FCC ID: VA5RCJ500-2WLR Keyless Entry System

User Manual By Firstech LLC, Version: 1.0 Applicable to the following remote(s);

2WT13R-SF 2Way 3Button LCD Remote Model Name FCC ID IC Number 2WT13R-SF ANT-2WSF VA5RCJ500-2WLR 7087A-2WRCJ500LR VA5ANH500-2WLF 7087A-2WANH500LF WWW.COMPUSTAR.COM WARNING It is the responsibility of the vehicle operator to ensure that their vehicle is parked in a safe and responsible manner.

(1) When leaving the vehicle, it is the users responsibility to ensure that the gearshift lever is in Park in order to avoid accidents upon remote starting. (Note: Make sure that the automatic vehicle cannot star in Drive.)

(2) It is the users responsibility to ensure that the remote starter is disabled or put into valet mode before FCC COMPLIANCE servicing. operation. IC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this device. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) Lappareil ne doit pas produire de brouillage;

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure Statement This device complies with FCC radiation exposure limit set forth for an uncontrolled environment. For ANT-2WSF: This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. RF Specification 2WT13R-SF : 907 ~ 919 (7CH) DSSS ANT-2WSF : 907 ~ 919 (7CH) DSSS / 125 LF transmitter Introduction Thank you for purchasing a Firstech system for your vehicle. Please take a minute to review this entire manual. Note that this manual applies to the 2 Way 3 Button Liquid Crystal Display Remote

(2WT13R-SF) whether you purchased the ALARM IT, START IT, or MAX IT system. There are certain features listed in this manual that may not be available for your system. There may also be features listed in this manual that require additional installation or programming before they are active. If you have any questions or concerns please contact the original place of purchase. For further information you may also contact our customer support center at 888-820-3690. Warranty Coverage Caution: The Manufacturers warranty will be voided if this product is installed by anyone other than an Authorized Firstech dealer. For complete warranty details visit www.compustar.com or the last page of this manual. Firstech remotes carry a 1 year warranty from original date of purchase. Compustar Pro 2WT13R-SF remote carries a 3 year warranty. Warranty registration can be completed online by visiting www.compustar.com. Please complete the registration form within 10 days of purchase. We do not include a mail in warranty registration card with each unit registration must be done online. To verify that an authorized dealer installed your system, we highly recommend that you keep a copy of the original proof of purchase, such as the dealer invoice in a safe place. Remote Image Quick Reference Remote Maintenance Battery Charging The 2WT13R-SF comes with a rechargeable battery. Use the included power adapter and micro USB cable to charge your remote. First, locate the micro USB port on the top of your remote. Connect your micro USB cable to your computer or USB power adapter. The LCD on the front of the remote will showing that your remote is charging. This should take approximately 2 hours. 2 Way Remote Button Functions Button Description Duration half second Double Tap Long Hold

(2.5 sec) Short

(0.5 sec) Double Long Hold

(2.5 sec) Short(0.5 sec) Double Long Hold

(2.5 sec) Long Hold

(2.5 sec) Long Hold

(2.5 sec) Locks doors and if equipped, arms the alarm. Used as Auxiliary 2 and Sliding door left, Head lights function according to the setting of AUX 2 Config in the remote menu. Not available when set to OFF in AUX 2 Config of the remote menu. Panic/vehicle locater (flashes vehicles parking lights and sounds siren and horn). LCD View / Car Check (updates vehicle status on remote pager) / Secure Auxiliary / Temperature Display /

Vehicle Voltage Display Accesses Remote Menu (LCD View, Passive arming, Alert mode, etc) See Remote Menu Table for details. Run time extender. Resets the run time for Turbo Timer or Remote Start. Holding this button will start your vehicle. Repeat and this will shut your vehicle down. Unlocks doors and if equipped, disarms the alarm. Used as Auxiliary 1 and Sliding door right, Defrost function according to the setting of AUX 1 Config in the remote menu. Not available when set to OFF in AUX 1 Config of the remote menu. Trunk release. Triggers the trunk release output and opens the vehicles trunk. Option programming menu 1. For use during installation. Option programming menu 2. For use during installation.

Function Button Menu Button Duration Description Half second Move to the left of the remote menu 2.5 seconds The remote menu moves to LCD View. Half second Remote menu selection and operation. 2.5 seconds The remote menu exits manually. Half second Move to the right of the remote menu 2.5 seconds The remote menu moves to Power down. Remote Option Menu Table Feature Select Function / Description LCD View Select the vehicle type (Sedan, SUV, Pickup) on the main screen. Passive arming Passive arming On/Off Valet mode Valet mode On/Off Sets your remote for Alarm or Starter Only systems. Set to FULL for ALARM IT and MAX IT features. Set to HALF for START IT ONLY systems. Used as Auxiliary 1 and Sliding door right, Defrost function according to the setting of AUX 1 Config in the remote menu. Used as Auxiliary 2 and Sliding door left, Head lights function according to the setting of AUX 2 Config in the remote menu. Turns your Auxiliary Extender feature on or off. Changes LCD display language from English to French or Spanish. Alert mode AUX 1 config AUX 2 config AUX Mode Language Tempurature REMOTE ID POWER Down Sound/Vibration Display brightness Screen timeout Changes the temperature readout from Fahrenheit to Celsius. If the temperature setting is set to off, the temperature is not displayed. Displays the electrical product number of the remote. Switch the remote product to power down mode. Turns the silent mode on or off. Adjust the volume of your remote. 1 is the lowest. 3 is the highest. Adjust the screen brightness in 3 steps. Adjusts the time your LCD will stay on after a button is pressed. Turbo timer Turbo On/Off Timer start Timer Start On/Off Drive lock Drive Lock On/Off 2nd car mode 2nd Car Mode On/Off Shock sensor Shock sensor On/Off Siren Siren On/Off Proximity Proximity On/Off Auxiliary Extender Button Table Button Duration Description Half second Auxiliary 1 Double Tap Auxiliary 7 2.5 seconds Auxiliary 3 Half second Auxiliary 5 Double Tap Accesses Remote Menu. 2.5 seconds Auxiliary 6 Half second Auxiliary 2 2.5 seconds Auxiliary 4 Description of antenna module installation position

<< Antenna Module >>

<< Harness >>

<< Installation of Antenna Module >>

Note: Use the power of car battery(+12volts). The Antenna module have been calibrated for horizontal installation at the left-top corner of the windshield. Remote Coding / Programming Routine IMPORTANT: Every Firstech remote must be coded to the system prior to performing any operations. All remotes must be coded at the same time. Programming 2 Way 4 Button Remotes:

STEP 1: Activate Valet/Programming mode by manually turning the ignition key on and off (between the Acc & On positions) five times within 10 seconds. The vehicles parking lights will flash once with the successful completion of this step. STEP 2: Within 2 seconds after cycling the ignition for the 5 remotes or the (lock) button on 1 way remotes for a half second. The parking lights will flash once to confirm the transmitter has been coded. time, tap the Lock button on 2 way th Exiting Programming: Programming is a timed sequence. The parking lights will flash twice signaling the end of programming mode. Programming Multiple Remotes: After the confirmation flash given in step 2, code additional remotes by pressing button (I) on 2 way remotes or the (lock) button on 1 way remotes. The parking lights will flash once confirming each additional remote. All compatible systems can recognize up to 4 remotes. Remote Start Error Diagnostic If the remote start fails to start the vehicle, the parking lights will flash three times immediately. Following those three flashes the parking lights will flash again corresponding to the error table. Number of Parking Light Flashes Remote Start Error Motor running or must first program tach Key in ignition on position Door open (manual transmission only) Trunk open Foot brake on Hood open Reservation off (manual transmission only) Tach or tachless sensing failure FT-DAS sensor shutdown System is in Valet Mode 1 2 3 4 5 6 7 8 9 10 We recommend that you do not attempt any repairs on your remote starter. Contact your dealer or call us directly. Remote Start Shutdown Error Codes If the remote start sequence has been completed and the vehicle shuts down, the vehicles parking lights will flash 4 times, pause then flash again with the error code. Tap button 4 on 2 Way remotes to initiate the shutdown error codes. On 1 Way remotes hold the Trunk and Start buttons together for 2.5 seconds. Number of Parking Light Flashes Remote Start Shutdown Error 1 2 3 4 Lost engine sensing signal Lost emergency brake signal Foot brake triggered Hood pin triggered Limited Lifetime Warranty Firstech, LLC Warrants to the original purchaser that this product shall be free of defects in material and workmanship under normal use and circumstances for the period of time that the original owner of this product owns the vehicle in which it is installed; except that the remote controller unit for the period of one year from the date of installation to the original owner of this product. When the original purchaser returns the product to the retail store where it was purchased or prepaid postal to Firstech, LLC., 21903 68th Avenue South, Kent, WA 98032, USA within the warranty period, and if the product is defective, Firstech, LLC, will at its option repair or replace such. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO, THE EXCLUSION OF ANY AND ALL WARRANTY OF MERCHANTAPILITY AND/OR ANY AND ALL WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL WARRANTY OF NON-INFRINGEMENT OR PATENTS, IN THE UNITED STATES OF AMERICA AND/OR ABROAD. NEITHER THE MANUFACTURER OF ANY ENTITIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights, which vary State to State. Firstech, LLC. is not RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE that may or may not resulted from the operation of Compustar, Compustar Pro, Arctic Start, Vizion, or NuStart. NOT WITH STANDING THE ABOVE, MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Your Warranty The product's warranty is automatically void if the date code or serial number is defaced, missing or altered. This warranty will not be valid unless you have completed the registration card at www.compustar.com within 10 days of purchase.

Label and Location 2WT13R-SF Size Label 14.6 X 13.8 mm This label is attached to the back of the product and not easily removed.

SEGI LIMITED Date: 26 th of June, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. UL Verification Services Inc. (formerly UL CCS) Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern:

I, the undersigned, hereby authorize UL-Korea and hereafter referred to as ULK, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL-Korea on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing ULK as our agent, we still recognize that we are responsible to:

a) b) c) d) comply with the relevant provisions of the certification program;

make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) f) g) h) i) j) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, By Young il Chang President SEGI LIMITED REMARK:

1. This authorization letter will be sent along with your application when filing with the Certification Division. Please follow the format and type it on company letterhead and send original to us. Authorized signature must be in agreement with grantee code contact in FCC database. 2. 3.

CONFIDENTIALITY REQUEST Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 2020.06.26 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, SEGI LIMITED requests confidentiality for the following products:

FCC ID Number Product VA5RCJ500-2WLR Title/Model Keyless Entry System / 2WT13R-SF The following exhibits contain trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our product. This material is not customarily available to the general public and we request that it be withheld from public inspection. We request that the following information submitted be held permanent confidential treatment. Permanent Confidential Request

Schematics Block diagram Part List Operational description Short- term Confidential Request

Internal photo Best regards, We request that the following information submitted be held short-term confidential treatment for 180 days. If you have any questions, please feel free to contact me at the address shown below. Name: Young il Chang Title: President Company name: SEGI LIMITED Unit J2, 4/F, Block 1, Kinho Industrial Building, 14-24 Au Pui Wan Street, Shatin, New Territories HONGKONG E-MAIL : Segihk@gmail.com