Portable control unit (transmitter) D3 DRC-MP D3 DRC-MP: 2.4 GHz transmitter Scanreco AB Stenstravgen 13, SE-127 39 Skrholmen Box 90304, SE-120 25 Stockholm, Sweden Tel +46 8 556 32 800 www.scanreco.com This product is intended to be installed in a Control unit system as a transmitter by Scanreco AB and it is designed preferably for wireless control of crane installations, travelling hoist units, chain and rope hoists, transfer carriages and similar applications. Terminal diagrams:
Scanreco AB Stenstravgen 13, SE-127 39 Skrholmen Box 90304, SE-120 25 Stockholm, Sweden Tel +46 8 556 32 800 www.scanreco.com Radio part diagram:
Radio specification:
Attribute Information 2.405 2.480 GHz Frequency Channels Channels management Channel bandwidth RF Power 16 FHSS 2.7 MHz
+18 dBm typical Modulation GFSK Range 100 meter Antenna specification:
1 2 Scanreco AB Stenstravgen 13, SE-127 39 Skrholmen Box 90304, SE-120 25 Stockholm, Sweden Tel +46 8 556 32 800 www.scanreco.com N Antenna type Details Manufacture Part number Connector Gain Dipole antenna Scanreco 50250 TNC 2 dBi Striaght antenna Nearson 102784 TNC/SMA 5 dBi Total length 82 mm, 17mm 185 mm length, 13mm Installation description:
Figure 1 Figure 2 1- Assemble D3 DRC-MP to box with screws. Torque =0.7Nm. 2- Screw antenna connector to PCBA. Torque = 0.56Nm 3- Assemble transparent plastic cover. Tightening torque = 0.7Nm, see Figure 2. Scanreco AB Stenstravgen 13, SE-127 39 Skrholmen Box 90304, SE-120 25 Stockholm, Sweden Tel +46 8 556 32 800 www.scanreco.com FCC information This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Warning Industry Canada information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. CAN ICES-3 (A)/NMB-3(A) Scanreco AB Stenstravgen 13, SE-127 39 Skrholmen Box 90304, SE-120 25 Stockholm, Sweden Tel +46 8 556 32 800 www.scanreco.com