ITM-G3 OEM/Integrators Installation Manual Confidential Information Samsung Electronics Co., Ltd. Rev. 1.0 2023. 5. 08 IoT Modul IoT Module ITM-G3 SLP-I211BZXXWW Key Features ZigBee 3.0 and BLE 5.0 4-GPIO channel outputs for Switch control Basic Features Series. Part Number Input Output Connectivity Frequency TX Power ITM-Gen3 SLP-I211BZXXWW 3.3Vdc GPIO ZigBee, BLE 2.4GHz 8dBm Firmware Version : TBD 1. Specification Article Symbol Unit Note Min. Typ. Max. Specification Electrical SPECIFICATIONS Input Voltage Input Current ENVIRONMENTAL SPECIFICATIONS Operation Temperature Storage Temperature MECHANICAL SPECIFICATION 3.0 3.3 Vin mA
-40
-50 V mA C 3.8 100 85 150 Dimensions 18.5 x 10.5 x 2.2 mm L x W x H 2. Pin Assignment Pin No. 1 / 2 / 10 / 14 / 15 / 17 / 18 / 26 3 4 5 6 7 8 9 Name GND GPIO1
GPIO2 GPIO3 GPIO4 Function Ground Light on/Dim up
Light off/Dim down Status LED LED toggle 11 12 13 16 19 20 21 22 23 24 25 3. Dimension Reset
Vin
Software Reset
Input Voltage
4. Application Guide Solder PAD Solder spread area Solder pad shoud be soldered over 60% of full area. Clearance Area Recommend to design a clearance area in the main board for the better performance of antenna radiation. It should be applied to all layers of the board. There shall not be any components, traces, pads or copper areas in any layer within the clearance area. Minimum clearance area size (non-copper) = 10.5mm x 4.0mm Reflow Profile Max. Temperature: 245C Max. number of reflow cycles: 2 Hand soldering: follow IPC recommendation 5. Label QR Code FCC ID QR Code Information:
SLP-I211BZXXWW_210928_AAAAAAAA_BBBBBBBB_CCCCCCCC Index Product Code Date BT MAC Address ZigBee EUI Install Code Under-Bar Total Digit Contents SLP-I126BZXXUS YYMMDD AAAAAAAA1) BBBBBBBB2) CCCCCCCC3) _ Digit 14 6 12 16 36 4 88 6. FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions:
(1) This Device may not cause harmful interface, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. FCC RF Radiation Exposure Statement
(1) This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
(2) This equipment complies with RF radiation exposure of 20cm between the radiator and your body. WARNING 1. Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. It is necessary to check whether the product using the module meets the certification. 2. 3. Exposure in the finished product should be re-evaluated. CAUTION: Exposure to Radio Frequency Radiation. Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit. 7. Precaution To prevent the module from any defect, please handle and store it with care Do not drop or give shock Do not store in very humid location or at extreme temperature Do not open or disassemble the product Static electricity or surge voltage may damage the components inside the module, as such please observe proper anti-
electrostatic working process People handing the module should be well grounded (e.g. using ESD wrist band) and wear anti-static working clothes and gloves All related devices and instruments in the production line should be well grounded (e.g. working table, measuring equipment, assembly jigs) Avoid input voltage exceeds the maximum rating, which will cause damage to the circuit and result in malfunction. Specifications are subject to change without notice. RF exposure considerations This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. RF Exposure - This device is only authorized for use in a mobile application. At least 20 cm of separation distance between the module and the user's body must be maintained at all times. Instruction to Integrator Labelling A label must be affixed to the outside of final commercial product with the following statements:
This device contains FCC ID: 2AR3A-ITM-G3 RF exposure considerations Consistent with 2.909(a), the following text must be included within the users manual or operator instruction guide for the final commercial product This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device is only authorized for use in a mobile application. At least 20 cm of separation distance between the module and the user's body must be maintained at all times. Additional testing, Part 15 Subpart B disclaimer The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. The commercial applicable. Statement included product manual shall final user Part FCC the be 15 of in if Caution Statement for Modifications:
CAUTION: Any changes or modifications not expressly approved could void the users authority to operate the equipment. Legal and additional information. CONFIDENTIAL About Samsung Electronics Co., Ltd. Samsung Electronics Co., Ltd. inspires the world and shapes the future with transformative ideas and technologies. The company is redefining the worlds of TVs, smartphones, wearable devices, tablets, cameras, digital appliances, medical equipment, network systems, and semiconductor and LED solutions. For the latest news, please visit the Samsung Newsroom at news.samsung.com. Copyright 2019 Samsung Electronics Co., Ltd. All rights reserved. Samsung Electronics reserves the right to modify, at its sole discretion, the design, packaging, specifications, and features shown herein without notice at any time. Samsung Electronics Co., Ltd. 95, Samsung 2-ro, Giheung-gu Yongin-si, Gyeonggi-do, 446-711 KOREA www.samsungled.com