FCC ID: 2AUCU-22102Z Z-WAVE+ 600W DIMMER SINGLE POLE

Instruction Bulletin Boletn de instrucciones Directives d'utilisation SQR22102WHZ, SQR22102LAZ, SQR22102BKZ Z-Wave 600 W Dimmer Spanish French Retain for future use. / Conservar para uso futuro. / conserver pour usage ultrieur. Replaces / Reemplaza / Remplace GDE77979, 09/2020 GDE77979 Rev. 01, 05/2021 Caractersticas Caractristiques La tecnologa inalmbrica Z-Wave crea una red de malla para la interoperabilidad de comandos y controles con otros controladores y dispositivos compatibles con Z-Wave. La technologie sans fil Z-Wave cre un rseau maill pour assurer linteroprabilit du commandement et des commandes avec dautres tlcommandes et dispositifs compatibles avec Z-Wave. La opcin de nivel de intensidad preestablecida permite que el atenuador se encienda en el mismo nivel de intensidad que se haba establecido cuando la luz estaba encendida. Loption de niveau de lumire prrgl permet dallumer le gradateur au dernier niveau de lumire rgl. Features Wireless Z-Wave technology creates a mesh network for command and control interoperability with other Z-Wave compliant controllers and devices. Manual and remote on/off and dimming control of any installed incandescent or dimmable LED. Preset light level option allows the dimmer to turn on to the light level that was adjusted previously when the light was on. Double tap paddle adjusts light to full brightness without affecting preset levels. Programmable rapid start feature ensures lamp start-up even at low dim levels. Adjustable high level trim setting for additional energy savings. Adjustable low level trim setting prevents flickering. Programmable fade up time. Programmable delayed OFF time. Three configurable power ON states. Supports over-the-air (OTA) upgrade. Child lockout capability. Sliding air gap switch meets UL requirements and allows the power to disconnect from the load locally. Single-pole or 3-way (multi-location) use. Measures the energy usage of the connected lighting and displays the actual consumption (in W) and the energy consumed (in kWh) in the user interface of the gateway. NOTE:

The LED dimming performance may vary based on dimmer type, model, manufacturer, circuit wiring, and circuit loading. Power ON state indicates the initial status of the device when it is powered on. Turn the device OFF to upgrade. For multi-location applications, a traditional mechanical switch or the Z-Wave wireless auxiliary switch, SQR50101**Z, could be used along with one Z-Wave master dimmer. Please refer to the gateway installation manual for energy usage display and energy measurement features. El interruptor deslizable con espacio de aire cumple con los requisitos UL y permite desconectar la alimentacin de la carga localmente. Mide el uso de energa de la iluminacin conectada, muestra el consumo real

(en W) y la energa consumida (en kWh) en la interfaz de usuario de la pasarela. Linterrupteur entrefer coulissant rpond aux exigences UL et permet de couper lalimentation de la charge au niveau local. Linterface utilisateur de la passerelle permet dafficher la consommation relle

(en W) et lnergie consomme (en kWh) de lclairage connect. NOTA:

REMARQUE :

El rendimiento del atenuador de LED puede variar segn el tipo, el modelo, el fabricante, el cableado del circuito y la carga del circuito. Les performances des DEL peuvent varier en fonction du type de gradateur, du modle, du fabricant, du cblage du circuit et de la charge du circuit. Consulte las funciones de indicacin del uso de energa y medicin de energa en el manual de instalacin de la pasarela. Veuillez vous reporter au guide dinstallation de la passerelle pour laffichage de la consommation dnergie et les fonctions de mesure de lnergie. SQR22102**Z Z-Wave 600 W Dimmer, Single-Pole, Energy Monitoring Specifications / Especificaciones de monitoreo de energa del atenuador unipolar de 600 W Z-Wave SQR22102**Z / Gradateur 600 W SQR22102**Z Z-Wave, unipolaire Spcifications de commande de lnergie1 Voltage / Tensin / Tension 120 Vac, 60 Hz / 120 Vca, 60 Hz / 120 V CA, 60 Hz Incandescent lights / Luces incandescentes / Voyants incandescence Dimmable LED lights / Luces LED regulables / clairages DEL gradables Operating temperature / Temperatura de operacin / Temprature de fonctionnement Supply Connection / Conexin de alimentacin / Raccordement l'alimentation Wireless Type / Tipo inalmbrico / Type sans fil Wireless Frequency / Frecuencia inalmbrica / Frquence radio 600 W 1.25 A (150 W) 32104F (040C) / De 32 F a 104 F (de 0 C a 40 C) / 32 104 F (0 40 C) 14 AWG 2 Z-Wave (Support S2 and SmartStart) / Z-Wave (admite S2 y SmartStart) / Z-Wave (prend en charge S2 et SmartStart) 908.40 MHz / 908.42 MHz / 916 MHz 1 ** = color code / cdigo de color / code de couleur : WH (white / blanco / blanc), LA (light almond / marfil / vert amande clair), BK (black / negro / noir) 2 Suitable for at least 167F (75C). / Apto para al menos 167 F (75 C). / Convient pour au moins 167 F (75 C). Precautions Precauciones Prcautions DANGER / PELIGRO / DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E, NOM-029-STPS-2011 or CSA Z462 or local equivalent. PELIGRO DE DESCARGA ELCTRICA, EXPLOSIN O DESTELLO POR ARQUEO Utilice equipo de proteccin personal (EPP) apropiado y siga las prcticas de RISQUE D'LECTROCUTION, D'EXPLOSION OU D'CLAIR D'ARC LECTRIQUE Portez un quipement de protection individuelle (PI) appropri et observez les seguridad elctrica establecidas por su Compaa, consulte la norma 70E de NFPA, NOM-029-STPS-2011 o CSA Z462 o la norma local equivalente. mthodes de travail lectrique scuritaire. Voir NFPA 70E, NOM-029-STPS-2011 ou CSA Z462 ou aux quivalents applicables dans votre region du monde. This equipment must only be installed and serviced by qualified Solamente el personal elctrico especializado deber instalar y prestar servicio de electrical personnel. mantenimiento a este equipo. Turn off all power supplying this equipment before working on or inside Desenergice el equipo antes de realizar cualquier trabajo en l. Siempre utilice un dispositivo detector de tensin nominal adecuado para confirmar la Always use a properly rated voltage sensing device to confirm power is desenergizacin del equipo. To reduce the risk of overheating and possible equipment damage, do not install to control a receptacle, a motor-operated appliance, a fluorescent lighting fixture, or a transformer-supplied appliance. para controlar un receptculo, un artefacto que funcione mediante motor, un dispositivo de iluminacin fluorescente o un artefacto con suministro de un transformador. Para reducir el riesgo de sobrecalentamiento y posibles daos al equipo, no lo instale equipment. off. Use with copper wire only. Replace all devices, doors, and covers before turning on power to this Indoor use only. Use solo con conductores de cobre. Para uso en interiores solamente. Vuelva a colocar todos los dispositivos, las puertas y las cubiertas antes de volver a sous tension. equipment. energizar el equipo. Seul un personnel qualifi doit effectuer l'installation et l'entretien de cet appareil. Coupez l'alimentation de l'appareil avant d'y travailler. Utilisez toujours un dispositif de dtection de tension ayant une valeur nominale approprie pour vous assurer que l'alimentation est coupe. Pour rduire le risque de surchauffe et de dommages ventuels lappareil, nutilisez pas pour contrler une prise de courant, un appareil motoris, un appareil dclairage fluorescent ou un appareil aliment par transformateur. utiliser avec des fils en cuivre uniquement. Pour usage l'intrieur seulement. Replacez tous les dispositifs, les portes et les couvercles avant de mettre l'appareil Failure to follow these instructions will result in death or serious injury. El incumplimiento de estas instrucciones podr causar la muerte o lesiones serias. Si ces directives ne sont pas respectes, cela entranera la mort ou des blessures graves. WARNING / ADVERTENCIA / AVERTISSEMENT HAZARD OF HEAT AND FIRE DAMAGE Read all instructions before installation. The manufacturer will not be held responsible for product damage resulting from not following the instructions. Wet hands are strictly prohibited. Work strictly according to the rated load. PELIGRO DE DAO POR CALENTAMIENTO E INCENDIO Lea todas las instrucciones antes de la instalacin. El fabricante no ser responsable por los daos causados al producto por no seguir las instrucciones. Est estrictamente prohibido tener las manos mojadas. Trabaje estrictamente de acuerdo con la carga nominal. No siga trabajando si se produce un desmontaje de cualquier naturaleza, o dao por Do not continue working after self-disassembly of any nature and fuerzas externas. damage of external forces. RISQUE DE DOMMAGE CAUS PAR LA CHALEUR ET LE FEU Lisez toutes les instructions avant linstallation. Le fabricant ne pourra pas tre tenu responsable des dgts causs au produit qui peuvent survenir si ces instructions ne sont pas respectes. Il est strictement interdit de lutiliser avec les mains mouilles. Travaillez en respectant strictement la charge nominale !

Arrtez de travailler aprs une dsintgration accidentelle de quelque nature que ce soit et des dommages causs par des forces extrieures. Failure to follow these instructions can result in death, serious injury, or equipment damage. El incumplimiento de estas instrucciones puede causar la muerte, lesiones serias o dao al equipo. Si ces directives ne sont pas respectes, cela peut entraner la mort, des blessures graves ou des dommages matriels. SQR22102WHZ, SQR22102LAZ, SQR22102BKZ Z-Wave 600 W Dimmer Spanish French GDE77979 Rev. 01, 05/2021 HAZARD OF UNINTENDED USE This device is intended to be used for non-critical automation activities. It is not intended to support life, safety, or medical equipment. PELIGRO DE USO NO DESEADO Este receptculo device est destinado para uso en actividades de automatizacin no crticas. No est destinado para admitir equipos de soporte vital, seguridad o mdicos. RISQUE PROVENANT DUNE UTILISATION ACCIDENTELLE La prsente prise device doit tre utilise pour les activits dautomatisation non critiques. Elle n'est pas destine prendre en charge les quipements de survie, de scurit et mdicaux. Failure to follow these instructions can result in personal injury or equipment damage. El incumplimiento de estas instrucciones puede causar lesiones personales o dao al equipo. Si ces directives ne sont pas respectes, cela peut entraner des blessures ou des dommages matriels. CAUTION / PRECAUCIN / ATTENTION WARNING: This product can expose you to chemicals including Carbon black which is known to the State of California to cause cancer, and Bisphenol A (BPA), which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. ADVERTENCIA: Este producto puede exponerle a qumicos incluyendo negro de carbn, que son conocidos por el Estado de California como causantes de cncer, y Bisfenol A (BPA), que es conocido por el Estado de California como causante de defectos de nacimiento u otros daos reproductivos. Para mayor informacin, visite www.P65Warnings.ca.gov. AVERTISSEMENT: Ce produit peut vous exposer des agents chimiques, y compris le noir de carbone, identifi par l'tat de Californie comme pouvant causer le cancer, et le Bisphnol A (BPA), reconnu par l'tat de Californie comme pouvant causer des malformations congnitales ou autres troubles de l'appareil reproducteur. Pour de plus amples informations, prire de consulter www.P65Warnings.ca.gov. Wireless Range Conditions Condiciones de alcance inalmbrico Conditions de porte sans fil The wireless range is the effective distance of remote control and it will be impacted by the following conditions:

Each wall or obstacle (e.g., refrigerator, TV, etc.) between the remote or Z-Wave device and the destination device will reduce the wireless range. Brick, tile, or concrete walls block more of the wireless signal than walls made of wooden studs and plasterboard (drywall). The angle of direction between the remote or Z-Wave device and the destination device will also impact the wireless range; normally, placing the Z-Wave devices face-to-face will get the best wireless range. Wall-mounted Z-Wave devices installed in metal junction boxes may suffer a significant loss of range since the metal box blocks a large part of the wireless signal. El alcance inalmbrico es la distancia efectiva del control remoto y puede verse afectado por las siguientes condiciones:

Cada pared u obstculo (p. ej., el refrigerador, la televisin, entre otros) que se encuentre entre el control remoto o el dispositivo Z-Wave y el dispositivo de destino reducir el alcance inalmbrico. Las paredes de ladrillo, baldosas o concreto bloquean ms la seal inalmbrica que las paredes hechas de postes de madera y paneles de yeso (paneles de yeso). El ngulo de direccin entre el control remoto o el dispositivo Z-Wave y el dispositivo de destino tambin afectar el alcance inalmbrico; normalmente, si se colocan los dispositivos Z-Wave uno frente al otro se obtendr el mejor alcance inalmbrico. Los dispositivos Z-Wave montados en la pared e instalados en cajas de conexiones metlicas pueden sufrir una prdida significativa de alcance, ya que la caja metlica bloquea gran parte de la seal inalmbrica. La porte sans fil est la distance laquelle la tlcommande peut fonctionner et elle sera affecte par les conditions suivantes :

Chaque mur ou obstacle (par exemple, rfrigrateur, tlviseur, etc.) entre la tlcommande ou l'appareil Z-Wave et lappareil de destination rduira la porte sans fil. Les murs de brique, de carreaux ou de bton bloquent plus de signal sans fil que les murs faits de poteaux en bois et de placopltre (cloisons sches). Langle entre la tlcommande ou l'appareil Z-Wave et lappareil de destination aura galement un impact sur la porte sans fil. En principe, on obtient une meilleure porte sans fil en plaant les appareils Z-Wave face face. Les appareils muraux Z-Wave installs dans des botes de jonction en mtal peuvent subir une perte importante de porte, car la bote en mtal bloque une grande partie du signal sans fil. Installation Instalacin Installation 1. Turn the power off at circuit breaker or fuse and test that power is off, 1. Desconecte la alimentacin en el interruptor automtico o fusible y, antes de with a properly rated voltage sensing device, before wiring. 2. Wire the dimmer according to the appropriate wiring diagram

(Figure 1 or 2). realizar el cableado, compruebe que la alimentacin est desconectada usando un dispositivo detector de voltaje nominal adecuado. 2. Conecte el atenuador de intensidad segn el diagrama de cableado adecuado 1. Avant de procder au raccordement, coupez le courant au niveau du disjoncteur ou du fusible et vrifiez que lalimentation est bien coupe laide dun dispositif de dtection de tension correctement calibr. 2. Raccordez le gradateur selon le schma de cblage appropri (Figure 1 ou 2). NOTE: There is not a wire between the Z-Wave master device and the auxiliary switch in 3-way control using the Z-Wave auxiliary switch SQR50101**Z. Please refer to the SQR50101**Z user manual for the wiring diagram of the auxiliary switch itself.

(Figura 1 o 2). NOTA:

3. Check that all connections are tight and no bare wires exposed. Install the dimmer into the standard outlet box using the screws 4. provided. 3. Verifique que todas las conexiones estn apretadas y no haya conductores 4. desnudos expuestos. Instale el atenuador de intensidad en la caja de tomacorriente estndar con los tornillos provistos. REMARQUE :

3. Vrifiez que tous les raccordements sont bien serrs et quaucun fil dnud nest dcouvert. Installez le gradateur dans la bote de la sortie standard laide des vis fournies. 4. Figure / Figura / Figure 1 :

Z-Wave Plus Dimmer Single-Pole Wiring Diagram /

Wire connector /

Conector de conductores /

Capuchon de connexion Outlet box /

Caja de tomacorrriente /

Bote de sortie L G H L O A D H O T N R E L E V A R T L A R T U E N L G N LOAD /

CARGA /

CHARGE H Hot / Fase / Actif N Neutral / Neutro / Neutre G Ground / Tierra / Terre L Load / Carga / Charge About wire connections: /

Sobre conexiones del cable: /

propos des connexions de fils :

1/2 in. (12.7 mm) /

1/2 pulg. (12.7 mm) /

1/2 po (12,7 mm) Back wire / Conductor posterior /

Fil arrire Figure / Figura / Figure 2 :

Z-Wave Plus Dimmer 3-Way Wiring Diagram with Traditional Mechanical Switch /

Wire connector /

Conector de conductores /

Capuchon de connexion G G Outlet Box /

Caja de tomacorriente /

Bote de sortie T L N H L O A D H O T R E L E V A R T L A R T U E N L G N LOAD /

CARGA /

CHARGE Outlet Box /

Caja de tomacorriente /

Bote de sortie G T N SQR22102**Z Mechanical Switch H N T G L Hot / Fase / Actif Neutral / Neutro / Neutre Traveler / Cable viajero / Fil de voyageur Ground / Tierra / Terre Load / Carga / Charge Install the wall plate (not included) (Figure 3). 5. 6. Restore power. Instale la placa de pared (no incluida) (Figura 3). 5. 6. Restaure la alimentacin. Installez la plaque murale (non incluse) (Figure 3). 5. 6. Rtablissez lalimentation. 2 20202021 Schneider Electric All Rights Reserved / Reservados todos los derechos / Tous droits rservs GDE77979 Rev. 01, 05/2021 Figure / Figura / Figure 3 :

Wall Plates / Placas de pared / Plaques murales SQR22102WHZ, SQR22102LAZ, SQR22102BKZ Z-Wave 600 W Dimmer Spanish French X Series /

Serie X /

Srie X XD Series /

Serie XD /

Srie XD XD Series Multigang /

Interruptor mltiple Serie XD /

Sries XD multiprise or SQWVS22101**Z SQWVM22101**Z

** = color code / cdigo de color / code de couleur :

WH (white / blanco / blanc) LA (light almond / marfil / vert amande claire) BK (black / negro / noir) GY (gray / gris / gris) Only for installation of XD series cover plate. /

Solo para la instalacin de la placa de cubierta de la serie XD. /

Uniquement pour linstallation du couvercle de la srie XD. NOTE: When installing more than one dimmer in the same wall box, the maximum load capacity will be reduced, please refer to Tables 1and 2. NOTA:

REMARQUE :

Table / Tabla / Tableau 1 :

Load Type /

Single Load Type / Tipo de carga nica /

Type de charge unique Maximum Load Rating / Valor nominal mximo de carga / Limite de charge maximale Derating for Multiple 2-Gang /

Reduccin de valor nominal para dos interruptores /

Dclassement pour plaque murale double Derating for Multigang / Reduccin de valor nominal para interruptores mltiples / Dclassement pour jumelage multiple Incandescent lamp / Lmpara incandescente / Lampe incandescence Dimmable LED / LED regulable / DEL rglable 600 W 150 W 500 W 150 W 400 W 150 W Table / Tabla / Tableau 2 :

Combined Bulb Type / Tipo de bombilla combinada / Type ampoules combines Then the maximum COMBINED wattage for the incandescent bulbs:

LED Bulbs /

0 W 125 W 2650 W 5175 W 76100 W 101125 W 126150 W 600 W 500 W 400 W 300 W 200 W 100 W 0 W Operation 1. Air gap switch (Figure 4) Operacin Utilisation 1. Interruptor con espacio de aire (Figura 4) 1. Interrupteur entrefer (Figure 4) The dimmer has an air gap switch on the lower side to completely disconnect power to the load. Slide the air gap switch to the left to disconnect the power while replacing light bulbs. Slide it to the right for normal operation. The air gap switch must be all the way in for the dimmer to function and control the lighting. El atenuador de intensidad tiene un interruptor con espacio de aire en la parte inferior para desconectar por completo la alimentacin a la carga. Deslice el interruptor con espacio de aire hacia la izquierda para desconectar la alimentacin mientras reemplaza las bombillas. Deslcelo hacia la derecha para volver al funcionamiento normal. El interruptor con espacio de aire debe estar en la posicin correcta para que el atenuador de intensidad funcione y controle la iluminacin. Le gradateur est dot dun interrupteur entrefer sur le ct infrieur permettant de mettre compltement hors tension la charge. Faites coulisser linterrupteur entrefer vers la gauche pour couper le courant pendant que vous remplacez les ampoules. Faites-le coulisser vers la droite pour rtablir le fonctionnement normal. Linterrupteur entrefer doit tre enclench fond pour que le gradateur puisse fonctionner et commander lclairage. Figure / Figura / Figure 4 :

Air Gap Switch / Interruptor con espacio de aire / Interrupteur dentrefer QR code / Cdigo QR / Code QR Pin code / Cdigo de pin / Code NIP 2 S E V A W

Z PIN Code XXXXX SQR22101**Z On: dim up paddle /

Encendido: paleta para aumentar la intensidad /

Sous tension : augmentation Off: dim down paddle /

Apagado: paleta para disminuir la intensidad /

Hors tension : diminution LED indicator / Indicador LED / Voyant DEL Reset button /

t e s e R Air gap switch /

Interruptor con espacio de aire /

Interrupteur dentrefer Power off /

Desenergice el equipo /

Coupez lalimentation Power on /

Alimentacin conectada /

Sous tension 2. Local control ON/OFF control (Figure 5):

One short tap on the upper paddle to turn on the lighting to the last brightness setting. One short tap on the lower paddle to turn off the lighting. Figure / Figura / Figure 5 :

Local Control: ON/OFF Control /

2. Control local 2. Commande locale Turn lighting on /

Encender la luz /

clairage allum Turn lighting off /

Apagar la luz /

clairage teint Tap (short press) /

Tocar (presione brevemente) /

Appuyez (lgre pression) Dimming control (Figure 6):

Long press on upper paddle to dim up the lighting. Long press on lower paddle to dim down the lighting. 20202021 Schneider Electric All Rights Reserved / Reservados todos los derechos / Tous droits rservs 3 SQR22102WHZ, SQR22102LAZ, SQR22102BKZ Z-Wave 600 W Dimmer Spanish French Figure / Figura / Figure 6 :

Local Control: Dimming Control /

GDE77979 Rev. 01, 05/2021 Quick to full brightness (Figure 7):

Double taps on any paddle to turn on the lighting to full brightness. Figure / Figura / Figure 7 :

Local Control: Quick to Full Brightness /

Brighten lighting /

Ilumina brillosa /

clairage de forte intensit Dim lighting /

Iluminacin tenue /

clairage de faible intensit Press and hold /

Mantenga pulsado /

Appuyez et maintenez Maximum brightness / Spa / Fre or Double taps on either paddle / Spa / Fre 3. Group control the nodes of association group 2 (Figure 8) 3. Control en grupo de los nodos del grupo de asociacin 2:

3. Contrle de groupe des nuds du groupe dassociation 2 :

Press the upper and lower paddles at the same time:

Short press to turn on or turn off. Long press to dim up or dim down. NOTE:

Please refer to association setting for nodes group 2 setup. This requires a gateway with advanced features and assumes the device is included in a network. It is recommended that dimmer devices be grouped together into the same group so that group control can manage normal dimming function. NOTA:

Figure / Figura / Figure 8 :

Group Control / Control en Grupo / Contrle de Groupe REMARQUE :

Short press on both paddles /

Long press on both paddles /

4. 3-Way control (Table 3) 4. 4. Table / Tabla / Tableau 3 :

3-Way Control /

Action /

Turn on the light /

Turn off the light /

Dim up the light /

Dim down the light /

Connected 3-Way Switch /

Traditional Mechanical Switch (wired) /

Press to another state /

SQR50101**Z Z-Wave AUX Switch (wireless) /

Tap upper paddle /

Tap lower paddle /

Long press the upper paddle /

Long press the lower paddle /

5. Inclusion to a Z-Wave network:

4. Inclusin en una red Z-Wave:

4. Intgration dans un rseau Z-Wave :

NOTE: The dimmer supports S2-authenticated and S2-unauthenticated inclusion methods. It is highly recommended to only select S2-authenticated or the highest inclusion method, and deselect other methods. This ensures the highest security level during Z-Wave service. During S2-authenticated inclusion, users may be asked to scan the QR code or enter a 5-digit pin code attached on the device. NOTA: El atenuador de intensidad admite los mtodos de inclusin con autenticacin S2 y sin autenticacin S2. Lo ms recomendado es seleccionar solo el mtodo de inclusin con autenticacin S2 o el mtodo de inclusin ms alto y anular la seleccin de otros mtodos. Esto garantiza el nivel de seguridad mximo durante el servicio Z-Wave. Durante la inclusin con autenticacin S2, se puede solicitar a los usuarios que escaneen el cdigo QR o ingresen el cdigo pin de cinco dgitos adjunto en el dispositivo. REMARQUE : Le gradateur prend en charge les mthodes dinclusion authentifies S2 et non authentifies S2. Il est fortement recommand de slectionner uniquement la mthode dintgration authentifie S2 ou la plus leve et de dcocher les autres mthodes. Cela garantit un niveau de scurit trs lev lors du fonctionnement du dispositif Z-Wave. Pendant lopration dintgration authentifie S2, les utilisateurs peuvent tre invits numriser le code QR ou saisir le code NIP 5 chiffres figurant sur lappareil. A. SmartStart inclusion: This feature requires that the gateway has A. Inclusin de SmartStart:

A. Intgration SmartStart :

implemented SmartStart. Use the APP of the gateway or the gateway camera to scan the QR code (located on the device or on the enclosed label in the package) before powering on the device. Once the device is powered on, it shall automatically be added to the gateway. B. Manual inclusion (Figure 9): When the gateway is in adding mode

(please refer to the instruction of the Z-Wave gateway for the operations on the gateway itself), click any paddle quickly within 1.5 seconds. NOTE: Please do not power cycle the device during the inclusion process. NOTA: No reinicie el dispositivo durante el proceso de inclusin. REMARQUE : Ne cyclez jamais lalimentation de lappareil pendant le processus dinclusion. Figure / Figura / Figure 9 :

Join or Leave the Z-Wave Network / nase o salga de la red Z-Wave / Rejoindre ou quitter le rseau Z-Wave B. Inclusin manual (Figura 9): Cuando la pasarela est en modo de adicin (consulte las operaciones en la pasarela en las instrucciones de la pasarela Z-Wave). B. Intgration manuelle (Figure 9) : Lorsque la passerelle est en mode d'ajout

(veuillez vous reporter aux instructions de la passerelle Z-Wave pour les oprations sur la passerelle elle-mme). or/

o/

ou Quick click x3, within 1.5 s, interval <0.5s /

Clic rpido 3 veces en 1,5 s o en un intervalo de tiempo menor a 0,5 s /

Cliquez rapidement trois fois en 1,5 s ou dans un intervalle infrieur 0,5 s 4 20202021 Schneider Electric All Rights Reserved / Reservados todos los derechos / Tous droits rservs GDE77979 Rev. 01, 05/2021 SQR22102WHZ, SQR22102LAZ, SQR22102BKZ Z-Wave 600 W Dimmer Spanish French 5. Exclusion from a Z-Wave network (Figure 9): When the gateway is in removing mode (please refer to the instruction of the Z-Wave gateway for the operations on the gateway itself), click any paddle quickly within 1.5 seconds. 6. Remote control: After the device is included in a Z-Wave gateway, the gateway can provide control of an individual device, groups of devices and scenes, and offers flexibility in setting up the lighting control network. Please refer to the gateway instructions for details. 7. Reset to factory defaults (Figure 10). 5. Exclusin de una red Z-Wave (Figura 9): Cuando la pasarela est en modo de extraccin (consulte las operaciones en la pasarela en las instrucciones de la pasarela Z-Wave). 6. Control remoto: despus de que el dispositivo se incluye en una pasarela Z-Wave, la pasarela puede proporcionar el control de un dispositivo individual, grupos de dispositivos y escenas, y ofrece flexibilidad para configurar la red de control de iluminacin. Consulte los detalles en las instrucciones de la pasarela. 5. Exclusion du rseau Z-Wave (Figure 9) : Lorsque la passerelle est en mode de retrait (veuillez vous reporter aux instructions de la passerelle Z-Wave pour les oprations sur la passerelle elle-me). Tlcommande : Une fois que lappareil est intgr dans la passerelle Z-Wave, celle-

ci peut contrler un seul appareil, des groupes dappareils et des scnes, et offre une flexibilit dans la configuration du rseau de commande dclairage. Veuillez-vous reporter aux instructions de la passerelle pour obtenir plus de dtails. 6. 7. Restablezca los valores predeterminados de fbrica:

7. Rtablir les paramtres par dfaut :

Figure / Figura / Figure 10 :

Reset to Factory Defaults / Restablezca los valores predeterminados de fbrica / Rtablir les paramtres par dfaut Reset button / Spa / Fre Long press >20s / Spa / Fre t e s e R NOTE:

Use this procedure only when the Z-Wave gateway is missing or otherwise inoperable. Reset the dimmer to factory default settings will set the dimmer to not in Z-Wave network state, delete the association setting, and restore the configuration setting to the default. NOTA:

Utilice este procedimiento solo si falta o no funciona la pasarela Z-Wave. Al restablecer el atenuador de intensidad a la configuracin predeterminada de fbrica, este se establecer en estado de no red Z-Wave, se eliminar la configuracin de asociacin y se restablecer la configuracin predeterminada. Une telle dmarche nest envisageable que lorsque la passerelle Z-Wave est manquante ou hors dusage. La rinitialisation du gradateur aux rglages dusine dsactive le mode Z-Wave, supprime le rglage dassociation et rtablit la configuration par dfaut. REMARQUE :

Advanced Setting Configuracin avanzada Paramtres avancs The advanced setting requires an advanced gateway. Basic gateway does not support this setting. Users can do the setting through the interface of the advanced gateway. Para la configuracin avanzada se requiere una pasarela avanzada. La pasarela bsica no admite esta configuracin. Los usuarios pueden realizar la configuracin a travs de la interfaz de la pasarela avanzada. Les paramtres avancs ncessitent une passerelle avance. La passerelle de base ne prend pas en charge ces paramtres. Les utilisateurs peuvent effectuer le rglage via linterface de la passerelle avance. All configuration parameters can be restored to factory default settings by the gateway or by manual reset. Todos los parmetros de configuracin se pueden restaurar a los valores predeterminados de fbrica mediante la pasarela o mediante el restablecimiento manual. Tous les paramtres de configuration peuvent tre restaurs aux paramtres par dfaut via la passerelle ou par une rinitialisation manuelle. Configuration / Configuracin / Configuration Parameter No. /

Nm. de parmetro /

Numro de paramtre Size /

Tamao /

Taille Description /

Descripcin /

Description Valid Value /

Valor vlido /

Valeur valide Default Value /

Valor predeterminado /

Valeur par dfaut Unit /

Synchronization of load power and LED indicator /

Sincronizacin de la alimentacin de carga y el indicador LED / Synchronisation de l'alimentation de la charge et du voyant DEL 0 = Power ON, LED OFF / Power OFF, LED ON /

0 = Alimentacin CONECTADA, LED APAGADO / Alimentacin DESCONECTADA, LED ENCENDIDO /

0 = Sous tension, DEL teinte / Hors tension, DEL allume 1 = Power ON, LED ON / Power OFF, LED OFF /

1 = Alimentacin CONECTADA, LED ENCENDIDO / Alimentacin DESCONECTADA, LED APAGADO /

1 = Sous tension, DEL allume / Hors tension, DEL teinte 1 2 3 4 5 6 7 8 1 2 Fade Up Time (the time from OFF to full brightness) /

1 byte /

1 byte /

1 octet 1 byte /

1 byte /

1 octet 1 byte /

1 byte /

1 octet 1 byte /

1 byte /

1 octet 2 bytes /

2 byte /

2 octet 1 byte /

1 byte /

1 octet 1 byte /

1 byte /

1 octet 1 byte /

1 byte /

1 octet Delay OFF Time /

Power ON Status /

Child Lockout /

Rapid Start /

Set Min. Dimming Level /

Set Max. Dimming Level /

5 5 0~240 1 = OFF /

2 = ON (full brightness) /

3 = Last state /

0 = Disable 1 = Enable 0~1800 0 = Disable /

1 = Enable /

1~45 55~99 Association / Asociacin / Association Grouping ID / Id. de agrupamiento / Code d'identification de groupe Maximum No. of Nodes / Nmero mximo de nodos / Nombre maximal de nuds Description / Descripcin / Description 1. Switch Multilevel Report /

2. Meter Report /

3. Device Reset Locally /

Basic Set /

LED Indication / Indicacin LED / Indication DEL Blue LED flashing /

Luz LED azul parpadeando /

Un voyant DEL bleu clignote. LED blinking slowly for 3 minutes (one blink per 3 seconds): device not in network / El LED parpadea lentamente durante 3 minutos (un parpadeo cada 3 segundos): el dispositivo no est en la red. / DEL clignotant lentement pendant 3 minutes (un clignotement toutes les 3 secondes) : lappareil nest pas en rseau. LED stays on for 1 minute: device in the network / La luz LED se mantiene durante un minuto: device in the network / Le voyant DEL reste allum pendant 1 minute : device in the network. LED blinking fast (one blink per second): adding/leaving network / El LED parpadea rpidamente (un parpadeo por segundo): agregando a la red/saliendo de la red. / DEL clignotant rapidement (un clignotement par seconde) : mise en/hors rseau. LED blinking 3 times within one second: signal for releasing the reset button. /

LED blinking 4 times within 2 seconds: start to perform reset process. /

LED blinking 5 seconds (twice per second): device receiving OTA command or OTA unsuccessful. /

Blue LED on / LED azul encendido / Le voyant DEL bleu est allum. Device is turned on (default setting, can be configured). / El atenuador de intensidad est activado (configuracin de fbrica, se puede configurar). / Le gradateur est activ (rglage par dfaut; peut tre configur). Blue LED off / LED azul apagado / Le voyant DEL bleu est teint. Device is turned off (default setting, can be configured). / El atenuador de intensidad est desactivado (configuracin predeterminada, se puede configurar). / Le gradateur est dsactiv (rglage par dfaut; peut tre configur). 1 0 1 0 3 0 1 99 Second /

Second /

20202021 Schneider Electric All Rights Reserved / Reservados todos los derechos / Tous droits rservs 5 SQR22102WHZ, SQR22102LAZ, SQR22102BKZ Z-Wave 600 W Dimmer Spanish French GDE77979 Rev. 01, 05/2021 Troubleshooting Resolucin de problemas Dpannage Issue / Problema / Problme Solution / Solucin / Solution SmartStart inclusion taking too long / La inclusin de SmartStart tarda demasiado / Lintgration SmartStart prend trop de temps Power cycle the dimmer to escalate inclusion. / Apague y encienda el atenuador de intensidad para reforzar la inclusin. / teindre et rallumer le gradateur pour intensifier le processus dintgration. Inclusion is unsuccessful / No se logr la inclusin / Lintgration a chou. Move the gateway closer to the device and repeat the inclusion operation. / Mueva la pasarela cerca del atenuador de intensidad y repita la operacin de inclusin. / Rapprochez la passerelle du gradateur et rptez lopration dinclusion. Lights flickering / Iluminacin intermitente / Voyants clignotants Lamp has bad connection. / La lmpara est mal conectada. / La connexion de la lampe est mauvaise. Wires not secured firmly with wire connectors. / Los conductores no estn sujetos firmemente con los conectores. / Les fils ne sont pas fixs solidement aux connecteurs de fils. LED flickers at low end of dimming range / El LED parpadea en el extremo inferior del rango de regulacin. / La DEL clignote la limite infrieure de la plage de gradation Increase the low end of the dimming range. /

LED bulb flickers throughout dimming range / La bombilla LED parpadea en todo el rango de regulacin. / Lampoule DEL clignote sur toute la plage de gradation. Ensure the bulbs are marked dimmable. Refer to recommended dimmable LED bulbs at www.se.com. / Asegrese de que las bombillas sean regulables. Consulte las bombillas LED regulables recomendadas en www.se.com. / Vrifiez que la mention Rglable figure sur les ampoules. Consultez les ampoules DEL rglables recommandes sur le site www.se.com. Circuit breaker or fuse has tripped. / El interruptor automtico o fusible se ha disparado. / Le disjoncteur ou le fusible sest dclench. Light does not turn ON / La luz no se enciende. / La lampe ne sALLUME pas. Lamp is burned out. / La lmpara est quemada. / La lampe est grille. Lamp or dimmer neutral connection is not wired. / La conexin neutra de la lmpara o del interruptor regulador no est cableada. / La lampe ou la connexion du neutre du gradateur nest pas cble. FCC Compliance Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses, generates and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. RF Exposure: A distance of 20 cm shall be maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. Non-modification statement Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. FCC Suppliers Declaration of Conformity Product Name: ZWAVE + 600W DIMMER SINGLE POLE Model number: SQR22102WHZ, SQR22102LAZ, SQR22102BKZ Suppliers Name: Schneider Electric Suppliers Address (USA): 800 Federal Street Andover, MA 01810 USA Suppliers Website: www.se.com/us FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ISED Statement / Dclaration dISED Model numbers: SQR22102WHZ, SQR22102LAZ, SQR22102BKZ This Class [B] digital apparatus complies with Canadian CAN ICES-003(B). This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and any part of your body. Cet appareil numrique de la classe [B] est conforme la norme NMB-003(B) du Canada. Ce dispositif contient un ou plusieurs metteurs/rcepteurs exempts de licence qui sont conformes au(x) RSS exempt(s) de licence dInnovation, Science et Dveloppement conomique Canada. Son fonctionnement est soumis aux deux conditions suivantes :

1. L'appareil ne doit pas produire de brouillage. 2. L'appareil doit accepter toutes les interfrences reues, notamment celles lorigine dun fonctionnement indsirable. Pour se conformer aux exigences de conformit CNR 102 RF exposition, une distance de sparation d'au moins 20 cm doit tre maintenue entre l'antenne de cet appareil et toutes les personnes. Warranty Information / Informacin importante / Renseignements sur la garantie Schneider Electric warranties its products to be free of defects in materials and workmanship for a period of two (2) years. There are no obligations or liabilities on the part of Schneider Electric for consequential damages arising out of or in connection with the use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. Schneider Electric garantiza que sus productos estarn libres de defectos en materiales y mano de obra por un perodo de dos (2) aos. No hay obligaciones ni responsabilidades por parte de Schneider Electric por daos consecuentes que surjan o estn relacionados con el uso o el rendimiento de este producto u otros daos indirectos con respecto a la prdida de propiedad, los ingresos o las ganancias, o al costo de remocin, instalacin o reinstalacin. Schneider Electric garantit que ses produits sont exempts de dfauts de matriaux et de fabrication pour une priode de deux (2) ans. Schneider Electric na aucune obligation ni responsabilit lgard des dommages indirects dcoulant de lutilisation de ce produit ou en rapport avec celle-ci, ni dautres dommages indirects rsultant de la perte de biens, de revenus ou de profits, ou des frais de retrait, dinstallation ou de rinstallation. Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. Solamente el personal calificado deber instalar, hacer funcionar y prestar servicios de mantenimiento al equipo elctrico. Schneider Electric no asume responsabilidad alguna por las consecuencias emergentes de la utilizacin de este material. Seul un personnel qualifi doit effectuer linstallation, lutilisation, lentretien et la maintenance du matriel lectrique. Schneider Electric nassume aucune responsabilit des consquences ventuelles dcoulant de lutilisation de cette documentation. Schneider Electric and Square D are trademarks and the property of Schneider Electric SE, its subsidiaries, and affiliated companies. All other trademarks are the property of their respective owners. Schneider Electric y Square D son marcas comerciales y propiedad de Schneider Electric SE, sus filiales y compaas afiliadas. Todas las otras marcas comerciales son propiedad de sus respectivos propietarios. Schneider Electric et Square D sont des marques commerciales et la proprit de Schneider Electric SE, ses filiales et compagnies affilies. Toutes les autres marques commerciales sont la proprit de leurs propritaires respectifs. Schneider Electric USA, Inc. 800 Federal Street Andover, MA 01810 USA 888-778-2733 www.se.com/us 6 Importado en Mxico por:

Schneider Electric Mxico, S.A. de C.V. Av. Ejercito Nacional No. 904 Col. Palmas, Polanco 11560 Mxico, D.F. 55-5804-5000 www.se.com/mx Schneider Electric Canada, Inc. 5985 McLaughlin Road Mississauga, ON L5R 1B8 Canada 800-565-6699 www.se.com/ca 20202021 Schneider Electric All Rights Reserved / Reservados todos los derechos / Tous droits rservs

(10 mm) 7. MINIMUM SIZE:

(10 mm) FONT SIZE:

XXXXX ( > 5 pt)

(10 mm) R E L E V A R T L A R T U E N L O A D H O T E513233 Energy Monitoring For supply connections, use 12-14 AWG wires rated for at least 75C FCC ID : 2AUCU-22102Z IC: 25381-22102Z CAN ICES-003(B)/NMB-003(B) STRIP GAUGE 1/2 inch Made in China 2 S E V A W

Z PIN Code XXXXX SQR22102LAZ t e s e R MARKING DETAIL Z-WAVE PLUS DIMMER 5. MINIMUM SIZE:

(11mm)

(Z-WAVE Logo Color: Black) All Laser Marking MARKING DETAIL Z-WAVE PLUS DIMMER

(10 mm) 7. MINIMUM SIZE:

(10 mm) FONT SIZE:

XXXXX ( > 5 pt)

(10 mm) R E L E V A R T L A R T U E N L O A D H O T E513233 Energy Monitoring For supply connections, use 12-14 AWG wires rated for at least 75C FCC ID : 2AUCU-22102Z IC: 25381-22102Z CAN ICES-003(B)/NMB-003(B) STRIP GAUGE 1/2 inch Made in China 2 S E V A W

Z PIN Code XXXXX SQR22102WHZ t e s e R MARKING DETAIL Z-WAVE PLUS DIMMER 5. MINIMUM SIZE:

(11mm)

(Z-WAVE Logo Color: Black) All Laser Marking MARKING DETAIL Z-WAVE PLUS DIMMER

Schneider Electric (China) Co., Ltd., Shenzhen Branch Agent Authorization Company: Schneider Electric (China) Co., Ltd., Shenzhen Branch Address: Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation Zone, Qianhai, Shenzhen, China Product Name: Z-WAVE+ 600W DIMMER SINGLE POLE Model Number(s): SQR22102WHZ; SQR22102LAZ; SQR22102BKZ Product Description: Z-WAVE+ 600W DIMMER SINGLE POLE We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Date: Dec 1st, 2020 Signature:

Name:

Tony Huang Title:

Manager Company: Schneider Electric (China) Co., Ltd., Shenzhen Branch

Schneider Electric (China) Co., Ltd., Shenzhen Branch December 3, 2021 Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Ref:

FCC Class II Permissive change for FCC ID: 2AUCU-22102Z Applicant: Schneider Electric (China) Co., Ltd., Shenzhen Branch Dear Examiner, This is to request a Class II Permissive change for FCC ID: 2AUCU-22102Z originally granted on 1st July 2021 (date). The change under this application is to 1. Add R1 in circuit;

2. R7 is changed from R005 (5mR) to R002 (2mR);

3. L3 is changed from T68-26D-47Uh-0037A to LGH-220M-068125U;

4. Add a silicon pad between the toroid coil and enclosure, for purpose of thermal dissipation. I attest that the certified device will not be capable of ad-hoc mode operation outside of the grant conditions. Name: Tony Huang Date: 3rd DEC, 2021 Sincerely, Title: Manager Signature of applicant FCC Class II PC request letter Rev1_Z-WAVE DIMMER Internal

Schneider Electric (China) Co., Ltd., Shenzhen Branch Dec 1st, 2020 Federal Communications Commission Authorization and Evaluation Division FCC ID2AUCU-22102Z Confidentiality Request as outlined below:

1. Circuit Diagram Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the applicant hereby requests confidential treatment of information applied this application For 180 days pursuant to KDB 726920 D01. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, Company Name: Schneider Electric (China) Co., Ltd., Shenzhen Branch Contact Name: Tony Huang Title of PersonManager E-mail: zhiwen-tony.huang@se.com Zone, Qianhai, Shenzhen Address: Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation

Schneider Electric (China) Co., Ltd., Shenzhen Branch Address: Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation Zone, Qianhai, Shenzhen, China Confirmation Letter We, Schneider Electric (China) Co., Ltd., Shenzhen Branch The product: Z-WAVE+ 600W DIMMER SINGLE POLE FCC ID: 2AUCU-22102Z IC: 25381-22102Z SQR22102LAZ and SQR22102BKZ have the same technical construction including circuit diagram, PCB Layout, components and component layout, all electrical construction and mechanical construction with SQR22102WHZ. The difference lies only model number and color. ______________________ Company Name: Schneider Electric (China) Co., Ltd., Shenzhen Branch Contact Name: Tony Huang Address: Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation Zone, Qianhai, Shenzhen Date:12/16/2020

Schneider Electric (China) Co., Ltd., Shenzhen Branch Dec 1st, 2020 Federal Communications Commission Authorization and Evaluation Division FCC ID2AUCU-22102Z Confidentiality Request as outlined below:

1. Block Diagram 2. Circuit Diagram 3. Operational Description For 180 days pursuant to KDB 726920 D01. Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the applicant hereby requests confidential treatment of information applied this application The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, Company Name: Schneider Electric (China) Co., Ltd., Shenzhen Branch Contact Name: Tony Huang Title of PersonManager E-mail: zhiwen-tony.huang@se.com Zone, Qianhai, Shenzhen Address: Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation