iBT52 IB (Eng) US ver. Size: 300mm x 260mm Printing color: 1C +1C (Black) Apr 16, 2013
(Front) iBT52 Portable USB Bluetooth Receiver Introduction Thank you for purchasing the iHome iBT52. This product is designed to provide high quality wireless sound and speakerphone capability to audio devices equipped with line-in jacks, and to headphones. Along with the included Quick Bluetooth Connection Guide this instruction booklet explains the basic operation and care of the unit. Please read them carefully and keep for future reference. Maintenance Keep unit away from sources of excessive heat. Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as thinner or similar materials can damage the surface of the unit. Included iBT52 Bluetooth receiver system
(Bluetooth Receiver + docking station with USB + audio cable) iBT52 Home Docking Station (with attached Aux + Micro USB cable) USB Wall Adaptor FCC Information FCC ID: EMOIBT52 FCC Radiation Exposure Statement IC: 986B-IBT52 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This Device complies with RSS-102 of the IC Rules; Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may cause undesired operation. This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Connect the equipment into an outlet on a circuit different from that to which the Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. receiver is connected. Instruction manual Information FCC FCC ID: EMOIBT52 FDclaration de la FCC sur lexposition aux radiations IC: 986B-IBT52 Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Le dispositif rencontre l'exemption des limites courantes d'valuation dans la section 2.5 de RSS 102 et la conformit l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformit de rf. Cet appareil rpond aux exigences du paragraphe 15 de la loi de la Commission Fdrale sur les Communications. Lutilisation de cet appareil doit rpondre aux deux conditions suivantes: (1) Cet appareil ne doit pas provoquer dinterfrences nuisibles, et (2) cet appareil doit accepter toutes les interfrences reues, y compris les interfrences pouvant provoquer un fonctionnement non dsir. Avertissement : Tout changement ou modification apport cet appareil sans le consentement expresse de la partie responsable pour la conformit peut annuler le droit de l'utilisateur d'utiliser cet appareil. Remarque : Cet quipement a t test et jug conforme aux limitations pour un appareil numrique de Classe B, selon la Section 15 de la rglementation FCC. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nuisibles dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre des frquences radio et, s'il n'est pas install et utilis selon les instructions, peut causer des interfrences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des interfrences ne se produiront pas dans une installation particulire. Si cet quipement produit des interfrences nuisibles sur la rception de la radio ou de la tlvision, ce que vous pouvez facilement constater en teignant et en rallumant l'quipement, nous vous encourageons prendre l'une ou plusieurs des mesures correctives suivantes :
Rorienter ou dplacer lantenne rceptrice, loigner davantage l'appareil du rcepteur. Branchez lquipement sur une prise ou un circuit auquel le rcepteur nest pas branch. Consultez votre revendeur ou un technicien radio/tlvision qualifi pour plus dinformations. ppareils digitaux de Classe B compatible avec lICES-003 Canadien. Meet Your iBT52 iBT52 Home Docking Station Side Front Micro USB Plug Audio Plug iBT52 Bluetooth Receiver Top Micro USB Charging Port Aux-out Jack Side Front Sport Clip Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada Using the USB Wall Adaptor 1. Gently connect the Bluetooth Receiver to the Docking Stations micro USB plug and audio plug by sliding the Receiver onto the plugs. 2. Connect the standard USB plug of the Docking Station into the USB Wall Adaptor. 3. Plug the USB Wall Adaptor into a working wall outlet. For first time use, charge unit for about 3 hours. Using other USB Power Source 1. Gently connect the Bluetooth Receiver to the Docking Stations micro USB plug and audio plug by sliding the Receiver onto the plugs. 2. Connect the standard USB plug of the Docking Station into a power USB port on a computer or other USB charging device. For first time use, charge unit for about 3 hours. The iH Button/ Indicator Light on the front of the Bluetooth Receiver glows red steadily while the unit is charging and turns OFF once the unit is fully charged. If unit is not powered on is connected to USB power, the red light glows steadily to indicate unit is charging. Using the USB Wall Adaptor Using the USB Power Source USB 2.0 Backlit Pairing/Operation Button with Indicator Light NOTE: When the unit is on and not connected to a power source, the iH Button/
Indicator Light flashing red means the battery needs charging. iBT52 IB (Eng) US ver. Size: 300mm x 260mm Printing color: 1C +1C (Black) Apr 16, 2013
(Front) Using Bluetooth: Pairing Your Device 1. Turn on your Bluetooth-enabled device and turn on Bluetooth capability as described in the devices user manual. 2. Move the Power On/Off Switch on the Bluetooth Receiver to the ON position
(right). The unit will turn on and attempt to auto link to the last 2 previously paired devices for 10 seconds each, indicated by a 3 note tone and the iH Button/ Indicator Light on the front of the Receiver flashing blue. If a linked device is found, the indicator will flash blue twice every 7 seconds. 3. If no linked device is found, the unit will enter pairing mode, indicated by the iH Button/ Indicator Light on the front of the Receiver flashing blue and red while the unit attempts to pair. NOTE: If the unit is charging while pairing is attempted, the light will continue to blink blue and red. iHome iBT52 should appear on your devices menu. If Not Paired, Not Connected or similar appears on your display, select iHome iBT52 to complete pairing. If your device asks for a password, enter 0000 on the keyboard of your device. If no device is paired within 2 minutes, a tone will sound and the unit will revert to auto link mode. To retry pairing, move the Power On/Off Switch to the OFF position (left) then move it back to the Bluetooth position (center). 4. Once paired with a device, the iH Button/ Indicator Light on the front of the Receiver will flash blue twice every 7 seconds. There should be an indication on your device that pairing is complete. On some devices, you must then select Use as Audio Device or similar on the devices Bluetooth menu. Once paired, your device should link to the iBT52 whenever within range. Pairing with a Different Device 1. When you power ON the Receiver, it will automatically link with the last previously paired Bluetooth device as long as that device is still within range
(about 30 feet). So, to pair with a different device you must turn off the Bluetooth capability of the already paired device. Connecting Audio Source to Bluetooth Receiver 1. Connect the audio cable on the Docking Station to your desired speaker or audio devices line in jack. For portable use, connect headphones or an audio cable connected to a speaker or audio device to the Aux-out Jack on the Bluetooth Receiver (receiver must be charged). 2. Move the Power On/Off Switch to the ON position (right) to listen to audio streamed wirelessly from your paired iPad, iPhone, iPod or other Bluetooth device. The iH Button/ Indicator Light on the Receiver will flash blue as the unit searches for a previously paired device, and then flash blue twice every 7 seconds once a previously paired device is detected. 3. Press the iH Button to play or pause tracks. Use the controls on your device to navigate tracks and control volume from your Bluetooth device. 4. When done listening, move the Power On/Off Switch to the OFF position (left) to turn the unit off. Connecting Receiver to Speaker Using Aux Out While the Bluetooth Receiver is docked in the Docking Station, you can connect the Docking Station to any external speaker or audio device with a speaker and aux/line-in jack via the Aux-out cable attached to the Docking Station. You can also connect the Bluetooth Receiver directly by connecting a standard 3.5mm stereo audio cable to the Aux-out jack on the Bluetooth Receiver and the other end into the desired Line-in jack. 1. Connect a 3.5 mm audio cable plug to the Aux-out jack on back of the unit and connect the other end to the line-in jack on your external speaker. Note that the aux output signal is stereo. 2. Move the Power On/Off Switch to the ON position (right) to listen to audio via the selected mode. 3. Power on the audio device and use the controls on the device to navigate tracks and control volume. Press the iH Button to play or pause tracks. 4. When done listening, move the Power On/Off Switch to the OFF position (left) to turn the unit off. Remember to turn off your audio device, too. Aux-in DC 12V 2.5A usb charging Using with a Paired Phone Pair your Bluetooth-capable phone as described under Pairing. While the Bluetooth Receiver is connected to an audio device such as a speaker or earphones, you can use the device as speakerphone. Answering Calls Press and release the iH Button to answer a call. The LED flashes blue quickly while the phone is ringing and turns solid blue during the call. Ending Calls Press and release the iH Button to end a call. The LED returns to standard mode (flashes twice every 7 seconds). Rejecting Calls Press and hold the iH Button for 1 second to reject a call. The LED flashes blue quickly while the phone is ringing then returns to standard mode (flashes twice every 7 seconds). Voice Dialling Press and hold the iH Button for 3 seconds, then say the voice tag at the beep Make sure to record voice tag into phone before attempting voice dial function. Only available on paired phones that have voice dial capability (see your phones user guide). Redial Press and release the iH Button twice to redial the last number called. Call Waiting Press and release the iH Button to place a current call on hold and answer a new call. Press and hold the iH Button for 1 second to ignore a new call and stay with the current call. Press and release the iH Button twice to hang up on a current call and answer a new call. Troubleshooting Unit doesnt respond (no power) Make sure unit is completely charged. Check that all connections are correct and properly plugged in. Make sure your device is properly paired with the iBT52. Make sure the Power On/Off Switch switch is not in the OFF (left) position. Resetting the iBT52 If the unit becomes locked up or unresponsive, you may need to reset it. To do so, press and hold the iH Button for 6 seconds then rapidly press and release it twice (2x) . 2 long beeps indicate unit has been reset. Trouble pairing device/computer with iBT52 Bluetooth implementation varies depending on your devices hardware and operating system. Please see our website for updates on pairing. When you power ON the Receiver, it will automatically link with the last previously paired Bluetooth device if the device is still within range (about 30 feet). To pair with a different device you must turn off Bluetooth capability on the already paired device, or take it out of range. If your device does not auto-link when within range, re-pair the device. To do so, first delete the iBT52 from your Bluetooth devices menu. Move the Power On/Off Switch on the unit to the OFF position then back to ON to begin pairing (see Pairing Your Device for pairing details). Make sure your device is working properly. Check your devices manual for details on Bluetooth pairing and linking. For further information and to see the latest instructions, visit www.ihomeaudio.com/support Internal Rechargeable Lithium-ion Battery This device uses an internal rechargeable lithium-ion battery that should last the lifetime of the device. If you suspect your battery may be dead, try charging it several times. If the battery does not recharge, please contact us for repair information. WARNING/DISPOSAL OF UNIT Please do NOT attempt to change the battery yourself. If the battery has died and you do not want us to replace your battery, you should follow the disposal instructions below:
Never dispose of used batteries/electronics with ordinary solid wastes, since they contain toxic substances. Always dispose of used batteries/electronics in accordance with the prevailing community regulations that apply to the disposal of batteries/electronics. If there are no local regulations concerning battery/electronics disposal, please dispose of the device in a waste bin for electronic devices. Many electronics retailers now recycle batteries and other electronic components at no charge. Check to see which ones in your area do so. CAUTION The battery used in this device may present a risk of fire, explosion or chemical burn if mistreated Never use or charge the battery if it appears to be leaking, discolored, deformed, or in any way abnormal. Never disassemble the unit or attempt to remove battery as that could cause leakage of alkaline solution or other electrolytic substance. Always confirm that the temperature is 5C 35 C (41 - 95 Fahrenheit) before you charge the battery. Leakage or deterioration of the battery may occur if this warning is not heeded. Never expose the battery to any liquid. Never expose the battery to excessive heat such as direct sunlight or fire. Never use the battery pack in an unventilated vehicle where excessive internal temperatures may be encountered. Always keep the battery out of the reach of infants and small children. Consumer Product Safety Guide IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1. Water and Moisture The unit should not be used near water. For example:
near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. 2. Ventilation The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through the ventilation openings. 3. Heat The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat. 4. Power Sources The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 5. Power-Cable Protection Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where it is plugged into an AC socket. 6. Cleaning The unit should be cleaned only using a warm damp cloth. Do not use solvents, etc. 7. Objects and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on the product. 2013 SDI Technologies, Inc. All rights reserved Questions? Visit www.ihomeintl.com iBT52-041613-EN Printed in China