Safety Guideline for Using Lithium Battery
(Danish) ADVARSEL! Lithiumbatteri --- Eksplosionsfare ved fejlagtig hndtering. Udskiftning m kun ske med batteri af same fabrikat og type. Lev det brugte batteri tilbage til leverandren.
(Deutsch) VORSICHT: Explosionsgefahr bei unsachgemem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
(English) CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturers instructions.
(Finnish) VAROITUS: Paristo voi rjht, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan valmistajan suosittelemaan tyyppiin. Hvit kytetty paristo valmistajan ohjeiden mukaisesti.
(French) ATTENTION: II y a danger dex;losion sil y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du meme type ou dun type quivalent recommand par le constructeur. Mettre au rebut les batteries usages conformment aux instructions du fabricant.
(Norwegian) ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt same batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres I henhold til fabrikantens instruksjoner.
(Swedish) VARNING: Explosionsfara vid felaktigt batteribyte. Anvnd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvnt batteri enligt fabrikantens instruction. Safety Instructions 1. Read the safety instructions carefully and thoroughly. 2. Save this User Guide for possible use later. 3. Keep this equipment away from humidity and high temperature. 4. Lay this equipment on a stable surface before setting it up. 5. The openings on the enclosure are used for air convection and to prevent the equipment from overheating. Do not cover the openings. 6. Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the equipment to the power inlet. 7. Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord. 8. Always unplug the power cord before inserting any add-on card or module. 9. All cautions and warnings on the equipment should be noted. 10. If any of the following situations arises, get the equipment checked by a service personnel:
The power cord or plug is damaged. Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment has not worked well or you cannot get it work according to Users Manual. The equipment was dropped and damaged. The equipment has obvious signs of breakage. 11. Never pour any liquid into the opening that could damage the equipment or cause an electrical shock. 12. Do not leave the equipment in an unconditioned environment with a storage temperature of 60C
(140F) or above, which may damage the equipment. 13. To prevent explosion caused by improper battery replacement, use the same or equivalent type of battery recommended by the manufacturer only. WEEE Statement Trademarks All trademarks are the properties of their respective owners. Microsoft is a registered trademark of Microsoft Corporation. Windows CE are registered trademarks of Microsoft Corporation. Release History Version 1.0 Revision Note First Release Date 08, 2009 Chapter 1 Introduction of HMT(Home Media Terminal) This mobile wireless device, named Home Media Terminal (hereinafter referred to as HMT), allows to browse web using WLAN and control household digital compliances. This HMT can be used in anywhere at household and connected with other devices via Wireless LAN. For the better performing and safely using HMT, please note it is strongly recommend that HMT should be on the cradle while operating as well as charging battery in HMT. HMT uses up-to-date parts such as 7.0 TFT LCD for wide visibility and touch screen for users convenience. Windows Embedded CE 6.0 is the software that can be operated by the application of Wireless LAN and FM Transmitter. Windows Embedded CE 6.0 in HMT is basic user interface that can be changeable to what end-users working purposes. ( The main functions in HMT are operated properly with different user interfaces) Using the Battery Pack Battery capacity 3000mAh / 3.7V Charging time 4 hour 30min Standard using time Suspend status Video clip play 750 hour 3hour Battery Safety Tips Replacing or handling the battery incorrectly may present a risk of fire or explosion, which could cause serious injury. Only replace the main battery pack with the same or equivalent type of battery. Do not disassemble, short-circuit or incinerate batteries or store them to temperatures above
+60 C (+140 F). Do not temper with batteries. Keep them away from children. Do not use rusty or damaged batteries. Dispose of batteries according to local regulations. Check with your local solid waste officials for details about recycling options or for proper disposal in your area. Conserving Battery Power Efficient battery power is critical to maintain a normal operation. If the battery power is not managed well, the saved data and customized settings may be lost. Follow these tips to help optimize battery life and avoid a sudden power loss. Suspend system operation if the system will be idle for a while or shorten the Suspend Timers time period. Turn off the system if you will not be using it for a long period of time. Disable unneeded settings or remove idle peripherals to conserve power. Connect an AC adapter to the system whenever possible. Charging the Battery Pack The battery pack can be recharged while it is installed in the HMT. Please pay attention to the following tips before recharging the battery:
If a charged battery pack is not available, save your work and close all running programs and shut down the system. Plug in an external AC/DC power source. You can use the system, suspend system operation or shut down and turn off the system without interrupting the charging process. The battery pack uses Lithium-ion battery cells that have no memory effect. There is need to discharge the battery pack before you begin charging. However, to optimize the life of battery, we suggest that consuming the battery power completely once a month is necessary recommended. If you do not use the HMT for a long Period of time, it is suggested to remove the battery pack from your HMT. This may be helpful to extend your battery life. The actual charging time will be determined by the applications in use. How to Use This Manual This Users Manual provides instructions and illustrations on how to operate this Home Media Terminal. It is recommended to read this manual carefully before using this HMT. Chapter 1, General Introductions, includes the descriptions of all the accessories of this HMT. It is recommended that verify you have all the accessories included when you open the packing box. If any item is damaged or missing, please contact the vendor where you purchased this HMT. Chapter 2, Getting Started, provides the specification of this HMT, and introduces the function buttons, connectors, LEDs and external ports of this HMT. Also, this chapter provides the correct procedure for installing or uninstalling the battery pack, and some ideas on how best to use this HMT. Unpacking First, unpack the shipping carton and check all items carefully. If any item contained is damaged or missing, please contact your local dealer immediately. Keep the box and packing materials in case you need to ship the unit in the future. The package should contain the following items:
Home media terminal Docking station. Users guide book. High-capacity Lithium polymer battery pack AC adapter These accessories listed above may change without notice. Chapter 2 Specification Internal power Store Running Size (mm) Weight (g) Temperature Temperature OS DRAM Flash TFT LCD Speaker Audio Out Video mode Video type Frequency Standard Frequency Input Output Property S/W Processor Memory Display Audio AV Input FM Transmitter Wireless LAN Battery Adaptor DC 5V / 3A 193.1(L) x 119.7(W) x 23.5(H) 435g
-10 ~ 60
-40 ~ 85 Windows CE 6.0 Professional S3C6410, 667Mhz 256MB 128MB 7" Wide VGA (800x480) Internal stereo speaker (8/1W * 2ea) Stereo earphone NTSC, PAL CVBS 88.5Mhz ~ 107.9Mhz 802.11b/g 2400Mhz ~ 2483.5Mhz 3.7V, 3000mAh Lithium- polymer rechargeable battery AC 100V~240V, 47Hz~63Hz, 0.5A DC 5V, 3A Product Overview This section provides the description of basic aspects of your HMT. It will help you to know more about the features of this HMT before using it. Note The HMT shown here may vary from the actual one. Front-side View The image of the front -side view(Touch screen LCD) and descriptions below will help you to get familiarized with the main features of your HMT. Bottom -side View Top-side View Right & Left-side View Rear-side View Power Management AC Adapter Please note it is strongly recommended to connect the AC adapter and use the AC power while using this HMT for the first time. When the AC adapter is connected, the battery is being charged immediately. Note That the AC adapter included in the package is approved for your HMT; using other adapters from other manufacturers may damage the HMT or other devices on the HMT. Connecting the AC Power 1. Unpack the package to find the AC adapter and power cord. 2. Attach the power cord to the connector of the AC adapter. 3. Plug the DC end of the adapter to the HMT, and the male end of the power cord to the electrical outlet. Disconnecting the AC Power When you disconnect the AC adapter, you should:
1. Unplug the power cord from the electrical outlet first. 2. Unplug the connector from the HMT. 3. Disconnect the power cord and the connector of AC adapter. 4. When unplugging the power cord, always hold the connector part of the cord. Never pull the cord directly!
Battery Pack This HMT is equipped with a high-capacity Lithium-polymer Battery pack. The rechargeable Lithium-polymer battery pack is the internal power source of the HMT when the AC adapter is not being used. Releasing & Replacing the Battery Pack To remove the battery pack:
1. Make sure the HMT is turned off. 2. Remove the battery cover by pressing down on the cover. 3. Replace the battery cover onto the back of the HMT 4. Take the cable of connects to socket the left side in battery space. 5. While applying pressure, slide the down portion until you hear a light click 5 Warning Do not try to disassemble THE BATTERY PACK. Please follow your local laws and regulations to recycle the unused battery pack. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, avoid direct contact to the transmitting antenna during transmitting. 3. may void the users authority to operate the equipment. RF Exposure Warning This equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. This equipment must not be co-located or operating in conjunction with any other antenna or transmitter. SAR Value: 0.139 W/kg Before You Start ii