FCC ID: A3LCCAR210R Wi-Fi/BLE combo module

User manual of CCAR210R

1. Introduction

CCAR210R is a Wi-Fi/BLE combo module compliant with IEEE802.11 b.g.n MAC (2.4GHz) and

Bluetooth Low Energy (BLE5.0) optimized for low-power applications.

The core chipset is from Realtek, part number SDA8700CSM.

2. Hardware Architecture:

Vendor

Realtek

Part Number

SDA8700CSM

2.1 Main Chipset Information

Item

IEEE802.11 b.g.n(2.4GHz)

BLE5.0

Version 1.0

Samsung Electronics

page 1 of 6

3. Operational Description

CCAR210R is the 802.11b/g/n MAC Wi-Fi and Bluetooth Low Energy BLE combo Module that acts as

a communication controller for users of a wireless device to connect to SMART DEVICE

- Features

>IEEE 802.11 b/g/n (2.4GHz, 1x1)

>20MHz/ 40MHz up to MCS7 supported

>Low power Tx/Rx for short range application supported

>Low power beacon listen mode

>Very low power suspends mode (DLPS)

>BLE

>High power mode (8dbm, share the same PA with Wi-Fi)

>Internal co-existence mechanism between Wi-Fi and BT to share the same antenna

- Time base of the RF frequency

For IF and RF frequency, a crystal(40MHz) is a clock reference.

- Synthesizer

Synthesizer inside Transceiver. Internal voltage controlled oscillator (VCO) provides the desired LO

signal base on the phase-locked loop (PLL) with a relatively wide tuning range for this application.

Internal fractional nPLL allows support for a wide range of reference clock frequencies

- WIFI Transmission

Base-band data is modulated and upconverted to the 2.4GHz ISM band, respectively.

Base-band Processing (BBP) IC has DSSS (BPSK/QPSK/CCK) and OFDM

(BPSK/QPSK/16QAM/64QAM) modulation function, it provides transmission data rate are 1, 2, 5.5,

11Mbps on DSSS and 6, 12, 18, 24, 36, 48, 54 Mbps on OFDM. Digital data signal will be converted to

analog (TX IQ) signals through DAC in BBP IC, TX IQ pass through to low pass filter. TX I/Q signal

use direct conversion (zero-IF) architecture converter to generate carrier frequency signal. Transceiver

IC and internal PA magnify output power.

- WIFI Receiver

Reverse direction isolation of LNA inside Transceiver IC suppresses unwanted radiation. Then RF

signal will be directly down to IF signal (RX IQ) and high frequency spurious emissions are suppressed by

LPF. At last RX IQ signal will be demodulated digital data.

- BLE

The RADIO contains a 2.4 GHz radio receiver and a 2.4 GHz radio transmitter that is compatible with

1M/2Mbps Bluetooth® low energy mode.

Version 1.0

Samsung Electronics

page 2 of 6

DSSS:CCK,BPSK,QPSK for 802.11b

OFDM:BPSK,QPSK,16QAM,64QAM,256QAM for 802.11g,n

- Product Details

- WIFI

> Data Modulation

> Frequency Range 2400-2483.5MHz

- BLE

> Data Modulation GFSK

> Frequency Range 2400-2483.5MHz

- Operating Temperature

> -20 ~ +85℃

Version 1.0

Samsung Electronics

page 3 of 6

4. RF Exposure Statement

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20 cm between the radiator and

your body. This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

Industry Canada Radiation Exposure Statement(D claration d’ exposition anx radiations):

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20 cm between the radiator & your

body.

Cet quipement est conforme aux limites d’ exposition aux rayonnements IC tablies pour un environment

noncom tr I. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source

de rayonnement et votre corps.

Version 1.0

Samsung Electronics

page 4 of 6

5. Notice

FCC Statement

Approval Statement

CE Statement

Hereby, we declare that this device is in compliance with the essential requirements and other relevant provisions of

directive 1999/5/EC.

FCC approval

This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesirable operation.

To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.

Contains Transmitter module FCC ID: A3LCCAR210R

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/ TV technician for help.

-The OEM integrator is responsible for ensuring the end-user has no manual instruction to remove or install module.

-The module is limited to installation in mobile or fixed applications.

IC approval

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two

conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the

device.

Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est soumise aux

deux conditions suivantes:

(1) cet appareil ne peut causer d'interférences, et

(2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais

fonctionnement de l'appareil.

The host device must be labeled to display the Industry Canada certification number of the module.

Contains transmitter module IC:649E-CCAR210R

Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada du module.

Contient module émetteur IC :649E-CCAR210R

Samsung Electronics

page 5 of 6

Version 1.0

IMPORTANT NOTE

This device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This device

should be installed and must not be co-located or operating in conjunction with any other antenna or transmitter.

This device is intended only for OEM integrators under the following conditions:

1) This module may not be co-located with any other transmitters or antennas.

2) The antenna must be installed such that 20cm is maintained between the antenna and users.

As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is

still responsible for testing their end-product for any additional compliance requirements with this module installed.

In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid

and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible

for re-evaluating the end product including this module and obtaining separate FCC & IC authorizations.

Cet appareil est conforme aux limites de la FCC et IC exposition aux radiations dans un environnement non contrôlé.

Cet appareil doit être installé et ne doit pas être co-localisées ou opérant en conjonction avec une autre antenne ou

un autre émetteur.

Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes :

1 ) L' antenne doit être installée de telle sorte que 20 cm est maintenue entre l'antenne et les utilisateurs .

2 ) Ce module ne peut pas être co-localisé avec d'autres émetteurs ou des antennes .

Aussi longtemps que deux conditions précitées sont remplies, le test du transmetteur supplémentaires ne seront

pas tenus. Toutefois, l'intégrateur OEM est toujours responsable de tester leurs produits finis pour toutes les

exigences de conformité supplémentaires avec ce module installé.

Dans le cas où ces conditions ne peuvent pas être remplies, alors la FCC et IC autorisations ne sont plus considérés

comme valides et l'ID de la FCC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur

OEM sera responsable de réévaluer le produit final, y compris l'obtention de ce module et séparée de la FCC et IC

Autorisations

User Information

Caution: Any changed or modifications not expressly approved by the party responsible for compliance could

void the user`s authority to operate this equipment.

Attention: Toute changé ou modifications non expressément approuvés par la partie responsable de la conformité

pourraient annuler l'utilisateur `autorité de faire fonctionner cet équipement.

Version 1.0

Samsung Electronics

page 6 of 6

CCAR210R PF1_ Label Label Design Information Size: 26.0 X 12.0 [mm]

Color: White(print: Black) MODEL: CCAR210R CMIIT ID:

FCC ID: A3LCCAR210R IC: 649E-CCAR210R ANATEL:

MOC:

4709-00XXXX Made in Korea SN:

DEVICE:

MAC(W):

MAC(B):

26mm 4-R1.0 R-C-SEC-CCAR210R 12mm Front of the module / Location of label

Samsung Electronics Co., LTD. 129, Samsu ng -ro , Yeongtong-gu Suwon-City, Gyeonggi-do, 16677, Korea Date: January 13, 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. UL Verification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern:

I, the undersigned, hereby authorize Ms. Chloe Lee/Manager of KCTL Inc. and hereafter referred to as KCTL to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Chloe Lee/Manager of KCTL Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing KCTL as our agent, we still recognize that we are responsible to:

comply with the relevant provisions of the certification program;

a) b) c) d) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) f) g) h) i) j) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Jenni Chun, General Manager Regulatory & Environmental Affairs Samsung Electronics America, Inc

Samsung Electronics Co., LTD. 129, Samsung -ro , Yeongtong-gu Suwon-City, Gyeonggi-do, 16677, Korea CONFIDENTIALITY REQUEST Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 January 13, 2021 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, Samsung Electronics Co., Ltd. requests confidentiality for the following products:

FCC ID Number A3LCCAR210R Product Title/Model Wi-Fi/BLE combo module / CCAR210R The following exhibits contain trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our product. This material is not customarily available to the general public and we request that it be withheld from public inspection. We request that the following information submitted be held permanent confidential treatment. We hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give temporary confidentiality of commercially sensitive information prior to product release. If you have any questions, please feel free to contact me at the address shown below. Permanent Confidential Request

-. Schematics

-. Block Diagram

-. Operational Description

-. Antenna specification Short-Term Confidential Request

-. External Photos

-. Internal Photos

-. Test set-up photo

-. User Manual Sincerely, Jenni Chun/ General manager

Applicant/Grantee FCC ID:

Samsung Electronics Co., Ltd. A3LCCAR210R Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Section 15.212 Modular Transmitters Single Modular Approval Requirements This module is shielded with a shield can. Y A DC-DC converter is configured for internal supply of the module. Connected to antenna with internal transmission line and matching. Y Y Y Y 1 2 3 4 5 OK OK The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between 6 Mark the FCC-ID certification number Y on the module label. the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available

(see Section 15.31(i)). The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: XYZMODEL1 or Contains FCC ID:

XYZMODEL1. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.

(B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains FCC certified transmitter module(s). Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the 7 Module usage manuals were provided. Y 8 application for equipment authorization. The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. For RF exposure requests, ensure that RF specs are entered and adhered to within the approval source provided to all users fo this module. Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured.