FCC ID: A3LSP10BT Notebook PC w/ Bluetooth

Notices No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical photocopying, recording or otherwise, without the prior written permission of the manufacturer. The information within this manual is subject to change without notice. The manufacturer shall not be held liable for technical or editorial errors or omissions contained in herein; nor for incidental or consequential damages resulting from the furnishing, performance or use of this material. Microsoft Windows is a registered trademark of the Microsoft Corporation. Product names mentioned herein are for identification purposes only, and may be trademarks and/or registered trademarks of their respective companies. Macrovision Statement If your computer has a DVD drive and an analog TV Out port, the following paragraph applies:

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. Copyright 2002 All rights are reserved Notices i Important Safety Information Safety Instructions Your system is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that the safety instructions marked on the product and in the documentation are followed. NEe, Always follow these instructions to help guard against personal injury and eS damage fo your system. Hy Setting Up your System Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. Do not use this product near water or a heat source such as a radiator. Set up the system on a stable work surface. The product should be operated only with the type of power source indicated on the rating label. Ensure that the electrical outlet you are using to power your equipment is easily accessible in case of fire or short circuit. If your computer has a voltage selector switch, make sure that the switch is in the proper position for your area. Openings in the computer case are provided for ventilation. Do not block or cover these openings. Make sure you provide adequate space, at least 6 inches

(15 cm), around the system for ventilation when you set up your work area. Never insert objects of any kind into the computer ventilation openings. Ensure that the fan vents on the bottom of the casing are clear at all times. Do not place the computer on a soft surface, doing so will block the bottom vents. If you use an extension cord with this system, make sure that the total ampere rating on the products plugged into the extension cord does not exceed the extension cord ampere rating. fi Users Manual Care During Use Do not walk on the power cord or allow anything to rest on it. Do not spill anything on the system. The best way to avoid spills is to not eat or drink near your system. Some products have a replaceable CMOS battery on the system board. There is a danger of explosion if the CMOS battery is replaced incorrectly. Replace the battery with the same or equivalent type recommended by the manufacturer. Dispose of batteries according to the manufacturers instructions. If the CMOS battery requires replacement insure that a qualified technician performs the task When the computer is turned off, a small amount of electrical current still flows through the computer. To avoid electrical shock, always unplug all power cables, remove the battery and modem cables from the wall outlets before cleaning the system. Unplug the system from the wall outlet and refer servicing to qualified personnel if:

The power cord or plug is damaged. Liquid has been spilled into the system.

~ The system does not operate properly when the operating instructions are followed.

~ The system was dropped or the casing is damaged. The system performance changes. Replacement Parts and Accessories Use only replacement parts and accessories recommended by manufacturer. To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord. Do not use this product in areas classified as hazardous. Such areas include patient care areas of medical and dental facilities, oxygen rich environments, or industrial areas. Important Safety Information iii Battery Disposal

"ty, Do not put rechargeable batteries or products powered by non-removable eS rechargeable batteries in the garbage. H Contact the Samsung Helpline for information on how to dispose of batteries that you cannot use or recharge any longer. Follow all local regulations when disposing of old batteries. iv Users Manual Regulatory Compliance Statements Wireless Guidance Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook system. The following section is a general overview of considerations while operating a wireless device. Additional limitations, cautions, and concerns for specific countries are listed in the specific country sections (or country group sections). The wireless devices in your system are only qualified for use in the countries identified by the Radio Approval Marks on the system rating label. If the country you will be using the wireless device in, is not listed, please contact your local Radio Approval agency for requirements. Wireless devices are closely regulated and use may not be allowed. The power output of the wireless device or devices that may be embedded in your notebook is well below the RF exposure limits as known at this time. Because the wireless devices (which may be embedded into your notebook) emit less energy than is allowed in radio frequency safety standards and recommendations, manufacturer believes these devices are safe for use. Regardless of the power levels, care should be taken to minimize human contact during normal operation. As a general guideline, a separation of 20 cm (8 inches) between the wireless device and the body, for use of a wireless device near the body (this does not include extremities) is typical. This device should be used more than 20 cm (8 inches) from the body when wireless devices are on and transmitting. This transmitter must not be collocated or operation in conjunction with any other antenna or transmitter. Some circumstances require restrictions on wireless devices. Examples of common restrictions are listed below:

xty,| Radio frequency wireless communication can interfere with equipment on Eis commercial aircraft. Current aviation regulations require wireless devices to be J turned off while traveling in an airplane. 802.11B (also known as wireless Ethernet or Wifi) and Bluetooth communication devices are examples of devices that provide wireless communication. Regulatory Compliance Statements v vi Users Manual In environments where the risk of interference to other devices or services is harmful or perceived as harmful, the option to use a wireless device may be restricted or eliminated. Airports, Hospitals, and Oxygen or flammable gas laden atmospheres are limited examples where use of wireless devices may be restricted or eliminated. When in environments where you are uncertain of the sanction to use wireless devices, ask the applicable authority for authorization prior to use or turning on the wireless device. Every country has different restrictions on the use of wireless devices. Since your system is equipped with a wireless device, when traveling between countries with your system, check with the local Radio Approval authorities prior to any move or trip for any restrictions on the use of a wireless device in the destination country. If your system came equipped with an internal embedded wireless device, do not operate the wireless device unless all covers and shields are in place and the system is fully assembled. Wireless devices are not user serviceable. Do not modify them in any way. Modification to a wireless device will void the authorization to use it. Please contact manufacturer for service. Only use drivers approved for the country in which the device will be used. See the manufacturer System Restoration Kit, or contact manufacturer Technical Support for additional information. United States of America Federal Communications Commission (FCC) Intentional emitter per FCC Part 15 Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook system. This section is only applicable if these devices are present. Refer to the system label to verify the presence of wireless devices. Wireless devices that may be in your system are only qualified for use in the United States of America if an FCC ID number is on the system label. The FCC has set a general guideline of 20 cm (8 inches) separation between the device and the body, for use of a wireless device near the body (this does not include extremities). This device should be used more than 20 cm (8 inches) from the body when wireless devices are on. The power output of the wireless device (or devices), which may be embedded in your notebook, is well below the RF exposure limits as set by the FCC, This transmitter must not be collocated or operation in conjunction with any other antenna or transmitter. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. ne Wireless devices are not user serviceable. Do not modify them in any way. aS Modification to a wireless device will void the authorization to use it. Contact manufacturer for service. FCC Statement for Wireless LAN use:

While installing and operating this transmitter and antenna combination the radio frequency exposure limit of 1mW/cm2 may be exceeded at distances close to the antenna installed. Therefore, the user must maintain a minimum distance of 20cm from the antenna at all times. This device can not be colocated with another transmitter and transmitting antenna. Unintentional Emitter per FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Regulatory Compliance Statements vii This equipment has been tested and found to comply with the limits fora Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

e Reorient or relocate the receiving antenna. e Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet helpful:

Something About Interference. This is available at FCC local regional offices. Our company is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by our company. The correction will be the responsibility of the user. Use only shielded data cables with this system. Federal Communications Commission Part 68 Statement This equipment compiles with part of the FCC rules. On the back of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. This equipment uses the following USOC jacks : RJ11C An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or promises wiring using a compatible modular jack which is Part 68 compliant. See Installation Instructions for details. viii Users Manual The REN is used to determine the quantity of devices which may be connected to telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by total RENs, contact the local telephone company to determine the maximum REN for the calling area. If the terminal equipment causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required, But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advanced notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment (Modem) for repair or warranty information, please contact your local distributor. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. The user must use the accessories and cables supplied by the manufacturer to get optimum performance from the product. No repairs may be done by the customer. This equipment cannot be used on public coin phone service provided by the telephone company. Connection to party line service is subject to state tariffs. The Telephone Consumer Protection Act of 199] makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be any number for which charges exceed local or long-distance transmission charges.) In order to program this information into your fax machine, refer to your communications software user manual. Regulatory Compliance Statements ix Canada Industry Canada (IC) Intentional Emitter per RSS 210 Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook system. This section is only applicable if these devices are present. Refer to the system label to verify the presence of wireless devices. Wireless devices that may be in your system are only qualified for use in Canada if an Industry Canada ID number is on the system label. As a general guideline, a separation of 20 cm (8 inches) between the wireless device and the body, for use of a wireless device near the body (this does not include extremities) is typical. This device should be used more than 20 cm (8 inches) from the body when wireless devices are on. The power output of the wireless device (or devices), which may be embedded in your notebook, is well below the RF exposure limits as set by Industry Canada. This transmitter must not be collocated or operation in conjunction with any other antenna or transmitter. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Ey Co prevent radio interference to licensed service, this device is intended to be iS operated indoors and away from windows to provide maximum shielding. i. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Ny, | Wireless devices are not user serviceable. Do not modify them in any way. aS Modification to a wireless device will void the authorization to use it. Contact Fo . manufacturer for service. Unintentional Emitter per ICES-003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada. Le prsent appareil numrique nmet pas de bruits radiolectriques dpassant les limitesapplicables aux appareils numriques de Classe B prescrites dans le rglement sur le brouillage radiolectrique dict par Industrie Canada. x Users Manual European Union The following information is only applicable to systems labeled with the CE mark C. European Directives This Information Technology Equipment has been tested and found to comply with the following European directives:

EMC Directive 89/336/EEC with amending directives 92/31/EEC & 93/68/

EEC as per EN 55022 Class B EN 61000-3-2 EN 61000-3-3 EN 55024 Low Voltage Directive (Safety) 73/23/EEC as per EN 60950(A1/A2/A3/A4/

All) Radio and Telecom Terminal Equipment Directive 199/5/EC as per CTR21 (if fitted with a modem device) ETS 300 328 (if fitted with a 2.4 GHz band embedded wireless device) ETS 301 489-1 (if fitted with a 2.4 GHz band embedded wireless device)

~ ETS 301 489-17 (if fitted with a 2.4 GHz band embedded wireless device) European Radio Approval Information

(for products fitted with EU-approved radio devices) This Product is a Notebook computer; low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz band, may be present (embedded) in your notebook system which is intended for home or office use. This section is only applicable if these devices are present. Refer to the system label to verify the presence of wireless devices. Wireless devices that may be in your system are only qualified for use in the European Union or associated areas if a CE mark C with a Notified Body Registration Number and the Alert Symbol is on the system label. The power output of the wireless device or devices that may be embedded in you notebook is well below the RF exposure limits as set by the European Commission through the R&TTE directive. Regulatory Compliance Statements xi European States qualified under wireless approvals:

EU Austria, Belgium, Denmark, Finland, France (with frequency restrictions), Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden and the United Kingdom. Accept EU _ Iceland, Liechtenstein, Norway and Switzerland European States with restrictions on use:

EU In France, the frequency range is restricted to 2446.5-2483.5 MHz for devices above 10 mW transmitting power such as wireless LAN. Accept EU No limitations at this time. European Telecommunication Information

(for products fitted with EU-approved modems) Marking by the symbol C indicates compliance of this equipment to the Radio and Telecom Terminal Equipment Directive 1999/5/EC. Such marking is indicative that this equipment meets or exceeds the following technical standards:

CTR 21 Attachment requirements for pan-European approval for connection to the analogue Public Switched Telephone Networks (PSTNs) of TE (excluding TE supporting voice telephony services) in which network addressing, if provided, is by means of Dual Tone Multi-Frequency (DTMF) signaling. a Although this equipment can use either loop disconnect (pulse) or DTMF ES (tone) signaling, only the performance of the DTMF signaling is subject to

- regulatory requirements for correct operation. It is therefore strongly recommended that the equipment is set to use DTMF signaling for access to public or private emergency services. DTMF signaling also provides faster call setup. This equipment has been approved to Council Decision 98/482/EECCTR 21 for Pan-European single terminal connection to the Public Switched Telephone Network

(PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN termination point. In the event of problems, you should contact manufacturer Technical Support. xii Users Manual Japan Wireless Devices Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook system. This section is only applicable if these devices are present. Refer to the system label to verify the presence of wireless devices. Wireless devices that may be in your system are only qualified for use in Japan if a TELEC ID is on the system label. Operational guidelines for 2.4 GHz band wireless equipment (if equipped) This equipment uses the 2.4 GHz ISM frequency band. The ISM band is the industrial, scientific, and medical device band. Devices that might also use this band are microwave ovens, other LAN devices, amateur radio stations, licensed premises radio stations, and non-licensed specified low-power radio stations. Prior to setting up your device:

1. Make sure that there are no other devices in your area using the same frequency band. 2. Change the channel, location, or discontinue device use if you are interfering with any other radio station. 3. Contact manufacturer if you have any problems with this device. LOBBORA LORE COMMORAR RR. SCT, CORR CERT LV OBORE - Ate - at ARKO, HOMBRE, CMORMS 1S SCEASATHSRRERT SBR SRRRORARDS. REM LGUREIMARBR, FR Fa PRR UE Pb OPRR) CHT) MEARS TORT, 1 COMMERAT EE. <BR HORA SA CIES OEE Xo 2 F-, COMBE (HORM) LOMICERTRMBRE LEMSICK, BP wics OBVORAE St CEROBKORL) ELTKE. ;

3. FRR, TOMSBYOCEMBAEE Bit, COMBE ERMC oT WEF CHMVAHE SHS, 24084 CORR ?, ACHR. DSSS RAL LC we BY, SFPRMSHMOtT. Regulatory Compliance Statements xiii VCCI Statement This equipment is in the Class B category Information Technology Equipment to be used in a residential area or an adjacent area thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Information Technology Equipment aimed at preventing radio interference in such residential areas. When used near a radio or TV receiver, it may become the cause of radio interference. Read instructions for correct handling. Sees OUT }

CORES, SRUBRSSRRMSS Tee (VCC |) Ome CB3< 7SABRRRRECT, (ORM. REACT Sce BSHCULTHNIERTR CORMMSUAVTUEY 3 ASHER T BHANSEC. SERBASSHCTCCOMAOST, PROB MIC > TIELLIRO REEL T FAL. xiv Users Manual Laser Safety All systems equipped with CD or DVD drives comply with the appropriate safety standards, including IEC 825. The laser devices in these components are classified as Class 1 Laser Products under a US Department of Health and Human Services

(DHHS) Radiation Performance Standard. Should the unit ever need servicing, contact an authorized service location.

; Ate, | Laser Safety Note:

Eis Use of controls or adjustments or performance of procedures other than those ae = specified in this manual may result in hazardous radiation exposure. To prevent exposure to laser beams, do not try to open the enclosure of a CD or DVD drive. Laser Safety xv Power Cord Requirements The power cord set (wall plug, cable and AC adapter plug) you received with your computer meets the requirements for use in the country where you purchased your equipment. Power cord sets for use in other countries must meet the requirements of the country where you use the computer. For more information on power cord set requirements, contact your authorized dealer, reseller, or service provider. General Requirements The requirements listed below are applicable to all countries:

@ The length of the power cord set must be at least 6.00 feet (1.8m) and a maximum of 9.75 feet (3.0m). e Alli power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be used.

@ The power cord set must have a minimum current capacity of 7 A anda nominal voltage rating of 125 or 250 volts AC, as required by each countrys power system.

@ The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet C13 connector, for mating with appliance inlet on the computer. xvi Users Manual Country-Specific Power Cord Set Requirements The requirements listed below are applicable to the specific country listed:

Accrediting Applicable Note Country Agency Numbers Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark = ~~ ~~~~SdDEMKO. O(SOCTCOCOCOCOCCS Finland FIMKO 1 FranceSOSOSC*;*;UTR:SCO*~<(CSNNNNNSCOC;*SNSC;(C;S Germany VDE 1 Italy IMQ 4 Japan JIS 3 The Netherlands KEMA 4 Norway NEMKO 1 Sweden SEMKO 1 Switzerland SEV 1 United Kingdom BSI 1 United States UL 2 Notes:

Z 1. Flexible cord must be Type HOS5VV-F, 2-conductor, 1.0 mm? conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used. 2. Flexible cord must be Type SVT or equivalent, No.18 AWG. Wall plug must be a two-pole grounding type. 3. Appliance coupler, flexible cord, and wall plug must bear a T mark and registration number in accordance with the Japanese Dentori Law. Flexible cord must be Type VCT or VCTF, 2-conductor, 0.75 mm? conductor size. Wall plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (15 A, 125V) configuration. Power Cord Requirements xvii

& Taurus (Windows XP) - English.fm Page 1 Thursday, March 28, 2002 6:06 PM Using Your Documentation Congratulations on your purchase of a notebook computer with the Windows XP operating system. Whether you are new to using a portable computer or are an experienced user, this users manual can help you get the most from your computer. Manual Documentation Conventions information Icons Three icons and their associated messages appear in this manual. The information icons are placed before the step/information they apply to:

ea Warning:

Indicates the possibility of personal injury. Caution:

Warns you of possible damage to equipment or data. Note:

Informs you of special circumstances. Technical Information:

Informs you of special requirements or limitations for use of item(s). Keyboard Conventions Keys that you need to press to perform certain functions are displayed in the manual using a small graphic of the button. For example: <Ctrl>

<CtrI> indicates the control key (Ctrl on the keyboard). If you need to press two keys at the same time, the key names are shown joined by a plus sign. For example:

Ee | ) or <Fn+F8>

means that you should press the Fn key and hold it and then press the F8 key. Using Your Documentation 1 e

@\|e mal es Taurus (Windows XP) - English.fm Page 2 Thursday, March 28, 2002 6:06 PM CD-ROM Device Naming Convention In many installation programs you will have to get a program from the CD-ROM device. The program installation sequence assumes that the CD is drive d:\, however this is not always the case. The name of the CD-ROM drive is the letter following the letter assigned to your last HDD. For instance, if you have one HDD with two partitions, the HDD is drives C: and D: and the CD-ROM drive is then drive E. Touchpad Conventions You may be asked to click or double-click on items on the display screen. As a general note the touchpad actions act much in the same way as a wheel mouse, any differences are explained fully. The object that needs to be clicked upon will be displayed in Bold text or shown in a small figure such as the Start Button shown on the right =>. Table 1. Touchpad Click Conventions Action Process Click Depress the touchpad left button and release Double-Click Quickly click the left touchpad button two times Windows Conventions:

A Almost all Windows programs will display the name/function of a button or icon if you place the touchpad pointer on the item you want information about. Software User Documentation Your computer is shipped from the factory with several software programs installed. The software may include its own online or printed documentation. Refer to the documentation or the Help options in the software for more information. The figures and illustrations in this manual may not be identical to those on your system. General Icon Note:

Some of the Icons used in Windows XP may be placed on the taskbar by selecting (ex: Place the volume icon in the taskbar) in the properties dialog box. 2 Users Manual oe

| @ Taurus (Windows XP) - English.fm Page 3 Thursday, March 28, 2002 6:06 PM Introducing Your Computer Your computer is a lightweight portable computer that includes features such as Dolby Digital & Dolby Home Theater System support, CD-ROM/floppy drives, Biometric

(fingerprint) security system/Memory Stick (factory options) and wireless LAN capability (factory option), to meet your computing needs at home or on the road.

[Figures may be different depending on options). Where Everything Is The next 7 figures will explain the location of all of the buttons, LEDs and equipment needed to operate your notebook computer. Front This figure shows the Biometric Security option installed. NOTE:

The Biometric Security Pad will be replaced by the protective cover if the option is not ordered. Ree eerie]

ELOY eer Power Button Biometric Security-

pad Protective Cover Speaker LCD Latch Speaker Introducing Your Computer 3 ee Taurus (Windows XP) - English.fm Page 4 Thursday, March 28, 2002 6:06 PM Buttons and LEDs User Programmable Button E-Mail Button Intemet Button Power Button HDD Access lcon Scroll Lock Icon CD Access Icon Number Lock Icon FDD Access Icon Caps Lock Icon Stop/Eject-Power Off Power, Play/Pause

& Track indicator Volume Up Power On-Play/Pause Previous/Fast Search-Reverse Volume Down Next/Fast Search-Forward Power LED Battery Status LED Right Side CD/DVD - ROM 4 Users Manual Taurus (Windows XP) - English.fm Page 5 Thursday, March 28, 2002 6:06 PM Left Side falc ar cut i PC Card Eject Button Modem Port Headphone / S/PDIF Jack LAN Port Microphone Jack Fan Vent FIR

* Factory Option Parallel USB Ports Printer Port External Monitor Port Serial Port PS/2 Port 1394 Port DC-In Port VHS TV-Out Port Bottom Flex-Bay Latch Flex-Bay Compartment Introducing Your Computer 5 6 Taurus (Windows XP) - English.fm Page 6 Thursday, March 28, 2002 6:06 PM ~

f Using Your Computer for the First Time This section gives you detailed information on using your computer for the first time. Installing the Battery To install the battery pack:

1. With the computers power off, close the LCD panel and turn the computer over so the bottom of the unit faces up. Insert the battery into the battery compartment, ensuring the correct orientation so that the battery fits in its slot properly. 2. Place the battery inside and against front side of the computer battery compartment at an angle of approximately 30 degrees. 3. Push the battery down until the latch snaps into place, securing the battery. 6 Users Manual

@ Taurus (Windows XP) - English.fm Page 7 Thursday, March 28, 2002 6:06 PM Attaching the AC Adapter Your computer runs on power from the battery in the computer or from an electrical outlet. The first time that you use your computer, fully charge the battery by attaching the power cord to the computer and to an electrical outlet. When not used, battery can discharge fully in 2 to 3 months. The battery may have discharged in the time it took for the computer to go from the factory to you. Z All batteries lose their charge if they sit unused for an extended time period. To attach the power cord:

1. Plug the AC adapter into the power connector on the back side of the computer. 2. Connect the power cord to the AC adapter and then to an electrical outlet. AC Adapter The battery starts charging as soon as you plug the power cord into an electrical outlet. The battery charges faster if the computer is turned off during charging. If the battery is fully depleted and the computer is turned off, the battery charges in about 3 hours. If the computer is turned on, the battery charges in about 6 hours. When the battery is charging, the battery charge light is red. When the battery is fully charged, the light turns green. See Using Power Management Options on page 53 for more information on using your computers battery. Using Your Computer for the First Time 7

@ Taurus (Windows XP) - English.fm Page 8 Thursday, March 28, 2002 6:06 PM Turning On the Computer To turn on the computers power for the first time:

1. Push the LCD cover button, located on the front of the computer below the Audio DJ. 2. Lift up the cover. 3. Press and then release the power button. The power light is on when the computers power is on. ower Button Cover Latch Button Power Light Initial Computer Startup:

The first time you start your computer you will see the operating system registration screens. Simply read each screen and follow the simple directions. You must complete this process in order to use your computer. A tutorial is provided if you require it. Adjusting the LCD Display You may wish to adjust the LCD (Liquid-Crystal Display) when you begin using your computer. A TFT (Thin-Film Transistor) LCD does not require adjustment for contrast because the contrast is set to remain at maximum. To adjust the LCD:

: <Fn+Up Arrow> to increase the display brightness.

<Fn+Down Arrow> to decrease the display brightness. 8 Users Manual

| @ Taurus (Windows XP) - English.fm Page 9 Thursday, March 28, 2002 6:06 PM @ 6 Turning Off Your Computer Prior to shutting down your computer ensure ail of your data and current work are saved. The system will ask if you wish to save any unsaved work, saving your work first will speed the shutdown process. To turn off the computer, complete the following steps:

1. Click on the taskbar. If you need to restart your computer after software (re)installation or because it is not responding select the Restart option in step 3 below. 2. Click Shut Down Compute below. 3. Click Turn Off o complete the shutdown sequence. Power Off:

Ifthe system does not power off, then press and hold the power button for over 5 seconds. See "Using Power Management Options on page 53. Power Button Functions:

The power button has several functions other than just turning on and off your computer, see Using Power Management Options on page 53. perform a soft boot by saving your files and pressing

|<Ctrl+Alt+Del> to pop-up the Windows Task Manager window. Click Shut Down > Restart. You can perform a cold boot by pressing the power button for more than 4 seconds to turn the computer off, waiting more than five seconds, and then pressing the power button to turn the computer on. The system may perform some extra checks during the restart. Using Your Computer for the First Time 9 el} > >

| @) Taurus (Windows XP) - English.fm Page 10 Thursday, March 28, 2002 6:06 PM

Tips for Using Your Computer The following information helps you avoid potential problems as you use your computer:

Do not try to disassemble your computer. Opening the system chassis voids your warranty. Only an authorised manufacturer service center can replace or add any parts inside the chassis. Follow all the instructions and cautions in your computer user documentation.

@ The LCD has a polarized surface and can be damaged easily. To prevent damage, avoid touching the screen. Use only approved AC adapters, auto adapters, memory modules and other options. Because a notebook computer is small and has restricted air flow around components, it is more likely to overheat than a desktop computer. A fan inside your computer runs when needed to help eliminate heat. Make sure the fan vent on the left side of your computer is not blocked when you use the computer. Occasionally check the vents and remove any accumulated dust on the outside. e Avoid using or storing the computer in extremely hot or cold areas, such as a car on a hot day. Keep the computer away from heaters and out of direct sunlight. Exposure to excessive heat may damage computer components. If you have left your computer in a hot place, let it cool down slowly to room temperature (with the LCD panel open) before using it. Do not remove the memory-module compartment door, or try to install a memory module when the computer is on. (For information on installing memory modules, see Installing a Memory Module on page 65.) Set up your computer work area to avoid physical strain. Sit with your back straight and supported by your chair. Adjust your chair or work table so that your arms and wrists can remain in a relaxed position, parallel with the floor. Avoid bending or twisting your wrists as you work. Your hands should float slightly above the keyboard. Refer to a book on office ergonomics for more information on setting up your work area. Take frequent breaks from working at the computer to rest your eyes and stretch your muscles. Remember to save your data files frequently and to make backup copies of your files. 10 Users Manual

@| /o Ie -~

@|\e-

@ Taurus (Windows XP) - English.fm Page 11 Thursday, March 28, 2002 6:06 PM $

Travelling with Your Computer Air Travel If you are travelling by air, follow these tips:

Take the computer with you as carry-on luggage. Do not check the computer with your baggage. Allow the computer and disks to go through the X-ray security devices. Do not hand-carry disks through the walk-through metal detectors, which can cause loss of data.

@ Make sure that the battery is charged or the power cord is easily accessible. You may be required to turn on the computer for airport security personnel. Be prepared to turn off the computer during take off and landing. Locking your Computer As a precaution when you are travelling or using your computer in an unsecured area, you should keep your computer as safe as possible. An option to do this is the Security Lock System. Follow the Security Lock System manufacturers instructions for specific installation and use. The following figure shows generally how to use the lock. From Lock Using Your Computer for the First Time 11

@ Taurus (Windows XP) - English.fm Page 12 Thursday, March 28, 2002 6:06 PM Handling Spills Do not spill anything on your computer. The best way to avoid spills is to avoid eating and drinking around your computer. If you do spill something on your computer, turn off your computer, unplug it immediately, and do the following:

Ifyou spill liquid on the keyboard, drain as much of the liquid from the keyboard as possible. Be careful not to let the liquid drip onto the LCD panel. Allow the system to dry for several days before trying to use it. If you spill liquid on an external keyboard or keypad, unplug it and drain as much of the liquid as possible. Allow the keyboard to sit at room temperature for a full day before trying to use it. Sweet liquids leave a sticky residue that may jam the keyboard despite your efforts to dry it. If you spill liquid on the LCD panel, clean it immediately with a soft cloth and denatured alcohol or a proprietary LCD screen cleaner. Do not use water, window cleaner, acetone, aromatic solvent, or dry, rough towels to clean it. Some liquids damage the polarized LCD screen. If your screen is damaged, contact your authorized manufacturer's service center for a replacement. Storing the Computer for Long Periods If possible, leave the power cord connected to the computer and an electrical outlet when the computer is not in use. This extends the life of the battery and keeps the battery fully charged. If you will not be using the computer for a long period of time (a month or more), you should charge the battery until it is completely full. After you have done so, remove the battery from the unit. 12 Users Manual

& Taurus (Windows XP) - English.fm Page 13 Thursday, March 28, 2002 6:06 PM @ G Using the Keyboard Your computer has an 87/88-key keyboard. By pressing designated key combinations, you can have access to all the key functions of a full-sized keyboard. Function & Special Purpose Keys Cursor/Screen Contro] Keys Embedded Numeric we Application Key Ki y Function Windows Key Key Although the layout of the keys on your computers keyboard is different from that on a desktop computers keyboard, the keyboard feels like a full-sized keyboard when you use it. The keys on the keyboard can be grouped into the following categories:

Full-sized Alphanumeric typewriter keys are arranged like a standard typewriter keyboard and are used for text entry. The Windows keys on either side of the spacebar open Windows menus and perform other special functions. Function keys, when pressed together with the functions. key, enable special

@ Cursor and Screen control keys move the cursor. They may perform other functions, depending on your software. Using the Keyboard 13

@ Taurus (Windows XP) - English.fm Page 14 Thursday, March 28, 2002 6:06 PM

To clean the computer keyboard, use slightly damp cotton swabs. Scrub the keys and the surface around the keys. Using the Numeric Keypad Your keyboard includes a numeric keypad, which is a group of keys that you can set to type numbers and mathematical symbols, such as the plus sign. A number or symbol on the right corner of each keypad key shows its numeric function. Num Lock LED Press {

keyp enabled and the Num Lock LED turns on. (See "Reading the System Status Lights on page 20 for the location of the Num Lock LED.) While the numeric functions are enabled, you can temporarily return a key to its normal function by pressing and the | | key. For example to type the letter m, press { al+{ :

this operation displays the letter m.

(J) again. The Num Lock LED turns off. Ysa To turn the numeric keypad off, press 14 Users Manual Do not allow liquid to drip into the keyboard or you may damage the keyboard. Taurus (Windows XP) - English.fm Page 15 Thursday, March 28, 2002 6:06 PM

Using Special Function Keys The function key activates special functions when it is pressed in combination with another keys. Table 2 shows the special key combinations. Table 2, Description of Special Function Key Combinations Key Combinations Key Name Key Function F2 Gauge Displays the battery gauge in the upper-right comer of Gauge your screen. The gauge closes in a few seconds, or you can press

<Esc> to close the gauge. (See "Monitoring the Battery Charge on page 43 for more information on the battery gauge.) This function will also display status of Wireless LAN and S/PDIF functions. F4 CRT/LCD: Switches the display between the LCD, the external CRT/LCD monitor, and simultaneous display on both the LCD and the external monitor. FS Rest: Puts the computer into Suspend mode. To resume Rest: normal operation from rest, press the power button. (See

"Using Power Management Options on page 53 for more information about the rest mode.) F7 WLAN Toggles the Wireless LAN function On/Off WLAN F8 S/PDIF: Toggles the S/PDIF function On/Off S/PDIF F10 Scroll: In some applications, sets the cursor-control keys to Scroll scroll the page up or down while the cursor position does not change. Pressing key combination again tums off the scrolling function. PgUp Volume up: Increases the audio volume. Volume up:

PgDn Volume Decreases the audio volume. Volume down:

down:

End Mute: Mutes the audio. Mute:

Up Arrow Brightness Increases the LCD brightness. Brightness Up:

Up:

Down Arrow Brightness Decreases the LCD brightness. Brightness Down:

Down:

When you press a function key combination, the system sound may be temporarily muted. Using the Keyboard 15 4

| $ Taurus (Windows XP) - English.fm Page 16 Thursday, March 28, 2002 6:06 PM User Defined Buttons (SENS Keyboard) You may program the three buttons to the left of the power button to start any program you have installed on your computer. User defined program Intemet Explorer Outlook Express The default settings for these buttons are:

Windows Calculator Internet = E-Mail - Outlook To reprogram the Sens Keyboard, follow the steps below:

1. Double-Click BS. icon on the Windows taskbar, the Key Setting window is displayed. 2. Select Button you wish to reprogram from the drop down menus in the Key Setting window. 3. Use the Browse button to locate the program you wish to assign to the SENS Keyboard button selected. 4. Click on your program choice to select it. 5. Click Open. 6. Click OK to close window and complete programming the Sens Keyboard. 16 Users Manual

| @ Taurus (Windows XP) - English.fm Page 17 Thursday, March 28, 2002 6:06 PM

Using the Touchpad Your computer is equipped with a touchpad, which is an integrated-pointing device that is used to perform standard mouse functions. The touchpad is an advanced and reliable pointing device that works with a touch of your finger. Scroll Button Press on the touchpad gently. The touchpad responds to light pressure. Table 3. Using the Touchpad Action Process and Comment Click/Tap Process Depress the touchpad left button and release or position the pointer over the object and Quickly tap the touchpad once with your finger. This action is called clicking. Comment This will cause a process to begin or select an object on the screen. Using the Touchpad 17 eo |e ee

Taurus (Windows XP) - English.fm Page 18 Thursday, March 28, 2002 6:06 PM a ee Action Double-Click/Ta Process and Comment SS Process Quickly click the left touchpad button two times or positlon the pointer over the object and Quickly tap the touchpad twice with your finger. This action is called Double-clicking. Comment This will cause a process to begin or open a file folder. Process Depress the left touchpad button and do not release. Comment This is used to move/drag objects to new locations. See "Drag (Move) on page 19. Right-Click Process Position the pointer over the object. Quickly press and release the right button once. This action fs called Right-clicking. Comment This is usually used to obtain information about an object or access a short cut menu. Scroll Up Scroll Down Process Place your finger on the top half of the button to scroll up the current window. Comment Moves the current window down. Process Place your finger on the bottom half of the button to scroll up the current window. Comment Moves the current window up. 18 Users Manual PS/2 Mouse Menu:

You may change the setup in Setup > Advanced Menu Disabled :

Enabled:

Prevents any installed PS/2 mouse from functioning, but frees up IRQ12. Forces the PS/2 mouse port to be enabled regardless if there is a mouse present. Auto Detect : Enables the PS/2 mouse only if present. 4 Taurus (Windows XP) - English.fm Page 19 Thursday, March 28, 2002 6:06 PM Drag (Move) To move a window on the desktop, complete the following:

1. Click the window title bar or icon in the bottom of the window which you want to drag using the touchpad. 2. Press the left touchpad button and hold it. 3. Drag the window using the touchpad. Cursor in Windows Title Bar Click the Window Drag your finger to Title Bar and Hold move the window Area or Multiple item selection:

The drag function may be used to select an area or multiple items in an area by clicking in one area and then dragging to create a selection window. The items inside the window will be selected. Using the Touchpad 19 4

Taurus (Windows XP) - English.fm Page 20 Thursday, March 28, 2002 6:06 PM Reading the System Status Lights System Top System Status lights show the status of computer functions. LED Name Function Sg HDD Access Blinking Green - HDD is being accessed. Or CD Access Blinking Green - CD is being accessed. A

(2 FDD Access __ Blinking Green - FDD is being accessed. i Num Lock Changes a portion of the keyboard to a numeric keypad.

(T] See "Using the Numeric Keypad on page 74. co Caps Lock Changes all alpha or letter input into capital letters. A No changes occur to numeric and special keys. Scroll Lock Scroll lock in certain software. System Bottom LED Name Function VA Power Green - System power on.

-O: Blinking - Standby mode. Amber - Charging.

+ Battery Status Green - No battery pack installed/battery fully charged.

= Blinking - Bad Battery 20 Users Manual 6 Taurus (Windows XP) - English.fm Page 21 Thursday, March 28, 2002 6:06 PM Connecting to the Internet This section explains how to connect you to the internet. For details on how to establish the connection contact the Internet Service Provider [ISP] or system administrator

[SysAdmin]. Using the Modem Install the Modem cable by simply plugging the cable into the modem slot as shown in the figure below. Your Notebook computer will have a Modem/LAN installed. 1. Contact your Internet Service Provider to obtain information or CD required to make the connection in your area. 2. After the cable is connected create a Dialup connection by clicking Start > Control Panel > Network and Internet Connections. 3. Click Set up or change your Internet connection > Setup to start the connection wizard. 4. Follow the instructions in provided in the Make New Connection wizard. Connecting to the Internet 21

@||\e 4

Te

@ Taurus (Windows XP) - English.fm Page 22 Thursday, March 28, 2002 6:06 PM Precautions Before Use Couniry Selection Country Selection:

Because your computer is very mobile you must ensure you select the country you are calling from is selected correctly, otherwise you may experience connection problems. To change the country selection proceed as follows:

1. Click Start > Control] Panel > Network and Internet Connections. 2. Click Phone and Modem Options. 3. Click on the connection you wish to edit in the Locations: box. 4, Click Edit in the Dialing Rules Tab 5. Select the Country/region you are calling from in the General tab. 6. Click OK to close the Edit Locations box. 7. Click OK to close Phone and Modem Options box. Digital Phone Lines:

If you connect the modem to a digital phone tine (such as a company 4-wire system), the modem may be damaged. DOS support Windows XP: Does not support pure DOS mode and the modem does not support a DOS box in Windows. So you cannot use a communication application which runs under DOS. Using the Modem on a PBX system If you use a Windows Communication Program:

Click Start > Control] Panel > Network and Internet Connections. Click By Phone and Modem Options. Click Properties in the Modems tab section. Click OK to close the dialog box. Click OK to close Modem Properties dialog box. Awbs ery 22 Users Manual Check off Wait for dial tone before dialing check box in the Modem tab section. 4

es Taurus (Windows XP) - English.fm Page 23 Thursday, March 28, 2002 6:06 PM If you use a simple terminal program (i.e. hyper terminal):

Type the ATX3&W or ATX3 command as an initialization command. MODEM Notes:

7 1. Inorder to use the 56K feature, be sure to check if the standards supported by the on-line service provider and the modem are identical. 2. If you use a PBX phone system, you can not connect using the 56K mode. 3. Internationally connected calls will be limited to 33.6K (Max.) Using the LAN You may connect to the network using either a LAN cable or by establishing a wireless connection if factory option is installed. Cable Connection Install the LAN cable by simply plugging the cable into the slot in the left side of the computer. Your computers LAN adapter is ready to use for most situations, however if your system does not have a DHCP server or you wish to personaily configure your LAN connection, proceed as outlined in Configuring Network Environment below. Network Protocols:

You may need to consult your SysAdmin if their network protocols and settings are required for your LAN environment. Connecting to the Internet 23

6 Taurus (Windows XP) - English.fm Page 24 Thursday, March 28, 2002 6:06 PM @ @

Configuring Network Environment Configure the Network Adapter as follows:

1. Click Start > Control Panel > Network and Internet Connections 2. Click @ icon (Network Connections). Configure Adapter Only (Not Connected to Network) If your network is not active or the cable is NOT connected double click the icon (Labeled Local Area Network) then follow the instructions starting wi step 4 below. 3. Right-Click the 2 icon (Labeled Local Area Network) then click Properties button. 4. Select Internet Protocol (TCP/IP) in the This connection uses the following items: box. teh -

. Eequoasin Cored Fest ney Cimnek Tor Sted a $ xa) PE (OPS bona eneaialcn anid be areincted Yee gay 3a? cating aaa) hee Bey F coche. mapedds RBar Been wuvael ane panttnok abkudion ke Bi debate beg. 24 Users Manual e Taurus (Windows XP) - English.fm Page 25 Thursday, March 28, 2002 6:06 PM 6. Click Use the following IP address in the General tab 4. In the Use the following IP address box, enter your IP address:, subnet mask:

and Default Gateway:. 8. In the Use the following DNS server addresses box, Enter your Preferred DNS server: and Alternate DNS server:. 9. Click OK when you finish the TCP/IP set-up. Wireless Connection (Factory Option) Your computers wireless LAN adapter is ready to use for most situations, however if your system does not have a DHCP server or you wish to personally configure your wireless LAN connection, proceed as outlined in Configuring Network Environment below. FCC statement for Wireless LAN use:

While installing and operating this transmitter and antenna combination the radio frequency exposure limit of 4mW/cm? may be exceeded at distances close to the antenna installed. Therefore, the user must maintain a minimum distance of 20cm from the antenna at all times. This device can not be co-

located with another transmitter and transmitting antenna. The table below shows the Windows taskbar icons for the wireless LAN. SS Icon Name Description el Connection Displays if connection is available. Established Connection Displays if connection is unavailable. Unavailable To display relative Signal Strength:

1. Double Click the gg icon in the taskbar to display the Wireless Network Connection Status window. This window also displays connection Status, Speed, Duration and Activity. Network Protocols:

You may need to consult your System Administrator if their network protocols and settings are required for your wireless LAN environment. Connecting to the Internet 25

@ eS Taurus (Windows XP) - English.fm Page 26 Thursday, March 28, 2002 6:06 PM f eo e-

ia Configuring Network Environment Configure the Wireless Network Adapter as follows:

1. Click Start > Control Panel > Network and Internet Connections icon (Network Connections) 3. Double-Click the Wireless Network Connection icon. The Connect to Wireless Network window pops up. 4 2. General Office Nel F--| & Supervisor Office Net 4. Select one of the available networks in the Available networks section, if displayed. No networks are displayed A Office - Consult your system administrator. Home - Verify your access point is working properly. 5. Click the Connect button. The Wireless Network Connection icon in the control panel will show your connection is Enabled. You may proceed using the network as normal wired LAN connections. Change Wireless Network Access Point as follows:

1. Right Click the Wireless Network Connection icon. 2. Click View Available Wireless Networks. The Connect to Wireless Network window pops up. 3. Select the new network from the available networks in the Available networks section, if displayed. 4, Click Connect button. The Wireless Network Connection icon in the control panel will show your connection is Enabled. You may proceed using the network as normal wired LAN connections 26 Users Manual

6 Taurus (Windows XP) - English.fm Page 27 Thursday, March 28, 2002 6:06 PM Using the Flex-Bay The Flex-Bay provides an impressive array of secondary storage devices listed below:

CD-ROM drive:

Shipped with some computers is also an available option. CD-ROM R/W drive:

Shipped with some computers is also an available option. DVD-ROM drive:

Shipped with some computers is also an available option. DVD/CD-RW Combo drive:

Shipped with some computers is also an available option. Optional secondary hard drive:

Available as an option for your computer. If your operating system is Windows, you must install the Softex Bay Manager software on the software CD in order to use the Bay Manager Utility to hot-

swap the devices. If you do not use Windows, make sure that the computer's power is off before you remove or install any devices. Swap a Flex-Bay Device - Power On You can use the Softex Bay Manager utility to hot-swap your devices in the flex-bay. To start the Softex Bay Manager utility:

1. Click Start > Control Panel > Other Control Panel Options > Softex Bay Manager.

-or-

2. Double-Click the SwapBay icon in the Windows taskbar. Using the Flex-Bay 27

@||e

@ Taurus (Windows XP) - English.fm Page 28 Thursday, March 28, 2002 6:06 PM Device Swap To swap a device with the power on proceed as follows:

1. Start the Softex Bay Manager Utility. You do not have to turn the computer over or tip it on its side to change devices. Simply tilt the computer up about 10 cm at the back and locate the Flex-Bay latch. See Figure below for the location of the Flex-Bay latch. The computer in the figure is turned over for clarity. 2. Click Remove / Swap. A Device Change popup window stating, Please wait until the system processes the device change appears then another popup window appears and says, Please remove or swap your bay device(s) now and press OK. 3. Tilt the computer up & locate the smart bay latch. 4. Slide and hold the device latch toward the rear of the computer. 5. Slide the device out. 6. Slide the new device in 7

. Click OK. The message Please wait until the system processes the device change appears again. 8. Click OK to close the Softex Bay Manager Utility. 28 Users Manual

@ Taurus (Windows XP) - English.fm Page 29 Thursday, March 28, 2002 6:06 PM Swap a Flex-Bay Device - Power Off Device Swap To remove a device with the power off proceed as follows:

Turn the computers power off. Tilt the computer up & locate the smart bay latch. Slide and hold the device latch toward the rear of the computer. Slide the device out. Carefully slide the new device into the bay. AUPE RE Push the device in until it is flush with the chassis and the Fiex-Bay latch snaps into place. Your computers operating system automatically recognizes the device in the Flex-Bay and configures your computer accordingly when power is restored. Using the Flex-Bay 29

ele 4

ha

. Taurus (Windows XP) - English.fm Page 30 Thursday, March 28, 2002 6:06 PM Using the Disk Drives To use the Floppy drive or the CD-ROM drive you must verify it is installed in the flexbay slot. To swap devices see Using the Flex-Bay on page 27. Using the Floppy Disk Drive Your computer comes with a 1.44 MB, 3.5-inch, floppy drive. To use a floppy disk in your computer, insert it into the floppy drive. Floppy Disk Eject Button To remove a floppy disk, press the floppy disk eject button on the front of the floppy drive. To protect the data on your floppy disks, follow the manufacturers guidelines. Using the CD/DVD-ROM Drive Compact discs are designed so that you can easily insert one into the computer when you need it, and then remove it. See Using the Flex-Bay on page 27 for information on installing the DVD-ROM drive into the computer. DVD Notes:

A DVD player is a factory option and if you ordered this option you will have to install the provided DVD software to view the DVD Title. 30 Users Manual e Taurus (Windows XP) - English.fm Page 31 Thursday, March 28, 2002 6:06 PM

ee a 1. Press the button on the CD-ROM or DVD-ROM drive, and the tray slides out.

(Do not lean on the tray; because it will not support much weight.) CD/DVD Drive Warnings:

Do not place reflective objects other than the CD/DVD disks in the disk slot because of possible hazardous laser emissions. The laser beam used in this CD/DVD-ROM drive is harmful to the eyes. Do not attempt to disassemble the CD/DVD-ROM drive. Refer servicing to your authorized service center. Do not touch the CD/DVD lens, doing so may damage the device. CD/DVD Precautions:

The tray may be stuck, in which case straighten out a paper clip, ~~~2s:,,, insert it into the Emergency Eject hole in the front of the CD/DVD-ROM and push it until the tray ejects. ALED on the drive tray is on when the computer is reading from a CD. Do not remove a disc when this LED is on. To clean a CD/DVD, wipe from the center outwards with clean and dry cloth. Remove the CD/DVD when the drive activity LED is off. 2. Insert a CD/DVD, label side up (or remove a disc, if you have finished using it). 3. Push the tray in gently to close the drive tray. cc CD-ROM Light Eject Button Emergency Eject Button Install and/or start a CD-based program as you would run a program on a floppy disk. Using the Disk Drives 31 o|

@| |e

& Taurus (Windows XP) - English.fm Page 32 Thursday, March 28, 2002 6:06 PM Using the Memory Stick (Factory Option) The Memory Stick is a factory option that will increase your computer storage capacity as well as increase data portability. The Memory Stick may used in many types of equipment such as digital cameras and PDAs for example. Memory Stick and 23 are a trademarks of the Sony Corporation. Memory Stick Support The Magic Gate model is not currently supported. Inserting the Memory Stick To insert the memory stick proceed as follows:

Ensure you Insert the Memory Stick into the slot with the correct orientation

(Name Up) so that the Memory Stick will operate properly and be recognized by the computer. 2. Then push the Memory stick in until it clicks into place. 32 Users Manual

| e Taurus (Windows XP) - English.fm Page 33 Thursday, March 28, 2002 6:06 PM $ 6 Using the Memory Stick The Memory Stick is used the same as the FDD drive on your computer but with much larger capacity, currently up to 128MB. Formatting the Memory Stick A The Memory Stick may need to be formatted before use, if so insert it into the slot and format it the same as the FDD Drive. Protecting Data on the Memory Stick To prevent overwriting/deleting your data in the Memory Stick, move the slide lock to the Lock position. to see the contents of the Memory Stick:

1. Double Click My Computer on the desktop, the My Computer window opens. 2. Double Click the/

window.

*{ icon in the Devices with Removable Storage section of the Removing the Memory Stick To use the Memory Stick proceed as follows:

, Ensure any operations using the Memory stick have completed before you

% remove it. Otherwise you will corrupt your data. 1. Push the Memory Stick in until it clicks and release. 2. The Memory Stick will pop out ~ 1 cm and then you can slide it out. Using the Disk Drives 33

ia $- $|/@

@ @ Taurus (Windows XP) - English.fm Page 34 Thursday, March 28, 2002 6:06 PM

Working with PC Cards By installing PC Cards, you can add functions to your notebook computer similar to those found on add-in boards for desktop computers. Available PC Cards include:

Input/output, such as modem, network, video capture, and SCSI cards. Storage, such as hard drive and flash memory cards. Your computer includes the following PC Card support:

One PC-Card slot: You can install Type I or II cards in the slot. CardBus hardware and software: CardBus enables the computer to use 32-bit PCMCIA Cards. Windows supports 32-bit and 16-bit PC Cards. Maintaining PC Cards To maintain your PC Cards, follow these guidelines:

Keep cards away from excessive heat, direct sunlight, and liquids. Do not drop, bend, flex, or crush cards when handling. Keep dust, magnets, and static electricity away from PC Cards.

@ When a card is not in use, carry it in its protective carrying case.

@ Some PC Cards include cables that extend from the back of the cards. Be careful not to bend or put excessive strain on these cables. 34 Users Manual o|

@||e-

$l

| eS Taurus (Windows XP) - English.fm Page 35 Thursday, March 28, 2002 6:06 PM Using PC Cards To insert a PC Card into a slot:

1. Push the slot door in with the PC Card. 2. Align the card with a slot and insert the card into the slot until it locks in place. PC Card:

Insert PC card with product information facing up Windows automatically assigns computer resources (such as communication ports and memory addresses) to a PC Card installed in your computer. To remove a PC Card from your computer:

Use the following procedures to remove PC Cards, or you may lose data that is being stored to a card. 1. Click icon on the taskbar. 2. Select the card currently in use, and click the Stop button. The eject button for the card slot operates in two steps, therefore to remove a PC Card:

PCMCIA Card Eject button 3. Push the eject button once to pop it outward then push the eject button again to eject the card. 4. Pull the card out of the PC Card slot. Working with PC Cards 35 e

& Taurus (Windows XP) - English.fm Page 36 Thursday, March 28, 2002 6:06 PM Multi Media Functions/Equipment Media Player The Windows Media player is used to play audio files while the computer is on. You can play audio/video CD files using the Windows Media Player, as well as watching TV, video and listening to the radio through internet. The instructions to play a video CD-ROM are the same as the instructions for the audio CD below. Playing a Audio/Multimedia CD To play an CD follow the instructions below:

1. Insert a compact disc into your CD-ROM drive. 2. Press the eject button on the CD-ROM drive to open the CD-ROM device. 3. Insert a CD, label side up. 4 Carefully push the tray in to close the drive tray. The Windows Media Player button appears on the taskbar if not already there, and the music begins to play. If the disk does not play click Start > All Programs > Accessories >

Entertainment > Windows Media Player. CD LED On:

ALED on the drive tray is on when the computer is reading from a CD. Do not remove a disc when this LED is on.

(28 Py Removing the Audio/Multimedia CD To remove the CD follow the instructions below:

1. Click Start > All Programs > Accessories > Entertainment > Windows Media Player to open the Windows Media Player window, if not already open. 2. Click Stop in the Windows Media Player window or simply close the Windows media player. 3. Press the button on your CD-ROM drive. The drive tray opens and you can remove the CD from the CD-ROM drive. 4. For more information on playing compact discs, see the Help menu in the Windows Media Player window. 36 Users Manual Taurus (Windows XP) - English.fm Page 37 Thursday, March 28, 2002 6:06 PM Audio DJ The Audio DJ can play music CDs and MP3 files while the computer is off. It will not, however play video CDs. Button Operation The buttons & display for the Audio DJ operate as follows:

Button Name Function Volume Down Decreases speaker volume when Audio DJ is on. Volume Up Increases speaker volume when Audio DJ is on. MUTE Press the <Volume Down + Volume Up> buttons simultaneously for ~ 1 sec. to mute the sound. Track Display Indicates power on => If and total tracks available on CD and track playing => >. The > blinks when the music file is paused. Stop/Eject Stops & Ejects the Audio CD. Press the button ~ 3 seconds to tum off power. Audio DJ Power Starts/Pauses the Audio CD and MP3 Files. CD Play/Pause Previous Track/Song Changes the Audio CD to the previous track/song. Fast Search Reverse Next Changes the Audio CD to the next track/song. Track/Song Fast Search Forward Lock Press the <Stop/Eject + Volume Down> buttons simultaneously for ~ 3 sec. to lock the Audio DJ buttons. This prevent changing settings while transporting the computer. Unlock Press the <Audio DJ Power CD Play/Pauset + Volume Down>

buttons simultaneously for ~ 3 sec. to unlock the Audio DJ buttons. Multi Media Functions/Equipment 37

@ Taurus (Windows XP) - English.fm Page 38 Thursday, March 28, 2002 6:06 PM @ |

Using the Audio DJ Play an Audio CD 1. Verify the computer is off and that a CD-ROM device is in the flex-bay. Audio DJ Power Buttons:

If a CD-ROM device is not in the flex-bay, the Audio DJ power button will not energize the Audio DJ player. Computer Button Operation:

All computer and SENS keyboard buttons are non functional while Audio DJ is operating except the Computer Power Button. 2. Press the Audio DJ power button until the icon If is displayed in the track display window [Labeled: DIGITAL AUDIO]. 3. Press the eject button on the CD-ROM drive or the button bar. 4. Insert a Audio CD into your CD-ROM drive label side up. 5. Press the button @ on the Audio DJ. button on the Audio DJ Pause/Resume an Audio CD 1. Press the CD button to pause the CD. 2. Press the button @ again to restart the CD. Stop an Audio CD 1. Press the button 2. Remove the Audio CD, then close the tray. 3. Press the Audio DJ power button @ for ~ 1 second to turn off the Audio DJ player. hl Fast Search an Audio CD to stop and eject the CD. 38 Users Manual

@||e

& Taurus (Windows XP) - English.fm Page 39 Thursday, March 28, 2002 6:06 PM Dolby Digital & Dolby Theater System Your computer supports Dolby Digital & Dolby Theater System through a shared Headphone-S/PDIF jack, located on the left side of the computer. You must use a 3.5 mm (mono)- to RCA cable to use the S/PDIF function as shown in the figure below. URC iat ot Volume Control The instructions below are for controlling speaker volume when the computer is on. To control speaker volume when the Audio DJ only is on see Audio DJ on page 37. Using the Keyboard Changing the volume with your keyboard. Use (] + |

Using the Volume Control Icon Double-Click @ icon in the active program tray. The Volume Control window pops up. Use this window to adjust the volume. You can pop up a simple volume slider by a single click @, icon. to increase the volume. o decrease the volume or EE Movie Maker You can edit audio and video data using this Movie Maker inciuded with Windows XP. It is also possible to make a slide show with each frame or picture. To start the program:

Click Start > All Programs > Accessories > Windows Movie Maker. A Please refer to the on-line help manual to operate the Windows Movie Maker. Multi Media Functions/Equipment 39 e

@||e-

$ Taurus (Windows XP) - English.fm Page 40 Thursday, March 28, 2002 6:06 PM Using the Battery Your computer uses a smart rechargeable Lithium-ion (Li-ion) battery pack for power when the AC adapter is not attached to an electrical outlet. The smart battery gives a accurate measurement of the current battery capacity which helps extend operating time by enabling effective power management in operating systems that take advantage of the accurate information supplied by the battery. Charging the Battery Your computers battery starts charging automatically when you connect the power to the computer and to an electrical outlet. Ifthe computer is off, the battery charges faster than if the computers power is on. Approximate charging times for the Li-Ion battery are e@ 3 hours with the computer off. 6 hours with the computer on. While the battery is charging normally, the battery charge light on the computer is red. When the battery is fully charged, the light changes to green. When you use a new battery pack for the first time or use a battery after a long period of storage, the initial battery life is shorter than normal. Normal battery life resumes after a few discharge-recharge cycles. Follow these rules for charging your battery:

A battery normally discharges power when not used for long periods of time. Be sure to recharge the battery every two months when it is not in use. Make it a practice to discharge your battery fully before recharging the battery. This can help extend the life of the battery. Do not attempt to charge the battery in temperatures of under 5C or over 45C All batteries eventually wear out and lose the ability to hold a charge. You may A need to replace your battery pack after a year of average usage. 40 Users Manual

@ Taurus (Windows XP) - English.fm Page 41 Thursday, March 28, 2002 6:06 PM 4 6 Safely Using the Battery Follow these guidelines to safely use the battery:

Turn off your computer and unplug it if you accidentally:

Expose the equipment to liquid. Drop, jar, or damage the computer. Use only approved battery chargers. Do not disassemble the battery, heat it above 100C, or burn it. The battery used in this computer may cause a fire or chemical burn if mistreated. Your computer's rechargeable battery may be considered hazardous waste. If you replace your battery with a new one:

Keep the old battery out of the reach of children. Dispose of the old battery promptly. Make sure that you follow all local requirements when you dispose of the old battery. Removing the Battery Your computer comes with the battery pack inserted in the computer. To remove the battery from the computer:

1. Turn the computers power off. 2. Close the LCD panel, and tum the computer over so that the bottom of the unit faces up. 3. Slide the battery compartment latch toward the left side of the computer and hold, this raises the battery slightly. 4. Slip your fingernail under the edge of the battery and pull it up and then grab the battery and remove it from the compartment. Using the Battery 41

: @ Taurus (Windows XP) - English.fm Page 42 Thursday, March 28, 2002 6:06 PM

Installing the Battery To install the battery pack:

1. With the computers power off, close the LCD panel and turn the computer over so the bottom of the unit faces up. Insert the battery into the battery compartment, ensuring the correct orientation so that the battery fits in its slot properly. 2. Place the battery inside and against right side of the computer battery compartment at an angle of approximately 30 degrees. 3. Push the battery down until the latch snaps into place, securing the battery. 42 Users Manual

@| |e

@\|\e-

: @ Taurus (Windows XP) - English.fm Page 43 Thursday, March 28, 2002 6:06 PM

@) se Te Monitoring the Battery Charge Battery life is affected by factors such as the power-management settings in System Setup, the applications you use, and the brightness settings of the LCD. Under normal usage, the battery charge lasts approximately 2.5 hours. Battery life estimates are subject to variation. The actual life of your battery may be fess than the estimates given in the manual. You can monitor the charge of the battery pack installed in your computer by using the Power Meter or Battery Gauge. Power Meter The Power Meter displays the charge of the batteries and the current source of computer power, AC or batteries. You may monitor the ba charge or usage by using the Power Meter. To access the power meter click icon on the task bar or click Start > Control Panel > Performance and Maintenance > Power Options >

Power Meter Tab. The Power Status icons shown below are displayed during Battery Charging Operations At ~15% and 10% remaining battery power the current power source and the battery Icons respectively change to the icon shown below and you should follow the instructions in Battery Warnings section below You may also check battery charge by moving the cursor to th L box will display the % of charge. icon, a small dialog Using the Battery 43 o|

@ Taurus (Windows XP) - English.fm Page 44 Thursday, March 28, 2002 6:06 PM @

Battery Gauge You may display the battery gauge while you are in any program by pressing O + . While the battery gauge is being displayed, all keys except disabled. The battery gauge is only displayed for a few seconds. are Power Source: (Top Right) Indicates that the computer is powered by the battery. Indicates that the computer is powered by the AC adapter.

Battery Level: (Lower Right) Indicates the approximate Indicates the computer is on amount of the primary AC power only (No Battery battery charge remaining. Present). Radio Frequency: (Top Left) Wireless LAN On Wireless LAN Off Digital/Analog Audio: (Lower Left) Digital Audio On: Indicates the S/PDIF / Headphone jack is set for digital output. Digital Audio Off: Indicates the S/PDIEF / Headphone jack is set for analog output. You may also determine the charge of your battery by simply pushing the symbol Cc below the word PUSH located on the bottom of the battery. The green LEDs will illuminate to show you the percentage of charge remaining in the battery. 44 Users Manual

@ Taurus (Windows XP) - English.fm Page 45 Thursday, March 28, 2002 6:06 PM Battery Warnings If the battery charge is low (about 10%) you have ~ 5-10 minutes of battery life left. You should:

@ Save your work and, Connect the power cord to the computer or turn off the computer and install a fully charged battery. You can adjust the battery alarm features by using the operating systems power management program (Start > Control Panel > Power Options in Windows). If you cannot run your computer from the battery and the battery will not charge when you attach the power cord, the problem may be that:

The battery temperature is below 0C or over 45C. If you think the battery temperature is too hot or too cold, turn off the computer, remove the battery, and let the battery reach room temperature. Then try charging the battery again. The battery is defective. Replace the battery with a new battery. Battery Calibration Calibrating your battery once a month is one of the recommended methods of increasing your computers battery life. To calibrate the battery complete the following steps:

Calibration Notes:

You should start the battery calibration process with a fully charged battery, battery status LED is green. The power meter may not show 100%. Before you commence the battery calibration process you should fully charge, then fully discharge and finally fuily recharge the battery again. Disconnect the AC power adapter after turning off the system. Restart your computer and press <F2> to enter BIOS setup. Using the arrow keys, highlight Smart Battery Calibration in the Power menu. a Press Enter to start calibration process. The calibration usually takes 2 to 3 hours depending on the current battery charge. 5. When the calibration process is complete, recharge the battery fully. Using the Battery 45

| Taurus (Windows XP) - English.fm Page 46 Thursday, March 28, 2002 6:06 PM Using System Setup The System Setup (BIOS) program enables you to configure your computer hardware and set security and power-savings options. The settings you choose are stored in battery-maintained CMOS memory that saves the information even when the computers power is turned off. When your computer is turned back on, it is configured with the values found in this memory. Run System Setup if you get a message prompting you to run the program. You may also want to run System Setup, particularly the first time you use your computer, to set the time and date, use security or power-management features, or alter the settings of other features. BIOS Caution:

If you are not familiar with BIOS setup and what the parameters mean, seek help from a person who is knowledgeable. Incorrect settings may cause your system to Crash. Your computer's version of System Setup may not include all the fields listed here or may include additional fields. Field names and order of appearance can vary according to the version of the BIOS (basic input/output system) on your computer. Starting System Setup and hold until the To start System Setup, turn on your computer and then press System Setup screen appears. Table 4. System Setup Menus Menu Function Main Changes the basic system. Advanced Configures advanced features on your computer. Security Enables security features, including passwords and backup and virus-check reminders. Power Configures power-management features. Boot Specifies the order of boot devices and configures boot features. Exit Specifies how to exit System Setup. a ES To open the menu you need to use, use the left or right arrow keys to select the menu name. 46 Users Manual o)

: Taurus (Windows XP) - English.fm Page 47 Thursday, March 28, 2002 6:06 PM E Table 5. System Setup Navigation Keys A Navigation Key Function Displays the General Help window. Exits the current menu. Moves the cursor up and down between fields. Selects different menus. Pressing the ESC key at the Main menu brings you to the Exit menu. Scrolls backwards through the options for the highlighted field. Scrolls forward through the options for the highlighted field. Sets the parameters for the current menu to their default values. Sets the parameters for the current menu to their previous values. Executes commands or opens a submenu. Using System Setup 47

@ Taurus (Windows XP) - English.fm Page 48 Thursday, March 28, 2002 6:06 PM $ |

e||@

Changing Booting Priority The Boot menu in System Setup enables you to select the booting device and to set booting options. Boot Device Priority field enables:

You to select the order in which the computer attempts to boot from different devices. The field has four (4) options: CD-ROM Drive, Removable Devices, Hard Drive and Network Boot. To change the booting device priority, choose the device positions by completing the following:

1. At startup, press (23))) to open System Setup.

; to select the Advanced CMOS Setup menu. Highlight the 1st Boot Device option with (

KEES

> YN Press <Shift+Plus> keys until the option moves up in the list to the desired position or press <Minus> key until the option moves down in the list to the desired position. 5, Press <Esc> to return to the Exit menu. 6. Press <Enter> or <F10> to exit and save your changes. 7. Press <Enter> again to restart the computer. lf you want to start the system using a bootable CD, change the CD-ROM A Drive to be the 1st Boot Device. 48 Users Manual Taurus (Windows XP) - English.fm Page 49 Thursday, March 28, 2002 6:06 PM Using System Security This section describes your computer security programs. The first is the standard BIOS security which is standard on almost all computers. The second is a advanced factory option Biometric security system that uses your fingerprint(s) to control access to your computer and individual files if necessary. You no longer have to worry about passwords being lost, stolen or forgotten. BIOS Security The BIOS security operations are explained below:

System Passwords The computer provides (4) levels of password security: administrative-level

(supervisor), user-level (user), HDD access and Password on Boot. These passwords prevent unauthorized access to the computer. The supervisor password enables full access to all System Setup fields. The user password enables full access to only the Set User Password and Password on boot security fields and read access to all other System Setup fields. The HDD Password controls access to the hard drive. You may also enable the biometric security at boot. The (3) security boot time options are:

The Biometric Security software MUST be installed prior to setting the security options to any of the fingerprint options. Disabled Text password Finger Print If multiple users have access to the computer (such as in a network environment), a supervisor password can prevent unauthorized access to certain security options. Choose the type of password security that is appropriate for your work. Using System Security 49

@ Taurus (Windows XP) - English.fm Page 50 Thursday, March 28, 2002 6:06 PM a 2 If You Forget Your Password It is very important that you do not forget your password. If you do, you cannot access your system. Write your password down and keep it in a safe place. If you do forget and cannot find the written note, please contact the Samsung Helpline. Please have your receipts available to verify the type and model of your computer. You may be charged for password removal. Creating a Password To create a password follow the instructions below:

1. At startup, press (. | to open System Setup. to select the Security menu. Precautions for Password Entry:

You can enter letters or numbers, but you cannot use the function keys, such as the Shift key. Your computer does not distinguish between capitalized and lowercase letters in your password. As you type the password, the cursor moves but your password does not appear on the screen. Choose the type of password security that is appropriate for your work. If you want fo set a user password, you must set a supervisor password first.

|| to select Set Supervisor Password or Set User Password. 4. Press <Emter>. The Set Password dialog box appears. 5. Press <Enter> after you have typed your password. The computer prompts you to reenter your password for verification. 6. Type your password again and press <Enter>. A message appears telling you that the changes have been saved. The Password on boot password MUST also be set in order for your machine to boot properly.

) to select Password on boot. 8. Press <Enter>. The Set Password dialog box appears. 9. Select the Text Password option. 10. Press <Enter> again to return to the Security menu.

=| to go to the Exit menu. 12. Press <Enter> or <F10> to exit and save your changes. 13. Press <Enter> again to restart the computer. 50 Users Manual ele >

@ Taurus (Windows XP) - English.fm Page 51 Thursday, March 28, 2002 6:06 PM If password use Is not desired:

Follow the creating a password procedure above except leave the password field empty in step 5. Using System Security 51 9|

@||\e

$F

@ Taurus (Windows XP) - English.fm Page 52 Thursday, March 28, 2002 6:06 PM Biometric Security (Factory Option) The factory optional fingerprint sensor provides unique security access to your computer. You will no longer have to worry about losing or forgetting your password. Since every person has a unique set of fingerprints, only a biometrically enrolled person may have access to your computer. Advantages of Biometric Security are:

@ Very high level of security No password to remember, lose or have stolen. Streamlined logon process. Single fingerprint will access many programs, eliminating passwords. If you purchased the Biometric Security option, please refer to the manual provided for installation and use. 52 Users Manual

~ al e!|@

@ Taurus (Windows XP) - English.fm Page 53 Thursday, March 28, 2002 6:06 PM Using Power Management Options Your computer includes Power Management options that can help the battery charge last longer and extend the life of the battery. Power-management options will slow down or shut off system components when the components are not being used. Power management may slow down system performance. Your computer runs fastest with the power cord attached, when power management is disabled. In the next sections, basic and advanced methods of power management will be discussed. Basic Power Management Schemes This section discusses the basic schemes of power management when the computer is operating on battery power or using AC power. Standby vs. Hibernation Standby unlike hibernation mode does not store unsaved information on your hard disk; it's stored only in the computer memory. If there is an interruption in power, the information is lost. So before putting your computer on standby, you should save your files. Changing Devices:

Do not change PC Cards while in standby or hibernate modes. To enter the power management window complete the following:

1. Click Start > Control Panel > Performance and Maintenance. 2. Click Bs icon to display the Power Options Properties window. Using Power Management Options 53 mal

|e

@||e

@ 4 Taurus (Windows XP) - English.fm Page 54 Thursday, March 28, 2002 6:06 PM 3. Click the Power Schemes tab to display the basic power management options. Power Schemes Tab|

Seloct he power achieve esl tea mest sppropeate setGings Ber whe cemuien, Hite fas chaseping die getings below rel noddy hes calectodd gobectne, 2 Seetiegy or PeskabhL web pemmet Wher numsader ee 4. Select the time that you wish each of the following actions to occur in Battery and AC power mode. e Turn off monitor:

Turn off hard disks:

System standby:

@ System hibernates:

Turning off the monitor and HDDs will save a substantial battery power, therefore when in battery only mode select the shortest time practical.

@ Hibernate Mode (Power Management or Manual Method) When hibernation is used, your computer turns off and when you power up again, everything is restored exactly as you left itincluding programs and documents you may not have saved or closed. Everything in memory gets saved to the HDD, and the monitor and hard disk get tumed off. 54 Users Manual

: o Taurus (Windows XP) - English.fm Page 55 Thursday, March 28, 2002 6:06 PM @ |

If You Reinstall Windows:

You should re-establish hibernate in power options by opening Power Options Properties window and click on the Hibernate tab then click Enable Hibernation. Hibernate Tab When yout eatonda Wtonates, 3 zteaes wate Bh 4 mrarmory an your heed disk dnd then sledy down, When prox Corgadee Oyens aut of Kenaion, # antes 19 AP previoas ates, Frequent Interruptions:

If you experience frequent interruptions, you might also consider putting your computer into automatic hibernation after a specified number of minutes using the power management options.

& Standby Mode (Power Management or Manual Method) Standby is used mainly for conserving battery power in your notebook computer. It also gives you the benefit of getting right back to your work without waiting for the computer to restart. Standby turns off your monitor and hard disks, placing your entire system in a low-power state. When you return to your computer, restores your desktop exactly as you left it. It is recommended that you do not enter standby mode with less than 20% battery power. 5. Click OK to set your power management options and close the window. Rest Key:

The manual (+ E <Fn+F5> key combination will not activate Standby or Hibernate modes whilst you are playing a multimedia program or have an active USB device connected. Using Power Management Options 55 e|* > ~$|/@

@) es

| $ Taurus (Windows XP) - English.fm Page 56 Thursday, March 28, 2002 6:06 PM Advanced Power Management Schemes This section discusses the advanced power management schemes. There are two buttons that you can use to manually conserve power. To enter the power management window complete the following:

1. Click Start > Control Panel > Performance and Maintenance. 2. Click & icon to display the Power Options Properties window. 3. Click the Advanced tab to display the advanced power management options. Advanced Tab Power & Sleep Button Programming Windows

"Basic Power Management Sche on page 53 for a better understanding of Standby and Hibernate modes. 5. Click OK to set your power management options and close the window. You can return to normal operation after you have used one of the Power Management buttons by quickly pushing and releasing the Power button. 56 Users Manual e ia

@ Taurus (Windows XP) - English.fm Page 57 Thursday, March 28, 2002 6:06 PM @

Using the Hard Drive Your computer includes a removable IDE (integrated drive electronics) hard drive. The IDE hard drive can store the data and programs your computer uses. The drive plugs into a connector on the system board. The hard drive that comes with your computer has already been formatted. Do not format the hard drive. Doing so destroys all data contained on the drive. If you need to format a new drive, or want to erase all data on your existing hard drive, refer to the manual for your operating system. Installing/Reinstalling a HDD To install a new HDD you must contact your local service representative. He will do the physical change of the drive. You should complete the instructions below before you go to the service center. See the information below before you install your HDD:

Back up data files of your old hard drive. For system boot with CD-ROM, under the Boot menu in System setup, set Bootable CD Check to Enabled and set Boot Device Priority is ordered starting from the [DVD/CD-ROM]. When you are ready to install the new HDD use the Recovery CD-ROM to install the device driver.

(Re)Installing Windows and Device Drivers Use System Recovery CD to (re)install OS and System Software CD to (re)install device' drivers. to a new HDD or recover from a system crash. Notebook computers that ship from the factory include System Recover CD-

ROM and System Software CD-ROM, which contains a copy of the applications and drivers needed for computer's operating system. In the unlikely event that programs on the computer hard drive become corrupted or are erased, you can use the System Recovery CD-ROM to reinstall your operating system and then System Software CD-ROM to reinstall your original applications and drivers. A The System Recovery CD is used to (re)install the OS and System Software Using the Hard Drive 57 ee 4

ha o Taurus (Windows XP) - English.fm Page 58 Thursday, March 28, 2002 6:06 PM Video Features and Configuration All these video modes can be displayed on an external monitor. However, if you disconnect an external monitor that was attached to your computer and then start the computer, the LCD may revert to a different resolution than the one you chose for the external monitor. Resolution and Colour Depth The resolution of the LCD is the sharpness of the image it can display. Resolution is measured by the number of pixels (individual dots) displayed on the entire screen. In general, the more pixels the LCD can display, the better the image. The number of colours the LCD can display is measured by how many bits the LCD uses to represent each pixel:

@ 16-bit colour can support 64 K (65,536) colours.

@ 32-bit colour can support 16 M (16.8 million) colours. All these video modes can be displayed on an external monitor. However, if you disconnect an external monitor that was attached to your computer and then start the computer, the LCD may revert to a different resolution than the one you chose for the external monitor. Adjusting the LCD Display You may wish to adjust the LCD (Liquid-Crystal Display) when you begin using your computer. A TFT (Thin-Film Transistor) LCD does not require adjustment for contrast because the contrast is set to remain at maximum. To adjust the LCD:

<Fn+Up Arrow> to increase the display brightness.

| <Fn+Down Arrow> to decrease the display brightness. 58 Users Manual e Taurus (Windows XP) - English.fm Page 59 Thursday, March 28, 2002 6:06 PM $

Configuring Display Features The following sections describe how to configure the display settings on your computer. Display Resolution Notes:

When Windows XP is initially installed it will automatically adjust the resolution to maximum available. Changing Colour Depth and Resolution To change the colour depth and resolution of your LCD:

1. Click Start > Control Panel > Appearance and Themes. 2. Click ee icon. The Display Properties window appears. 3. Click the Settings tab. The Settings screen appears. 4 To change the colour depth, click the arrow next to the Colour quality palette and select the available colour depth you want. 5. To change the resolution, click and drag the slider under the Screen resolution until you select the available resolution you want. 6. Click OK. 7. Follow the prompts that appear on the screen. Video Features and Configuration 59 ei ma ma es Taurus (Windows XP) - English.fm Page 60 Thursday, March 28, 2002 6:06 PM @ |

Using Dual View Mode Single View mode is the basic display mode which displays same view on all the display devices connected to a system. Dual View mode is the Extended screen mode supported in Windows, which displays separate views on each display devices connected to a system. ui The default setting on your system is Single View mode. Setting Dual View Mode To set Dual View mode on your system:

1. Connect peripheral display device such as monitor or TV to your system and start the system. Select Start > Control Panel > Appearance and Themes. Click eB icon. The Display Properties window appears. Click the Settings tab. The Settings window appears. Check Extend my Windows desktop onto this monitor. APY PE You can drag the second monitor image to position where you want your extended screen space with respect to the primary monitor (usually the LCD). To confirm whether the system is set properly with Dual View mode:

1. Open Display properties and click Settings tab. 2. Place the cursor on the first monitor picture and click and hold over a second, a number 1 will be shown on the first actual monitor screen. And place the cursor on the second monitor picture and click and hold over a second, then digit number 2 will be shown on the second actual monitor screen. 3. The monitor displays digit number 1 is the primary monitor and number 2 is the secondary monitor. In Windows explorer, the program is displayed on the primary monitor, if you can drag it to the secondary monitor, then Duo View mode is now working properly. 60 Users Manual

: Taurus (Windows XP) - English.fm Page 61 Thursday, March 28, 2002 6:06 PM 6 1

The secondary monitor has a display of 256 colours (colour depth) and 640x480 pixels

(resolution) at first. The colour depth and resolution of primary/secondary monitors are separately changeable. To reset the system to Single View mode:

1. Start Display properties. Click Settings tab. Click the second monitor among two monitor pictures. Uncheck Extend my Windows desktop onto this monitor. Click OK. awe YS Using Dual View Mode 61

@||e-

+ #1 4 Te

@ Taurus (Windows XP) - English.fm Page 62 Thursday, March 28, 2002 6:06 PM Using Multimonitor Mode You may duplicate your LCD screen on an external monitor, television or digital flat panel (DFP). TV Connection Restrictions:

You should only connect/disconnect cables and wires to your computer and TV when the power is off. TV/DFP Support Limitations:

The computer will only support televisions with S-VHS input capability. The standard composite video in port is not supported. You can not use TV-out port to connect to your television or digital flat panel in DOS mode. When TV-Out is activated, your computer screen will not be active. To start using multimonitor mode proceed as follows:

1. Connect the external monitor to the connection on the back of your computer. 2. Press the <Fn> + <F4> key combination, the LCD will be duplicated on the monitor, television or digital flat panel. 4

<Fn> + <F4> key combinations Each time you use the combination changes as follows:

key combination the LCD/Monitor Both displays are displaying the computer output (LCD & Monitor). Monitor, television or digital flat panel only is displayed the computer output. LCD only is displaying the computer output. To stop using multimonitor mode proceed as follows:

1. Press the <Fn> + <F4> key combination until only the LCD is displaying the computer output. 2. Disconnect the external monitor or television from the connection on the back of your computer. 62 Users Manual

Taurus (Windows XP) - English.fm Page 63 Thursday, March 28, 2002 6:06 PM Using Powerplay Powerplay is a program supplied with your graphics adapter to extend battery life while on battery power only. To activate Powerplay proceedas follows:

1. Click Start > Control Panel > Appearance and Themes. icon. The Display Properties window appears. Click the Settings tab. The Settings screen appears. Click the Advanced button. The (Multiple Monitors) and M7 Properties window appears. Click the POWERPLAY tab 6. Click the POWERPLAY button in the POWERPLAY Settings section. The button will change to button and activate the other options available. YN yn Using Dual View Mode 63

- @ Taurus (Windows XP) - English.fm Page 64 Thursday, March 28, 2002 6:06 PM

Using Options You can order the following options for your Notebook computer from your authorised reseller:

An extra AC adapter. An auto adapter that enables you to charge the computers battery and operate the computer while in an automobile. An extra battery pack. 128, 256 and 512 MB DDR SDRAM memory modules that enable you to upgrade your computers memory to a maximum of 1 GB. A CD-ROM drive module (CD Only or CD R/W). DVD/CD-RW Combo drive:

A DVD-ROM drive module. Bluetooth/Wireless FIR (Fast Infrared) Connection 2nd HDD Port Replicator Biometric Security Memory Stick The options that are available may change periodically. Contact your reseller for updated information on current and new options. Memory Modules You can increase system memory by installing optional memory modules. You can install a 128 256 or 512 MB modules. 64 Users Manual To avoid possible system problems, use only approved memory modules in your computer. e |@

eS Taurus (Windows XP) - English.fm Page 65 Thursday, March 28, 2002 6:06 PM Before You Install Memory To prevent personal injury and damage to the equipment, follow the precautions listed here before installing a memory module. Take the following precautions when installing a memory module:

Before you remove the memory module compartment door, turn off the computer, unplug the power cord, and remove the battery. Also, disconnect any peripheral devices. Before handling a memory module, discharge any static electricity by touching a grounded surface or using a grounding wrist strap. Do not insert objects with conductive material, such as metal screwdrivers or graphite pencils, into the memory-module compartment.

@ Be careful in handling the metal plate of the memory door. Installing a Memory Module Handie a memory module carefully. Hold them only by the edges. To install a memory module:

1. Turn the computer over so that the bottom faces up. 2. Using a screwdriver, remove the screw that holds the memory-module compartment door in place. 3. Grasp the edge of the door and pull the door off the chassis. 4, Remove installed modules if necessary:

Using Options 65 e

e Taurus (Windows XP) - Englishfm Page 66 Thursday, March 28, 2002 6:06 PM @ |

5. Align the connector on the memory module with the connector of the slot. 6. Push the memory module into the slot at a slight angle (~45) until the connectors are fully engaged. 7. Push down on the edge of the memory module until the module snaps into place. 8. Align the memory module compartment door with the compartment and push the door down until it snaps into place. 9. Reinstall the screw you removed in step 2. 10. Turn on the computer and perform a complete POST to check the memory integrity. Port Replicator Contact your reseller for a list of port replicator options available for your Notebook computer. Users manuals are included with the port replicator options. Wireless LAN The wireless LAN option allows easy connection to large or small office networks while also providing freedom from the constraints of cables and sockets. To setup and use the Wireless LAN, Please refer to the user manual provided with the option at the time of purchase. 66 Users Manual

# Taurus (Windows XP) - English.fm Page 67 Thursday, March 28, 2002 6:06 PM Bluetooth/Wireless Bluetooth/Wireless technology allows wireless communication between bluetooth communication devices, such as cellular phones, desktop and other notebook computers. To setup and use the Wireless LAN, Please refer to the user manual provided with the option at the time of purchase. FIR (Fast Infrared) Connection BIOS Setup AA ws The BIOS setup must be completed first in order for the option to operate properly. Use f Highlight the /O Device Configuration option with

<Enter>. Highlight the FIR port with |

Press <Shift+Plus> keys until the option changes to Enabled. Press <Ese> to return to the Exit menu.

} keys and press Press <Enter> or <F10> to exit and save your changes. Windows Setup 1. 6. es Te Right click My Computer. Click Properties, the System properties window pops up. Click the hardware tab then click the device manager button in the device manager section. Double click the Infrared devices then double click the IrDA Fast Infrared Port, the IrDA Fast Infrared Port properties window pops up. Click on the Advanced tab and set the device as follows. Select the Infrared Transceiver A in the properties section. Select the Vishay TFDS-6500 in the value section. Click OK Using Options 67 2)

@ Taurus (Windows XP) - English.fm Page 68 Thursday, March 28, 2002 6:06 PM Troubleshooting Complete the following in the order presented until your system is functioning properly. If all of the steps below fail then contact your local reseller for assistance.

> Questions and Answers Please see Questions and Answers on page 69 for assistance in correcting any computer operational problems.

> Check the Connections Verify all of the power and peripheral cables are securely plugged into their sockets and that your system and power supply is on.

> Norton AntiVirus Run Norton AntiVirus to insure a virus is not affecting your computer. To run Norton AntiVirus proceed as follows:

Click Start > Programs > Norton AntiVirus > Norton AntiVirus 2002 Windows Help and Support Run Windows Help and Support to find problem that may be affecting your computer. To run Windows Help and Support proceed as follows:

Click Start > Help

> Reinstalling Software If for some reason your system crashes you may corrupt your HDD, Windows Operating system and/or some of your device drivers. If this is the case, use System Recovery CD to reinstall OS and System Software CD to reinstall the corrupt device drivers. System Recovery Precaution:

Before you start restoring your windows operating system insure you backup all data on your hard drive. Samsung is NOT responsible for any data loss. 68 Users Manual

. @ Taurus (Windows XP) - English.fm Page 69 Thursday, March 28, 2002 6:06 PM

@ |e Questions and Answers Problem The computer does nothing when you turn it on. Some of the letter keys type numbers instead of the indicated letters. Operating System Problems Action Has the battery run down? Connect the power cord to the computer and recharge the battery. Try turning on the computer again. Is the Num Lock light on? If so, the numeric keypad on the keyboard is active. To return the keypad keys to typing letters, press <Num Lock>. Battery power seems to run out faster than expected. Certain software programs hang during operations when there is no interaction If you are running the computer from the battery rather than the power cord, make sure that you set the Idle Mode field in System Setup to On. This setting enables the microprocessor and the hard drive to slow down when the computer is not busy. Your computer may be in Suspend or Rest mode. Tap the touchpad to resume from Suspend or press the power button to resume from rest. ha with the keyboard or peripheral devices. PC Card does not work Make sure that the PC Card is inserted left side up in correctly. the PC Card slot. Check that the card is inserted fully into the slot. If you are using a PC Card modem, check the modem cable connections. Your ATA or Compact A patch is provided for these cards on the Recovery Flashcard do not work. The System Setup settings are not retained when you turn off the computer. CD The CMOS battery inside the computer may need to be replaced. The CMOS battery provides power to save the system BIOS information when the computer is tured off. Normally, the CMOS battery lasts for several years. Do not attempt to open the chassis and replace this battery yourself or your warranty is void. Have an authorized the manvufacturers service center replace the CMOS battery. Troubleshooting 69

& Taurus (Windows XP) - English.fm Page 70 Thursday, March 28, 2002 6:06 PM Problem Action No sound. Verify if the mute check box is checked or the volume is not turned down in the pop up menu by clicking the speaker icon of the task bar. System/BIOS behaves If you caused an abnormal power interruption (.e.. erratically removing battery while on battery power), you may cause BIOS data corruption. 70 Users Manual

@|\o o||@

| @ Taurus (Windows XP) - English.fm Page 71 Thursday, March 28, 2002 6:06 PM Video Problems Problem Nothing appears on the LCD panel when you turn on the computer. Action Adjust the brightness on a TFT LCD. Are you using an external monitor? If so, press <Fn+F4> to return to the LCD panel. Error Message when entering Power Management while in Multimonitor mode. Nothing appears on the external monitor when you switch the display to it. If the secondary monitor is set to 256 colours, this error message could appear. Change the colour of the secondary monitor to high colour (16 bit). Is the monitor properly connected to the computer?

Is the monitors power cord connected to an AC wall outlet? Check the brightness and contrast controls on the monitor. Does the program appear on the LCD panel instead of the external monitor? If so, press

<Fn+F4> to switch to the monitor. Try turning the monitor off and on again. Only the LCD Display works when system returns from Power management mode while in Multimonitor mode. The system resets to the original BIOS setup when the system returns from the power management mode. If the Display mode, in the Advanced menu of BIOS setup is set to LCD, then only the LCD will be turned on when the system wakes up. Set the Display mode in the BIOS to Both to turn on the LCD &

CRT on wakeup. The external monitor displays flashes or waves. Check the cables between the monitor and the computer. Are they properly installed?

Cannot toggle between CRT If you are using the Multimonitor mode, you can not and LCD while playing the _ use the <Fn+F4> key combination and also you 3D game. cannot use this function in 3D games using Direct-

X. There isLCD or CRT has Adjust the resolution and the colour to 1400 x 1050 noise (speckles, lines or raged edges) on the picture when playing a MPEG file with the Media player/ DVD software or using the USB camera, and 32 bit to display clearly, or avoid playing two programs at the same time. In. DOS mode the CRT/LCD button does not work. The LCD only mode is not supported using this Key combination. Troubleshooting 71 e

@||e-

4 Taurus (Windows XP) - English.fm Page 72 Thursday, March 28, 2002 6:06 PM @

ae Problem Action If the connected CRT If the refresh rate is not optimal for the connected monitor display is not steady. CRT, then this problem may occur. To correct this problem do the following:

1.Click Start > Settings > Control Panel. 2. Double Click the Display icon to open the Display properties. 3.Select Settings 4.Click the Advanced button. 5.Click the Adapter tab 6. Adjust the Refresh rate to optimal or other selections until you see the CRT clearly. A S 72 Users Manual Taurus (Windows XP) - English.fm Page 73 Thursday, March 28, 2002 6:06 PM Modem Problems Problem My modem doesn't connect to services or disconnects during communication Action If your modem has difficulty in connecting to on-

line services and sustaining communications, first check if other devices are connected and remove them. Also remove any extension leads. Interference from certain devices or poor line power conditions may degrade the quality of your connection. Under these conditions gradually reduce the communication speed of your modem until a reliable connection is achieved. Check with your on-line service provider. When using a PBX phone system I can't dial on my modem. If you use a PBX phone system you may need to press a number i.e. '9' to connect to an external line, you should enter the following command before trying the connection and check modem initialization. (ATX3&W) And add 9, as the external line prefix (example) of the phone number when using the dial command ATDT9, 123-4567". Screen displays random or garbage characters during communications. After your modem has connected to the on-line service, your screen may display garbage characters or after-images in screen transitions. This problem is caused by a mismatch of the terminal modes between communications service and communications programs. You need to match the terminal modes to each other. Refer to the user's guide of the communications program you're using. Reports error message that insufficient Hard Disk space is available. Delete the unnecessary messages or data you received by Modem or Fax every one to three months as required. If you're using the internet, many picture and data files can get downloaded to your HARD DISK every time you visit a home page, which will consume a lot of your HARD DISK space. For more detailed information about the method of deleting, refer to the help of the Web browser you've been using or your user's guide. Troubleshooting 73 el\> a eS Taurus (Windows XP) - English.fm Page 74 Thursday, March 28, 2002 6:06 PM FAX Problems:

Depending on telephone line status, or types of Fax machines/programs that send/receive the Fax, Fax transmission/reception may not work correctly. In that case, please try other Fax programs. (e.g. Win Fax) Reinstalling Software Windows Application/Driver (Re)Installation If you wish to reinstall drivers or applications, please use the Software CD. If you wish to reinstall the Windows operating system, please use the Recovery CD. Application/Driver (Re) Installation Simply install the driver(s) according to the instructions below:

1. Insert the System Software CD-ROM. 2. Follow the directions provided in the opening window. Windows (Re)iInstallation To reinstall the your Microsoft Windows XP Operating System:

1. Start your computer. 2. Open the CD Drawer and insert the Recovery CD. Close the drawer. 3. When the Recovery Menu appears, select the option as required to restore your system. You have two options for system recovery. The Standard Installation and the User Installation. The Standard Installation Option will SAVE all user data files on your hard disk and restore your operating system to normal. The User Installation Option will DESTROY all data on your hard disk. If you have any data files or other software you do not wish to lose, make a backup of these files to a diskette or other medium using a backup utility before proceeding. Samsung is NOT responsible for any data loss. You MUST, however reinstall all of your applications and drivers using the A Software CD and other application software as required. 74 Users Manual ol e

@ Taurus (Windows XP) - English.fm Page 75 Thursday, March 28, 2002 6:06 PM @ 1]

\l@

1. Restart your computer 2. Open the CD Drawer and insert the Recovery CD. Close the drawer. 3. You will see a message Press any key to boot from the CD, press any key. 4. You will be presented with the User Installation Option. iy If the Recovery Menu does not appear, proceed as follows:

If your computer cannot boot from the CD, change the boot priority to the CD-ROM device as described in this manual. Troubleshooting 75 en ma Ft e| |@

Taurus (Windows XP) - English.fm Page 76 Thursday, March 28, 2002 6:06 PM Specifications Dimension LCD viewing area (14.1" TFT) 285.6 x 214.3 mm Width 32.0 cm Depth 26.5 cm Height 2.95 cm Weight (CD Drive, Li-lon battery & 14.1 TFT LCD) 2400 g Environment Imbienttomperatre, operating SSCS Ambient temperature, storage -32_60 C Relative humidity (noncondensing), operating 30-80%

Relative humidity (noncondensing), storage 95%

Altitude, operating 0 to 4,572 m Altitude, storage 0 to 13,716 m Shock, operating 122 G for 2 ms half sine Shock, nonoperating 163 G for 2 ms half sine Lithium-lon Smart Battery Nomawegh ag Nominal open circuit voltage 14.8 VDC Capacity, typical 4400 mAhr, 65.0whr Charging time, approximate, with computer turned off, typical. 3.0 hr Charging time, approximate, with computer tumed on, typical 6.0 hr External AC Adapter peatngvalage ST OVAGSSSSSS Line frequency 50-60 Hz Input current 1.5A 100 V~0.8A 240 V Output current 4.2A Output voltage 19.0 VDC 76 Users Manual

@||e

~ Taurus (Windows XP) - English.fm Page 77 Thursday, March 28, 2002 6:06 PM @ :

Abbreviations

. Amperes AC........ Alternating current ACPI...... Advanced Configuration and Power management Interface APM ...... Advanced Power Management ATA....... AT attachment (refers to the hard-drive interface in an AT-

compatible computer) ATAPI..... AT attachment packet interface BBS....... Bulletin board system BIOS ...... Basic input/output system C Le... ae. Centigrade CD........ Compact disc CD-ROM .. Compact disc read-only memory cm ........ Centimeters COM...... Communication (as in communication port) CMOS..... Complementary metal-oxide semiconductor MC........ Direct current DMA...... Direct memory access DPMS ..... Display power-management signaling DRAM..... Dynamic random access memory DSTN ..... Double layer super twist nematic ECP....... Extended capabilities port EPP....... Enhanced parallel port Zeceeeeeeee gram

[ Ce Gravity GB........ Gigabytes br......... hour Hz........ Hertz IDE ....... Integrated drive electronics VO........ Input/output IRQ....... Interrupt request line Abbreviations 77 eo Fe et 4

Te 78 Users Manual

@ Taurus (Windows XP) - English.im Page 78 Thursday, March 28, 2002 6:06 PM ISA ....... Industry Standard Architecture KB........ Kilobytes kg......... Kilograms LAN....... Local-area network

| Pounds LBA....... Logical block addressing LCD....... Liquid-crystal display M......... Meters mA........ Milliampere mAhr...... Milliampere hour MB........ Megabyte mm ....... millimeter MPEG..... Motion Picture Experts Group MPU...... Microprocessor unit ms ........ Millisecond PDF ....... Portable document format PC........ Personal computer PCI ....... Peripheral component interconnect PCMCIA. . Personal Computer Memory Card International Association POST...... Power-on self-test PNP....... Plug and play PS/2....... Personal System/2 RAM ...... Random-access memory ROM...... Read-only memory SVGA ..... Super video graphics array TFT....... Thin-film transistor USB....... Universal serial bus rn Volt VAC ...... Voltage alternating current VCC ...... Voltage collector current VDC ...... Voltage direct current whr ....... Watt hour

: @ Taurus (Windows XP) - English.fm Page 79 Thursday, March 28, 2002 6:06 PM

Glossary AC adapter The AC (or alternating current) adapter regulates current coming into your computer from the wall outlet. The current at the wall outlet is alternating current and needs to be changed by the adapter to DC (direct current) before your computer can use it for power. ACPI ACPI (Advanced Configuration and Power Interface)- a method for describing hardware interfaces in terms abstract enough to allow flexible and innovative hardware implementations and concrete enough to allow shrink-wrap OS code to use such hardware interfaces. BIOS BIOS stands for basic input/output system. The BIOS is software (often called firmware) that is independent of any operating system. It enables the computer to communicate with the screen, keyboard, and other peripheral devices without using programs on the hard disk. The BIOS on your computer is flash BIOS, which means that it has been recorded on a flash memory chip that can be updated if needed. Boot To start your computer. A cold boot resets the entire computer and runs through all computer self-tests. A warm boot clears out computer memory only. Boot disk A disk containing operating system programs required to start your computer. A boot disk can be a floppy disk, hard drive, or compact disc. Byte The basic unit of measure for computer memory. A charactersuch as a letter of the alphabetuses one byte of memory. Computer memory is often measured in kilobytes (1,024 bytes) or megabytes (1,048,576 bytes). Each byte is made up of eight bits. For more information on bytes and bits, see an introductory book on computers. Cache memory Cache is very fast, zero-wait-state memory located between the microprocessor and main memory. Cache reduces the average time required by the microprocessor to get the data it needs from the main memory by storing recently accessed data in the cache. Glossary 79

@ Taurus (Windows XP) - English.fm Page 80 Thursday, March 28, 2002 6:06 PM @

CardBus CardBus technology enables the computer to use 32-bit PC Cards. Hardware in the computer and the Windows operating system provide support for the 32-bit cards. The voltage of 32-bit cards (3.3 volts) is lower than that of 16-bit cards (S volts). The 32-bit cards can transmit more data at a time than the 16-bit cards, thus increasing their speed. CMOS memory CMOS (complementary metal oxide semiconductor) memory is powered by the CMOS battery. The System Setup settings and other parameters are maintained in CMOS memory. Even when you turn your computer off, the information in CMOS memory is saved. COM port COM stands for communication. COM ports are the serial ports in your computer. Compact Disc A compact dise (CD). Conventional memory The first 640 KB of system memory. Operating systems and application programs can directly access this memory without using memory-management software. Disk The device used by the computer to store and retrieve information. Disk can refer to a floppy disk, hard disk, or RAM disk. Disk cache A software device that accumulates copies of recently used disk sectors in RAM. The application program can then read these copies without accessing the disk. This, in turn, speeds up the performance of the application. A cache is a buffer for transferring disk sectors in and out of RAM. Data stored in a disk cache is a copy of data already stored on the physical disk. DMA (direct memory access) A method of transferring data from a device to memory without having the data pass through the microprocessor. Using DMA can speed up system performance. DPMS Display Power Management Signalling. Displays or monitors that comply with this can be managed by the Power Management features found in the system setup. Floppy disk A removable disk, also called floppy or diskette. 80 Users Manual 4

ha +

@ Taurus (Windows XP) - English.fm Page 81 Thursday, March 28, 2002 6:06 PM f Hard drive Also called fixed disk. A hard drive is connected to the computer and can be installed or removed. Data written to a hard drive remains until it is overwritten or corrupted. The 2.5-inch hard drive in your computer was designed for use in a notebook computer. Because hard drives in notebook computers are smaller than those in desktop computers, their maximum storage capacity may be less than that of desktop hard drives. However, because of their smaller size, the drives handle shock and vibration better than larger drives, which is important for a notebook computer. Vo Input/output. Refers to peripheral devices, such as printers, that are addressed through an I/O address. I/O address 1/O stands for input/output. Peripheral devices, such as printers, are addressed through the I/O port address. IRQ (interrupt request line) The IRQ is a hardware line that a device uses to signal the microprocessor when the device needs the microprocessors services. The number of IRQs is limited by industry standards. LCD (liquid-crystal display) The LCD screen on your computer differs from the display screen of a desktop monitor. Most desktop monitors use CRT (cathode-ray tube) displays, which work by moving an electron beam across phosphor dots on the back of the screen. The phosphor dots light up to show the image. LCDs use a liquid-crystal solution between two sheets of polarizing material. Electric current passing through the liquid aligns the crystals so that light can or cannot pass through them, creating an image. MB (megabyte) 1,024 kilobytes. Megabit 1,048,576 bits or about 128 kilobytes. Operating system A program that supervises the computer's operation, including handling 1/O. Application programs and users can request operating-system services. A user might request operation-system services to copy files or format a disk. An application program might use the operating system to obtain keyboard input, write data to a file, or write data to a screen. Glossary 81

@||e-

@ @ Taurus (Windows XP) - English.fm Page 82 Thursday, March 28, 2002 6:06 PM @ E PC Card PC Card stands for personal computer card. The Personal Computer Memory Card International Association (PCMCIA) defines the standards used to develop all PC Cards. PC Card types include: modems, Ethernet adapters, SCSI adapters, ATA cards, and memory cards. PC slot The PC slot is the hardware slot in the computer where the PC Card is placed. Pixel A pixel is an individual dot in a graphic displayed on your computer. The pixels are so close together that they look as though they are connected. An LCD screen displays thousands or millions of pixels. Plug and Play A plug and play operating system automatically configures computer components to work with your system. With this type of operating system, you normally do not need to set jumpers on devices or set memory addresses or IRQs. RAM (random access memory) The computer's system memory, including conventional and extended memory. You can write to and read from RAM. Information stored in RAM is temporary, and is erased when the system is turned off. Refresh rate The refresh rate is the rate at which the image on the LCD screen is rewritten to the screen. A fast refresh rate helps keep the image from flickering. Resolution The resolution is the sharpness or clarity of the image on your LCD screen. Resolution is measured by the number of pixels the computers screen can display. For example, a resolution of 800 x 600 means that the screen can display 800 pixels in row and can display 600 rows. The more pixels displayed, the higher the resolution and the better the image. ROM (read-only memory) Permanent computer memory dedicated to a particular function. For example, the instructions for starting the computer when you first turn on power are contained in ROM. You cannot write to ROM. (ROM is not the same as RAM). Sector Also known as disk sector. The portion of a track that is numbered and can hold a specified number of characters (usually 512 KB). 82 Users Manual

| @ Taurus (Windows XP) - English.fm Page 83 Thursday, March 28, 2002 6:06 PM Shadow RAM A write-protected area of RAM that contains a copy of the BIOS. As the computer boots, the BIOS is copied from its permanent location in ROM to RAM. The BIOS can be executed much faster in RAM than in ROM. The BIOS remains in shadow RAM until you turn off the computer. TFT (thin film transistor) LCD A TFT LCD uses a separate transistor circuit to control each pixel. This technology provides the best resolution for an LCD screen. A TFT LCD is also sometimes called an active matrix LCD. Zoomed video Zoomed video technology enables zoom video PC Card to transfer data directly from the card to video and audio systems without going through the microprocessor. This process improves video performance. Video conferencing and real-time multimedia devices, such as video cameras, are supported by zoom video. Glossary 83 9) e||@

@|\e-