FCC ID: VA5ANB300-2WLR Keyless Entry System

2-WAY REMOTE & Antenna STARTING SYSTEM WITH 1 BUTTONS FOR AUTOMATIC TRANSMISSION REH300-2WAY / ANT-2WDSS User Guide For Keyless Entry System The correspond remote with antenna is various WARNING It is the responsibility of the vehicle operator to ensure that their vehicle is par1<ed in a safe and responsible manner. 1. When leaving the vehicle, it is the user's responsibility to ensure that the gearshift lever is in "Park in order to avoid accidents upon remote starting. (Note: Make sure that the automatic vehicle cannot start in onve.) 2. It is the user's responsibility to ensure that the remote starter is disabled or put into valet mode before servicing. FCC COMPLIANCE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference. and

(2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void user's authority to operate this device. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) Lappareil ne doit pas produire de brouillage;

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. F Lock, Unlock and Remote Lock, Unlock and Remote Starting icon is displaying with Starting icon is displaying with One LED color. Two LED color. Using the remote control Description of Remote Appearance Lock/Unlock Note: Press the button 1 time on the remote control transmitter to lock the vehicle. Press the button 2 times to unlock the drivers door, 2 additional times to unlock all doors. 2Way Remote Remote Engine Stop - Press 1Way Remote START/STOP:

Note : Remote Engine Start -

Press the button 1 time and then, within 3 seconds, press and hold the button for 2 seconds the button for 2 seconds Function Lock Unlock drivers door Unlock all doors Remote start/stop Button Functions Button Press buttons for LED Press 1time Press 2 times Press 2times x 2 2 seconds Note: You make sure press button only after LED lighting ends to activate each feature properly. Vehicle Presets Heater When leaving the vehicle it is recommended to preset the accessory controls in preparation for the Next remote start. Settings for the blower motor(fan),front and rear (if equipped),should not be left on HIGH. It is recommended to leave the settings on LOW or MEDIUM instead. Windshield Wipers, Headlights Certain vehicles require the windshield wipers and headlights circuits to become energized while running under remote start. When leaving the vehicle you must ensure that the windshield wipers and headlights switches are OFF. Leaving the headlights switch ON on certain types of vehicles could cause them to remain ON even after remote starter shutdown, resulting in a dead battery. Leave Windshield Wipers off to avoid damage wipers/motor with remote start. Changing the Remote Control Transmitter Battery Remote transmitter should be provided with two 3-volt lithium battery (Model: CR-2025). Please pay attention that with low battery LED in the remote might not work and the remote start distance might get shorter. Batteries can be purchased at any electronic device stores. Following the instructions below to change the remote control battery 1. You may use a coin to pry the remote control halves apart 2. Remove the old battery and replace with a new one 3. Be sure to observe the (+) sign when inserting the new battery. 4. Before assembling transmitter case, you should test the remote control. Note: LED icon of 2way transmitter indicates firstly blue color and then change to RED color when you press any button. In this case, its time to change CR2025 battery newly Description of Antenna Appearance 2Way Antenna Antenna Harness

<< Installation of Antenna >>

Note: Use the power of the antenna car battery 12volts. The Antennas have been calibrated for horizontal installation at the left-top corner of the windshield. Remote-Starting your Vehicle Remote-Starting For the 2-way remote:

display the KEY icon. For the 1-way remote:

system gives up. following:

brake) 1. Press the button one time. The remote will beep once and display the Lock icon. Then, press the button within 2 seconds. The remote will beep once and 2. 5 seconds later, the remote will activate starter. The Key icon will be shown with 3 different tones of beeping then the LED Icon will be scrolled.. 1. Press button one time and Lock LED will be displayed. Then press button for 2 seconds within 3 seconds. 2. Remote Stop - Press button for 2 seconds. If your vehicle does not start at the first attempt, the system will shut down, wait a few seconds and try to start the engine again. There will be 3 start attempts before the Note: Please make sure press to button only after LED lighting ends to activate each feature properly. Driving Off (Steps from Remote Start to Driving) With the vehicle running remotely, press button 2 times to disarm the OEM Starter Kill and/or the OEM alarm and unlock the doors. Enter the vehicle and do the 1. Turn the ignition key to the IGNITION ON (RUN) position.

(Do not turn the key to the CRANK position while the engine is running. This would cause the starter motor to reengage. Disarm the remote starter mode by pressing the foot 2. Press the brake pedal to disengage the remote starter unit. With the vehicle key is in the IGNITION ON position, press the brake pedal or wait 30 seconds for the vehicle to turn to ready status to drive. After pressing button once, if you press button 2 times within 3 seconds, remote starter will be operated. Once remote starter is succeeded and the engine is turned on, the remote will receive signal and shows the remaining remote starter time as a START LED icon. Note: In remote engine start status, engine will be deactivated according to following conditions.

- Open the door and 30 seconds is passed.

- Press brake pedal without key is in IGNITION ON position. Engine Run Time Your Remote Car Starter can be programmed to run the engine for 10 or 5 minutes (10 minutes by default). Note : Run time is set by installer. To check the amount of runtime remaining (2-way only):

If remote engine starter fails, the vehicle will not be started and the horn will sound accordingly to the table below. Number of Horn times Remote Start Error Remote Starter Features Remote Start Error Diagnostic 1 2 3 4 5 6 Hood open KEY IN or IG1 ON Valet mode Brake press Trunk open Door open Valet/Service Mode For REMOTE Start KEY Fob Valet/Service mode is used to prevent the system from unexpectedly starting the engine while being serviced. When your vehicle is in Valet Mode, the remote starter functionalities are disabled. If the vehicle needs to be serviced, or if you park it indoors, the Valet Mode will prevent the engine from being remote-started accidentally. Any of the following features will put your remote car starter into Valet Mode :

Remote Valet:

This feature allows you to put your system into Valet Mode by using the transmitter. To Engage Valet Mode/Service Mode: (Approaching to Function stop mode) 1) Insert the vehicles key to the IGNITION, turn to the ON position. 2) Press and hold the vehicle brake. 3) Press and hold the remote button for 2 seconds, the key LED will flash and the vehicles indicator will flash 1 time. Valet mode is engaged. To take the system out of Valet Mode (Return the system to its normal operating mode): (Disarming Function Stop Mode) 1) Insert the vehicles key to the IGNITION, turn to the ON position. 2) Press and hold the vehicle brake. 3) Press and hold the remote button for 2 seconds, the key LED will flash and the vehicles indicator will flash 2 times, Valet mode is cancelled. To verify whether the system is in Valet Mode using the 2-way remote:

If system is in Valet mode, buzzer sounds shortly when lock or unlock button is pressed. Advanced Features: Installation-programmable Options your vehicle. The Remote Car Starter was designed with flexibility and OEM integration in mind. With its programmable options, this unit can virtually control nearly any electrical system in Caution: The programming of your system should be left to a professional. Changing any one of the settings may affect the operation of your Remote Car Starter. Engine Run Time setting Option Setting Condition Disarm the vehicle with remote control transmitter.(Unlock) Driver s door must be physically Open, Engine Stop, Ignition ON, Trunk Open and Hood Open. Option Setting Instruction

- Under option setting condition, press button for 2 seconds. Light and Horn of vehicle will activate according to Engine Run Time option. Number of Indicator+ Horn Settings 1 Time 2 Times 10 Mins (Default) 5 Mins Light Blinking during remote engine start Option Setting Condition Disarm the vehicle with remote control transmitter.(Unlock) Option Setting Instruction

- Under option setting condition, press button for 2 seconds. Number of Indicator+ Horn Status 1 Time 2 Times Blink OFF (Default) Blick ON Driver s door must be physically Open, Engine Stop, Ignition ON, Trunk Open and Hood Open. Light and Horn of vehicle will activate according to Light Blinking during remote engine start. Pairing Remote Start Fob The Remote Start Fobs in Remote Start Kit are already paired with the main module at the time of production. There is no need to pair the Fobs at the time of the first installation. 1. When a new registration is needed

- When replacing a remote due to loss or malfunction of a remote.

- When replacing the main controller installed in the vehicle.

- When adding or changing the remote upon users need. 2. Pairing procedure 5X 1) Open drivers door and trunk. 2) Insert the key into the ignition. Turn the key from OFF to ON position 5 times within 5 seconds. 3) After step 2), within 5 seconds, Press button on the 1st Remote Start Fob 1 time. 4) After registering the 1st Remote Start Fob, within another 5 seconds, Press button on the next 2nd Remote Start Fob 1 time. 5) Verify that all Fobs are functioning correctly by performing Lock / Unlock function. NOTE:

1) A system can recognize up to 3 remotes maximum. 2) If a new Fob, or additional Fob, is needed later, the Fob pairing process should be done with the original Fob or oldest available Fob. Troubleshooting Poor Transmitting Range Many factors may affect the operating range of the transmitter. Some of these are:

-The condition of the batteries in the transmitter.

-The operating environment (for example: downtown radio-frequency noise, airports, cellular phone towers, etc).

-Metal in the area of the vehicle of transmitter. This includes the vehicle itself.

-The shape of the vehicle can affect range as well. Vans in general have greater interference. The shape of the roof and A-pillars causes considerable radio-frequency interference. Demonstrate to users that the best range is facing the vehicle's front. The worst range is facing the vehicles right or left side. Please inform the users that facing the vehicles front offers the best range. The worst range is experienced facing the R or L side.

-The amount of other vehicles in the area of the target vehicle.

-The method of using the transmitter. Always hold the transmitter high, approximately at shoulder height. Automatic Engine Start Repeat Remote Start is programmed to repeat the engine start sequence two (2) more times after ten (10) seconds if the engine start fails because of low vehicle battery. RF Specification 1. RF Transmitter Characteristics : 907MHz ~ 919MHz (Ch: 7) , DSSS

Label and Location ANT-2WDSS Label SIZE 15.7 X 8.9 mm This label is attached to the back of the product and not easily removed.

SEGI LIMITED Date: 18th of May, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. UL Verification Services Inc. (formerly UL CCS) Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern:

I, the undersigned, hereby authorize UL-Korea and hereafter referred to as ULK, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL-Korea on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing ULK as our agent, we still recognize that we are responsible to:

a) b) c) d) comply with the relevant provisions of the certification program;

make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) f) g) h) i) j) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, By Young il Chang President SEGI LIMITED REMARK:

1. This authorization letter will be sent along with your application when filing with the Certification Division. Please follow the format and type it on company letterhead and send original to us. Authorized signature must be in agreement with grantee code contact in FCC database. 2. 3.

UNIT S, 3-F, HARIBEST INDUSTRIAL BUILDING, 45-47, AU PUI WAN STREET, SHATIN, NT, SEGI LIMITED HONGKONG Date: May 18, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It may Concern:

RE: Request of Confidentiality for FCC ID: VA5ANB300-2WSS Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, SEGI LIMITED. Here by requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give SEGI LIMITED. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows:

PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description PERMANENT SHORT-TERM 1 2 3 4 5 6 7 8 Block Diagram Schematics Part Lists Operation Description NA NA NA NA The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Young il Chang Sincerely, President