Integrated Switched-Mode Regulator Integrated 150mA Battery Charger Integrated Microphone bias Integrated LED Driver Product Features:
Bluetooth Spec. V2.1+EDR Compliant Class 2 type Output Power Support HSP ,HFP, A2DP and AVRCP Profiles High-quality audio 95dB SNR on DAC playback CVC Support for echo and Noise reduction Support for 802.11 Co-existence Size: 21mm x 13.5 mm x 2.35mm Weight: 0.8g System Architecture Specifications:
Operating Frequency Band Bluetooth Specification Output Power Class Operating Voltage Audio Interface Dimension Specifications are subject to change without prior notice Product Specification BM160 Class 2 Multimedia Module CSR, BC57F687A05 Feb. 2012 Product Description:
The BM160 is base on BlueCore5-Multimedia ROM QFN chipset from leading Bluetooth chipset supplier Cambridge Silicon Radio. BM160 interfaces a Bluetooth radio, baseband, DSP, high-quality audio codec, SMPS, LDOs, a battery charger and external EEPROM memory. BlueTunes ROM QFN uses advanced DSP features for the latest stereo enhancements and to improve audio quality; including SBC and MP3 decoder, support for FastStream(low battery codec) and 5-band EQ. The module and device firmware is fully compliant with the Bluetooth specification v2.1+EDR Applications:
Hands-free Car Kit Stereo Headset AV Headphones Echo Cancellation High Performance Mono Headsets Wireless Speakers 2.4GHz ~ 2.48GHz unlicensed ISM band V2.1+EDR Class 2 1.8V or 3.3V Analogue 21mm (L) x 13.5 (W) mm x 2.35mm (H) Spec-BM160-V1.3 Page 1 of 7 www.sunitec.com.tw Product Specification Max
+85C
+6.5V Max
+70C 4.2V 6.0V Average TBD TBD TBD TBD TBD TBD TBD Bluetooth Spec
-70
-20 11 0
-30
-40
-9 Bluetooth Spec
-6 to +4
> 16
<1000
-20
-40 Min
-40C
-0.30V Min
-20C 2.7V 4.5V Units mA mA mA mA mA mA mA Typ
-90
-10 6
-6
-38
-45
-16 Typ 3 24 0.5 940
-36
-45 Max
-86
11 0
-30
-40
-9 Max
1000
-20
-40 Electrical Characteristics Absolute Maximum Rating Storage Temperature Supply Voltage, (V_CHG) Recommended Operating Conditions Operating Temperature Range Supply Voltage, (V_BAT) Supply Voltage, (V_CHG) Power Consumption SCO Connection HV3 (30ms interval sniff mode) SCO Connection HV1 ACL Data Transfer 115.2Kbps UART no traffic (Master) ACL Data Transfer 115.2Kbps UART no traffic (Slave) CODEC Microphone inputs and ADC/channel DAC and loudspeaker driver, no signal/channel Digital audio processing subsystem VBAT = 4.2V; f = 2.441GHz; T=20C RF Characteristics Receiver Sensitivity at 0.1% BER Maximum Receiver Signal C/I Co-Channel Adjacent Channel Selectivity C/I -1MHz 2nd Adjacent Channel Selectivity C/I -2MHz 3rd Adjacent Channel Selectivity C/I -3MHz Image Rejection C/I VBAT = 4.2V; f = 2.4441GHz; T=20C Transmitter RF Output Power RF Power Control Range RF Power Range Control Resolution 20dB Bandwidth for Modulated Carrier 2nd Adjacent Channel Power (+/- 2MHz) 3rd Adjacent Channel Power (+/- 3MHz) VBAT = 4.2V; f = 2.4441GHz; T=20C All specifications including pinouts and electrical specifications may be changed without prior notice Units dBm dBm dB dB dB dB dB Units dBm dB dB KHz dBm dBm Min
-20
Min 0 16
Spec-BM160-V1.3 Page 2 of 7 www.sunitec.com.tw Product Specification Pin Configurations NAME PIN NO. 1 2 3 AIO1 AIO0 RESET 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 GND PIO9 N/A PIO11 PIO12 PIO13 PIO14 N/A GND VDD VDD VDD_USB
+1V8 GND N/A N/A UART_RTS UART_CTS UART_RX UART_TX N/A N/A TEST_EN N/A SPI_CSB SPI_MISO SPI_CLK SPI_MOSI VRE_IN VDD_BAT GND VDD_CHG LED1 LED0 GND SPK_L_N SPK_L_P SPK_R_N SPK_R_P GND_S MIC_BIAS MIC_B_P MIC_B_N MIC_A_P MIC_A_N GND PIO0 PIO1 PIO2 PIO3 PIO4 PIO5 PIO6 PIO7 PIO8 GND RF-IN GND TYPE Bi-directional Bi-directional CMOS input with weak internal pull-up GND Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional GND Power Power Power Power GND CMOS Output CMOS Input CMOS Input CMOS Output CMOS Input CMOS Output CMOS Input CMOS Output Analogue Battery terminal +ve GND Charger input Open drain output Open drain output GND Analogue Analogue Analogue Analogue Analogue GND Analogue Analogue Analogue Analogue Analogue GND Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional GND RF GND FUNCTION Programmable input/output line Programmable input/output line Reset if low. Input debounced so must be low for >5ms to cause a reset Ground Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Ground 3.3V Supply Connect to 1V8 Positive Supply For UART/USB Port Connect to VDD
+1.8V Supply Ground UART Request To Send (Active Low) UART Clear To Send (Active Low) UART Data Input (Active High) UART Data Output (Active High) For test purposes only, Leave unconnected Chip Select For Synchronous Serial Interface (Active Low) Serial Peripheral Interface Data Output Serial Peripheral Interface Data Clock Serial Peripheral Interface Data Input Take high to enable switch-mode regulator Lithium ion/polymer battery positive terminal. Battery charger output and input to switch-mode regulator Ground Lithium ion/polymer battery charger input LED Driver LED Driver Ground Speaker output negative, left Speaker output positive, left Speaker output negative, right Speaker output positive, right Analogue Ground Microphone bias Microphone input positive, right Microphone input negative, right Microphone input positive, left Microphone input negative, left Ground Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Ground RF Interface Ground RE-MARK For 3.3V Version For 1.8V Version Spec-BM160-V1.3 Page 3 of 7 www.sunitec.com.tw Recommended Layout patterns:
Product Specification 1.AIO1 2.AIO0 3.RESET 4.GND 5.PIO9 6.N/A 6 NC 7.PIO11 8.PIO12 9.PIO13 10.PIO14 11.N/A 11 NC 12.GND 13 NC 13.VDD 14 NC 14.VDD_USB 15 +1V8 15.+1V8 16 GND 16.GND 17 NC 17.N/A 18 NC 18.N/A 19.UART_RTS 20.UART_CTS 21.UART_RX 22.UART_TX 23.N/A 24.N/A 25.TEST_EN 26.N/A 27.SPI_CSB 28.SPI_MISO 29.SPI_CLK 30.SPI_MOSI 31.VRE_IN 32.VDD_BAT 33.GND 34.VDD_CHG 35.LED1 36.LED0 37.GND 38.SPK_L_N 39.SPK_L_P 40.SPK_R_N 41.SPK_R_P 42.GND_S 43.MIC_BIAS 44.MIC_B_P 45.MIC_B_N 46.MIC_A_P 47.MIC_A_N 48.GND 49.PIO0 50.PIO1 51.PIO2 52.PIO3 53.PIO4 54.PIO5 55.PIO6 56.PIO7 57.PIO8 58.GND 59.RF 60 GND Spec-BM160-V1.3 Page 4 of 7 www.sunitec.com.tw Recommended Reflow Temperature Profile:
Product Specification Key features of the profile:
-Initial Ramp=1-2.5/sec to 175 equilibrium
-Equilibrium time=60 to 80 seconds
-Ramp to Maximum temperature (250)=3/sec Max
-Time above liquidus temperature(217): 45 - 90 seconds
-Device absolute maximum reflow temperature: 250 MAC Address:
Each Module has his MAC Address 001d df XXXXXX Concerning the dimension of the tabonly printing the last six letters of the LAP on the module. 13.0 mm xxxxxx 5.0 mm The tab code pastes style:
Spec-BM160-V1.3 Page 5 of 7 www.sunitec.com.tw QDL Certificate Product Specification Spec-BM160-V1.3 Page 6 of 7 www.sunitec.com.tw Ordering Information No Items 2 BlueTunes Module 3 BlueTunes Module Test Kit 4 Titan is Antenna Ordering Code (Class 2) BM160 BM160 TK 2010B4844-01 Product Specification Description Test kit to fit CSR Casira Kit GigaAnt 2.4GHz Swivel SMA Antenna Titanis Antenna Version V2.1+EDR, 26 July 2007 CS-122312-DSP1 23 Oct 2008 BM160S Test Kit Document References References Specifications of the Bluetooth System BlueTunes ROM QFN Data Sheet Document History Revision Draft V0.1 V1.0 V1.1 V1.2 V1.3 Date 2009-10-22 2009-11-30 2009-12-01 2009-12-02 2012-02-20 Official release Swap LED0 and LED1 Add BQB Certificate History Contact Information Sunitec Enterprise Co., Ltd. Head Office:
3F.,No.98-1,Mincyuan Rd Sindian City, Taipei County 231,Taiwan Tel: 886-2-82191696 Fax: 886-2-82191676 China Factory:
No.2,Qilin Road 2,Run Tang Ind., Dan-Keng Village Fu Ming Community, Guan-lan Town, BaoAn District, Shenzhen GuangDong China Tel: 86-755-29802983 Fax: 86-755-29802984 E-mail:sales@sunitec-cn.com & project@sunitec-cn.com http://www.sunitec-cn.com Spec-BM160-V1.3 Page 7 of 7 www.sunitec.com.tw FCC ID: BYG024 Model: BM160-CB1-SJ Notice: The user should not modify or change this equipment without written approval form SANGEAN ELECTRONICS INC. Modification could void authority to use this equipment. Label for end product must include Contains FCC ID: BYG024 or A RF transmitter inside, FCC ID: BYG024. FCC ID Label Graph:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note:
If the product is too small to make so many text labels, only need to indicate the FCC ID number on the label, but the above text will be printed in the manual or packaging box. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. No change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void users authority to operate the device. The module has been regulatory approved for integrations which meet the following conditions:
1. The radio integration is embedded 2. The antenna must be installed such that 20 cm is maintained between the antenna and users 3. The Type and Gain of the antenna selected for the integration of the external antenna must meet the requirements as detailed in section. Used outside of these conditions will trigger re-approval.