FCC ID: 2AGPP-SKWB8V3 SamKnows Whitebox 8.0+ with WiFi

Do not use the product in the environment at too high or too low temperature, never expose the product under strong sunshine or too wet environment. The suitable temperature for the product and accessories is 0-40. When charging, please place the product in an environment that has a normal room temperature and good ventilation. It is recommended to charge the product in an environment with a temperature that ranges from 0~40. Please ensure to use only the charger offered by the manufacturer. Using unauthorized charger may cause danger and violate the authorization of the product and the guarantee article. This charger is for indoor use only.The charger type is S24B73-120A200-0K, output voltage/current is 12Vdc/2A. The plug considered as disconnect device of adapter. If you use a third-party charger, the recommended output voltage/current of the adaptor is 12dc/2A.,and the adapter shall be CE approval type. RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body. Frequency bands WLAN 2.4GHz WLAN 5GHz Max EIRP (dBm) 19.51 21.15 This device is restricted to indoor use where operated in the European Community using frequency in 5150MHz-5350MHz to reduce the potential for interference. Manufacturer Manufacturer: SamKnows Limited Address: Hill House,1 Little New Street,London, EC4A 3TR,United Kingdom This product can be used across EU member states. EU Regulatory Conformance Hereby, SamKnows Limited Corporation declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Web site https://samknows.com/eu-certification Federal Communication Commission (FCC) Radiation Exposure Statement When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. RF exposure information: To maintain compliance with FCC RF exposure requirements, use the product that maintain a 20cm separation distance between the user's body and the host. MPE limit for RF exposure at prediction frequency is 1.0mW/cm2 for 2.4G&5G WiFi. The Max MPE for 5G WiFi is 0.112mW/cm2. It satisfy RF exposure compliance-

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-C-onsult the dealer or an experienced radio/TV technician for help. The device for operation in the band 5150-5350MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. FCC ID:2AGPP-SKWB8V3

Samknows Whitebox 8.0+

Model:SK-WB8+

DC:12V 272 2A S/N:YYMMXXXXX UA UNIV UH AU MAC:XXXXXXXXXXXX This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID:2AGPP-SKWB8V3 HVIN:AP-MSM001-0031 SamKnows Limited, 94 New Bond Street, London, W1S 18J Made in China

SamKnows Limited Date:2021-04-12 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 treatment of certain requests confidentiality and this application. The materials contain Re: Request of Confidentiality for FCC ID: 2AGPP-SKWB8V3 To Whom it may concern:

Pursuant to sections 0.457 and 0.459 of Commissions Rules(CFR 47), and Section 552(b)(4) of the Freedom of Information Act, SamKnows Limited hereby information trade secrets and accompanying proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA04-1705. This provision will give SamKnows Limited temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Short-Term Confidential exhibits are listed as follows:

PERMANENT AND SHORT-TERM CONFIDENTIAL LIST PERMANENT SHORT-TERM Exhibit 1 2 3 4 5 6 7 8 Description Block Diagram Operational Description Schematics BOM External Photos Internal Photos Test-Setup Photos User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Signatory:

Name: Neil Campbell Company name: SamKnows Limited Address: 94 New Bond Street, London W1S 1SJ, United Kingdom Tel: 020 3111 4330Email: neil@samknows.com

SamKnows Limited Date: 2021-04-12 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern:

The SamKnows Limited, the undersigned, hereby authorizes Miss. Wendy Zhan from Shenzhen Morlab Communications Technology Co., Ltd., to act on the behalf of the SamKnows Limited solely in matters relating to the application for an FCC equipment authorization for FCC ID: 2AGPP-SKWB8V3 including the signing of documents in connection with this Application. Necessary acts carried out Shenzhen Morlab Communications Technology Co., Ltd. on our behalf of the SamKnows Limited in connection with the Application shall have the same effect as acts of the SamKnows Limited. SamKnows Limited also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Thank you for your attention to this matter. Yours Sincerely, Signatory:

Contact name: Neil Campbell Title: Director Tel: 020 3111 4330 Email: neil@samknows.com Company name: SamKnows Limited

SamKnows Limited UNII Declaration Letter We have declared below featured for FCC equipment authorization, device FCC ID: 2AGPP-

SKWB8V3

(1) DFS Device --

Master, Client without radar detection capability, Client with Radar detection capability , N/A

(2) Active / Passive Scanning , adhoc mode access point capability Frequency Band

(MHz) Active Scanning

(the device can transmit a probe

(beacon)) 2412 2472 MHz 2422 2462 MHz 5745 5825 MHz 5755 5795 MHz 5180 5240 MHz 5190 5230 MHz 5260 5320 MHz 5270 5310 MHz 5500 5700 MHz Yes, 5510 5670 MHz Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, No No No No No No No No No No passive scanning

(where the device is can listen only with no probes) Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, No No No No No No No No No No Ad Hoc Mode capability Access point capability Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, No No No No No No No No No No Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, No No No No No No No No No No

(3) Country code selection ability -

If no, pls explain how was implemented : Country is selected as US by default and user can not change the country code.

(4) Meet 15.202 requirement -

pls check below :

Yes , Yes , No , No A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes can not be modified by end user or an installer. No Apply , Apply ,

(If apply , pls help to provide explanation on how it was implement (By hardware or software , and how software was controlled) The device configuration can not be modified by user as program is not exposed to user by any means. Hardware does not allow USB connection for user which is must to change the configuration. If you have any questions, please feel free to contact me at the address shown below. Yours sincerely, Signatory Printed Name : Neil Campbell Position:Director

SamKnows Limited Suppliers Declaration Of Conformity for the FCC SDoC Procedure The following Equipment adapt FCC SDoC Procedure according to FCC part 2.906 :

Product Name: SamKnows Whitebox 8.0+

Brand Name: SamKnows Model Number: SK-WB8+

Report Number: SZ20110143E01 Its herewith confirmed to comply with the requirements of FCC Part 15 Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. It is understood that each unit marketed is identical to the device as tested, and any changes to the device that could adversely affect the emission characteristics will require retest. The following importer / responsible party in United States:

Not Available at Certification Stage Company Name: N/A Company Address: N/A Telephone: N/A Fax: N/A Person is responsible for marking this declaration:

Neil Campbell Director ____________________________________ ______________________________________ Name (Full name) ____________________________________ ______________________________________ Legal Signature Date 2021-04-12