USA - Federal Communications Commission (FCC) FCC Radiation Exposure Statement Interference Statement These devices comply with Part 15 of the FCC Rules. Operation of the devices is subject to the following two conditions: (1) The devices may not cause harmful interference, and (2) The devices must accept any interference that might cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, the equipment might cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures:
Relocate this device. Increase the separation between the device and the receiver. Connect the device into an outlet on a circuit different from that of other electronics. Consult the dealer or an experienced radio technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following:
Contains FCC ID: BKMFBWLU6117. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Canada. Industry Canada (IC) This device complies with RSS210 of Industry Canada. CAUTION: Exposure to Radio Frequency Radiation. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population. Consult Safety Code 6, obtainable from health Canadas website www.hc-sc.ca/rpb. Ce dispositif est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC:
1052C-WLU6117. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 20cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 1052C-WLU6117". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. This device is intended only for OEM integrators under the following conditions:
(For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20 cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. Europe. EU Declaration of Conformity This equipment complies with the essential requirements of the European Union directive 1999/5/EC. SEIKO EPSON CORPORATION , 1999/5/EC. etina SEIKO EPSON CORPORATION tmto prohlauje, e tento Wireless Device je ve shod se zkladnmi poadavky a dalmi prslunmi ustanovenmi smernice 1999/5/ES. Dansk Undertegnede SEIKO EPSON CORPORATION erkl rer herved, at f lgende udstyr Wireless Device overholder de v sentlige krav og vrige relevante krav i direktiv 1999/5/EF. Deutsch Hiermit erklrt SEIKO EPSON CORPORATION, dass sich das Gert Wireless Device in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. English Hereby, SEIKO EPSON CORPORATION declares that this Wireless Device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Eesti Kesolevaga kinnitab SEIKO EPSON CORPORATION seadme Wireless Device vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. Espa ol Por medio de la presente SEIKO EPSON CORPORATION declara que el Wireless Device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. E SEIKO EPSON CORPORATION Wireless Device 1999/5/. Franais Par la prsente SEIKO EPSON CORPORATION dclare que l'appareil Wireless Device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano Con la presente SEIKO EPSON CORPORATION dichiara che questo Wireless Device conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. slensk Hr me lsir SEIKO EPSON CORPORATION yfir v a Wireless Device er samr mi vigrunnkrfur og arar krfur, sem gerar eru tilskipun 1999/5/EC. Latvieu Ar o SEIKO EPSON CORPORATION deklar, ka Wireless Device atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi k. iuo SEIKO EPSON CORPORATION deklaruoja, kad is Wireless Device atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Magyar Alulrott, SEIKO EPSON CORPORATION nyilatkozom, hogy a Wireless Device megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Maltese Hawnhekk, SEIKO EPSON CORPORATION, jiddikjara li dan Wireless Device jikkonforma mal-tiijiet essenzja ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Nederlands Hierbij verklaart SEIKO EPSON CORPORATION dat het toestel Wireless Device in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Norsk SEIKO EPSON CORPORATION erkl rer herved at utstyret Wireless Device er i samsvar med de grunnleggend krav og vrige relevante krav i direktiv 1999/5/EF. Polski Niniejszym SEIKO EPSON CORPORATION owiadcza, e Wireless Device jest zgodny z zasadniczymi wymogam oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Portugus SEIKO EPSON CORPORATION declara que este Wireless Device est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE. Romn Prin aceasta, SEIKO EPSON CORPORATION declar c acest Dispozitiv Wireless este n conformitate cu cerin eseniale i alte dispoziii relevante ale Directivei 1999/5/CE. Slovenina SEIKO EPSON CORPORATION tmto vyhlasuje, e Wireless Device spa zkladn poiadavky a vetky prslu ustanovenia Smernice 1999/5/ES. Slovenina SEIKO EPSON CORPORATION izjavlja, da je ta Wireless Device v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES. Suomi SEIKO EPSON CORPORATION vakuuttaa tten ett Wireless Device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Svenska Hrmed intygar SEIKO EPSON CORPORATION att denna Wireless Device str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. France In all Metropolitan dpartements, wireless frequencies can be used under the following conditions, either for public or private use:
Indoor use: maximum power (EIRP) of 100 mW for the entire 24002483.5 MHz frequency band. Outdoor use: maximum power (EIRP) of 100 mW for the 24002454 MHz band and with maximum power (EIRP) of 10 mW for the 24542483.5 MHz band. Taiean NCC Statement 1. 2. 3. Note: 1. 2.
XXXyyyLPDzzzz-x
(NCC ID)