Product Information and Regulatory Statement Important Safety Information - Read First!
Before installing, configuring, or operating any equipment, all relevant technical documentation must be read, understood, and followed. Savant technical documentation may contain important product-specific installation, mounting, and safety instructions, and can be accessed through the Savant Store. Scan the QR code or visit the URL below, enter the relevant product name or SKU in the Search Savant prompt, and select the product purchased to find documents, specifications and more. https://store.savant.com/DefaultStore/ccrz__HomePage Safety Statements Dclarations de Scurit All safety instructions below must be read, understood, and carefully followed under all applicable circumstances when working with any Savant equipment. Toutes les instructions de scurit ci-dessous doivent tre lues, comprises et soigneusement suivies dans toutes les circonstances applicables lorsque vous travaillez avec un quipement Savant. 1. Follow all input power ratings marked on product near power 1. Suivez toutes les puissances nominales indiques sur le input!
2. If fuse replacement is required, replacement fuse should match fuse rating marked on the product. 3. Do not use equipment near water. 4. Clean only with dry cloth. 5. Do not block any ventilation openings or install near any heat sources such as heat registers, stoves, radiators, amplifiers, etc. 6. Refer all servicing to qualified service personnel. Servicing is required when any part of the apparatus has been damaged in any way, or fails to operate normally for any reason. 7. Use only attachments/accessories specified by the manufacturer, following all relevant safety precautions for any such attachments/accessories. 8. For applicable equipment, use the included power cord with the grounding prong intact to insure proper grounding of the device. 9. If the provided plug does not fit the desired outlet, contact a licensed electrician to replace the obsolete outlet. 10. Protect any power cord from being walked on, pinched, strained, or otherwise potentially damaged, especially at the outlet or device connections. 11. Disconnect any outlet powered apparatus from its power source during lightning storms or when unused for long periods of time. 12. To completely disconnect equipment from AC mains power, disconnect the power supply cord plug from the AC receptacle on the device. 13. For any hardwired or fixed in-wall apparatus, carefully follow all wiring diagrams and instructions. All electrical wiring and servicing should be performed by a properly licensed electrician. produit prs de la puissance absorbe!
2. Si le remplacement du fusible est ncessaire, le fusible de remplacement doit correspondre la valeur nominale du fusible indique sur le produit. 3. Nutilisez pas dquipement prs de leau. 4. Nettoyer uniquement avec un chiffon sec. 5. Ne bloquez pas les ouvertures de ventilation et ninstallez pas proximit de sources de chaleur telles que les registres de chaleur, les cuisinires, les radiateurs, les amplificateurs, etc. 6. Confiez toutes les rparations un technicien qualifi. Un entretien est requis lorsquune partie de lappareil a t endommage de quelque manire que ce soit ou ne fonctionne pas normalement pour une raison quelconque. 7. Utilisez uniquement les attachements / accessoires spcifis par le fabricant, en suivant toutes les prcautions de scurit applicables ces attachements / accessoires. 8. Pour lquipement applicable, utilisez le cordon dalimentation inclus avec la broche de mise la terre intacte pour assurer une mise la terre correcte de lappareil. 9. Si la fiche fournie ne correspond pas la prise souhaite, contactez un lectricien agr pour remplacer la prise obsolte. 10. Protgez tout cordon dalimentation contre les pitinements, les pincements, les tensions ou autres dommages potentiels, en particulier au niveau de la prise ou des connexions de lappareil. 11. Dbranchez tout appareil aliment par une prise de courant de sa source dalimentation pendant les orages ou lorsquil nest pas utilis pendant de longues priodes. 12. Pour dconnecter compltement lquipement du secteur, dbranchez la fiche du cordon dalimentation de la prise secteur de lappareil. 13. Pour tout appareil encastr ou cbl, suivez attentivement tous les schmas de cblage et les instructions. Tout le cblage lectrique et lentretien doivent tre effectus par un lectricien dment agr. IMPORTANT NOTES:
For product mounting, installation, safety instructions, technical specifications, and more, refer to the product Quick Reference Guide, available via the link or QR code noted above. For regulatory and compliance information, see reverse of this sheet and/or product packaging. 1 of 2 45 Perseverance Way, Hyannis, MA 02601 Savant.com | 508.683.2500 Savant Product Regulatory Statement | 009-1950-01 200707 | 2020 Savant Systems, Inc. FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for CLASS B digital devices, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correcting the interference with one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect this equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement - Wireless and Handheld Devices Only FCC and IC Identifier - Devices with Integrated Screen or User Interface Only This device electronically displays the FCC declaration of conformity logo as well as the FCC and IC identifier. This information can be found on the device by accessing:
(Service menu) > About (A propos de) IC Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios. The Country Code Selection feature is disabled for products marketed in the US/Canada. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
2. Cet appareil accepter toute interfrence, y compris les interfrences pouvant provoquer fonctionnement indsirable dappareil. Dclaration IC 1. Lappareil ne doit pas produire de brouillage, et Dclaration dexposition aux radiations Cet quipement est conforme aux limites dexposition aux radiations de la FCC dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. Identificateur de la FCC et dLc
(Menu de service) > About (A propos de) Ce priphrique par voie lectronique affiche le logo de dclaration de conformit FCC ainsi que lidentificateur de la FCC et dIC. Cette information peut tre trouve sur le terminal en accdant :
2 of 2 45 Perseverance Way, Hyannis, MA 02601 Savant.com | 508.683.2500 Savant Product Regulatory Statement | 009-1950-01 200707 | 2020 Savant Systems, Inc. Circuit Test Instructions Use the instructions below to test that the dimmer module is functioning correctly. The setup requires the following:
Breaker test panel. The type of dimmer module determines the type of breaker panel (plug-on neutral or not). Forward Phase Companion Dimmer Module. Resistive loads with maximum amperage of 2.5 Amps. 15 amp circuit breaker. 120V AC source IMPORTANT!
When making connections, observe all general electrical best practices including wire sizing guidelines. The GPM-QP2FPD05-21 and GPM-Q2FPD05-21 modules can accept up to a #14 AWG wire. See the Branch Circuit Minimum Size of Conductors table on the previous page for wire sizing information 1. Plug a feeder breaker and a Forward Phase Dimmer Companion Module into the circuit breaker test panel. The feeder breaker should not 2. Connect the output of the feeder circuit breaker to the INPUT screw port on the dimmer module. 3. Connect a supported type load to Output A on the dimmer module. 4. Connect a second supported type load to Output B on the dimmer 5. Connect the unused side of each load to the neutral bus bar in the exceed 15A. module. breaker panel. 6. On modules that contain a neutral pigtail wire, connect the neutral wire to the neutral bus bar. 7. Apply power to the breaker panel (not shown in diagram) 8. Toggle the feeder circuit breaker On. 9. To test, toggle the CIRCUIT POWER switches A and B to ON and verify both loads switch On. 10. Toggle the CIRCUIT POWER switches to AUTO and verify the loads switch Off . NOTES Neutral Bus Bar 5 Neutral pigtail wire from the companion module 9 10 6 I R A P R E W O P T U C R C I I O T U A N O B A R E M M D I E S A H P D R A W R O F T U P N I T U P T U O T U P T U O B A PANEL CIRCUIT BREAKER 2 4 3 Load B 2.50 Amps Load A 2.50 Amps 1 8 Dual 300W Forward Phase Companion Module Dimmer Quick Reference and Installation Guide Box Contents
(1) Forward Phase Dimmer Module Descriptions GPM-QP2FPD05-21 QO Plug-on Neutral -or-
GPM-Q2FPD05-21 QO Pigtail
(1) Product Information and Regulatory Insert (009-1950-xx)
(1) Quick Reference Guide (this document) Speci cations Environmental Temperature 32 to 104 F (0 to 40 C) Humidity 5% to 85% Relative Humidity (non-condensing) Location Dimensions and Weights Indoor Use Only Module
(QO) Shipping Height Width Depth 1.48 in.
(3.76 cm) 1.71 in.
(4.34 cm) 5.00 in.
(12.70 cm) 7.50 in.
(19.05 cm) 2.63 in.
(6.68 cm) 4.30 in.
(10.92 cm) Weight
.5 lbs
(.23 kg) 1.0 lbs
(.45 kg) Power Input Power
(powers the module) Input Power
(from external source) Load Power 120V AC (+/-10%) @ 60 Hz, 0.1A (max) 120 AC per input - 15A (max) 300VA 2.5A @ 120V AC per channel 600VA 5.0a @ 120V AC per channel
(when just one channel is used) Features of Automatic Action Standards Type 1 Action Wireless Regulatory Safety and Emissions Bluetooth Low Energy (BLE) 2.4 GHz radio frequency FCC Part 15 UL ICES 003 Contains FCC ID:
PUU-QP2FPD05 Contains IC:
10798A-QP2FPD05 Compliant RoHS Recommended Load Center Types All QO compatible modules t into inch load centers Supported Load Types Standard Con guration Dimmable circuits Incandescent, halogen, magnetic low-voltage transformer, and forward phase dimmable uorescents Electrical and Safety Characteristics Screw Tighten Torque 3.0 Nm Wire / Conductor Type Copper (Cu) only Pollution Degree 2 Purpose of Control Operating Control, Smart Relay Control Module or the equivalent Software Class A 2500V Impulse Voltage Construction of Control Open Type Minimum Supported Release Savant OS da Vinci 10.2 Independently mounted for ush mounting D O N OT PRESS O N SCREEN REM OVE AFTER INSTALLATIO N CIRCUIT PO W ER PAIR B A C M E R F O R W A R D P H A S E DIM IN D O O R U S E O N LY 12 0 V A C 5 A M A X T O T A L 12 0 V A C 6 0 H z 12 0 V A C 6 0 H z G P M -Q P F P D 0 5 M O D U L E IN P U T:
H O M E A U T O M A TIO N E Q UIP L O A D IN P U T:
#14-8 A W G C u O N LY L O A D O U T P U T:
IC ID: 10 79 8 A-Q P 2F P D 0 5 F C C ID: P U U-Q P 2F P D 0 5 E 523 6 0 9 IN P U T O U T P U T A W Y Y W O U T P U T B A B F D E G A B C E F G Multi-Page LCD screen can display the following:
Energy usage in watts at the output. Percentage of brightness at the output. Firmware, Mac Address, and FCC/IC Info. Real time Bluetooth status connectivity icon. Manual Load Switches - Toggle to the ON position to switch load on. Toggle switch to AUTO for normal operation. Switch A controls output A and Switch B controls output B. PAIR Button - The PAIR button is a multi-use button. The duration that the button is pressed and held determines the function that gets initiated. Press and Release - Cycles through the screens available on the LCD (POWER > DIMMER > INFO 1 > INFO 2). Press and hold - Press and hold for 2 seconds to put module into pairing mode. Press and hold for 5 seconds to reset. D Input Power Connection - Connect the 120V AC output from the companion breaker to this input. Output Connections - The connections are labeled OUTPUT A and OUTPUT B. Connect each output to a separate load. See the Wiring section (page 2). 120V AC Connection - Plugs into the 120V AC bus bar in the breaker panel. The voltage on this connection powers the module. Neutral - The model number of the module determines the type of neutral connection on the module:
Plug-On Neutral - Positioned on the bottom of the module is a neutral clip that plugs directly onto the neutral bar. Pigtail Neutral - A neutral wire protrudes from the modules rear and gets wired to the neutral bar in the breaker panel Features Each output can control dimming loads up to 300 VA (volt-
ampere). See the Branch Circuit Minimum Size of Conductors table on page 2. All QO style dimmer modules are compatible with Schneider Electrics Square D QO load centers. Modules are forward phase (leading edge) type dimmers. Built-in energy monitoring; +/- 3% accuracy / 1 sec sample time. Communicates over the air using Bluetooth Low Energy (BLE) technology. Color LCD display for easy identi cation and load status. Dual 300W Forward Phase Dimmer | 009-2118-00 Copyright 2022 Savant Systems, LLC | 220124 4 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 Dual 300W Forward Phase Dimmer | 009-2118-00 Copyright 2022 Savant Systems, LLC | 220124 1 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 Output Power Maximums The table below shows the maximum wattage that the forward phase dimmer module can handle. Use the table to determine the number of loads that can safely be wired to each modules output. Wiring Use the appropriate diagram below when wiring the dimmer module, breaker, and load(s). Dimmer Type Incandescent MLV LED Forward Phase 300W 240W Not Recommended Plug-on Neutral Bus Bar with ARC Fault Breakers Plug-on Neutral Bus Bar with Standard Breakers Load B Load A Use AFCI / GFCI protection where required by local regulations Load B Load A Use AFCI / GFCI protection where required by local regulations Neutral Bar Neutral Bar Phase A Phase B Phase A Phase B Important Information To determine the feeder breakers size, do the following:
1. Determine the wattage requirements of each load connected to a dimmer module. 2. Sum up the wattage of all loads. 3. Divide the wattage requirements by the input voltage. This will be the current being drawn. spaces needed for the dimmer module Each circuit breaker requires one space Each dimmer module requires two spaces To determine the number of breaker panel spaces needed, add the number of spaces required for each circuit breaker to the number of The total current draw from the loads cant exceed 80% of the size of the breaker for that circuit. For example, with 15 amp breaker, 12 amps or 1440 watts. With a 20 amp breaker, max would be 16 amps or 1920 watts. Do not add MLV and ELV type loads to the same breaker/dimmer module circuit. MLV and ELV type loads should be connected to separate breaker circuits. Doing so can cause damage to the dimming module. ELECTRIC SHOCK! The 120V AC, 60 Hz source poses an electrical shock hazard that has the potential to cause serious injury to installers and end users. Branch Circuit Minimum Size of Conductors
(General circuit wiring, Copper Conductors) CAUTION! Risk of Electric Shock - More than one disconnect switch may be required to de-energize the device before servicing. IMPORTANT! A licensed electrician is required to install Savants Companion Modules. 15A 20A 30A 40A 50A 60A
#14 AWG #12 AWG #10 AWG #8 AWG
#6 AWG
#4 AWG NOTE: This wiring requirement was based on the National Electric Code
(NEC) (ANSI/NFPA70), Canadian Electric Code, Part 1 (CEC), and local codes Minimum Size of Conductors. Installation into Breaker Panel 1. Remove power from the breaker panel by switching off the panels main breaker. 2. Position and install a circuit breaker into one of the slots in the panel. Press rmly until the breaker is fully seated onto the appropriate bus bars. 3. Position and install the Savant dimmer module into the slot where it will be installed. Press rmly until the module is fully seated onto the appropriate bus bars. Typically the Companion Module(s) are installed alongside the circuit breaker but doesnt need to be. 4. Use the wiring diagram on the next page to complete the wiring. Breaker Panel Breaker Panel Standard Neutral Bus Bar with ARC Fault Breakers Standard Neutral Bus Bar with Standard Breakers Load B Load A Load B Load A Use AFCI / GFCI protection where required by local regulations Neutral from AFCI breaker. 120VAC Use AFCI / GFCI protection where required by local regulations Phase A Phase B Phase A Phase B To neutral on AFCI breaker ARC FAULT BREAKER I N P U T
G P M Q 2 F P D 0 5
. F O R W P H A S E D M M E R I A B A U T O O N I I C R C U T P O W E R P A R I A B O U T P U T O U T P U T plug-on neutral bar Gnd Bar 120VAC Neutral Bar ARC FAULT BREAKER I N P U T
G P M Q P 2 F P D 0 5 F O R W P H A S E D M M E R I A B A U T O O N I I C R C U T P O W E R P A R I A B O U T P U T O U T P U T Connect the pigtail wire to the neutral bar. Gnd Bar Breaker Panel BREAKER I N P U T
G P M Q 2 F P D 0 5 F O R W P H A S E D M M E R I A B A U T O O N I I C R C U T P O W E R P A R I A B O U T P U T O U T P U T plug-on neutral bar Gnd Bar 120VAC 120VAC Neutral Bar BREAKER A B O U T P U T O U T P U T I N P U T
G P M Q P 2 F P D 0 5 A D A P P H A S E D M M E R I A B A U T O O N I I C R C U T P O W E R P A R I Gnd Bar Breaker Panel Dual 300W Forward Phase Dimmer | 009-2118-00 Copyright 2022 Savant Systems, LLC | 220124 2 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 Dual 300W Forward Phase Dimmer | 009-2118-00 Copyright 2022 Savant Systems, LLC | 220124 3 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 Additional Documentation Further information is available in the documents listed below and can be accessed via the Savant Customer Community. Panel Bridge Controller - PoE (PBC-P1000) - QRG Savant Panelized Lighting Deployment Guide.