SSA-R1000 SSA-R1100 RFID Reader user manual imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please visit our website. www.samsungsecurity.com safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING
To reduce the risk of re or electric shock, do not expose this appliance to rain or moisture. WARNING 1. Be sure to use only the standard adapter that is speci ed in the speci cation sheet. Using any other adapter could cause re, electrical shock, or damage to the product. Incorrectly connecting the power supply or replacing battery may cause explosion, re, electric shock, or damage to the product. Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or re. Securely plug the power cord into the power receptacle. Insecure connection may cause re. When installing the controller, fasten it securely and rmly. The fall of controller may cause personal injury. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers lled with water on top of the controller. Doing so may cause personal injury due to re, electric shock, or falling objects. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause re or electric shock. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause re or electric shock. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modi cations or attempted repair.) 10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause re or electric shock. CAUTION 1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference. Do not install in a location subject to high temperature (over 50C), low temperature (below -10C), or high humidity. Doing so may cause re or electric shock. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause re or damage to the product. 2. 3. 4. 5. 6. 7. 8. 9. 2. 3. 4. 2_ Safety information 5. 6. 7. 8. 9. Keep out of direct sunlight and heat radiation sources. It may cause re. Install it in a place with good ventilation. Avoid aiming the controller directly towards extremely bright objects such as sun. Apparatus shall not be exposed to dripping or splashing and no objects lled with liquids, such as vases, shall be placed on the apparatus. The Mains plug is used as a disconnect device and shall stay readily operable at any time. FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
1) 2) This device may not cause harmful interference, and This device must accept any interference received including interference that may cause undesired operation. Caution This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in ac-
cordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. S A F E T Y I N F O R M A T O N I IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including ampli ers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories speci ed by the manufacturer. Use only with cart, stand, tripod, bracket, or table speci ed by the manufacturer, or sold with the apparatus. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over. Refer all servicing to quali ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. EnglisEnglish _ 3 contents PRODUCT INTRODUCTION5 5 Features At a Glance 5 Whats included 6 7 Cable Color Scheme 7 Cable Selection INSTALLATION AND EXTERNAL CONNECTION8 Installation Precautions on installation 8 9 10 External Connection INITIALIZATION11 11 Basic Operations OUTPUT FORMAT12 12 WIEGAND Output TROUBLESHOOTING13 13 Troubleshooting PRODUCT SPECIFICATIONS14 14 Product Speci cations 4_ Contents product introduction FEATURES This product is an elegant-looking proximity reader which has the maximum read range of 10cm (4), can be easily installed on a metal doorframe or the wall. Basically, both R1000 and R1100 use the same module with epoxy molding, which guarantees operation in any weather and environment condition. The two different bezels of two models are compatible with each other, meaning one can be replaced with the other according to the wall condition or the applicable situation. Green and red LED indicators and the Piezo buzzer ensure reliable and accurate operations. 125KHz Proximity Reader PSK Modulation 26 bit Wiegand Control of External LED Indicators Control of External Buzzer Reverse Polarity Protection Weatherproof WHATS INCLUDED Check if the following items are included in the product package. Whats included in SSA-R1000 P R O D U C T I N T R O D U C T O N I
Bezel of SSA-R1000 READER Module 3.5 x 40 screws (x2) 3.5 x 25 screws (x2) 6 x 30 Plastic Anchors(x2) Whats included in SSA-R1100 Quick Guide CD Manual
Bezel of SSA-R1100 READER Module 3.5 x 40 screws (x2) 3.5 x 25 screws (x2) 6 x 30 Plastic Anchors(x2) Quick Guide CD Manual EnglisEnglish _ 5 product introduction AT A GLANCE Front/Rear 2 3 4 LED Buzzer Displays the system operation status using red and green indicators. Piezo buzzer. Connection Cable Used to connect to the power or I/O cable. Fixing Hole Fixing hole for wall-mounting. 6_ Product Introduction CABLE COLOR SCHEME Item Cable Color Signal Line Description Power Input Output Not used Red Black Blue Yellow Green White Orange DC +12V DC +12V supplied GND Earth-grounding for power Buzzer Control BUZZER Control Input Port LED Control LED Control Input Port Out Wiegand 0 Wiegand Data 0 Output Port Out Wiegand 1 Wiegand Data 1 Output Port NC Not Connected P R O D U C T I N T R O D U C T O N I CABLE SELECTION 1 2 Item Cable Type Cable Type Maximum Allowable Distance Maximum Allowable Distance Power (DC12V) Belden #9409, 18 AWG 2 Conductor, Unshielded Belden #9409, 18 AWG 2 Conductor, Unshielded Within 3m Within 3m WIEGAND Output Buzzer Control LED Control Belden #9512, 22 AWG 4 Conductor, Shielded Belden #9514, 22 AWG 8 Conductor, Shielded EnglisEnglish _ 7 installation and external connection INSTALLATION
- Inserted in the doorframe / attached to the wall 1. Two 6-32 or M3 holes are 3.3 (8.38 cm) away from each other vertically; between the two exists one 1/2 hole through which the reader cables are arranged. The midway hole is located 1.7 (4.31cm) down from the upper hole.
(If the product is already installed, you can skip this step.) Insert the reader cables to the midway hole and x the reader module with two 6-32 or M3 screws. Insert the reader module into the bezel and push it up until you hear a click. 2. 3. Upper 6-32 hole 1.7
(4.31cm) 3.3
(8.38cm) 1/2hole 6-32 hole Lower Reader Module 6-32 or M3 Screws 6-32 or M3 Screws Gang Box Reader Module Wall Mount Mullion Mount Bezel Bezel Electric Gang Box Mount 8_ Installation and External Connection PRECAUTIONS ON INSTALLATION If installing on a metal wall If you install the reader on a metal wall, the read range may be reduced. To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below. I I N S T A L L A T O N A N D E X T E R N A L C O N N E C T O N I Metal Wall Spacer Reader If installing more than one reader side by side or front and back If you install more than one reader side by side or front and back, the read range may be reduced. In this case, if you present a card to one reader, the other reader may recognize the same card, meaning both readers read the same card simultaneously. To avoid this problem, keep at least 20 cm of space between the two readers. Minimum 20cm
#Reader 2
#Reader 1 BACK TO BACK
<Front and Back>
INSTALLATION
#Reader 1 Minimum 20cm
#Reader 2
<Side by Side>
SIDE BY SIDE INSTALLATION EnglisEnglish _ 9 installation and external connection EXTERNAL CONNECTION Wiring Diagram CONTROLLER Buzzer Control In LED Control In Wiegand Data 0 Out Wiegand Data 1 Out PC SSA-R1000/SSA-R1100 Blue Yellow Green White Red Black DC +12V GND POWER Item Power Supply Unit Wiegand Connection LED Control Buzzer Control Cable Color Connect the DC+12V to the red line. Connect GND to the black line. Connect the green line of the product to the Wiegand D0 input port of the controller. Connect the white line of the product to the Wiegand D1 input port of the controller. To control the LED indicators, connect the yellow line to the output port (relay) of the controller. To control the built-in buzzer, connect the blue line to the output port (relay) of the controller. 10_ Installation and External Connection initialization BASIC OPERATIONS Initial State (when the power is supplied) When you apply power to the reader, it will sound a beep before entering Standby with the red indicator turned on . Using the card Present the card to the reader until you hear a beep and the red indicator turns green. When the reader has transferred the card data to the controller, it returns to Standby with the red indicator turned on and waits for reading the next card. C I I I I N T A L Z A T O N I a r d
LED Control You can control the LED indicator of the device at your preference. Connect the LED control input line (yellow) to the NO port of the controller relay output, and GND to the COM port. Set the I/O of the controller so that you can change the color of the LED indicators. While the LED control is working, the green indicator stays solid. This function not only enables you to change the color representing Standby from red to green, but it can be also applied to make various modi cations according to the different I/O settings of the controller. For more information about the I/O settings of the controller, refer to the user manual of the controller. Buzzer Control You can control the buzzer of the device at your preference. You can con gure the I/O settings of the controller so that it sounds a beep. While the buzzer control is working, the product keeps sounding the beep. The controller can use the I/O settings to set the buzzer control so that it sounds an additional beep for authorized or unauthorized access upon user authentication. Furthermore, you can make various modi cations according to the different I/O settings of the controller. For more information about the I/O settings of the controller, refer to the user manual of the controller. J Card reading is not available while the buzzer control is sounding the buzzer. EnglisEnglish _ 11 output format WIEGAND OUTPUT Timing Diagram 100us DATA-0 1ms DATA-1 LOGIC 1 0 2 1 3 1 n-2 1 n-1 0 n 0 5V 0V 5V 0V
*n : 26 Data Type Bit 1 : Even Parity (bit 2 ~ bit 13) Bit 2 ~ 9 : Facility Code (000 ~ 255) Bit 10 ~ 25 : ID Number (00000 ~ 65,535) Bit 26 : Odd Parity (bit 14 ~ bit 25) 12_ Output Format troubleshooting TROUBLESHOOTING If the product does not function properly, please see the below for trouble shooting. If the trouble persists, please contact the SAMSUNG Customer Service near you. PROBLEM My card is not read properly. When I turn on the product, it sounds a beep with dimly turned on indicator. SOLUTION 1) 2) 3) 1) 2) 3) Check the rated voltage speci ed in the user manual and the catalog. Ensure that the card must comply with the PSK (125 KHz Proximity ) format provided by Samsung. Cards of 125 kHz purchased from other manufacturers may not be supported. If the problem persists, contact the nearest customer service for your assistance. Ensure that you are using a larger-capacity adaptor than speci ed in the user manual or the catalog, which should cover the rated current consumption of the reader. If you are using multiple readers that are connected to one adaptor, make sure that the adaptor should be large enough to cover the current consumption multiplied by the reader count. Even with a large adaptor enough to supply adequate power, if the power cable is not a dedicated line (such as communication line or UPT cable), or if its so long to cause power loss, youd better replace it with a dedicated line or reinforce it. If the problem persists, contact the nearest customer service for your assistance. T R O U B L E S H O O T N G I EnglisEnglish _ 13 product speci cations PRODUCT SPECIFICATIONS Item SSA-R1000 SSA-R1100 Power / Current DC 12V / Max.120mA Reading Time (Card) 30ms Input Port Output Port 2ea : External LED Control, External Buzzer Control 26bit Wiegand LED Indicator 2 Color LED (Red and Green) Beeper Piezo Buzzer Operating Temperature
-30C to +50C Operating Humidity 10% to 90% relative humidity non-condensing Color / Material Dimension
(W x H x D(mm)) Weight RF Speci cations Silver with Black/ Polycarbonate 47.0 x 122.0 x 26.0 75.3 x 122.0 x 26.0 150g 130g Frequency : 125KHz Modulation : PSK No. of Channels : 1CH Output : Less than 65.80dBuA/m at a distance of 10m 14_ product speci cations Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.) This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment. To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.