SSA-R2000 RFID Reader user manual imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please visit our website. www.samsungsecurity.com safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING
To reduce the risk of re or electric shock, do not expose this appliance to rain or moisture. WARNING 1. Be sure to use only the standard adapter that is speci ed in the speci cation sheet. Using any other adapter could cause re, electrical shock, or damage to the product. Incorrectly connecting the power supply or replacing battery may cause explosion, re, electric shock, or damage to the product. Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or re. Securely plug the power cord into the power receptacle. Insecure connection may cause re. When installing the controller, fasten it securely and rmly. The fall of controller may cause personal injury. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers lled with water on top of the controller. Doing so may cause personal injury due to re, electric shock, or falling objects. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause re or electric shock. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause re or electric shock. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modi cations or attempted repair.)
. When cleaning, do not spray water directly onto parts of the product. Doing so may cause re or electric shock. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference. Do not install in a location subject to high temperature (over 50C), low temperature (below -10C), or high humidity. Doing so may cause re or electric shock. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause re or damage to the product. 2_ Safety information 2. 3. 4. 5. 6. 7. 8. 9. 2. 3. 4. 10. CAUTION 1. 5. 6. 7. 8. 9. Keep out of direct sunlight and heat radiation sources. It may cause re. Install it in a place with good ventilation. Avoid aiming the controller directly towards extremely bright objects such as sun. Apparatus shall not be exposed to dripping or splashing and no objects lled with liquids, such as vases, shall be placed on the apparatus. The Mains plug is used as a disconnect device and shall stay readily operable at any time. FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
1) 2) This device may not cause harmful interference, and This device must accept any interference received including interference that may cause undesired operation. Caution This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in ac-
cordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. S A F E T Y I N F O R M A T O N I IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including ampli ers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories speci ed by the manufacturer. Use only with cart, stand, tripod, bracket, or table speci ed by the manufacturer, or sold with the apparatus. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over. Refer all servicing to quali ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. English3 contents PRODUCT INTRODUCTION5 5 Features At a Glance 5 Whats included 6 7 Cable Color Scheme 7 Cable Selection INSTALLATION AND EXTERNAL Installation Precautions on installation 8 9 10 External Connection CONNECTION8 INITIALIZATION11 11 Output Format OUTPUT FORMAT13 13 WIEGAND Output 12 Basic Operations 14 4/8 BIT BURST Output Format TROUBLESHOOTING15 15 Troubleshooting PRODUCT SPECIFICATIONS16 16 Product Speci cations 4_ contents product introduction FEATURES This product is an elegant-looking proximity reader equipped with the built-in keypad, which has the maximum of 10 cm (4) read range. It is also supported by backlighting on the keypad, enabling stable operation at night. This product permits user access through authentication of the presented proximity card and personal identi cation number using the keypad. Red, green and orange LED indicators and the Piezo buzzer ensure reliable and accurate operation. 125 KHz Proximity / PIN Reader PSK Modulation 26 bit Wiegand Data Output 4/8 Bit Burst Output Format supported Numeric Keypad with Backlighting for Night Operation Control of External LED Indicators Control of External Buzzer Tamper Switch Reverse Polarity Protection P R O D U C T I N T R O D U C T O N I WHATS INCLUDED Check if the following items are included in the product package.
Product Rear Panel O-ring (x5) 3.5 x 40mm Screws (x4) 3.5 x 12mm Screws (x4) 6 x 30mm Plastic Anchor (x4) Cable (x3) CD Manual
Quick Guide English5 product introduction AT A GLANCE Front/Rear
6 5 4 3 7 8 1 LED 2 Keypad 3 2-PIN Connector 4 6-PIN Connector 5 8-PIN Connector Displays the status of the system operation. Used to enter the ID/password. Can be connected to the power cable. Can be connected to Wiegand cables. Connected to the tamper, LED and buzzer control connection cables. 6 Output Selection Switch Switch that allows you to select an output from 8 bit, 4 bit Burst and Wiegand. 7 Tamper Switch 8 Fixing Screw Tamper switch. Screws for xing the devices. 6_ product introduction P R O D U C T I N T R O D U C T O N I CABLE COLOR SCHEME 2-PIN Connector I/O Pins Signal Cable Color Power (+12V) Earth-grounding 6-PIN Connector I/O Pins Wiegand Data Output 0 Wiegand Data Output 1 Not Used Not Used 8-PIN Connector DC +12V GND (-) WIK_DATA0 WIK_DATA1 Not Used Not Used Red Black Signal Cable Color Green White Orange Brown I/O Pins Signal Cable Color Tamper Switch NC Tamper Switch COM LED Control LED Control LED Control Buzzer Control Not Used Not Used Tamper NC Tamper COM Red LED Control Green LED Control Orange LED Control BUZZER Control Not Used Not Used Green with White Stripes Gray White with Red Stripes Yellow Blue with White Stripes Blue Pink Sky Blue CABLE SELECTION Item 1 2 Power (DC12V) Card/PIN data (Wiegand) Control Signal (LED,BUZZER) TAMPER Cable Type Belden #9409, 18 AWG 2 Conductor, Unshielded (Maximum Allowable Distance : Within 3m) Belden #9512, 22 AWG 4 Conductor, Shielded Belden #9514, 22 AWG 8 Conductor, Shielded English7 installation and external connection INSTALLATION 1. 2. 3. 4. Attach the provided rear panel to the wall and drill two 6-32 holes and one 1/2 inch hole on it.
(See [Figure 1]) Refer to [Figure 2] below on how to secure the rear panel to the wall using the provided screws. Apply each of 5 O-rings to the corresponding point as shown in [Figure 2]. Fix the main unit with the rear panel by inserting the main units cables into the center hole and pushing the main unit towards the rear panel. O-ring O-ring O-ring 6-32 hole O-ring 1/2 hole 6-32 hole O-ring
) m m 5
. 9 3
5 5
. 1
) m m 5
. 5 4
9 7
. 1
) m m 7 4
5 8
. 1
) m m 2 5
5 0
. 2 1.52"(38.5mm) 1.52"(38.5mm) 3.03"(77mm)
[Figure 1]
[Figure 2]
J Once the main unit is xed with the rear panel, it will not be loosened. Please check if the device is operating properly before xing it. If you try to remove the rear panel once it is xed, the lock parts of the rear panel will break, resulting in a situation where the whole rear panel must be replaced. 8_ installation and external connection I I N S T A L L A T O N A N D E X T E R N A L C O N N E C T O N I PRECAUTIONS ON INSTALLATION IF INSTALLING ON A METAL WALL If you install the reader on a metal wall, the read range may be reduced. To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below. Metal Wall
Reader Spacer IF INSTALLING MORE THAN ONE READER SIDE BY SIDE OR FRONT AND BACK If you install more than one reader side by side or front and back, the read range may be reduced. In this case, if you present a card to one reader, the other reader may recognize the same card, meaning both readers read the same card simultaneously. To avoid this problem, keep at least 20 cm of space between the two readers. Minimum 20cm
#Reader 1
#Reader 2 BACK TO BACK
<Front and Back>
INSTALLATION
#Reader 1 Minimum 20cm
#Reader 2 SIDE BY SIDE
<Side by Side>
INSTALLATION English9 installation and external connection EXTERNAL CONNECTION WIRING DIAGRAM Wiegand Data 0 Out Wiegand Data 1 Out Green White Tamper Switch Out(NC) Green with white stripes Tamper Switch Out(COM) CONTROLLER Buzzer Control In Gray Blue LED Control In(Red) White with red stripes LED Control In(Green) LED Control In(Orange) Yellow SSA-R2000
Blue with white stripes
Red Black DC +12V GND POWER Cable Color Category Power Supply Unit Wiegand Connection LED Control Buzzer Control Tamper Control Connect the DC+12V to the red line. Connect GND to the black line. Connect the green line of the product to the Wiegand D0 input port of the controller. Connect the white line of the product to the Wiegand D1 input port of the controller. Enables you to turn on or off the LED indicators. To control green indicator, connect the yellow line to the controllers output (relay). Connect the blue with white stripes to control the orange indicator, connect the white with red stripes to control the red indicator.
(see page 12) Enables you to turn on or off the buzzer. To control the buzzer, connect the blue line to the controllers output (relay). (see page 12) Connect the COM port (gray line) of the products tamper switch to GND; connect the NC port (green with white stripe) of the tamper switch to the input port of the controller. 10_ installation and external connection I I I I N T A L Z A T O N I initialization OUTPUT FORMAT You can adjust the output format of the numeric values from the keypad. You can select 4/8 bit Burst or 26bit Wiegand. Adjust the format according to the controller receiving the keypad input. 1. To change the output format, use the switch on the rear of the product. 2. See the table below to make adjustment as needed. ON 1 2 Output Format SW #1 SW #2 Output Format of Card Output Format of Keypad ON ON OFF OFF ON OFF ON OFF 26bit Wiegand 26bit Wiegand 26bit Wiegand 26bit Wiegand 8bit Burst (Default) 26bit Wiegand 26bit Wiegand 4bit Burst M Switch #1 and #2 of SW are set to ON by default. Before you change the output format, you must disconnected the power. English11 initialization BASIC OPERATIONS Initial State (when the power is supplied) When you apply power to the product, it will sound beep three times before entering Standby with the red indicator turned on. Using the card Present the card to the product until you hear a beep and the green indicator turns on. The reader keeps the green indicator turned on while transferring the card data to the controller. When it is done, the green indicator turns off and for receiving the next card, the red indicator stays ON.
C
a
r d
Using the keypad Hold down the keypad until you hear a beep. The reader transfers the keypad data to the controller. If the output format of the keypad is 26-bit Wiegand, pressing any key of the keypad turns on orange indicator, and green indicator blinks when [ENT] is pressed after the input. The red indicator stays on after transferring data to the controller. By default, it is 8-bit burst. Hence, keypad input and pressing [ENT] will blink the green indicator only when you change the option to 26bit Wiegand. LED Control You can control the red, green and orange indicators as necessary. To control the red indicator, connect the red indicator control input line (white with red stripes) to the relay output NO port of the controller, and connect the GND line to the COM line. Set I/O of the controller; now you can control turning on/off the indicators. You can turn on/off the indicators according to the I/O settings of the controller, which can be applied to various situations. For more information about the I/O settings of the controller, refer to the user manual of the controller. Connect the yellow line for the green indicator, or the blue with white stripes for the orange indicator, to the COM port of the controller. Buzzer Control Connect the buzzer control input line (blue) to the NO port of the controller relay output, and GND to the COM port. You can con gure the I/O settings of the controller so that it beeps. If the product continues to beep, it means that the buzzer control is working properly. The controller can use the I/O settings to set the buzzer control so that it sounds an additional beep for authorized or unauthorized access upon user authentication. Furthermore, you can make various modi cations according to the different I/O settings of the controller. For more information about the I/O settings of the controller, refer to the user manual of the controller. Card reading is not available while the buzzer control is sounding the buzzer. Tamper Control You can set the signal that you want to output if the device is dismantled forcibly. Connect the COM port (gray line) of the products tamper switch to GND; connect the NC port (green with white stripe) of the tamper switch to the input port of the controller. If the tamper of the reader operates, the controller produces an input signal and generates the corresponding output depending on the controller setting. 12_ initialization output format WIEGAND OUTPUT Timing Diagram 100us DATA-0 1ms O U T P U T F O R M A T 5V 0V 5V 0V DATA-1 LOGIC 1 0 2 1 3 1 n-2 1 n-1 0 n *n : 34 or26 0 Data Type (26-bit) Bit 1 : Even Parity (bit 2 ~ bit 13) Bit 2 ~ 9 : Facility Code (000 ~ 255) Bit 10 ~ 25 : ID Number (00000 ~ 65,535) Bit 26 : Odd Parity (bit 14 ~ bit 25) English13 output format 4/8 BIT BURST OUTPUT FORMAT 4Bit Burst Output Format Keypads Binary Hexa Keypads Binary Hexa 0 1 2 3 4 5 0000 0001 0010 0011 0100 0101 0 1 2 3 4 5 6 7 8 9 ESC ENT 0110 0111 1000 1001 1010 1011 6 7 8 9 A B 8Bit Burst Output Format Keypads Binary Hexa Keypads Binary Hexa 0 1 2 3 4 5 11110000 11100001 11010010 11000011 10110100 10100101 F0 E1 D2 C3 B4 A5 6 7 8 9 ESC ENT 10010110 10000111 01111000 01101001 01011010 01001011 96 87 78 69 5A 4B 14_ output format T R O U B L E S H O O T N G I troubleshooting TROUBLESHOOTING If the product does not function properly, please see the below for trouble shooting. If the trouble persists, please contact the SAMSUNG Customer Service near you. PROBLEM My card is not read properly. When I turn on the product, it sounds a beep with dimly turned on indicator. The read range (R/R) of the card differs each time the product reads the card. SOLUTION 1) 2) Check the rated voltage speci ed in the user manual and the catalog. Ensure that the card must comply with the PSK (125KHz) format provided by Samsung.
- Cards of 13.56MHz format can not be used.
(Contact the card retailer regarding the card format.) 3) If the problem persists, contact the nearest customer service for your assistance. 1) 2) 3) 1) 2) Ensure that you are using a larger-capacity adaptor than speci ed in the user manual or the catalog, which should cover the rated current consumption of the reader. If you are using multiple readers that are connected to one adaptor, make sure that the adaptor should be large enough to cover the current consumption multiplied by the reader count. Even with a large adaptor enough to supply adequate power, if the power cable is not a dedicated line (such as communication line or UPT cable), or if its so long to cause power loss, youd better replace it with a dedicated line or reinforce it. If the problem persists, contact the nearest customer service for your assistance. The characteristics of a card are determined by the nature of the coils used and in the manufacturing process engaged by the card manufacturer. So what you do rst is to check that the cards in use are made by the same manufacturer. If you are using cards from different card makers, the read range (R/R) differs by the card, which is the result of normal operation. If you encounter a different read range for each card that is made by the same manufacturer, please contact the nearest customer service. English15 product speci cations PRODUCT SPECIFICATIONS Item SSA-R2000 Power / Current DC 12V / Max.95mA Reading Time (Card) 30ms Input Port Output Port LED Indicator Beeper Keypad 2 ea : External LED Control, External Buzzer Control 26bit Wiegand, 4/8bit Burst for PIN (Selectable) 3 LED Indicators (Red, Green and Orange) Piezo Buzzer 12 Key Numeric Keypad with Back Lighting Operating Temperature
-30C to +50C Operating Humidity 10% to 90% Relative Humidity Non-Condensing Color / Material Silver with Black/ Polycarbonate Dimension (W x H x D(mm)) 87.0 x 109.0 x 31.0 Weight RF Speci cations 160g Frequency : 125KHz Modulation : PSK No. of Channels : 1CH Output : Less than 65.80dBuA/m at a distance of 10m 16_ English Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.) This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment. To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system. AB82-02555A