iZBT50 - QSG (English) Size: 510 x 150 mm (folded 102 x 150 mm) Material: 157g Art paper Color: 1C + 1C (black) July 21, 2022 SWEETDREAMS SOOTHER WITH CRY SENSOR Model: iZBT50 QUESTIONS? visit www.ihome.com OVERVIEW On|Off Press to turn Off/On current Light and Sound mode, reset Cry-Activated Soother, or reset a Schedule Mode Change Light Mode Press to cycle through 6 different light modes battery backup unscrew to open REMOTE CONTROL Preset Button Press to turn on/off a saved Light and Sound Mode Press and hold to save current settings as a new preset Change Brightness Press to adjust the brightness of your products light modes. preset mode Change Sound Mode schedule sound light play|pause on|off on|off on|off Press to cycle through 15 different sounds Activate Schedule Press to turn on/off On|Off Press to turn Off/On current Light and Sound mode, reset Cry-Activated Soother, or reset a Schedule Mode To toggle Time Sync ON or OFF, press and hold the Time Set Button for 10 seconds. BOTTOM CONTROLS (FOR ADVANCED FEATURES) GETTING STARTED Preset Bar Tap to turn on/off a saved Light and Sound Mode Tap and hold to save current settings as a new preset Change Sound Mode Press to cycle through 14 different sounds Set a Schedule Press to preview Press again to activate Press and hold to customise Child Lock Press and hold both 1+2 to lock all controls*
*except power Change Brightness Press to adjust the brightness of your products light modes. When youre setting a schedule, or adjusting the time, use these buttons for that too!
Volume Control Press to adjust the loudness of your product DISPLAY Change Light Mode Press to cycle through 6 different light modes Bluetooth Pair Press and hold to pair your phone Press to Play/Pause your music Cry-Activated Soother Press to turn on/off at the last used sensitivity Note: If you leave the cry sensor ON outside of sleep/nap times, day noise can activate the feature. Turn ON/OFF via remote control before and after sleep routines. 1 PM AM Low Battery Cry Sensor (Soothe) When your baby cries, this unit will play a soothing Shush Try 3 different levels of sensitivity!
Soother will not activate Level 1:
(High Sensitivity) Soother activates when there is very little noise Level 2:
Soother activates when there is a moderate amount noise Level 3:
(Lowest Sensitivity) Soother activates ONLY with there is loud crying or noise Bluetooth Pair Press and hold to pair your phone Press to Play/Pause your music NOTE: Use Bluetooth to automatically sync time with your phone!
Volume Control Press to adjust the loudness of your product 1. Connecting the Unit Connect the included AC adapter to the DC jack located on the back of the unit and connect the other end to a working wall outlet not controlled by a light switch. Remove the battery pull tab from the back of the unit. DC Jack 2. Connecting to Bluetooth Turn on your Bluetooth device and make it discoverable by turning on Bluetooth mode. Press and hold the Bluetooth Pairing Button on the bottom of the iZBT50 unit, or on the remote control, until the Blueooth Pairing Icon flashes to indicate the unit is in pairing mode. iHome iZBT50
Conrm / Time Set Press and hold to adjust clock time When youre setting a schedule, or adjusting the time, use this button to conrm current setting Select iZBT50 on your devices Bluetooth menu to connect!
iHome 3. Setting Your Clock LIGHT THERAPY Press the Light Button repeatedly to cycle through light therapy modes:
RESET RESET TEST TEST Rest Glow One Color Sun Light Candle Off
- Red Light mode for falling asleep
- Rainbox spectrum slow fade
- Pick your favorite color
- Adjustable lamp for reading or sleep
- Warm calming mood lighting effect ADJUST BRIGHTNESS NOTE: Press & Hold to Turn OFF current Light Therapy Mode SOUND THERAPY Press the Sound Button repeatedly to cycle through sound therapy modes:
Sleep Air Focus Quiet Drive Shush Meditation Lullaby Brahms Silent Night Twinkle Morning Light Nature Ocean Storm Nature River OFF Cry Sensor Activation Mode Auto Time Sync (via Bluetooth) NOTE: Press & Hold to Turn OFF current Sound Therapy Mode Automatically sync the clock time of the unit to your iPhone or iOS device over Bluetooth. The time will sync when you first pair and re-link your device over time. NOTE: Does not work with Android devices Manually Setting the Time Child Lock Active 1. Press and hold the Time Set Button on the bottom of the unit until the display flashes and a beep sound. Release the Time Set Button. 2. Press the or + Buttons to select 12 or 24 hour display mode and press Sound Therapy Time Set to confirm. 3. Press the or + Buttons to adjust the hour, and tap Time Set to confirm. (Make sure to set correct AM/PM time). The AM/PM indicators appear on the left side of the display. 4. Press the or + Buttons to adjust the minute, and tap Time Set to CRY-SENSOR (SOOTHE MODE) Activate the Cry-Sensor Mode to sense when your baby is crying and automatically play a soothing Shushing voice to calm your baby and help training for improved sleep (both parents & baby). Try 3 different levels of sensitivity!
Level 1:
(High Sensitivity) Level 2:
Level 3:
(Lowest Sensitivity) Soother will not activate Soother activates when there is very little noise Soother activates when there is a moderate amount noise Soother activates ONLY with there is loud crying or noise CRY-SENSOR ON Time Set confirm. 2 NOTE: Cry Activation mode cannot be armed while in Bluetooth mode. If Sounds Therapy is ON, the maximum volume will be limited to aid in sensing when your baby is crying. 4 3 Schedule 1 Schedule 2 Bluetooth connected Light Therapy HOW TO SAVE A PRESET The unit allows you to store a preset to easily access your favorite light, sound, and sleep mode combinations using the remote control. 1. When your preferred light, sound, and sleep modes are active, press and hold the Preset Button to save a preset. 2. Once set, press the Preset Button or tap the preset bar to activate your preset at any time. 3. Tap the preset bar to turn off your preset at any time. SETTING SCHEDULE 1 & 2 Customize up to two programs of light/sound with a start and end time. 1. Press and hold the OR for 2 seconds to begin. The hour digit will flash. SET THE START TIME 2. Press the OR to set the start hour to the desired time. The AM/PM indicator appears to the left of the display. Press to confirm. 3. Press the OR Buttons to adjust the minute of the start minute to the desired time. Press to confirm. SET THE END TIME 4. Press the OR Buttons to schedule the end hour to the desired time. Press to confirm. 5. Press the OR Buttons to schedule the end minute to the desired time. Press to confirm. SET THE SOUND MODE 6. Press the OR Buttons to select a preferred sound (1-15 tones). Press to confirm. 7. Press the OR Buttons to adjust the volume (1-16). Press to confirm. SET THE LIGHT MODE 8. Press the OR Buttons to select 1 of 5 different light modes. Press to confirm. 9. Press the OR Buttons to select brightness level (1-20) Press to confirm. DONE!
10. When set, Schedule 1/2 will display the respective / icons on the display and will activate between the respective Start/End times. 11. Press or / to suspend active schedule and reset for next day. 5 USING THE CHILD LOCK When the child-lock feature is active, only Power ON/OFF will function on the unit. Press and hold both the Schedule 1 and Schedule 2 Buttons at the same time for 2 seconds. NOTE: The lock icon will appear on the display to conrm the unit is locked. REMOTE CONTROL BATTERY The remote control is powered by a CR2032 button cell battery. To replace the battery:
1. 2. 3. Use a Phillips screwdriver to open the battery compartment door located on the back of the remote control. Insert a fresh CR-2032 battery, checking that the polarity matches the markings on the battery slot. Replace the compartment door. Do not overtighten the screw. USING REMOTE CONTROL This is an RF remote control that allows for simple control of the unit through walls or any direction without getting up or waking your baby (CR2032 battery included). NOT WORKING? If the remote is not working, first try to replace the included battery. If it still isn't working, it likely needs to be re-paired to the unit (each remote is paired to your unit). MANUALLY PAIRING THE REMOTE:
In standby mode, press and hold both the + and volume +
bottom buttons on unit for 6 seconds, the LCD will show PAIr. Press any remote control button within 1 minute as a pairing signal. After pairing successful, your remote control should be able to operate the unit. BATTERY BACK-UP The unit uses a CR-2450 back-up battery to provide continuous alarm operation and clock settings in the event of a temporary power failure. Remove the battery pull tab before use. When the low battery icon flashes on the clock display, it is time to replace the back-up battery. The battery compartment is located on the back of the unit. 1. Make sure the AC adapter is connected, or you will lose your time and alarm settings during battery replacement. 2. Use a Phillips screwdriver to open the battery compartment door. 3. Insert a fresh CR-2450 battery, checking that the polarity match the unit. the markings on Replace the compartment door. Do not overtighten. WARNING Do not ingest the battery, Chemical Burn Hazard. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY INCORRECT TYPE. DISPOSE OF USED BATTERIES AN ACCORDING TO THE INSTRUCTIONS. IMPORTANT SAFETY INSTRUCTIONS Please heed all warnings, read and follow all instructions and keep these instructions handy for future reference. 1. Do not use this product near water. 2. Unplug unit and clean only with damp cloth. Stronger cleaning agents, such as Benzene, thinner or similar materials can damage the surface of the unit. 3. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 4. Heat This product should be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat. 5. Only use attachments/accessories specified by the manufacturer. 6. Unplug this product during lightning storms or when unused for long periods of time. 7. Damage Requiring Service This product should be serviced by qualified service personnel when:
- Plug has been damaged.
- Objects have fallen into or liquid has been spilled into the enclosure.
- The unit has been exposed to rain. The unit has been dropped or the enclosure damaged.
- The unit exhibits a marked change in performance or does not operate normally. 8. No naked flame sources, such as lighted candles, should be placed on this product. 9. Attention should be drawn to the environmental aspects of battery disposal. Many electronics retailers now recycle batteries and other electronic components at no charge. To find a drop-off location near you, visit www.call2recycle.com 10. This product is suitable for use in tropical and/or moderate climates. 11. Do not place product or remote within reach of baby or children. WARNING:
- To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
- Do not dispose of batteries in the household trash or fire.
- The mains plug of power adaptor is used as the disconnect device, it shall remain readily operable. MAINTENANCE Place the unit on a level surface away from sources of direct sunlight or excessive heat. Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should be placed between it and the furniture. FCC Information This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The main unit (not remote control) should be installed and operated with minimum distance 20cm (8in) between the radiator & your body. ISED Information This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. The device comply with ISED RF exposure requirement, users can obtain Canadian information on RF exposure and compliance. The main unit (not remote control) should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Cet quipement est conforme aux limites d'exposition aux radiations IC CNR-102 tablies pour un environnement non contrl. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) Lappareil ne doit pas produire de brouillage;
(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. L'appareil est conforme aux exigences d'exposition RF ISED, les utilisateurs peuvent obtenir des informations canadiennes sur l'exposition aux RF et la conformit. L'unit principale ( pas de tlcommande) doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. Tout changement ou modification non expressment approuv par la partie responsable de la conformit peut annuler l'autorit de l'utilisateur utiliser l'quipement. CAN ICES-3(B) / NMB-3(B) WARRANTY For product support information and warranty please visit:
www.ihome.com/support 2022 SDI Technologies, Inc. All rights reserved. Questions? Visit www.ihome.com 6 7 8 iZBT50QSG-072122-A Printed in China