CEMF11G01G0101 User manual CEMF11G01G0101 User Manual GCT GDM7240R1 LTE Solution REV 0.1 Samsung Electro-Mechanics 2011-11-11 Summary This description presents the general specifications of CEMF11G01G0101 which designed for 3GPP LTE Band 13. 2011 Samsung Electro-Mechanics. All rights reserved The names of actual companies and products mentioned herein may be the trademarks of their respective owners. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means without the express written consent of Samsung Electro-Mechanics. This document is subject to change without notice. REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 1/8 CEMF11G01G0101 User Manual 1 Electrical Characteristics 1.1 Power Supply The CEMF11G01G0101 must be connected to a 3.3V power supply by PCI Express Mini Card Electromechanical Specification Revision 1.2 Compliant. Requirement type Value Power Supply 3.3V Voltage range 3.1 ~ 3.6V Maximum Current
(Max Power +23dBm) 850mA Table 1-1. Power Supply Requirements 1.2 General Characteristics Item LTE Remark Current consumption Typ. 180mA Radio Frequency Bandwidth Frequency Type Maximum Throughput Tx : 777 ~ 787MHz Rx : 746 ~ 756MHz 10MHz Earcfn DL : 100Mbps UL : 50Mbps Modulation Format DL : QPSK, 16QAM, 64QAM UL : QPSK, 16QAM Antenna Configuration 2 Rx Diversity Connect with PC, With Test JIG Band 13 DL : 5230 / UL : 23230 Category 3 1 Tx - Main 2 Rx Main, Diversity Table 1-2. General Characteristics REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 2/8 CEMF11G01G0101 User Manual 1.3 Storage Condition It needs proper condition for protecting the rust.
- Temperature : 0 ~ +50C
- Humidity : lower level recommended, 25% ~ 65%RH
- Max Storage Limit : Within 6 month form production REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 3/8 CEMF11G01G0101 User Manual 2 RF Specification 2.1 LTE Specification All measurements are made under nominal power supply and room temperature 25C unless specified. Test Item Min Typ Max Unit Maximum Output Power
+21.3
+19.3
+23
+25.7 dBm Remark No MPR With MPR Occupied Bandwidth 0
-30
-50
-80 10 MHz fOOB : 15 ~ 85KHz fOOB : 150 ~ 950KHz fOOB : 1.5 ~ 9.5MHz fOOB : 10.5 ~ 14.5MHz Freq Offset : 5MHz Freq Offset : 15MHz QPSK 16QAM
@ -95dBm dB dB dB
ppm dBc
dBm Main, Div
-16.5
-11.5
-11.5
-23.5
-30
-33
-36 17.5 12.5 0.1
-25 5
-26
-46
-76 0
-0.1
-999 0
-34
-54
-84 Table 2-1. LTE RF Specification Tx Spectrum Emission Mask ACLR_EUTRA ACLR_UTRA EVM Frequency Error IQ Offset Sensitivity RSSI Transmit Signal Quality Rx REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 4/8 CEMF11G01G0101 User Manual 2.2 Antenna Connection 2 RF Port : U.FL Connector Main ANT Connector : 1EA AUX ANT Connector : 1EA
- Main ANT Connector is sharing the Tx and Rx. Figure 2-1. Antenna Connector Mechanical Dimension Attaching an antenna to the CEMF11G01G0101 :
Use a Hirose U.FL connector (Part No. : U.FL-R-SMT, CL No. : 331-0471-0-10) to attach an antenna to a connection point on the CEMF11G01G0101. Match coaxial connections between the CEMF11G01G0101 and the antenna to 50 . Minimize RF cable losses between the CEMF11G01G0101 and the antenna to less than 0.5 dB. 2.3 Ground Connection Connecting the CEMF11G01G0101 to system ground :
Connect to system ground for preventing noise leakage. Connect with host connector, two mounting holes, and PCI express mini card connector. REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 5/8 CEMF11G01G0101 User Manual 3 Label Information 3.1 Module Label The Label contains Model Name, Product Code, FCC ID, IMEI and Serial Number. Figure 3-1. Module Label Information 3.1.1 S/N(Serial Number) Ex) S N F B 000001 S N Company S: Samsung Custom Model N : CEMF11G01G0101 F Year F:2011 G:2012 B Month 1~9:Jan~SEP A:OCT, B:Nov, C:Dec 000001 Serial No 000001 ~ FFFFFF
(HEX) Table 3-1. Serial Number Information REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 6/8 CEMF11G01G0101 User Manual 6 Safety Information 6.1 Certification FCC ID : E2XCEMF11G01G0101 Warning: Exposure to Radio Frequency Radiation The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during normal operation is minimized. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna should not be less than 20 cm during normal operation. The gain of the antenna for LTE band must not exceed 0 dBi. FCC Compliance Information This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received. Including interference that may cause undesired operation. 6.2 Caution Modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 7/8 CEMF11G01G0101 User Manual This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. d your body. For label requirement when transmitter module is installed in a host,
This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC.
the host shall have an additional permanent label referring to the enclosed module
Contains Transmitter Module FCC ID: REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 8/8