FCC ID: 2AQZU-18024 CEILING FAN REMOTE CONTROLLER

CEILING FAN REMOTE CONTROL MANUAL LEARNING PROCESS NOTEThe Hand Held Remote Control System is equipped with a learning frequency function which has code combinations to prevent potential interference from other remote units. The frequency on your Receiver and Transmitter units have been preset at the factory. We recommend changing the frequency while installing your ceiling fan instead of using the initial frequency set by the factory. Please use a small size tool to change the code switch setting. Step: 1 Open the remote battery cover and install DC12V,23A*1pc battery Step: 2 Within 30 seconds of turning the Receivers AC power ON. Step: 3 Press and hold remote any key for over 3 seconds, once the receiver has detected the frequency, Then fan turn off and light blink 3 times. This will indicate the receiver has learned the frequency that was previously selected on the transmitter. FUNCTIONS OF TRANSMITTER To turn the fan off.

: Turn on ceiling fan at high speed

: Turn on ceiling fan at medium speed.

: Turn on ceiling fan at low speed. Press and release immediately to turn on or off the light DIMMER- Press and hold to dim or brighten lights to the desired level and release. NOTE: Remove the battery if not used for long periods of time to prevent damage to the hand held remote. When pressing remote button, the LED indicator would be on. If you press remote button and LED indicator would not be on, you should change new DC12V,23A*1pc battery. To assure continued FCC compliance:

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. CAUTION:

To assure continued FCC compliance:

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FCC ID2AQZU-18024 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC: 25524-TR35F IC WARNING This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.

Reference No.: WTH21X04039333W Page 1 of 10 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: 2AQZU-18024 Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the devices expected lifetime. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

Satellite Electronic(Zhong Shan)Ltd. No.8, Chuang Ye Road, Torch Development Zone, Zhongshan, Guangdong, China Date: 2021-05-07 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AQZU-18024 Confidentiality Request To whom it may concern, Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of the information accompanying this application as outlined below:

XX Block Diagram CL] Tune-Up Information x] Operational Description L] Security Information XX] Schematics L] Software Defined Radio (SDR) LJ Parts List Information The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Satellite Electronic(Zhong Shan)Ltd.

(sean zheng)

(Manager)

Satellite Electronic(Zhong Shan)Ltd. No.8, Chuang Ye Road, Torch Development Zone, Zhongshan, Guangdong, China

(FCC ID > 2AQZU-18024) POWER OF ATTORNEY DATE: 2021-05-07 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Satellite Electronic(Zhong Shan)Ltd. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Satellite Electronic(Zhong Shan)Ltd.

(sean zheng)

(Manager)