Delivering Excellence Quick Reference Guide For moderno.S Quick Reference Guide For Modular demodulator MDM-GCA1B1 Antenna connector (R-SMA) Model name. Connecter Communication Connection interface Power supply Connector Switch inside Power supply Dimensions (mm) LED Indicator LED indicator 1 TECHNICAL DATA Supported Mode Supported Band Port Connecter Data length Stop bit Communication speed Communication protocol Control command moderno.S GSM, GPRS 850/900/1800/1900 RS-232C D-SUB9#4-40male 7/8bit 1bit 1,200bps460.8kbps PPP, TCP/IP T command DC5V5%
100(W)63(D)25.6(H) except stick out partattachment lug DATALINKPWR/RSSI 1.Connector(RS-232C,D-SUB 9pin: male plug Pin no. Signal Line I/O I I O O I CD RxD TxD DTR GND DSR 9 8 7 6 1 2 3 4 5 6 5 4 3 2 1 7 8 9 RTS CTS RI O I I Signal Name Function Reception carrier search When telecommunication line becomes connection, it is ON. Received Data Transmitted Data Data Terminal Ready Data Set Ready Request To Send Clear To Send Ring Indicator Data from this device
ONDuring operation of this device OFF: Telecommunication line is disconnected.
ON: When device is ready to receive data. RING. Signal of message arrival searched 2.Antenna Connector (R-SMA) Nopin: Signal terminal No2 pin: SG Pin no. 1 2 Terminal name TRX SG Transmission and Reception Signal Contents Signal Ground 3. Power supply Connector 1 2 3 Pin no. 1 2 Terminal name VCC PWR Direction of a signal Reception signal Reception signal 3 SG
SG: Power OFF(3 seconds more), Explanation DC5.0 0.25V OPEN: Power ON Signal Ground 4. LED indicator DATA LNK PWR/RSSI DATA LINK PWR/RSSI Data in transmission / reception During communication Power on/ Received Signal Strength Indication, Received Signal Strength Indicator 2 5. Dip Switch Setting Dip switch changes a movement mode of this device and sets transmission rate. Be sure to shut off power supply before setting Dip switch. Default :It is setting in factory shipment basically (all OFF). Function Setting Dip Switch NO. Display: power/in communication / transmission in LED. Parity select Transmission rate setting Date bit select Stop bit select 9,600bps 19,200bps 15.2Kbps User setting 8bit 7bit 1bit 2bit Non parity O parity odd number even number Normal Through Protocol conversion Protocol conversion AT command Electric wave reception level Enable(ON) Communication mode 1 2 OFF OFF ON OFF OFF ON ON ON
3
4
5
6
- OFF
ON
- OFF
ON
- OFF OFF
- ON OFF
- OFF ON
- ON ON
7
- OFF OFF
- ON OFF
- OFF ON
- ON ON 8
9
ON 0
ON 1 2 3 4 5 6 7 8 9 0 6. The antenna Only the listed antenna here should be connected and operated together with the modem. Company Smarteq Wireless AB Model 1140.26RPSMA(m) 7. Minimum distance required (more than 30cm)
"The antenna of this equipment must be installed and operated with a minimum distance more than 30cm from testing person's body"
3 FUNCTION Communication mode 1) Through mode: User connects directly the device with a communication module without protocol conversion. 2) Protocol conversion mode Even if the device is without AT command, without TCP/IP function, network communication is enabled just to connect to moderno. 3) Protocol conversion AT command mode Even if the device is with AT command, without TCP/IP function, network communication is enabled just to connect to moderno. Electric wave reception level is displayed by LED Bar indicator. Level LED(Red) LINK OFF OFF ON ON ON PWR/RSSI OFF ON ON ON ON DATA OFF OFF OFF ON ON 0(out of Area) 1 2 3 4 Electric wave reception level 4 FUNCTION LED indication contents Operation status of this device can be monitored by LED. Operation Status Power on In updating of system setting In module search Communication failure with a module Module activation Failure of module activation Stand by normal
(Electric wave reception level 1-4) Out of the communication zone
(Electric wave reception level 0) Phone number is unidentified.
(Electric wave reception level 1-4) Phone number is unidentified.
(Electric wave reception level 0) PWR/RSSI ON ON ON
Blink ON ON ON Remarks on LED All Led: On Shift lighting from right to left, and versa vice All Led Blinks Shift lighting from right to left Shit lighting from Top to bottom, versa vice PWR/RSSI Led: ON Blink PWR/RSSI Led :Blink ON BLINK LINK Led: Blink PWR/RSSI:ON LINK Led: Blink PWR/RSSI:Blink DATA ON ON
ON Blink ON ON
LED LINK ON Blink
ON
Blink ON
ON
Blink Blink 5 FUNCTION Rear case Insertion guide of SIM (summing impact modulator card) 1) Take out two screws of the rear case. 2) Open the rear case, and insert SIM card. Confirm that SIM card is appropriately inserted at the designated position. 3) Set the rear case at appropriate position, and close it tightly with two screws. 6 FUNCTION Installation guide 1) Installation guide of the unit. Before installation, be sure to switch off the power of the device to be installed. a) Screw up the unit to the appropriate install position of the device. b) Install the unit to the device at least with 2 screws at diagonal positions
(Recommendation is 4 points) 2) Associate power supply connector and communication connector to the device to be installed Antenna cable Communication connector
(RS232C # 4-40) 3) Installation of antenna. Please install an antenna justly. Power supply connector 7 FUNCTION Activation guide 1. Power supply ON 2. Check the LED display whether "DATA, LINK, PWR/RSSI" indicates as following chart.
(Refer to the section "trouble diagnosis" except the below indicated cases) 3. Only PWR/RSS LED becomes ON when the unit becomes activated normally 4. The unit status becomes able for communication. (It could take a couple of ten seconds to reach this status) Explanation of LED indicators at the activation No LED LED state guide Indication guide DATA ON LINK PWR/RSSI ON ON All LED: On ON ON
ON
ON Blink
ON
Blink
Blink ON ON
Blink Blink ON DATA LED: ON , LINK LED: ON PWR/RSSI LED: Blink LINK LED: Blink Shift lighting from left to right and versa vice LINK LED: Blink, PWR/RSSI LED: Blink PWR/RSSI LED: Blink PWR/RSSI LED: ON 1 2 3 4 5 6 7 Power supply ON state. *This status could continue for a couple of ten seconds. Initialization of setting is completed.
(it starts in all the DIP switches ON) In updating system setting and construction In search for communication module. Acquiring status of the phone number Out of electric wave range / area Activated normally.
(Electric wave reception level 1-4) Shut down guide 1) Check if "LINK" of LED display does not turn on. 2) Please drop the power supply.
*Data could be destroyed or lost when power supply is dropped during the LED status shows "LINK to the network. 8 FUNCTION Trouble diagnosis The modern.S" is very accurate instrument. When you doubt no-go situation, execute again OFF / ON operation of the power switch of the "modern.S". If it does not return to normal actuation even after such OFF/ON trial, check and confirm according to the following list. Trouble diagnosis by LED indication State LED Trouble cause Repair guide Cannot communicate at power supply ON. DATA Blink LINK Blink PWR/RSSI Blink ON ON ON Repeatedly lighting from top to bottom, versa vice Abnormality of communication module Failure in activation of communication module.
Blink PWR/RSSI LED: Blink Phone number is unidentified.
(Electric wave reception level 0)
ON
PWR/RSSI LED: ON Abnormality in communication due to device connection There is a possibility of defect of the communication module. It could be a case that initialization mobile network is not actuated. Please confirm its contract status. If actuated, there could be a defect of communication module. Reception sensitivity of an antenna is the bad situation. Please confirm the situation of an antenna and the cable connecting situation. It could be communication abnormality with a connection device. Confirm setting of transmission rate (a baud rate) and the connecting situation of wiring. 9 esky
[Czech]
Dansk
[Danish]
Sanden Corporation tmto prohlauje, e tento MDM-GCA1B1 je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Undertegnede Sanden Corporation erklrer herved, at flgende udstyr MDM-GCA1B1 overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Deutsch Hiermit erklrt Sanden Corporatoion, dass sich das Gert MDM-GCA1B1 in bereinstimmung mit den grundlegenden
[German]
Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti Kesolevaga kinnitab Sanden Corporation seadme MDM-GCA1B1 vastavust direktiivi 1999/5/E phinuetele ja
[Estonian]
nimetatud direktiivist tulenevatele teistele asjakohastele stetele. English Hereby, Sanden Corporation, declares that this MDM-GCA1B1 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Espaol Por medio de la presente Sanden Corporation declara que el MDM-GCA1B1 cumple con los requisitos esenciales y
[Spanish]
cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Sanden Corporation MDM-GCA1B1
[Greek]
1999/5/. 10 Franais Par la prsente Sanden Corporation dclare que l'appareil MDM-GCA1B1 est conforme aux exigences essentielles et
[French]
aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano Con la presente Sanden Corporation dichiara che questo MDM-GCA1B1 conforme ai requisiti essenziali ed alle altre
[Italian]
disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski Ar o Sanden Corporation izgatavotja nosaukums] deklar, ka MDM-GCA1B1 atbilst Direktvas 1999/5/EK btiskajm
[Latvian]
prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi iuo Sanden Corporation deklaruoja, kad is MDM-GCA1B1 atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos
[Lithuanian]
nuostatas. Nederlands Hierbij verklaart Sanden Corporation dat het toestel MDM-GCA1B1 in overeenstemming is met de essentile eisen en
[Dutch]
de andere relevante bepalingen van richtlijn 1999/5/EG. Malti
[Maltese]
Hawnhekk, Sanden Corporation, jiddikjara li dan MDM-GCA1B1 jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar Alulrott, Sanden Corporation nyilatkozom, hogy a MDM-GCA1B1 megfelel a vonatkoz alapvet kvetelmnyeknek s
[Hungarian]
az 1999/5/EC irnyelv egyb elrsainak. 11 Polski [Polish] Niniejszym Sanden Corporation owiadcza, e MDM-GCA1B1 jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Portugus Sanden Corporation declara que este MDM-GCA1B1 est conforme com os requisitos essenciais e outras disposies
[Portuguese]
da Directiva 1999/5/CE. Slovensko Sanden Corporation izjavlja, da je ta MDM-GCA1B1 v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili
[Slovenian]
direktive 1999/5/ES. Slovensky Sanden Corporation tmto vyhlasuje, e MDM-GCA1B1 spa zkladn poiadavky a vetky prslun ustanovenia
[Slovak]
Smernice 1999/5/ES. Suomi
[Finnish]
Sanden Corporation vakuuttaa tten ett MDM-GCA1B1 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Svenska Hrmed intygar Sanden Corporation att denna MDM-GCA1B1 str I verensstmmelse med de vsentliga
[Swedish]
egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. 12 13 0560 FCC ID: FCC ID: XV7MDM-GCA1-100 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)this device may not cause harmful interference,and
(2)this device must accept any interference received, including interference that may cause undesired operation. CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER FORCOMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. Note: This equipment has been tested and found to comply with the limits for a ClassB Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interferenceto radio communications.However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. 14 CAUTION: This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. End user cannot modify this transmitter device. Any unauthorized modification made on the device could avoid the user's authority to operate this device. CAUTION: This device complies with FCC RF exposure requirement. A separation distance of at least 30 cm must be maintained between the antenna of this device and all persons. 15 SANDEN