FCC ID: PUU-CANACR Remote control

PRODUCT COVERED Model Input voltage

(Vac, Hz) CAN06DW100R9RTWTNRO 120, 60 Current

(mA) 130 Wattage

(W) 16 BEFORE YOU BEGIN Read these instructions completely and carefully. STOP WARNING Risk of fire or electric shock. Installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Minimum 90C conductors, if uncertain contact a qualified electrician. These products are suitable for use in wet locations. IC rated for direct contact with insulation. PREPARE ELECTRICAL WIRING Electrical Requirements The LED fixture must be supplied with 120Vac 60Hz. Grounding Instructions The grounding and bonding of the overall system shall be done in accordance with National Electric Code (NEC) and local codes. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference; (2) this device must accept any interference received, including interference that may cause undesired operation. Installation Guide Remote Control Wafer light www.gelighting.com The GE brand and logo are trademarks of the General Electric Company. 2022 GE Lighting, a Savant company. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residen-

tial area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. PACKAGE CONTENTS 4 4 4 1 TOOLS REQUIRED Flathead Screwdriver Strain Relief Ladder Drywall Saw or Hole Saw Wafer light and junction box Gasket Hole template Remote control Power drill with 15/64 drill bit Safety Goggles Measuring Tape 1 2 2 2 Note: Reference the guide included with the Installation Mounting Template if using for installation. Installation mounting template sold separately. Not necessary for installation. Wall faceplate Drywall Anchor Screws Adhesive tapes INSTALLATION

1 2 Turn o power source to the power supply where you are installing the fixture. For a hole size of 6-1/4 inch, Use the hole template to trace the hole size. Cut the hole using a drywall saw or hole saw. 5 6 Place the junction box on the ceiling through the hole. Connect the light with junction box with the connector. Hold the spring clips against the fixture and gently guide into the ceiling until the clips snap into place. TRIM INSTALLATION Refer to this section if you bought the trim accessory Option A Option B 3 Option A:Remove the knockout with a screwdriver and use the strain relief to fish the wires into the J-Box. Option B:use the wire clamps to fish the wires into the J-Box. 4 Connect the wires into quick connector:

Black to black White to white Green to green or bare copper wire Close the cover of the junction box. Decorative Trims (Brushed Nickel, Oil Rubbed Bronze, Square) Wall wash trim Before trim installation, ensure the wafer is powered off. Push the trim into the wafer, ensure all clips on the trim are fixed to the light. Note:

Compatible trim accessory:

CANAC06BNRO/ CANAC06OBRO/CANAC06BNSQ/ CANAC06OBSQ/-

CANAC06WHSQ/ CANAC06WHWW INSTALLATION - REMOTE CONTROLLER This remote controller can be mounted to the wall in two ways, by screws or adhesive tape. Once you determine which install method is best for you, select one of the following setup methods. Note: The wall faceplate is not designed for installation over an outlet box. Option A: Mounting with screws Option B: Mounting with adhesive tape Ensure the installation surface is clean and dry This product is not suitable for textured, porous, wallpaper or brick wall surface. Mark the appropriate two keyhole locations. Drill two holes 3.28 apart using 15/64 size drill bit. Insert drywall anchors. Screw on the faceplate bracket, then snap the faceplate cover onto the bracket. Then place the remote controller into the groove of the faceplate. Apply adhesive tape to the groove of the faceplate brackets back . Then mount the bracket to the wall. Snap the faceplate cover onto the bracket. Then place the remote controller into the groove of the faceplate. USING THE REMOTE CONTROLLER NOTE: Pull out the plastic card from the battery compartment before using your remote controller. CHANGING THE BATTERY LED Indicator On/off button, turn on or turn off the light Dim down button, use it to decrease the brightness Dim up button, use it to increase the brightness CCT Button, use these to select different CCT Long Press: Cycle through CCT sequence. Color Button, use these to select different colors Long Press: Cycle through Color sequence. User guide:

Turn on light(s) in 30 second, long press and for 5 seconds;

the light will flash twice until the controller and lights pair together. Then you can use your controller control to the lights. Note: To pair other devices, repeat the process. To remove the fixture from the remote: Turn on the light(s) and wait 30 seconds: Long press and for 5 seconds until the light flashes twice. This will remove the device. Low battery: When the LED indicator light is red, change the battery. Factory reset: Long press and for 5 seconds until the indicator flashes green. Remove the back cover of remote using the screwdriver to change the CR2032 battery. WARNING : Chemical Burn Hazard- Do not ingest or swallow coin cell battery. This remote control contains a coin cell battery. If the coin cell battery is swallowed or ingested, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used coin cell batteries away from children. If the battery compartment does not close securely, stop using the remote control and keep away from children. If you think coin cell batteries have been swallowed or placed inside any part of the body, seek immediate medical attention. AVERTISSEMENT : Risque de brlure chimique - Ne pas ingrer ou avaler la pile bouton. Cette tlcommande contient une pile bouton. Si la pile bouton est avale ou ingre, elle peut provoquer de graves brlures internes en seulement 2 heures et entraner la mort. Gardez les piles boutons neuves et usages hors de porte des enfants. Si le compartiment piles ne se ferme pas correctement, cessez d'utiliser la tlcommande et gardez-la hors de porte des enfants. Si vous pensez que des piles bouton ont t avales ou places l'intrieur d'une partie du corps, consultez immdiatement un mdecin. Additional Information and Warnings FCC Compliance Statement Compliance Notice:

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Statement This device complies with RSS247 of Industry Canada. Cet appareil se conforme RSS247 de Canada dIndustrie. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. Cet quipement est conforme aux limites dexposition aux rayonnements IC RSS-102 dfinies pour un environnement non contrl.

FCC ID and IC ID, HVIN, PMN are laser etched to the device FCC ID: PUU-CANACR IC: 10798A-CANACR HVIN: CANACR PMN: Remote control The FCC ID, IC, HVIN, PMN will be laser etched here:

Savant Technologies LLC dba GE Lighting, a Savant company Request for Confidentiality Date: February 14, 2023 Subject: Confidentiality Request for: ___FCC ID: PUU-CANACR and IC ID:_ 10798A- CANACR _ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and/or IC RSP-100, Section 12.4, the applicant requests that a part of the subject application(s) be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Exhibit Permanent Block Diagrams

--------------------------- External Photos Permanent *1 Internal Photos Permanent Operation Description/Theory of Operation Permanent Parts List & Placement/BOM Permanent Tune-Up Procedure Permanent Schematics

--------------------------- Test Setup Photos Permanent *1 Users Manual Savant Technologies LLC dba GE Lighting, a Savant company has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality for FCC Applications:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __ (specify number of days not to exceed 180)2___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Short Term Confidentiality for Industry Canada Applications:

Starting May 2022, ISED will recognize short term confidentiality on certain exhibits until the intended date of marketing. The applicant requests the exhibits selected above as short term confidential be withheld from public view until: (specify ISED expiration date / date of marketing) . Sincerely, By:

Lead Systems Engineer Safety & Regulatory _________ Paul Smith _____

(Signature/Title3)

(Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Please refer to https://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 050222-17

THIS MUST BE SIGNED BY THE APPLICANT/AGENT AND SHOULD BE PLACED ON APPROPRIATE LETTERHEAD Authority to Act as Agent Date: December 28, 2022 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern:

_DEKRA Testing and Certification (Shanghai) Ltd. Guangzhou Branch is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, By:

(Signature1) _Paul Smith_________________

(Print name) Title:

Lead Systems Engineer Safety & Regulatory__________________________ On behalf of: _ Savant Technologies LLC, dba GE Lighting, a Savant Company _______

(Company Name) Telephone:

__+1 216 266 2189_________________________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 050222-17

GE Lighting, a Savant company Savant Technologies LLC 1975 Noble Rd., East Cleveland, OH 44112 Certification Application Attestation Statements Date: February 8, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern:

Statement for 47 CFR section 2.911(d)(5)(i) Savant Technologies LLC dba GE Lighting, a Savant company certifies that as of the date of the application the equipment for which authorization is sought is not covered equipment1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not covered equipment. Additional Explanation: <N/A>

Statement for 47 CFR section 2.911(d)(5)(ii) Savant Technologies LLC dba GE Lighting, a Savant company (the applicant) certifies that, as of the date of the filing of this application, the applicant is not identified on the Covered List as an entity producing covered equipment. Thank you, By:

(Signature2) _________Paul Smith____________

(Print name) Title:

_Lead Systems Engineer safety & Regulatory_ Company:

_ Savant Technologies LLC dba GE Lighting, a Savant company Telephone:

_(1) 216 266 2189__________ 1 - The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters should be placed on appropriate letterhead.

GE Lighting, a Savant company Savant Technologies LLC 1975 Noble Rd., East Cleveland, OH 44112 U.S. Agent Designation for Service of Process

(Applicant is Both Grantee and U.S. Agent) TO:

American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 ATTENTION: FCC Certification Section 2.911(d)(7) Information This letter is to confirm that the Applicant will also serve as the U.S. Agent for Service of Process as required by 47 CFR 2.911(d)(7). The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The Applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information changes. Savant Technologies LLC dba GE Lighting, a Savant company PUU 0022026876 Paul Smith 1975 Noble Road Cleveland, Ohio, United States, 44112

(1) 216 266 2189 paul.smith@savant.com Applicant Company name:

Grantee Code:

FRN:

Contact Name:

Street Address:

City/Province/Zip:

Telephone No:

Email:

Applicant Signature:

Date: 8 February 2023 Signed by (Printed Name/Title):

Paul Smith Lead Systems Engineer Safety & Regulatory