightweight, 100 watt PA system that weighs under 20 pounds Bluetooth connectivity to connect wireless music sources e 2-way speaker enclosure with 6-inch woofer and 1-inch high frequency driver e Four channel mixer with microphone, line level, and USB wireless receiver inputs. e Integrated 1 3/8-inch speaker stand mount e Ergonomic top carry handle e Internal rechargeable battery for up to 20 hours of continuous use
* System equalization contour switch for music and spoken word applica-
tions e Link output for expanding your sound system Accessories
* XP106 - Dynamic handheld microphone with XLR cable e XP106w - Stage XPD1 digital handheld wireless system with USB receiver and handheld transmitter Control Panel Features 1. 11. 12. 13. 14. XP106 Portable PA System MIC/INST Input - Use this XLR/%" input for microphone, instrument with and active @
preamp or a line signal. LEVEL (CHANNEL 1) - Used to control the level of the CHAN-
NEL 1 Mic/Line input. AUX IN - Connect a line level device using a 3.5mm audio cable. @
LINE Input - 4" input used to connect instrument or line level signals. LEVEL (CHANNEL 2) - Used to control the level of the MP3 IN and LINE inputs. @ =
2.4GHz WIRELESS Input* - Con-
nect the Samson Stage XPD1 digital wireless USB receiver to this input. The wireless receiver gets its power from the XP106, so no additional power supply is needed. LEVEL (WIRELESS) - Used to control the level of the 2.4GHz WIRELESS input. 666 66 G O LINE OUT - %" output connector to link multiple XP106 systems together LEVEL (BLUETOOTH) - Used to control the level of the Bfuetooth input. SPEECH/MUSIC Switch - This switch is used to change the overall fre-
quency response, or tone contour, for the XP106 sound system. If your application is mainly for music, leave the switch up to select the MUSIC response curve. If your application is mainly for spoken word, press the switch down to select the SPEECH response curve. Power - Switches on the main power. PEAK LED - The Red LED illuminates at the level where distortion occurs. Battery Indicator - Displays the status of the battery charge level. DC IN - Connect the supplied power adapter here.
* The USB connector is for the Stage XPDI receiver only. The connector is not designed to charge smartphones, tablets, or similar devices. Control Panel Features 15. Pairing Indicator - Displays the Bluetooth status of the XP106 system. 16. Pairing Button - Press this but-
ton to enable pairing mode in order to connect to a Blue-
tooth audio device. 10 SAMSON Quick Start Follow these steps below to quickly get started using your XP106 portable sound system.
* Set the XP106's power switch to the OFF position, and fully turn all of the LEVEL controls counterclockwise to 0. e If an outlet is available, connect the included power adaptor to the DC IN of the speaker, and plug it into an AC socket.
* Connect a microphone using a standard XLR cable, line level equipment using a4" instrument cable, or portable audio device using a " cable. e Switch on the XP106 power. e While speaking into the microphone or playing music from a line level audio source, slowly raise the channel LEVEL until you have reached the desired level. NOTE: If not using the channel 1 input, turn the LEVEL control all the way down to keep out any unwanted noise. Setting a Good Level Use the Channel LEVEL controls to set the individual volume of your micro-
phone, line level and Biuetooth devices. The PEAK light illuminates when the signal sending to the internal amplifier begins to reach a level where distortion occurs. If the PEAK lights stay on, your mix is too hot and you need to lower the LEVEL controls. It is okay for the PEAK light to occasionally light, however it should go off quickly and should not constantly stay on. XP106 Portable PA System 11 Pairing with a Bluetooth device Bluetooth is a wireless communication technology that allows for connectivity between a wide range of devices. The XP106 uses Bluetooth to stream high quality audio from your Bluetooth enabled device without the need for connecting any cables. In order for your device to work with the XP106 it must first be paired. 1. Turn all channel VOL controls down counterclockwise to 0. 2. With the XP106 and your Biuetooth device powered on; press the PAIR utton on the top panel of the XP106 speaker to make the speaker discov-
erable. The Bluetooth indicator will slowly flash blue. 3. In the settings of your Bluetooth device, set it to discover available devices. 4. From the Bluetooth device list, select the
"Samson XP106" device. 5. If your device asks for a passkey, enter digits 0000 (four zeros) and press OK. Some devices may also ask you to accept he connection. 6. As the XP106 is connecting to your device, he Bluetooth indicator will quickly flash lue. 7. The XP106 speaker indicates that pairing is complete when the indicator turns steady lue. You can now stream audio from your device to the XP106 speakers. Me 8. With the volume control on your Biuetooth device turned up, play some music, and slowly raise the XP106 BLUETOOTH chan-
nel VOL control until you have reached the desired level. 12 SAMSON Charging the Battery The XP106 has an internal, rechargeable battery capal of continuous audio on a full charge. Even though the charge when first taken out of the box, we recommen XP106 before first using the system. To charge the battery:
* Set the power switch to the OFF position. e Connect the XP106 to an AC power outlet using the included power adapter.
* Keep the system plugged in until the Battery indicator changes to green, indicating the battery is fully charged. le of up to 20 hours system may have some fully charging your The XP106 utilizes a sealed lead-acid gel cell battery. When not in use, the battery will slowly self-discharge. If you are planning not to use the XP106 for a long period of time, it is advised to fully charge the unit before storing. It is also important to charge the unit every six months when not used. This will ensure a healthy battery and extend its life. If the battery is left with a very low charge for an extended period of time, it is possible to recharge the battery to working condition, but the charge time can take over 24 hours. If you find that the operation time of the XP106 becomes noticeably decreased, even after fully charging, the battery should be replaced. Contact Samson customer service or your local distributor for a replacement battery. XP106 Portable PA System 13 Speaker Placement The XP106 provides three different placement options for your specific situation. For maximum sound coverage the XP106 can be used with a standard 1% speaker stand. The speaker should be raised above the heads of the listening audience. Take care when placing the speaker on a stand, to ensure that it is on a level, steady surface and will not tip over. Take care when placing the XP106 in direct sunlight for long periods of time, as this may discolor or damage the unit. Do not place the speaker on wet surfaces, as it can cause malfunction. If you notice condensation on the unit, dry the speaker before using or storing. 14 SAMSON Avoiding Feedback Feedback is the annoying fewling and squealing that can heard when the microphone picks up sound from the speaker. The sound is then re-amplified back through the speaker again, creating a feedback loop. Follow these steps to minimize the likelihood of feedback:
e Avoid pointing the microphone directly at the speaker. In general it is recommended that the microphone be positioned behind the speaker enclosure. This uses the directional characteristics of the speaker and microphone to your advantage.
* Keep the microphone as far from the speaker as possible. This will help achieve isolation between the speaker and the microphone, and allow you to increase the output of the XP106.
* Position the microphone as close to the sound source as possible. This will enable the microphone to pick up more direct sound, and allow you to reduce the microphone input gain control. Reduce the overall level of the speaker. XP106 Portable PA System 15 Quick Start - Stage XPDI Wireless System Plug the RXD1 USB receiver into the USB jack labeled 2.4GHz WI RELESS. Turn the WIRELESS LEVEL knob on the XP106 comp letely counterclockwise to O, then turn the POWER siwtch on the XP106 to the ON position. 16
A a
On the wireless handheld transmitter, unscrew the bottom section of the microphone by turning it counterclockwise and then slide it off. Place a fresh set of AA (LR6) batteries in the transmitter battery holder, taking care to observe the polarity markings, then replace the cover. Turn on the power to the transmitter by pressing and holding Power switch;
the indicator LED will light amber. Quick Start - Stage XPDI Wireless System If the handheld transmitter and receiver have not been previously paired, press and hold the button on the RXD1 receiver for >5 seconds, until it begins to flash. Speak or sing into the mic at a normal performance level and raise the WIRELESS LEVEL control until the desired level is reached. XP106 Portable PA System Rt iy Press and hold the Power button on the handheld transmitter >5 seconds. This will put both components into pairing modes. Once the receiver and transmitter communicate and sync, the LEDs on both units will light steady and will be ready for operation. If you hear distortion check the rear panel PEAK LED. If it is lit red, turn down the WIRELESS LEVEL on the XP106 until it lights only occasionally during loud sounds. If you still hear distortion, unscrew the microphone body and use the supplied plastic screwdriver to turn the Gain control in the HXD1 transmitter slowly counterclockwise until the distortion disappears. Conversely, if you hear a weak, noisy signal at the desired volume level (and with the WIRELESS control of the XP106 turned fully clockwise), use the supplied plastic screwdriver to turn the Gain control in the HXD1 transmitter slowly clockwise until the signal reaches an acceptable level. 17 Stage HXDI Handheld Transmitter Controls 1. Status Indicator - This LED displays the opera-
tion mode:
Amber Normal Operation Flashing Amber | Pairing/Low Battery 2. Power/Pair Switch - Press <5 seconds to urn the unit on or off. Press >5 seconds o enter pairing mode. 3. Battery Cover - Unscrew the battery cover and slide down to open the HXD1 battery compartment. 4. Battery Holder - Open the battery holder by pressing the tab and lifting the cover. Insert two standard AA (LR6) batteries here, being sure to observe the plus and minus polarity markings shown. Although rechargeable Ni-Cad batteries can be used, they do not supply adequate current for more than four hours. WARNING: Do not insert the batteries backwards; doing so can cause severe damage to the HXD1 and will void your warranty. 5. Input GAIN Control - This control adjusts the transmitter input sensitivity. This input sensitivity control has been factory preset to provide optimum level for the particular microphone capsule provided with the Stage XPD1 system and so we recommend that this not be adjusted manually. If necessary, however, you can use the supplied plastic screwdriver to raise or lower the input level. Stage RXDI Receiver Controls 1. USB Connector - Plugs into the USB 2.4GHz Wireless jack on the rear panel of the XP106. The receiver can also plug directly into a computer USB port and will be recognized as a USB audio device. The unit passes audio to the device and receives ower from the device through this connector. 2. PAIR Switch - Press >5 seconds to enter pairing mode. 3. STATUS Indicator - This LED displays the operation mode:
Normal Operation Pairing Not Paired; Transmitter Out Of Range;
No Power Flashing Amber No Light XP106 Portable PA System 19 Using the LINE OUT Jack The XP106 LINE OUT jack allows you to connect the XP106 with any powered speaker to expand your system or link two XP106 systems together and share all inputs between the two units. You can also use the jack to receive audio from another speaker without using an input channel. Daisy Chain Speaker Using a standard shielded 4 instrument cable, connect the LINE OUT on the XP106 to a line level input of second powered speaker. The XP106 will send a mix of all inputs, including Bluetooth audio. Each channel LEVEL will control corresponding output level to the LINE OUT jack. Linking Two XP106 Systems To use two XP106s as one system is simple. Just connect each side using a standard 44" Shielded instrument cable to the LINE OUT jack located on each XP106 rear panel. Both mixers and the microphones or instruments connected to each of the individual XP106 systems will be heard in both speakers. Auxiliary Line Input The LINE OUT jack can be used to accept any line level input source. This input does not have a level control, so you must utilize the output level of the connected device to control the level of the audio in the XP106. 20 SAMSON Making Connections MP3 Player, Portable Audio lal Microphone, Instrument*, Line Level Device Stage XPD1 Wireless System Instrument*, Keyboard, Drum Machine Paired Bluetooth Device LINE OUT
* An active preamp is needed in order to use acoustic instruments with the XP106. XP106 Portable PA System 21 XP106 Specifications LEVEL Power Output ........ Frequency Response... Mic/Instrument Input... Line Input... ...... Awe input sss ee eu eas Wireless Input... 2... Controls 2... 2... Tone Control. 2... 2... Line Input/Output... .. Bluetooth... .. 2... Speakers... ..-..... Built-in Battery... 2... Operation 4 a awe we ea as Battery Charging... ... AC/DC Adapter... .... Construction ........ Mounti WZ aa aim we a aw Operating Temperature... Dimensions (LXDXH) .... 22 100 watts 75 Hz to 15kHz +/-3dB XLR / %" combo connector yy"
IZ"
USB Mic/Inst, Line/Aux, Wireless, Blutooth Speech/Music switch
" TS Bluetooth 3.0, A2DP 6" Woofer + 1" HF Driver 12V / 8AH, Rechargeable & Sealed Up to 20 hours subject to operating conditions Approx. 4-8 hours for a single charge SMPS AC100~240V, 50~60H2/ DC18V-1.5A Polypropylene, internally ribbed Perforated Steel Grill, powder coated Integral 1 3/8-inch Pole Mount Receptacle
. 710C ~ +40C Ob" O" 14.2"
240 mm x 230 mm x 360 mm 16.3 Ib 7.4 kg Stage XPDI Specifications Simultaneous Systems... .. 2 Working Range... ...... 100! line of sight Working Frequency. ...... 2.404~2.476GHZ Modulation type... ..... GFSK Audio Frequency Response. 2OHZ- 16KHZ THD... ee ee <0.1% (at 1KHz, -10dBu) Signalto Noise... ...... >85 dB Operating Temperature... .. -10C ~ +40C Stage HXD1 Microphone Element. .... Q6 Dynamic RF Power... 2... ee <10 mW EIRP Power Requirements... .. Two AA (LR6) alkaline batteries Battery Life... 2... 2.2.04 20 hours Dimensions ........... 10.2" x 2.1"
260 mm x g54 mm Weight... 2... ee 0.5 Ib 218 Stage RXD1 Max. Analog Audio Output Level. OdBu Audio Output Impedance... 100 Kohms USB audio sample rate... 32 KHZ USB audio support... 2... Vista, Win7, Win8, Mac OSX without driver Operating Voltage ........ 5V DC Dimensions (LXDXH) ....... 3.5" %.0.9" X31"
89mm x 23 mm x 8mm Weights . 2 . sa a aie we a 4 0.35 oz 10g XP106 Portable PA System 23. Samson Technologies Corp. 45 Gilpin Avenue Hauppauge, New York 11788-8816 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 631-784-2201 www.samsontech.com