FCC ID: MRXAFFPK4 TPMS Tire-PressureMonitoringSystem

SCHRADER ELECTRONICS.LTD.. MODEL :AFFPK4 USER MANUAL The TPMS Transmitter is installed to the valve stem in each tyre of a vehicle. The unit measures tyre pressure periodically and transmits this information by RF communication to a receiver inside the vehicle. In addition, the TPMS Transmitter performs the following functions:

Determines a temperature compensated pressure value. Determines any abnormal pressure variations in the wheel. Monitors the state of the Transmitters internal battery and informs the receiver of a low battery condition. Xtal:24 Mhz Fig 1: Sensor block diagram MODEL :AFFPK4 Fig 2: Schematic diagram MODEL :AFFPK4 Modulation During the Rotating Mode, The modulation used for the sensor is FSK (Frequency Shift Keying) with 50% Manchester bi-phase encoding. Modes Rotating Mode While the sensor/transmitter in the Rotating Mode, it shall satisfy the following requirements. The sensor/transmitter shall transmit an instantaneous measured data, if a pressure change of 2.0 psi from the last transmission or greater has occurred with respect to the following conditions. If the pressure change was a decrease of pressure, the sensor/transmitter shall transmit immediately every time it detects the 2.0-psi or greater pressure changes from the last transmission. If the pressure change of 2.0 psi or greater was an increase of pressure, the sensor shall not react to it. Stationary Mode While the sensor/transmitter in the Stationary Mode, it shall satisfy the following requirements. The sensor/transmitter shall transmit an instantaneous measured data, if a pressure change of 2.0 psi from the last transmission or greater has occurred with respect to the following conditions. If the pressure change was a decrease of pressure, the sensor/transmitter shall transmit immediately every time it detects the 2.0-psi or greater pressure changes from the last transmission. If the pressure change of 2.0 psi or greater was an increase of pressure, the silent period between the RPC transmission and the last transmission shall be 30.0 seconds, and the silent period between the RPC transmission and the next transmission (Normal scheduled transmission or another RPC transmission) shall also be 30.0 seconds, to be in compliance of FCC Part 15.231. Factory Mode The factory mode is the mode that the sensor shall transmit more often in the factory to assure the programmability of the sensor ID during the manufacturing process. Off Mode This Off Mode is only for production parts sensors that are used for the builds during the production process and not in the service environment. LF Initiation The sensor/transmitter must provide data upon the presence of an LF signal. The sensor must react (Transmit and provide data) no later than 150.0 ms after the LF data code has been detected at the sensor. The sensor/transmitter must be sensitive (As sensitivity is defined in Table 1) and able to detect the LF field. The device under test is manufactured by the grantee (Schrader Electronics) and sold as an OEM product. Per 47 CFR 2.909, 2.927, 2.931, 2.1033, 15.15(b) etc, the grantee must ensure the end-user has all applicable / appropriate operating instructions. When end-user instructions are required, as in the case of this product, the grantee must notify the OEM to notify the end-

user. Schrader Electronics will supply this document to the reseller/distributor dictating what must be included in the end users manual for the commercial product. INFORMATION TO BE INCLUDED IN THE END USER'S MANUAL The following information (in blue) must be included in the end product users manual to ensure continued FCC and Industry Canada regulatory compliance. The ID numbers must be included in the manual if the device label is not readily accessible to the end user. The compliance paragraphs below must be included in the user's manual.

FCC ID:MRXAFFPK4 IC: 2546A- AFFPK4 This device complies with Part 15 of the FCC Rules and with Licence exempt RSS standards of Industry Canada. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressely approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE:This equipment has been tested and found to comply with the limits for a class B digital device ,pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmfull interference in a residential installation..This equipment generates ,uses and radiates radio frequency energy and,if not installed and used in accordance with the instructions ,may cause harmfull interference to Radio communications. However there is no guarantee that interference will not occur in a particilar installation. If this equipment does cause harmfull interference to radio or television reception ,which can be determined by turning the equipment off and on ,the user is encouraged to try to correct the interference by one or more of the following measures.

-Reonent or relocate the receiving antenna

-Increase separation between equipment and receiver .

-Connect the equipment into an outlet on a circuit different from that to which the reciver is connected..

-Consult the dealer or an experienced radio/TV technician for help. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. WARNING: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term IC: before the radio certification number only signifies that Industry Canada technical specifications were met.

1 2 3 4 5 REV 01 02 6 REVISION DESCRIPTION INITIAL RELEASE 7 BY D.Z ZZ ECO 8 DATE ECO-396230 14/Oct/2020 ECO-470441 02/Dec/2021 INCREASE THE EXPORT CERTIFICATION OF THE UNITED STATES AND CANADA. A B D E F 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 MECH CODE 01511 PRODUCTION LOCATION COUNTRY OF MANUFACTURE ANTRIM CHANGZHOU UK CHINA TABLE 1 TABLE 2 C PRODUCT MARKINGS TABLE 3 LABEL No. DESCRIPTION TEXT/ LOGO

[TEXT FONT: DIN1451]

SIZE REQUIRED OPERATING FREQUENCY 433 MHz 0.9mm 2D MATRIX

(ENCODED WITH N/A) 4.0mm x 4.0mm 2D DATA MATRIX CUSTOMER PART No. ASIC ID

(IN FORMAT: HEXADECIMAL) PRODUCTION DATE SUPPLIER'S CODE COUNTRY OF MANUFACTURE

(REFER TO COLUMN 2 IN TABLE 2) MODEL No. CMA GB CERTIFICATION NUMBER MATERIAL CODE COMPANY BRANDING VALVE BODY ID 2D DATA MATRIX

(CONTAINING MECHANICAL ID 01511) PRODUCT DIFFERENTIATION MARKING 8891716275 ID: XXXXXXXX YYMMDD 519056 MADE IN XXXXXX M: AFFPK4 HSSI

>PA6-GF35<

0.9mm 0.9mm 0.9mm 0.9mm 0.9mm 0.9mm 1.2mm 0.8mm LEGIBLE 0.9mm 2D MATRIX 10.0mm x 2.5mm 01 02 03 04 14 5 7 2 6 1 7 1 9 8 8 X X X X X X X

D I 433 MHz YYMMDD 519056 MADE IN XXXXX FCC ID: MRXAFFPK4 IC: 2546A-AFFPK4 M: AFFPK4 HSSI 05 06 07 16 02 15 02 08 09 DASHED LINE FOR REFERENCE ONLY DO NOT MARK DASHED LINE 0.50 KEEP OUT Top View Bottom View

>PA6-GF35<

13 11 10 12 Rear View A B C D E F COUNTRY APPROVALS TABLE 4 LABEL No. EUROPE CANADA USA RED IC FCC REGION AUTHORITY SYMBOL REF. CODE/ TEXT

[TEXT FONT: DIN1451]

REQ. ON SENSOR SIZE REQUIRED N/A SYMBOL IC: 2546A-AFFPK4 FCC ID: MRXAFFPK4 TEXT TEXT N/A N/A 2 TEXT N/A 0.9mm 0.9mm 02 02 SYMBOL 3.0mm N/A N/A 4 FOR REFERENCE ONLY, CHECK LATEST REVISION BEFORE USE. REFER TO PLM FOR CONTROLLED DATA, CHANGE HISTORY AND APPROVALS. TECHNOLOGY PARK, ANTRIM, UK, BT41 1QS MATERIAL N/A MASS (g) N/A PROJECT NO. PRJ0012367 REVISION SYMBOL THIS DRAWING IS CONFIDENTIAL AND PROPRIETARY OF SCHRADER ELECTRONICS LIMITED. THE INFORMATION CONTAINED WITHIN IT MAY NOT BE USED, DISCLOSED OR REPRODUCED IN WHOLE OR PART, WITHOUT THE EXPRESSED WRITTEN CONSENT OF SCHRADER ELECTRONICS LIMITED. NO RIGHT IS GRANTED TO DISCLOSE OR USE ANY INFORMATION CONTAINED WITHIN THIS DRAWING. SCHRADER ELECTRONICS LIMITED IS PART OF THE SENSATA TECHNOLOGIES GROUP. TITLE INTERPRET DRAWING PER ASME Y14.5-2009 SEE NOTES FOR GENERAL TOLERANCE UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS DO NOT SCALE DRAWING THIRD ANGLE PROJECTION PART NUMBER 70503112355 GEELY CMA GEN6 PAL FARADAY HG TX 433 LASER MARKING DRAWING SIZE DRAWING NO. DRAWING REV. A3 00013872 02 SCALE 2:1 SOLIDWORKS 2020 SHEET 1 OF 1 ENG-F-044 ISS 05 1 3 5 6 7 8

C5266091_X10_Ed.2 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date:

18.11.2021 Subject: Request for Confidentiality FCC ID: MRXAFFPK4 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No No No NOTE 1 NOTE 1 No No Short-Term Confidentiality NOTE 2 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential 1/1 C5266091_X10_Ed.2 documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely,James Kyle Signature:

Name: James Kyle Title:RF Approval Co-ordinator. 1/1

C5266091_X8_Ed.1 Letter of Authorization Company: Schrader Electronics Ltd Address: Unit 11 Technology Park Antrim, Co Antrim N. Ireland, UK BT41 1QS Product Name: TYRE PRESSURE SENSOR Model Number:AFFPK4 FCC Identifier:MRXAFFPK4 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name:

Title:

RF Approval Co-ordinator Date: 18.11.2021 James Kyle 1/1 C5266091_X8_Ed.1 Signature of applicant:

1/1