Dell 5002 Datasheet REV 0.1 Samsung Electronics Summary This datasheet presents the general performance and specifications of Dell 5002 IEEE 802.11b/g WLAN CARD using SWL-2900U. ML-NWA30L Dell 5002 is the low power USB interface card for 802.11b/g wireless LAN aimed at embedded application. Dell 5002 is the USB interface card that adopts a single-chip wireless LAN MAC(medium-access controller) spread-spectrum baseband processor and 2.4GHz RF radio. Dell 5002 supports IEEE 802.11b and 802.11g standards. Data rate up to 54MHz can be provided in 802.11g mode of operation. The main IC of Dell 5002 includes an 80MHz ARM7 core, 384KB of on-chip SRAM, and 80KB of on-chip ROM. Dell 5002 is able to host the entire WLAN driver and TCP/IP stack on-chip. This minimizes development time, cost, and burden on the host processor resources making Dell 5002 an ideal WLAN solution for emdedded application. Dell 5002 provides crucial power management functionality and requires only a single 5.0V supply voltage. Figure 1-1 Dell 5002 1.3 Block Diagram Figure 1-2 Dell 5002 Block Diagram W x L x H = 51mm x 108mm x 18mm Figure 2-1 Dell 5002 Mechanical Dimension Figure 2-2 Dell 5002 Picture Host Interface : Molex 5084616-1, 40pin, Straight, SMT
* SIZE : 6.5 x 21.5 x 11.5 mm pin #21 pin #40 pin #1 pin #20 Figure 2-3 Dell 5002 CN1 Connector PIN Assignment Table 2-1 CN1 PIN Description
+35 In the case of measurement with Case, Antenna specificaiton is like below. 0.1 2008.02.18 First released FCC Compliance
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and this device must accept any
(2) interference including interference that may cause undesired operation. received,
Caution Any changes or modifications NOT by Samsung explicitly APPROVED Electronics Co., Ltd. could cause the DELL5002 module to cease to comply with FCC rules part 15, and thus void the user's authority to operate the equipment. information
RF-exposure statement These modular transmitters, Dell5002, comply with FCC radiation exposure limits set forth for an uncontrolled environment. The Dell5002 should be installed and operated with minimum distance 20cm between the antenna and the body of the user or nearby persons. The OEM integrator has to be aware not to provide the end user regarding how to install or remove this RF module in the users manual of the end product which integrate this module. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. to for testing transmitter responsible As long as the 2 conditions above are met, further testing will not be required. However, the OEM integrator is still their end product for any additional compliance requirements required with this module installed
(for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met
(for example certain laptop configurations or co-location with another transmitter), then the FCC authorization longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible the end product (including the transmitter) and obtaining a separate FCC authorization. re-evaluating is no for
Antenna These modular transmitters are for OEM integrations only. The end-user product will be installed in such a manner that only the authorized antennas are used.
Label and manual requirements for the End Product This device contains FCC ID: A3LDELL5002 For an end product using the Dell5002 there must be a label containing, at least, the following information:
FCC ID for model Dell5002 The label must be affixed on an exterior surface of the end product such that it will be visible upon inspection in compliance with the modular approval guidelines developed by the FCC. this device may not cause harmful Where the Dell5002 will be installed in final products larger than 8cm x 10cm following statements has to be placed ONTO the device.
"This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation."
In case where the final product will be installed the end-
consumer is not able to see the FCC ID and/or this statement, the FCC ID and the statement shall also be included in the end-product manual. The users manual for end users must include in a prominent location "IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter."
locations where the antenna used information following the for in EU Compliance only. for OEM
Regulatory compliance of the Dell5002 The Dell5002 are made integrations The regulations applying to the Dell5002 is the R&TTE Directive 1999/5/EC. Dell5002 requirements of the R&TTE Directive. following meets the European R&TTE Directive article Article 3.1(a) Test category Harmonized standard Protection health and safety of EN 60950-1, EN 50385 Article 3.1(b) EMC EN 301 489-1/-17 Article 3.2 Effective use of the spectrum EN 300 328 The conformity assessment Dell5002 were completed in accordance with IV procedures, and the EC Declaration of Conformity is attached to this manual. the R&TTE Directive Annex the for
Cautions regarding regulatory compliance when integrating the Dell5002 integrating the Dell5002 The person becomes the manufacturer of the final product and is therefore responsible for demonstrating compliance of the product with the essential requirements of the R&TTE Directive. final In all cases assessment of the the product must be made against Essential requirements of the R&TTE Directive Article 3.1(a) and (b), safety and EMC respectively, and any relevant Article 3.3 requirements This device is intended only for OEM integrators under the following conditions:
1. This appliance and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. 2. A minimum separation distance of 20 cm must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements of the Council recommendation 1999/519/EC of 12 July 1999. As long as the 2 conditions above are met, no further evaluation under Article 3.2 of the R&TTE Directive and do not require further involvement of an R&TTE Directive Notified Body for the final product. In all other cases, or if the manufacturer of the final product the equipment integrating the radio module must be assessed against Article 3.2 of the R&TTE Directive. Please note that this product, Dell5002, uses not harmonized throughout the Community. This product is classified as Class 2 radio equipment for which some Member States apply restrictions on placing on the market and in use. Any parties putting Class 2 radio equipment on the market must notify the spectrum management authority of their intention, and the radio equipment must be given a Class Identifier (alert symbol). frequency in doubt relevant national bands radio then is
Antenna This product, Dell5002, integrations only. The end-user product will be installed in such a manner that only the authorized antennas are used. for OEM is
Enclosure This product, Dell5002, is made for integrating in another final product. For this reason, there are some parts of the final product on which the Dell5002 depends regarding EMC and safety. The Dell5002 is mounted on the circuit board of the final product, and must be contained inside the case of the final product. Integrated the Dell5002 in the final product so that its surfaces are not in contact with the outside. compliance regulatory for
Documentation In the documentation for the conformity assessment of the final product, state clearly that the Dell5002 is integrated in the system.
Conformity Assessment of the Products integrating the Dell5002 a following is in the conformity integrating The supplementary explanation of conformity assessments for final products radio modules such as the Dell5002, that have passed assessments accordance with the R&TTE Directive. The procedures for conformity assessment in accordance with the R&TTE Directive are the responsibility of the manufacturer of the final product. With final products integrating radio modules, the person who integrates the system becomes the manufacturer of the final product, and it is their responsibility to certify that the requirements of the R&TTE Directive and met. the module in
Exemption from conformity assessment However, if radio modules that meet the requirements of the R&TTE Directive and that conformity final in a assessment are the integrated passed have the the that from follows product cautions concerning integrating radio modules, they are exempted conformity assessment for R&TTE Directive Article 3.2 (efficient use of the radio spectrum). For details, refer to the following Guidance and ETSI Technical Report the R&TTE Compliance Association, and check whether your case applies. from Organization R&TTE Compliance Association Document TGN 01 Rev 3 No. Note Guidance Technical on Requirement for a Final Product that Integrates an R&TTE Directive Assessed Module You can download the guidance from the download area of R&TTE Compliance association. http://www.rtteca.com Document title URL Organization
(Technical ETSI report) Document No. ETSI TR 102 070-2 Document title URL Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide to the application of harmonized standards to multi-radio and combined radio and non-
radio equipment; Part 2: Effective use of radio frequency spectrum You can download the guidance from the ETSI web site by entering TR102 070-2 the search engine. Before downloading, you will be requested to register. in http://www.rtteca.com
Conformity assessment procedures for final products exempted from R&TTE Directive Article 3.2 In every case, the manufacturer of a final product must follow the procedures for conformity assessment of the final product with the requirements of R&TTE Directive or authorities organizations of the relevant countries. official certification radio module and Article 3.1(a) and (b), for safety and EMC. The conformity assessment for Article 3.2 is carried out in accordance with the following:
1) Attach the EN 300 328 test report of the assessed the EC Declaration of Conformity to the conformity assessment of final product (The Declaration of Conformity is attached to the manual). 2) Specify on the conformity assessment of the end product that the assessed radio module was the system without any changes, in accordance with the the manufacturer. installation integrated directions the of in radio bands frequency
Notification of the final product Please note that this product, Dell5002, uses not harmonized throughout the Community. The notification required by R&TTE Directive Article 6(4) is necessary. It is the responsibility of the manufacturer of the final product to notify the relevant national spectrum management authority of the intention to place the final product on the market.
CE marking to indicate final product It is necessary to attach the CE mark to the it conforms with all the directives that apply to the final product. It must be given a Class Identifier (alert symbol) in addition to the CE mark. that
Exemption clause Samsung Electronics Co., Ltd. does not guarantee the accuracy of the information above. In case of doubt or uncertainty, we the recommend that you check with Manufacturer Samsung Electronics Co., Ltd.
#259, Gongdan-Dong, Gumi-City Gyungbuk, Korea 730-030
(Sang youp Hyoun) / 17th ,January ,2008 EC Declaration of Conformity We, Samsung Electronics Co., Ltd. of Samsung Electronics Co., Ltd.
#259, Gongdan-Dong, Gumi-City, Gyeongsangbuk-Do, 730-030 Korea of Samsung Electronics(Shandong) Digital Printing Co., Ltd. 264209, Samsung Road, Weihai Hi-Tech IDZ, Shandong Province, China declare under our sole responsibility that the product WLAN Module model " Dell5002 "
to which this declaration relates is in conformity with R&TTE Directive 1999/5/EC By application of the following standards Article 3.1(a) Article 3.1(a) Article 3.1(b) EN 60950-1:2001 EN 50385:2002 Health Safety EMC Article 3.2 Radio Notified Body Documentary conformity UL Apex Co., Ltd. 4383-326, Asama-cho, Ise-shi, Mie 516-0021, JAPAN EU Identification Number: 1731 evidence to demonstrate Description Report or Certificate No. Issue Date Issued by Health Safety EMC Radio Declaration of Conformity issued by Samsung Electronics Co., Ltd. SK Tech Co., LTD. SK Tech Co., LTD. SK Tech Co., LTD. EN 301 489-1 V1.7.1(2006-10), EN 301 489-17 V1.2.1(2002-08) EN 300 328 V1.7.1 (2006-10)