m m 5 9 MIDI SDF Cellular Platform Compact Mobile Base Station Systems The SDF MIDI Platform is a two Carrier Mobile Base Station solution give ability to work on 2G to 4G cellular Network. The MIDI platform is based on Intel i7 support embedded Linux operating system and provide base station solution and GNSS functionalities to meet application demands. 340mm 351mm Tx1 Tx2 M O D E M PWR SYS SERIAL Display Port CHR ON/OFF SIM CARD DONT REMOVE!
T GPS ETH USB3 14-22 VDC Tx1 BP Tx2 BP GPS Wi-Fi Rx1 Rx2 190mm Application UE UE UE eNB UE ngeNB UE 2Gto5G Network MIDI S D AXI 520 0 1 2 3 4 5 6 7 ALAR M ROUTING ENGINE AXI 520 BTS S D AXI 520 0 1 2 3 4 5 6 7 ALAR M ROUTING ENGINE AXI 520 NodeB UE UE ExternalPAoption D S WiFi Network Cellular Network IP Network Septier NMS Highlights The MIDI platform features up to 2xSDR carrier, providing extremely high performance cellular applications. The unique thermal solution supports efficient front-to-back cooling solution Includes Internal charger and Li-Ion battery Includes Internal dual RF Power Amplifier, up to 5Watt output per port (Lte signal) Small size or 19-inch rack-mount enclosure Efficient front-to-back cooling Up to 2 independent SDR ( software defined Radio) Support External RF Power Amplifier (bypass option) Support Wi-Fi, Ethernet or Lte network for Remote control Network management using SDF GUI software Support GNSS (GPS, GLONASS, Galileo, QZSS) Support GSM 850/900/1800/1900 Support WCDMA B1/B2/B4/B5/B8 Support LTE-FDD Bands:B1/B2/B3/B4/B5/B7/B8/B12/B13/B14/B20/B22/B28/B71 Support LTE-TDD Bands:B38/B40/B41/B42/B66 Dimension: 340x190x95mm (L*W*H) System Interfaces The platform provides the following interfaces and peripheral connectivity Internal 3S Li-Ion battery (130Wh) UIM interface RF separated TX/RX interface. Additionally internal Power Amplifier bypass output option On/Off power control USB3.0 Interface UART serial port over USB2.0 Interface GNSS external RF Antenna Wi-Fi external RF Antenna Remote control modem external RF Antenna Ethernet 1000/100/10 Interface Display port Interface External power supply System status LEDs Power Supply Specification 360W continues power supply AC input: 85 to 264V, 47 to 63Hz Output: 15Vdc Protections : Short circuit/Overload/Over voltage/Over temperature Fully Enclosed plastic case Built-in active PFC function Fanless designed with -30 to +70C working temperature Dimension: 220x95x46mm (L*W*H) Environmental specifications Temperature operating -5C to +50C Non-operating temperature -25C to 80C Humidity Operating 20% to 80% non-condensing FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.