MB8811QAN Bluetooth Module user manual

 

Bluetooth Module : MB8811QAN

[top] [bottom]

This MB8811QAN Module is compatible with Bluetooth specification version 4.2. MB8811QAN is a fully integrated RF, baseband controller etc. SPECIFICATION Main Chips Standards CSR8811A12 Bluetooth 4.2 Frequency Band 2402 ~ 2480 MHz Tx Power Rx Sensitivity Distance Power Voltage Dimension Environmental Range 0.25 ~ 10mW (Bluetooth Power Class 1)

< -70dBm (BER 0.1%)

< 10m (open space) 3.3V 18.631.2 3.4 mm Operation temperature : -25 ~ +70 Modulation mode GFSK, 8DPSK Communication method FHSS Pin define(TOP PIN MAP) No 1 2 3 4 5 6 7 8 9 10 Pin Name I/O Description VDD RESET RTS CTS TX GND RX GND SCL SDA I I O I O

-

I

-

O I/O Positive Input for the internal regulator (3.0 ~ 3.6V) Reset if low. Input debounced so must be low for >5ms to cause a reset Bluetooth UART Request to Send. Active-low request. Bluetooth UART Clear to Send.Active-low clear. Bluetooth UART Serial Output. Ground. Bluetooth UART Serial Input. Ground. I2C interface Clock I2C interface DATA 1. VDD 2.RESET 3.RTS 4.CTS 5.TX 6.GND 7.RX 8.GND 9.SCL 10.SDA Dimension TOP View Mark Dimension Mark Dimension Mark Dimension A B C 31.600.3 18.600.3 8.00.2 D E F 2.600.2 2.00.2 1.80.2 G 1.00.2

(Unit : mm) Electrical Characteristics Conditions : VDD = 3.3V, Ta = 25 , unless otherwise noted. Absolute Maximum Ratings Parameter Power Supply Voltage : VDD Storage Temperature Recommended Operating Conditions Parameter Power Supply Voltage Operation Temperature Current consumption Parameter Page scan, Time interval = 1.28s Inquiry and Page scan, Time interval = 1.28s ACL No data transfer ACL data transfer Input/Output Characteristics Parameter VIL Input Voltage Low VIH Input Voltage High VOL Output Voltage Low VOH Output Voltage High Min

-0.4V

-40 Max 3.6V 85 Unit DCV Min 3.0V

-25 Max 3.6V 70 Unit DCV Connection Type Avg Peak Unit

-

-

Master Master 2 2 10 32 3 mA mA mA mA Min

-0.4 Max 0.8 0.7*VDD VDD+0.4

-

VDD-0.2 0.2

-

Unit V V V V General Performance Parameter Frequency Range Transmitter Performance Condition Normal Min 2402 Typ Max Unit

-

2480 MHz Parameter Condition Min Typ Max Unit Transmit Power Power density 20dB bandwidth Adjacent channel power

(F0 = 2441MHz) Out-band Spurious Emission Modulation Characteristic Initial Carrier Frequency Tolerance Carrier Frequency Drift Receiver Performance Normal Normal Normal F=F0 2MHz F=F0 3MHz F=F0 4MHz 30MHz ~ 1GHz 1GHz ~ 12.75GHz 1.8GHz ~ 1.9GHz 5.1GHz ~ 5.3GHz F1avg F2max F2avg / F1avg DH1 packet DH5 packet

-6 0

-

-

-

-

-

-

-

-

140 115 80

-75

-25

-

-

-

-

-

-

-

-

-

-

-

-

8 20 1000

-20

-40

-40

-36

-30

-47

-47 175

-

-

75 25 dBm dBm KHz dBm dBm dBm dBm dBm dBm dBm KHz KHz

%

KHz KHz Parameter Condition Min Type Max Unit Sensitivity at 0.1% BER Sensitivity at 0.1% BER Maximum received signal at 0.1% BER Maximum level of intermodulation interferers Single slot (DH1 packet) Multi slot (DH5 packet) f1-f2 = 5 MHz, Pwanted= -64 dBm

-

-

-20

-39

-

-

-

-

-70

-70

-

-

dBm dBm dBm dBm Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &

your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE:

20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. IC Statement This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. MB8811QAN Test Manual 1) RF Test Utility 2) First time, CSR Bluesuite program must be installed. you can use BTCli.exe and enter DUT(Device Under Test) mode. So RF equipment can inquiry and test. (reference document.)

* reference document : MB8811QA_JIG_DUT_BLE_MANUAL.pdf 3) RF Test method RF Test tool is BlueTest.exe at CSR bluesuite program. You can see detail explanation from reference document.

* reference document : BlueTest Instruction Manual.pdf Conformity Assessment Display Company name: Samsung Electronics Model : Specific micro-power wireless devices (wireless data communication system devices)

(MB8811QAN) Manufacture Year : 2019. Manufacturer / Manufacture Country : Samsung Electronics / Korea