SCOPE2.0 Plus User Manual
(GIS-PAMSC3) V0.1 SCOPE2.0 Plus User Manual
[ Revision History ]
Version Date Change History V0.1 2016.11.13 Draft V0.2 2017.02.02 Add SCOPE2.0Plus author Confirmed by Sangho Lee Sangho Lee inho.won inho.won 1 SCOPE2.0 Plus User Manual 1. Introduction SCOPE2.0 Plus is a device for transferring vibration signal and equipment information to an agent PC through wired/wireless communication. Users are advised to read carefully all manuals provided with the package, to ensure safe and efficient use of SCOPE2.0 Plus unit. This manual explains necessary skills and information for setting up and using SCOPE2.0 Plus 2 SCOPE2.0 Plus User Manual 2. SCOPE2.0 Plus Specification SCOPE2.0 Plus Platform comprise two boards(Main Board, Interface Board) and Sensor Module comprise one board. Each Board Contains following components 1) Board Components A. Platform i. Main Board : CPU / RAM / Flash / Power Module ii. Interface Board : WIFI / LAN B. Sensor Module i. Analog Vibration sensor interface Filter 2) Exterior This picture is of SCOPE2.0Plus Board and case. The front panel of SCOPE2.0 Plus has Power (24Vdc), USB OTG, LAN Port, RS-232 4Port, a Port of external antenna, LED. The rear panel of SCOPE2.0 Plus has FG. The Sid panel of SCOPE2.0 Plus has Sensor Connector (BNC) Figure 1 SCOPE2.0 Plus Exterior 3 SCOPE2.0 Plus User Manual Figure 2 SCOPE2.0 Plus Front Exterior A. Power : 24Vdc supply ( VCC / GND / FG) B. Antenna : Port for connecting WI-FI module C. LAN : LAN Port for Ethernet communication with other devices using TCP/IP D. USB : USB-OTG Port ( used for FW update) E. LED(1,2,3) : Status LED F. FG : Frame Ground for noise reduction. Connects to host equipment ground G. RS232 : standard for serial communication transmission of data ( used for communication between SCOPE2.0 Plus and equipment) H. Debug : RS232 Debugging Port 4 SCOPE2.0 Plus User Manual 3) H/W Specification A. SCOPE2.0 Plus internal H/W has following characteristics i. Freescale i.MX6 Qual Core(1 4) ii. Dual Band WIFI, 802.11 a/b/g, LAN communication support iii. FPGA(SPARTAN LX4 )support B. Platform HW Details ITEM CPU ETHERNET SERIAL USB WIFI SPECIFICATION Freescale-i.MX6Q CPU(Quad) 100M LAN USB to SERIAL Debug port USB2.0 Client Debug port 802.11a/b/g ADC BOARD I/F 8bit Bus, 5V, 3.3V, 24V supply INDICATOR Digital I/F 3COLOR x2 RS-232 x 4 CONFIG SWITCH TACT SWITCH x 1 FPGA I/F 8bit Bus FPGA PROGRAMMING SPI 20MHz 1CH SUPPLY POWER 24V (21.6V~26.4V) Size 100 x 60 x 40 (mm) 5 SCOPE2.0 Plus User Manual C. Analog Vibration sensor module Details ITEM FPGA ADC FILTER INPUT SUPPLY POWER (1) SUPPLY POWER (2) SUPPLY POWER (3) Connector SPECIFICATION SPARTAN-6 AD7684 x 4 IEPE(3MHz) 5V 3.3V 5V 24V BNC x 4 6 SCOPE2.0 Plus User Manual 3. How to install and Use 1) SCOPE2.0 Plus installations 2) SCOPE2.0 Plus Connection Check A. Change IP Address for Data PC to 192.168.0.5 B. Power On and confirm LED2 blinking green. 7 SCOPE2.0 Plus User Manual C. Do a ping test to SCOPE2.0 Plus from Data PC to confirm connection 8 SCOPE2.0 Plus User Manual 3) SCOPE2.0 Plus Pin Map A. Power Pin Num Description 1 2 3 VCC GND FG B. LAN Port Pin Num Description 1 2 3 4 Tx+
Tx-
Rx+
Rx-
C. RS-232 4Port Pin Num Description Pin Num Description 1 3 5 7 9 Ch1 Tx Ch1 Rx Ch1 GND Ch2 Tx Ch2 Rx 11 Ch2 GND 2 4 6 8 10 12 Ch3 Tx Ch3 Rx Ch3 GND Ch4 Tx Ch4 Rx Ch4 GND 9 SCOPE2.0 Plus User Manual 4. HW Specifications 10 SCOPE2.0 Plus User Manual Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
-
-
-
-
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio, TV technical for help.
- Only shielded interface cable should be used. Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment. 11 SCOPE2.0 Plus User Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device is operation in 5.15 5.25 GHz frequency range, then restricted in indoor use only. RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. 12 SCOPE2.0 Plus User Manual
[ Cable specification]
. Power Cable
- A ferrite Core is added to the Power input terminal(Number of turns / 1 turn)
( Using Power Source including a ferrite Core)
. LAN Cable(Using Direct Cable)
- Apply Shielded LAN Cable
- Add Ferrite Core on both end of LAN Cable ( Each Number of turns / 1turn) 13 SCOPE2.0 Plus User Manual
. RS-232 Cable(4Port)
- Apply Shielded Cable.
( Shield is connected to Frame Ground of SCOPE2.0 Plus) 14