FCC ID: MRXAHMPD4 Tyre Pressure Monitor

Schrader Electronics Ltd Unit 11 Technology Park Belfast Road Antrim, Northern Ireland, BT41 1QS TPMS (Tire Pressure Monitoring Sensor) Model: AHMPD4 User Manual Schrader Sensor Overview The Schrader Electronics TPMS (Tire Pressure Monitoring) Sensor is designed to be used in a direct measurement TPM System. The TPM Sensor is intended to interface to a receiver/decoder that has been designed to accept the TPM sensor protocol. The TPM Sensor is designed to monitor a vehicle's tyre pressure whilst driving or stationary. An electronic unit inside each tyre (referred to as the TPM Sensor or TPM transmitter) mounted to the valve stem, periodically measures actual tyre pressure/temperature. This pressure information is transmitted to a receiver/decoder by means of an RF link. The incoming radio frequency signals are decoded, and the data used to inform the driver of the tyre pressure information via the vehicles TPM interface. TPM Sensor main functions are:

Regularly measure the tyre pressure. Monitor if the wheel is moving. Periodically transmit tyre pressure using an RF link and a specific protocol. Notify the system if there are abnormal pressure variations (leak) in the tyre. Monitor the transponder input for valid LF field http://www.tpmseuroshop.com/documents/declaration_conformities

Schrader Electronics Ltd Unit 11 Technology Park Belfast Road Antrim, Northern Ireland, BT41 1QS User Manual Statement FCC ID: MRXAHMPD4 IC: 2546A-AHMPD4 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. http://www.tpmseuroshop.com/documents/declaration_conformities

1 2 3 4 1 GRID REF 1A 5 REV 01 6 7 REVISION DESCRIPTION INITIAL RELEASE BY JJ ECO ECO-XXXX 8 DATE XXXX A B C D E F 2 1 433 MHz YYMMDD MADE IN XXXXX M:AHMPD4 13533166

>PA66-GF13<

XXXXXXXX 5 6 4 7 3 8 FCC ID:MRXAHMPD4 IC:2546A-AHMPD4 IFT:XXXXXXX-XXXXX R-C-SRD-AHMPD4 4S 9 10 11 12 13 17 16 15 14 18 Table 5 MECH CODE XXXXX D R A F T - F O R T E C H N I C A L F E E D B A C K O R Q U O T A T I O N P U R P O S E S O N L Y S U P P L I E R S - P L E A S E N O T E W H E N I N C O M M U N I C A T I O N W I T H S E N S A T A A B O U T D R A F T I T E M S , P L E A S E U S E P A R T N U M B E R T O G E T H E R W I T H 3 D C A D V E R S I O N A S U N I Q U E I D E N T I F I E R O F R E F E R E N C E D 3 D C A D M O D E L D R A W I N G V E R S I O N 3 D C A D V E R S I O N X X P A R T N O ITEM DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PRODUCTION DATE FREQUENCY COUNTRY OF MANUFACTURE MODEL NUMBER CUSTOMER PART NUMBER MATERIAL CODE ASIC ID FINAL TEST DATA MATRIX EU APPROVAL PRODUCT DIFFERENTIATION MARKING SCHRADER ELECTRONICS LOGO SOUTH KOREA APPROVAL LOGO RUSSIA APPROVAL LOGO SOUTH KOREA APPROVAL MEXICO APPROVAL CANADA APPROVAL USA APPROVAL VALVE BODY ID MATRIX SIZE REQUIRED LEGIBLE LEGIBLE LEGIBLE LEGIBLE LEGIBLE LEGIBLE LEGIBLE 4mm x 4mm 5mm x 5mm 5mm x 5mm Table 1 IDENTIFICATION YYMMDD 433 MHz MADE IN MEXICO M:AHMPD4 13533166

>PA66-GF13<

XXXXXXXXX 2D MATRIX CE MARK 4S SCHRADER ELECTRONICS LOGO LEGIBLE KCC LOGO EAC LOGO R-C-SRD-AHMPD4 IFT:XXXXXXX-XXXXX IC:2546A-AHMPD4 FCC ID:MRXAHMPD4 2D MATRIX 5mm x 5mm 5mm x 5mm LEGIBLE LEGIBLE LEGIBLE LEGIBLE LEGIBLE Table 2 Table 3 FONT TYPE TEXT HEIGHT ASIC CODE FORMAT HEXADECIMAL DIN 1451 0.65mm PRODUCTION LOCATION COUNTRY OF MANUFACTURE AGUASCALIENTES MEXICO Table 4 SCHRADER PART NO. CUSTOMER PART NUMBER 70503106675 13533166 FINAL TEXT MATRIX READOUT abc FOR REFERENCE ONLY, CHECK LATEST REVISION BEFORE USE. TECHNOLOGY PARK, ANTRIM, UK, REFER TO PLM FOR CONTROLLED DATA, CHANGE HISTORY AND APPROVALS BT41 1QS MATERIAL N/A MASS (g) N/A PROJECT NO. PRJ0007412 REVISION SYMBOL XX THIS DRAWING IS CONFIDENTIAL AND PROPRIETARY OF SCHRADER ELECTRONICS LIMITED. THE INFORMATION CONTAINED WITHIN IT MAY NOT BE USED, DISCLOSED OR REPRODUCED IN WHOLE OR PART, WITHOUT THE EXPRESSED WRITTEN CONSENT OF SCHRADER ELECTRONICS LIMITED. NO RIGHT IS GRANTED TO DISCLOSE OR USE ANY INFORMATION CONTAINED WITHIN THIS DRAWING. SCHRADER ELECTRONICS LIMITED IS PART OF THE SENSATA TECHNOLOGIES GROUP. INTERPRET DRAWING PER ASME Y14.5-2009 SEE NOTES FOR GENERAL TOLERANCES UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETRES DO NOT SCALE DRAWING THIRD ANGLE PROJECTION PART NUMBER TITLE 70503106675 GM GEN6 GB EDISON II SAL TFA MINI LSSI TX 433 LASER MARKING DRAWING SIZE DRAWING NO. DRAWING REV. A3 00011995 01 SCALE 2:1 CATIA V5R28 SHEET 1 OF 1 A B C D E F ENG-F-044 ISS 04 1 2 3 4 5 6 7 8

SCHRADERELECTRONICS Authority to Act as Agent and REL Listin We appoint Michael Kirby on behalf of Compliance Engineering Ireland to act as our agent in the preparation of this application for equipment certification. We certify that submitted documents properly describe the device or system for which equipment certification is sought. We also certify that each unit manufactured, imported or marketed, as defined in Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. Further, in accordance with section 6.5 of IC CB-02, we hereby acknowledge that our companys product cannot be distributed, leased or offered for sale in Canada until its listed on the Industry Canada Radio Equipment List (REL). For instances where our authorized agent signs the application for certification on our behalf, we acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by American Certification Body, Inc still resides with Schrader Electronics Unit 11 , Technology Park Antrim ,Co Antrim N.lreland,UK BT41 1QS For TCB applications, we certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) regarding certified equlpment. Agency Agreement Expiration Date: (optional) Dated this 30 dayof__JAv_ 20 28 By: : Shes ihe

(Signature) (Print name) Ze ANMuevitt CO -0RyndTOoR Y Ca SATA , Co email:

On behalf of: GtSKIA ExteTiottesS. KD

(Company Name) Telephone: O26 Fle 2067

SCHRADER ELECTRONICS Request for Confidentiali Date: January 31, 2020 Subject: Confidentiality Request for: (FCC ID: MRXAHMPD4 IC ID:2546A-AHMPD4) Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 9.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent *? Internal Photos Short Term x] Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent *? Users Manual Schrader Electronics Ltd has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___ (specify number of days not to exceed 180)__ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By: (lALtdeD? file Saves [CML

(Print name)

?~ The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for DOI found at:

https://apps. fec.gov/oetef/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=4 1731 and review section II, 3) regarding specific information that must accompany these requests. 3 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details.

+ - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 053019 12