en CD-R/RW DRIVE SCW-231) Users Guide - ENGLISH http : /www. samsung). electronics. com.
| BG68-10024A RU WSR ate AT AE ES The following diagrams illustrate the precautions to be taken when using your CD-RIRW drive. oh ous nN ctae You must not use the drive in any manner other than that specifiec' in this guide. eo CAUTION Do not attempt ta repair the CD-R/RW drive yourself. Contact your dealer or local SAMSUNG representative for all repai +, Use of controls or adjustments or performance of | soccdures other than those specified here In may result in hazardous radiation exposure.
| 4]
5 Yo reduce the risk of fire or electric shock, do not expose this appliance to cain or :
moisture. 4 WARRANTY Please reter to the Samsung limited warranty st utements. C F L\
eee ee Oe ee meme te 1 Detail COLE TEA re EEE az |
| Front View of the CD-R/RW Drive | [Re Headphone Connector The audio output connector enables you to plug stereo headphones into the
drive. It requires a 3.6mm stereo mini-jack. 2 Volume Control Dial This control dial adjusts the volume for your headphones. You can only use the headphone jack and volume control when you have installed the required software utilities. For example, the Microsoft Windows Media player can be used.
3 Writing LED When you write data in the disc.(Blink:Test mode, On: Writ 3 mode) 4 Reading/Disc In LED When you play a disc or when you place a disc in the tray
: h 5 Disc Tray 3 1 The Disc Tray opens and closes automatically when you press the Open/Close fi button.
@ When you place a disc in the tray, make sure that the |:.hel on the disc is facing upwards. If you are not loading or unloading a disc, the disc tray should remain closed. BA 6 Open/Close-Button Press open/close key. VEN Details for each parameter are listed below. I vr.
| Rear View of the CD-R/RW Drive |
Audio Output Connector You can connect a sound card to your drive using this foui-2in connector. This function is not covered in datail in this quide. Rafer to the documentation supplied with your sound card. Device Configuration Jumper Usually, this is a pre-set configuration as illustrated below:
can Verify that the setting is as illustrated. If it is not, simply remove the jumper and place it in the correct position. 3 Host IDE Interface Connector This input/output interface connector is used to connect tte 40-pin flat cable from the IDE interface to the CD-R/AW drive. 4 Power Connector The power connector is a four-conductor male plug. L\
[ We eLuwtonnt Mw A The eS eee . |
aon Cho / RW aah Eng Bs/en sak seas rhe *
| System Requirements |
Before you install the CD-R/RW drive, we strongly recommend that you make certain
(hat your set-up meets the system requirements listed below. smceyu emsemnctaeaNnc mma ane AEE NN HAT Item Descriptian sny Type of computer Pentium z(or higher) with an HE interface ARAM 16MB RAM(or higher) -
Hard drive 528MB higher(Transfer Rate 800KBsec higher Access, Time 20m/sec Lower) 7 MS-00S 5.0(or higher) TIP:For MS-DOS, The CD-R/RW dei #3 can only Read a disc without Premaster Software Windows Microsoft Windows 95 or Windows NT 4.0*
emcee TIP:For Windows NT, we recomme 14 Service Pack2, Version 4.00.1381. eam ea casein
| Installing the CD-R/RW Drive |
Install the CD-R/RW drive in your computer horizontally, making str: that the Open/Close button is on the right. To install the drive, proceed as follows. 1 2 3 4 5 6 Turn OFF your computer. Ramember to verity the configuration jumper on the rear of the CD-R/RW drive. Remove the cover of your PC(main unit of the computer). Remove the blank cover panel of the 6.25 inch unit in which the CD-A/RW drive is to be installed. Connect the CD-R/AW drive to the IDE interface and power cables located inside your computer. Connectors are keyed so jt is impossible to put them in an incorrect position. Do not force the connectors, if they do nat seem ta fit. Install the CD-R/RW drive into the unit and secure it wyh mounting screws (recommended standard Mgn&f- 3%. @ %
@ Depending on your PC model, you may need to attach 6 guide rails to the drive, so that the drive is held firmly in place. On the ground that the guide rails are parts of tha computer, if you don't have these, please purchase separately.
@ if you use screws that are longer than the recommended standard, you may damage the driva. Put the cover back on your PC. ALI Ab. AM Psa MU. |
Hr fw SCW aa Buel NA eA R eee BOO Ba f 3 Technical Specifications |
SAMSUNG continually strives to improve its products. Both the design specifications and these user instructions are thus subject to change without notice. SECTIONS SCW-530 CD-DA, CD-ROM Mode-1, CD F:OM XA Mode-2 Form-1, Reading Disc Types Form-2, Photo-CD (Single. Mu | 3ession), Video CD ready, CD-Plus, CO-Extra, Enhanced CD, CO-VFMV DISC [Writing Disc kinds CD-R, CD-RW . Erasing Disc Kind cO-RW _ Disc Diameter 12 cm or 8 om 900kb/s (MAX) PIO Mode 3, DMA Moda 4 Access Time (1/3 stroke) | 350ms (Typical) DRIVEPERFOR- | Data Buffer Capacity 1MB MANCE Semicanductor Laser eae Not SpindlalMotar Brushless Motor -
Loading Mechanism Tray, DC motor(Soft Eject) Disc At Once, Session A. Ince, Track At Once, Variable Packet Writing, Fixed Packet Writing ERROR RATE Mode 1: 1 block/10', Ncde 2: 1 block/10"
Eject Button Auto Ejact or Auto Inject Green Indicator(LED) Busy or Place a Disc ir ihe tray Red Indicator(LED) Writing a Disc (CD-R o 30-RW Disc) Headphone Output Stereo Mini-jack(@3.6m r)0.60420%(Vrms)33Q wheel Type Required Power Interface Connector ATAPI (EIDE) 7 Audio Output Lina out 0.70 #20% (Vrms), 47k&
Jumper Block Device Configuration J nper(MOLEX 70203) OPERATING Work Area Temperature : 5~45C, Humidity : 8-80%
ENVIRONMENT Temperature ; -40-60'2, Humidity . 5-90%
GENERAL Dimensions 146(W) x 41.5 (H) x 20(I2}mm (Including Bezel) a 1000 g RELIABILITY 00,000 POH (Duty 25 257 _
~ a Loading | 30,000 times Data Transfer Rate WRITING METHOD FRONT PANEL
+5VDC 1.6A, +12VDC 3. 4A (MAX). REAR PANEL Che eee You r Chi Yous