SIP005AFS30 ARTIK-0530 User Manual 20161006 v2 - 06 SIP007AFS00 manual final

MODULE DISCLOSURES QUICK START GUIDE FCC REGULATORY DISCLOSURES This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/ TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the transmitters radiating structure(s) and the body of the user or nearby persons. This module is intended for OEM integration. The OEM integrator is responsible for FCC compliance and compliance with all applicable regulations including those for modular transmitters 47 C.F.R. 15.212. The OEM product must comply with all applicable labeling requirements including those contained in 15 C.F.R. 15.19. The OEM is solely responsible for certification and testing and labeling of its own products. In addition to any independently required labels, the OEM shall also affix to the outside of a device into which the module is installed a label referring to the enclosed module. This exterior label should be prepared in a legible font and permanently affixed and using the wording Contains Transmitter Module FCCID: A3LSIP005AFS30 The OEM is required to ensure that the end product integrates this module so as to maintain a minimum distance of 20 cm between the equipments radiating structure(s) and the body of the user or nearby persons. The OEM shall also advise its end user of this requirement as required by applicable rules. The OEM shall require that the end user of its product be informed that the FCC radio frequency exposure guidelines for an uncontrolled environment can be satisfied. The OEM shall further inform its DB2/ 30119155.1 DRAFT 04/12/16 5:16PM 4:05PM end user that any change or modifications to this module not expressly approved by the manufacturer will void the warranty and the users authority to operate the equipment. INDUSTRY CANADA REGULATORY DISCLOSURES INDUSTRY CANADA STATEMENT This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opration est soumise aux deux conditions suivantes:(1) cet appareil ne peut causer d'interfrences, et

(2) cet appareil doit accepter toute interfrence, y compris les interfrences qui peuvent causer un mauvais fonctionnement de l'appareil. INDUSTRY CANADA RADIATION EXPOSURE STATEMENT AND LIMITATIONS ON USE This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This equipment should be installed and must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment is restricted to indoor use in the 5.15-5.25 GHz range. This equipment is not able to be operated at 5600-5650. In the United States and Canada, only Channel 1~11 can be operated and these channel assignments deal only with the 2.4 GHz range. The end product must be labeled to display the Industry Canada certification number of the module. Contains transmitter module IC: 649E-SIP005AFS30 Le dispositif d'accueil doivent tre tiquets pour afficher le numro de certification d'Industrie Canada du module. Contient module metteur IC : 649E-SIP005AFS30 DB2/ 30119155.1 DRAFT 04/12/16 5:16PM 4:05PM EU REGULATORY DISCLOSURES CE STATEMENT *

The following statement must be supplied with each product but can be printed in the user manual, the packaging, or provided as a separated leaflet. Hereby, Samsung declares that this IoT Module is in compliance with the essential requirements and other relevant provisions of Article 3 of the R&TTE Directive 1999/5/EC, 2004/108/EC and RoHS directive 2011/65/EU. The declaration of conformity may be consulted at [www.artik.io/]

DB2/ 30119155.1 DRAFT 04/12/16 5:16PM 4:05PM