FCC ID: N5OD3DRCDRBM DRC-DR D3, DRC-BM D3

Operating/assembly instructions DRC-DR D3 and DRC-BM D3 radio receivers 151014 enGB 211 267 44 719 IS 975 Manufacturers address:

Original operating/assembly instructions Terex MHPS GmbH Forststrasse 16 40597 Dsseldorf, Germany www.demagcranes.com mhps-info@terex.com H b m G S P H M x e r e T 2 Further documents:

DRC-10 D3 operating/assembly instructions DRC-J D3 operating/assembly instructions 211 266 44 211 271 44 719 IS 975 719 IS 975 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 Contents 1 General 1.1 Information on the DRC-DR radio receiver 1.2 General information 1.3 1.4 1.5 1.6 1.7 1.8 1.9 Information on the operating/assembly instructions Symbols/signal words Liability and warranty Copyright Spare parts Definitions After-sales service 1.10 Disposal of machine parts 2 Safety 2.1 General 2.2 2.3 Intended use Responsibility of the owner 2.4 Operating personnel requirements 2.5 2.6 2.7 2.8 3 3.1 3.2 4 5 5.1 5.2 5.3 5.4 Personal protection equipment Regular inspections Safety instructions for installation and disassembly Safety instructions when first putting the unit into service after completing installation General description Transmitter/receiver interface Transmission method Technical data Putting the DRC-DR radio receiver into operation for the first time Safety instructions Installing the radio receiver card Function following installation Putting the receiver into operation for the first time 6 Using DRC radio controls 6.1 DRC-DR receiver operating functions in connection with a transmitter 6.1.1 F1 function key 6.1.2 F2 function key 6.1.3 F1/F2 function keys additional functions 6.1.4 Horn key, 1st stage 6.1.5 Horn key, 2nd stage 7 P International postal approval FCC and Industry Canada Information 4 4 4 4 5 6 6 6 7 8 8 9 9 9 10 11 11 11 11 12 13 13 13 14 15 15 16 18 18 19 19 19 19 19 19 19 20 22 3 H b m G S P H M x e r e T 4 1 0 1 5 1 d d n

/

i

. 4 4 7 6 2 1 1 2 1 General 1.1 Information on the DRC-DR radio receiver 1.2 General information 1.3 Information on the operating/assembly instructions You have purchased a Demag product. If special designs or additional options are ordered or the latest technical modifications are incorporated, the actual scope of supply may differ from the data and information as well as from the illustrations described here. If you have any questions, please contact the manufacturer. DRC-DR radio receivers may only be operated by personnel who are fully familiar with the operating/assembly instructions. DRC D3 (3rd generation) transmitters and receivers are successors to the D2 generation of DRC units. D3 units are to replace D2 generation radio systems wherever D3 units are allowed to be operated without the need for any registration or fees. In this context, see section 7 International postal approval. DRC D3 generation units are not technically compatible with units from the previous DRC D2 generation. This means that D3 generation transmitters and receivers cannot be combined with D2 units. These operating/assembly instructions are designed to provide the owner with appropriate instructions for safe and correct operation and for maintenance. These operating/assembly instructions are an integral part of the DRC-DR radio receiver. Every individual given the task of transporting, installing, commissioning, operating, maintaining and repairing DRC-DR radio receivers and their additional equipment must have read and understood the items listed in the following:

The operating/assembly instructions must be available to operating personnel at all times in order to prevent operating errors and to ensure smooth and trouble-free operation of our products. They must be kept available in the immediate vicinity at all times. the operating/assembly instructions the safety regulations the safety instructions in the individual chapters and sections. H b m G S P H M x e r e T 4 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 1.4 Symbols/signal words Important safety information and instructions are marked by corresponding sym-

bols and signal words in these operating/assembly instructions. Safety instructions and information must be followed. Follow these instructions with care to avoid any accidents, injuries or damage. Any locally applicable accident prevention regulations and general safety regula-

tions must also be followed. The following symbols and instructions warn against possible injuries or damage and are intended to assist you in your work. DANGER. This symbol indicates an immediate hazard which can result in serious injury or death. WARNING. This symbol indicates a possibly hazardous situation which might result in seri-

ous injury or death. CAUTION. This symbol indicates a possibly hazardous situation which might result in medium to light injury. i NOTE Operating hazard for the DRC-DR radio receiver This symbol indicates information on the appropriate use of DRC-DR re-

ceivers. Failure to follow these instructions may result in malfunctions, damage or pollution of the environment. H b m G S P H M x e r e T 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 5 1.5 Liability and warranty All information included in these operating/assembly instructions has been compiled on the basis of the relevant regulations, state-of-the-art engineering principles and our many years of experience. i NOTE These operating/assembly instructions must be read carefully before starting any work on and with the DRC-DR receiver, especially before the unit is put into operation for the first time. The manufacturer assumes no liability for any damage which results from the following:

Non-compliance with the operating/assembly instructions Operation by insufficiently trained personnel Unauthorised conversions Any technical modifications Inappropriate use of the DRC-DR radio receiver Wearing parts are not subject to liability for defects. We reserve the right to incorporate technical modifications within the scope of improving the operating characteristics and further development of the DRC-DR radio receiver. These operating/assembly instructions must be treated confidentially. They are only intended to be used by people who work with or on the DRC-DR radio receiver. Any and all content, texts, drawings, images and any other information are protected within the sense of copyright law and are subject to further industrial rights. Any misuse is an offence. No part of this documentation, in whole or in part, may be reproduced, distributed, shown in public or used in any other way without specific prior consent. Infringe-

ments are an offence resulting in obligatory compensatory damages. Further rights reserved. All industrial rights reserved. 1.6 Copyright 1.7 Spare parts Only genuine Terex MH spare parts may be used. CAUTION. Defective spare parts Incorrect or defective spare parts may cause damage, malfunctions or complete failure of DRC DR receivers. Only use genuine spare parts or parts approved by Terex MH. For safety-relevant wear parts, genuine Demag spare parts must always be used. Safety-relevant wear parts are, for example, brake linings, ropes, etc. The use of unauthorised spare parts renders null and void any claims for warranty, service, damages or liability against the manufacturer or his appointed personnel, dealers and representatives. H b m G S P H M x e r e T 6 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 1.8 Definitions Owner Owners (employer, company) are defined as persons who own a radio control sys-

tem and who use it as intended or allow it to be operated by suitable and instructed persons. Operating personnel/operator Operating personnel are defined as persons entrusted by the owner of a radio control system with operation of the radio control system. Specialist personnel Specialist personnel are defined as persons assigned by the owner of the radio control system to carry out special tasks such as installation, setting-up, maintenance and fault elimination. Qualified electrician Qualified electricians are defined as persons who, owing to their technical train-

ing, knowledge and experience of electric equipment as well as knowledge of the relevant standards, codes of practice and regulations, are able to assess the tasks given to them and to identify and eliminate potential hazards. Trained person Trained persons are defined as persons who have been instructed and trained for the tasks assigned to them and on the possible hazards resulting from incorrect handling and who have been informed about the required protective devices, protective measures, relevant regulations, codes of practice, accident prevention regulations and operating conditions and who have proven their qualifications. Experienced technician Experienced technicians are defined as persons, who, owing to their technical training and experience, have sufficient knowledge of radio control systems and are familiar with the relevant national industrial safety regulations, codes of practice, accident prevention regulations, directives and generally accepted engineering standards enabling them to judge the safe operating condition of radio control systems. Assigned expert engineer (where the rules and regulations of the German Social Accident Insurance (DGUV) apply in the Federal Republic of Germany, for determining the S.W.P.) An assigned expert engineer is defined as an experienced technician specifically assigned by the manufacturer to determine the remaining duration of service

(service life) of rope hoists (S.W.P. = safe working period) and to carry out a general overhaul of rope hoists. Authorised expert engineer (where the rules and regulations of the German Social Accident Insurance (DGUV) apply in the Federal Republic of Germany) In addition to the expert engineers of the Technical Supervisory and Inspection Board, an authorized expert engineer for the inspection of radio control systems is defined as an expert engineer authorized by the Industrial Employers Mutual Insurance Association. Radio control system Radio control systems are systems used for wirelessly controlling the lifting, lower-

ing and travel motions of loads on cranes, crabs, machinery and installations. H b m G S P H M x e r e T 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 7 1.9 After-sales service Our after-sales service will provide you with all technical information on Terex MH products and their systematic application. Should you have any questions regarding our products, please refer to one of our after-sales service centres, the relevant representative or the head office in Wetter. Please quote the serial or order no. in any correspondence or for spare part or-

ders. Specifying this data ensures that you receive the correct information or the re-

quired spare parts. Manufacturers address:

Terex MHPS GmbH Forststrasse 16 40597 Dsseldorf, Germany www.demagcranes.com mhps-info@terex.com Addresses and contacts The current addresses of the sales offices in Germany and the subsidiaries and agencies worldwide can be found on the Terex MHPS GmbH homepage at www.demagcranes.com/Contact 1.10 Disposal of machine parts Unless a return or disposal agreement has been concluded, recycle separated components after proper removal:

Scrap any remaining metallic material Dispose of plastic elements for recycling Separate and dispose of any other components by material type i NOTE Electric scrap, electronic components, lubricants and other auxiliary materials are subject to special disposal regulations and may only be disposed of by certified companies. National disposal regulations must be considered regarding environmentally friendly disposal of the electric components and machine parts. Further information can be obtained from corresponding local authorities. H b m G S P H M x e r e T 8 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 2 Safety 2.1 General 2.2 Intended use The Safety chapter provides an overview of all important safety aspects for op-

timum protection of personnel as well as safe and trouble-free operation of the DRC-DR radio receiver. At the time of its development and manufacture, the DRC-DR radio receiver was built according to generally accepted engineering standards and is considered to be safe to operate. The DRC-DR radio receiver may still be a cause of danger if it is not used correctly or as intended by suitably trained personnel. Knowledge of the contents of the operating/assembly instructions is one of the requirements necessary to protect personnel from hazards and to avoid malfunctions and, therefore, to operate the DRC-DR radio receiver safely and reliably. Any conversions, modifications or additions to the DRC-DR radio receiver are prohibited unless approved in writing by Terex MH. The DRC-DR radio receiver is intended to be used as a receiver unit for DRC-10 and DRC-J radio transmitters. The scope of functions is exclusively designed for wireless remote control of crane installations with Demag DR rope hoists. For these applications, therefore, cable-connected control equipment (control pendants) can be dispensed with. The operator can position himself as required. He can freely move loads from a safe distance in line with local conditions. DRC transmitters and receivers meet the requirements of the standards and regulations listed in the EC conformity declaration. The specified EC conformity declaration is an integral part of the relevant operating/assembly instructions. DRC transmitters and receivers do not require any registration or operating fees, see section 7 International postal approval. The benefits that this provides for the user are also utilised by some other manufacturers of devices for communications and telemetry applications. The consequence of this is that the relevant approved frequency ranges may be used by many transmitters at the same time, depending on the time and location. The transmission method used by Terex MH is designed for the most robust and interference-resistant radio transmission between the transmitters and receivers of the DRC range. Frequencies in the so-called 2,4 Ghz ISM band are used for transmission of radio signals between transmitters and receivers. Despite all of the technical precautions taken by Terex MH, it cannot be entirely excluded that the transmission characteristics of other radio systems are impaired, in particular devices supplied by other manufacturers that use the same frequency range, or that the transmission characteristics of the system supplied by Terex MH are negatively affected. In such cases, interference or radio connection interruptions may occur, which disrupt the communication and function of a system supplied by Terex MH or other manufacturers. Such impairment or interference does not constitute a defect on the part of DRC transmitters/receivers. Terex MH accepts no liability for wilful or grossly negligent behaviour. The number of transmitters that operate without any interference in a given area depends on the relevant radio solution design of all systems and the selectivity of each individual system. If this limit is exceeded continuously or for certain periods, additional technical measures may be necessary in order to ensure simultaneous and interference-

free operation of the radio systems. Whether and to which extent such measures are required can only be determined by means of suitable measurements on site or when the system is put into operation. Terex MH is not responsible for such additional technical measures. DRC D3 transmitters and receivers can be used for multiple transmitter operation as well as multiple receiver operation. Refer to the corresponding operating/

assembly instructions for details. 9 H b m G S P H M x e r e T 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 2.3 Responsibility of the owner DRC radio control systems may only be operated when in perfect working order by trained personnel in accordance with the relevant safety and accident prevention regulations. This also includes compliance with the operating and maintenance conditions specified in the operating/assembly instructions. National occupational safety and health regulations must be observed and followed. For intended use, the information in the operating/assembly instructions for the radio transmitter used (DRC-10/DRC-J) and the machine/crane installation to be controlled must be complied with in addition to the information contained in these operating/assembly instructions (see accompanying documents, page 2). Serious personal injury or damage to property may occur in the event of:

unauthorised removal of covers, working on live parts. inappropriate use of the product/system, incorrect operation, insufficient maintenance, Information on safety at work refers to the regulations of the European Union that apply when the DRC-DR radio receiver is manufactured. The owner is obliged to ensure that the specified industrial safety measures comply with the latest rules and regulations and to observe new regulations during the entire service life of the DRC-DR radio receiver. Local industrial safety legislation and regional regulations and codes of practice applicable at the site of operation of the DRC-DR radio receiver must be observed outside the European Union. General safety, accident prevention and environmental protection regulations that apply where the DRC-DR radio receiver is in operation must be observed and complied with in addition to the safety instructions contained in these operating/

assembly instructions. The owner and any personnel authorised by him are responsible for correct operation of the DRC-DR radio receiver and for clearly defining responsibilities for installation, operation, maintenance and cleaning. The operating/assembly instructions must be followed in full and without any limitations. The operating/assembly instructions must, if required, be supplemented by the owner with instructions relating to organisation of work, working procedures, authorised personnel, supervising and reporting obligations, etc. Furthermore, the owner must ensure that any further working and safety instructions resulting from the risk assessment of the DRC-DR radio receiver workplaces are specified in operating procedures. the operating/assembly instructions are always kept available in the immediate vicinity of the DRC-DR radio receiver for installation, operating, maintenance and cleaning personnel. personnel are trained in accordance with the work to be performed. the DRC-DR radio receiver is only operated when in safe and proper working order. the safety devices are always kept freely accessible and are checked regularly. the national regulations for use of the DRC-DR radio receiver are observed. The owner is urged to develop procedures and guidelines for any malfunctions, to instruct users and to affix these instructions at a suitable place where they can be easily seen. H b m G S P H M x e r e T 10 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 2.4 Operating personnel requirements Only authorised and trained personnel may work on the DRC-DR radio receiver. Personnel must have received instruction on the DRC-DR radio receiver functions and any hazards that may occur. Every individual given the task of working on or with the DRC-DR radio receiver must have read and understood the operating/assembly instructions before any work starts. Persons under the influence of drugs, alcohol or medicines which affect their reactions must not work on or with the DRC-DR radio receiver. Age and job-specific regulations relevant at the place where the DRC-DR radio receiver is operated must be observed for the selection of any personnel. Personnel are obliged to report to the owner without delay any changes to the DRC-DR radio receiver that impair safety. For maintenance work on the DRC-DR radio receiver, the owner may only employ persons (specialist personnel) who are at least 18 years of age, who are mentally and physically suitable, who have been instructed in maintenance of the DRC-DR radio receiver and who have proven their qualification to the owner in this respect. 2.5 Personal protection equipment When work is carried out on or with the DRC-DR radio receiver, the following must always be worn:

Protective clothing, closely fitting working clothes (low tear strength, no loose sleeves, no rings or any other jewellery, etc.). Safety shoes to protect against falling parts and against slipping. Safety helmet to be worn by everybody in the danger zone. 2.6 Regular inspections the DRC-DR radio receiver must be inspected before it is put into operation, the DRC-DR radio receiver must be inspected regularly. The owner of the DRC-DR radio receiver may be obliged to carry out regular inspections by national industrial safety legislation and regional regulations. This is regulated by the rules and regulations of the German Social Accident Insurance

(DGUV) in the Federal Republic of Germany, for example. These specify that The owner is obliged to ensure that the DRC-DR radio receiver complies with the latest rules and regulations and to observe new regulations at all times. If no comparable inspection regulations or requirements apply at the place where the DRC-DR radio receiver is operated, we recommend compliance with the above-mentioned regulations. 2.7 Safety instructions for installation and disassembly Installation and disassembly work may only be performed by experienced technicians. Installation and disassembly work must be co-ordinated by the person carrying out the work and the owner within the scope of their responsibility. The working and danger zone must be made safe. The installation must be isolated in accordance with the relevant electric regula-

tions. Customer-specific regulations must be observed. Only appropriate, tested and calibrated tools may be used. If equipment is disassembled, any waste material must be disposed of by the owner in an environmentally compatible way in compliance with relevant regula-

tions. 11 H b m G S P H M x e r e T 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 2.8 Safety instructions when first putting the unit into service after completing installation The working and danger zone must be made safe. First check that the voltage and frequency specified on the type plate match the control voltage of the installation/machine. The commands for controlling the motion drives are disabled in the DRC-DR radio receiver until a transmitter has been clearly assigned and specified by means of the relevant initialisation dialogues and the crane ID. See transmitter operating/assembly instructions (DRC-10 or DRC-J). In the course of putting the equipment into service, it may be necessary to render safety devices or features inoperative while adjustment work or function checks are carried out. Work may need to be carried out in the danger zone when the product is put into service. Therefore, it must be ensured that only appropriately trained personnel are employed for this work. H b m G S P H M x e r e T 12 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 3 General description 3.1 Transmitter/receiver interface 3.2 Transmission method Demag DRC radio control systems are designed for wireless control of hoist units and cranes. They are the man/machine interface for manually controlled crane installations. The relevant EU directives and standards are complied with for this application. A DRC D3 radio control system consists of one or more transmitters as well as at least one or, if required, more receivers. These operating/assembly instructions refer to DRC DR D3 receivers in combination with their matching DRC-10 D3 or DRC-J D3 transmitters. The DRC-DR radio receiver is a PCB that is designed to be installed in the electric equipment cover of a DR hoist unit. The interface of this receiver component to the crane control system is the Can bus with the CANopen safety protocol and the power supply via the DR electric equipment. The DRC-DR radio receiver is exclusively suitable for operation with a DR hoist unit with processor control. Demag DRC-DR radio receivers are equipped for bi-directional radio transmission and transmit information to DRC-10 hand-held transmitters or DRC-J joystick controls. This increases the safety and reliability of the radio system. Status information for the crane control system and the receiver is shown on the display of the DRC-10 or DRC-J transmitter. Frequencies in the so-called 2,4 Ghz ISM band are used for transmission of radio signals between transmitters and receivers. The new proprietary radio transmission method used for DRC D3 meets the most demanding requirements in terms of transmitter density and co-existence with other equipment that operates in the 2,4 GHz ISM band. The radio transmission method combines various transmission mechanisms: A frequency-hopping system ensures that radio transmission is robust and highly resistant to interference an adaptive behaviour (Listen Before Talk) combined with this enables interference with neighbouring radio applications to be effectively eliminated. H b m G S P H M x e r e T 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 13 4 Technical data DRC-DR radio receiver PCB Radio transmission CAN bus LED indicators for Enclosure Temperature range Weight of radio receiver Supply voltage Typical range Frequency range output radio connection (yellow LED) Line voltage (green LED) Internal error (red LED) IP 55 integrated in rope hoist controls

- 20 to + 70 C 94 g

+5 V DC (from the rope hoist controls) approx. 100 m 2,4 GHz ISM band, 2405 - 2480 MHz H b m G S P H M x e r e T 14 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 5 Putting the DRC-DR radio receiver into operation for the first time 5.1 Safety instructions DANGER. Electric current. Electric energy may cause very severe injuries. Work on the electric equipment may only be carried out by specialists or by trained personnel. Before starting work, switch off the electric power supply and secure it against switching on again. WARNING. Risk of injury if incorrectly assembled Incorrect installation may result in severe injury and/or damage to prop-

erty. Therefore, this work may only be carried out by authorised, instructed person-

nel who are familiar with the principle of operation of the DRC-DR radio re-

ceiver in compliance with all safety regulations:

Ensure sufficient working clearance before starting assembly work. Secure and fence off the working and danger zone. Wear protective clothing. Be careful when working on open components that have sharp edges. Risk of injury. Keep the working area clean and tidy. Store any machine parts or fittings and tools that are not needed in such a way that there is no risk of them falling. Fit components correctly and as intended. Comply with specified bolt tight-

ening torques. Incorrectly fitted components may fall and cause severe injuries. i NOTE These operating/assembly instructions must be read carefully before starting any work on and with the DRC-DR receiver, especially before the unit is put into operation for the first time. The manufacturer assumes no liability for any damage which results from the following. non-compliance with the operating/assembly instructions untrained personnel unauthorised conversions technical modifications inappropriate use H b m G S P H M x e r e T 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 15 5.2 Installing the radio receiver card To install the radio receiver card, proceed as follows:

Before starting any installation work, disconnect the system from the power supply. Install the radio receiver card in the appropriate slot Insert the radio receiver card into the appropriate slot Fix the radio receiver card in the electric equipment cover by means of the two screws 42354344.eps 42354444.eps H b m G S P H M x e r e T 16 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 42354544.eps Connecting the flat cable from the radio receiver to the controller card of the rope hoist control system 42354644.eps 42354844.eps Installation of the radio receiver card is finished when the above steps been completed. Before the system is put into operation again, make sure that other control components such as, for example, the DSE-10R control pendant with cable, have been disconnected from the system. Otherwise, no clear assign-

ment of the control units is possible. 42354744.eps 17 H b m G S P H M x e r e T 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 5.3 Function following installation A general function check of the radio receiver card can be carried out by means of the light emitting diodes. DIP LED1 LED2 LED3 LED LED1 LED2 LED3 LED1 Off Off Colour Yellow Green Red LED2 Flashing On Flashing On LED3 Off Off Off Off Off On 43608844.jpg Meaning Radio connection, flashing steadily Power on, no error (continuously lit or flashing) Error(s) occurred Meaning Receiver power on, no transmitter logged on Receiver power on. Transmitter logged on, but no radio connection (transmitter off or on standby) Receiver has a radio connection Steady flashing indicates good radio connection Irregular flashing indicates radio interference Radio connection exists in STOP, Run and parameter-

programming modes An internal error has occurred, shown on the transmitter display Further function checks are only possible by operation of the corresponding DRC-10 or DRC-J radio transmitters. For this purpose, please refer to the operating/assembly instructions for the relevant DRC-10 or DRC-J radio transmitter and for the crane installation (see accompanying documents, page 2). You will also find corresponding instructions for eliminating possible faults in a radio control system in the operating/assembly instructions for the DRC-10 or DRC-J radio transmitter and the crane installation. When delivered, the DRC-DR radio receiver has crane ID NOID. All crane movements are blocked. This block is removed when the unit is put into operation by the assignment of a valid crane ID (other than NOID) to the receiver. The radio receiver can be put into operation by means of the relevant radio transmitter (DRC-10 or DRC-J). The procedure for putting the radio control system into operation is described in detail in the operating/assembly instructions for the transmitter. Operating/assembly instructions required in addition:

Radio transmitter Ident. no.:

DRC-10 D3 hand-held transmitter 211 266 44 DRC-J D3 joystick transmitter 211 271 44 5.4 Putting the receiver into operation for the first time 18 H b m G S P H M x e r e T 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 6 Using DRC radio controls 6.1 DRC-DR receiver operating functions in connection with a transmitter 6.1.1 F1 function key Example: tandem operation The functions that can be called up with the F1, F2 or horn keys on DRC-10 and DRC-J transmitters in connection with a DRC-DR receiver are described in the following:

Actuate the F1 key to change the crab selection if there are several crabs. The selection is incremented one step further every time the key is actuated:

I => II => I+II => I The modified crab selection is shown on the display of the transmitter. If there is only one crab, the F1 key has no function. i NOTE After the transmitter is fully switched off:

or after the rechargeable battery is replaced, the crab selection always starts with crane crab 1 when the system is restarted; this means that hoist unit 1 always starts first when the system is restarted. DANGER If the selection settings on the transmitter are ignored, e.g. for tandem operation. Failure to comply with the selection settings on the transmitter repre-

sents an immediate hazard which can result in serious injury or death. You must always set the crab selection on the transmitter when it is switched on again after it has been fully switched off. 6.1.2 F2 function key If the parameters are programmed as follows, the current load value of the selected crab(s) is saved as a tare value when the F2 key is actuated for 5 seconds. 6.1.3 F1/F2 function keys additional functions The F1 and F2 keys can also be assigned optional additional functions (e.g. switch between tandem units, etc.). 6.1.4 Horn key, 1st stage 6.1.5 Horn key, 2nd stage When the 1st stage of the Horn key is actuated, the horn in the crab control system is activated. When the 2nd stage of the Horn key is actuated and held down for more than 5 seconds, the limit switch test is activated for hoist units that are equipped with operating limit switches. H b m G S P H M x e r e T 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 19 7 International postal approval DRC D3 transmitters and receivers in the standard delivery form can be operated without any registration or operating fee in the following countries:

Frequency range 2,4-GHz ISM band Countries Austria Belgium Bulgaria Croatia Cyprus Czech Republic Denmark Estonia Finland France Germany Greece Hungary Iceland Ireland Italy Latvia Liechtenstein Lithuania Luxembourg Malta Netherlands Norway Poland Portugal Romania Slovakia Slovenia Spain Sweden Switzerland United Kingdom H b m G S P H M x e r e T 20 4 1 0 1 5 1

/

d d n i

. 4 4 7 6 2 1 1 2 Original EC conformity declaration in the meaning of EC Directive 2006/95/EG, Annex III Ident. number / Language 19968044 / EN Issue 0714 Page 1/ 1 Hereby we, Terex MHPS GmbH Forststrasse 16, 40597 Dsseldorf, Germany declare that the radio control system for cranes and hoists Demag DRC, consisting of:

DRC -10 transmitter DRC-J transmitter DRC-DR receiver DRC-MP receiver Ident. no. 773 591 44 Ident. no. 773 593 44 Ident. no. 719 439 44 Ident. no. 773 594 44 of serial design are in conformity with the provisions of the following relevant regulation:

EC Low Voltage Directive 2006/95/EC The product additionally complies with the following relevant directives/provisions:

EC EMC Directive EC RTTE Directive 2004/108/EC 1999/5/EC Applied harmonised standards and/or C standard drafts, in particular:

Cranes - Control elements and control positions Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design Stop function: Category 3, PL d Cranes - Power driven winches and hoists -

Part 2: Power driven hoists Safety of machinery - Electrical equipment of machines - Part 32:

Requirements for hoisting machines EN 13557 EN ISO 13849-1 EN 14492-2 EN 60204-32 Wetter, 21.11.2014 i.V. Dr. Thomas Bnker Business Line Components i.V. Dirk Schulte Handling Technology & Drives Engineering & Development U02180 Subject to change. No liability for errors or omissions Terex Material Handling P FCC and Industry Canada Information FCC information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Industry Canada Information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. CAN ICES-3 (A)/NMB-3(A) The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Heath Canadas website www.hc-sc.gc.ca/rpb. Lantenne (s) utilise pour cet metteur doit tre install pour fournir une distance de sparation dau moins 20 cm de toute personne et ne doit pas tre co-localises ou oprant en conjonction avec une autre antenne ou metteur. L'installateur de cet quipement radio doit veiller ce que l'antenne est situe ou oriente de faon qu'il ne dgage pas de champ RF dpassant les limites de Sant Canada pour la population gnrale;

Consultez le Code de scurit 6, disponible sur le site web de www.hc-sc.gc.ca/rpb de Sant Canada. 22 H b m G S P H M x e r e T 4 1 0 1 5 1 d d n

/

i

. 4 4 7 6 2 1 1 2 The current addresses of our sales offices, subsidiaries and agencies worldwide can be found on the Terex MHPS GmbH homepage at www.demagcranes.com/Contact Terex MHPS GmbH PO Box 67 58286 Wetter (Germany) Phone +49 (0)2335 92-0 Fax www.demagcranes.com

+49 (0)2335 92-7676 y n a m r e G n i Reproduction in whole or in part only with prior consent of Terex MHPS GmbH, 58286 Wetter (Germany) Subject to change. Not liable for errors or omissions. d e t n i r P