FCC ID: BKMAE-H931RX LCD Projector

 

Useful Functions b Check the status of the WiHD indicator on the WirelessHD Transmitter. If the WiHD indicator is on, go to the next step. If the indicator is off, press the WirelessHD Transmitter. Make sure you point the remote control at the WirelessHD Transmitter when using the on the remote control. button on the remote control or the button on the button Remote control WirelessHD Transmit-

ter c Check the status of the Link indicator on the WirelessHD Transmitter. If the WirelessHD Transmitter is connected to the projector, the Link indicator turns on. c If the indicator does not turn on, check that the projector has been prepared correctly and that You can view the signal strength while images are being projected from the WirelessHD settings it is turned on. menu. s Settings - WirelessHD - Video Reception p.75 55 Useful Functions d If projection does not start, press the source. Make sure you point the remote control at the projector when using the control. button on the remote control to change the button on the remote Projection starts. button to switch images. s p.60 e When connecting two or more AV devices to the WirelessHD Transmitter, press the c When receiving WirelessHD images, make sure WirelessHD is set to On from the Configuration menu. Make sure you turn off the WirelessHD Transmitter if it is not going to be used for an extended period. s Settings - WirelessHD - WirelessHD p.75 WirelessHD Settings Menu a Press the button. The Configuration menu is displayed. c Make settings for each of the displayed functions. b Select Settings - WirelessHD, and button to confirm then press the the selection. The WirelessHD settings screen is displayed. Available functions on the WirelessHD settings menu Function Connected Device WirelessHD Video Reception Reset Explanation Displays the available WirelessHD device that can be connected. The device name and MAC address (device number) are displayed. The MAC address is displayed on the label on the base. Enables or disables the WirelessHD function. Displays the reception for the image being projected. Resets WirelessHD settings to their default settings. 56 Useful Functions c Even when the WirelessHD Transmitter and the projector are connected, 0% is displayed as the Video Reception when no image signal is being input. Check the communication status by viewing the Link indicator.s p.48 WirelessHD Transmission Range The following shows the communication range of the WirelessHD. Make sure you set up the WirelessHD Transmitter so that it faces the projector. Horizontal

* Install the transmitter at 70when you use it in Taiwan or Korea. Vertical direction (suspended from a ceiling) Vertical direction (placed on a table and so on) c The wireless transmission range varies depending on the placement and material of the surrounding The projector cannot communicate through walls. The antennas are built-into the front of the projector and the WirelessHD Transmitter. Make sure the furniture and walls. The values given here are for your reference only. antennas face each other (face the front) when setting up the devices. Also, do not place any object over the front side of the projector and WirelessHD Transmitter. Do not install the transmitter on a metal shelf. The metal may make the signal unstable. Install on a shelf made from wood etc. When checking operations, place the projector and the WirelessHD Transmitter close to each other, and make sure there are no other projectors operating in the vicinity. Depending on the reception strength, the image's color information may be automatically discarded to avoid any interruptions and maintain a constant connection. To avoid any deterioration in image quality, adjust the position of the WirelessHD Transmitter so that the Video Reception is as strong as possible. Reception sensitivity varies depending on the resolution of the input image. Therefore, you may not be able to achieve the same reception sensitivity when inputting a 1080p image and when inputting a 4K image. 57 Useful Functions Operating the Remote Control Name Function Turns the power for the WirelessHD Transmitter on or off. Switches the output image between a monitor device, such as a television, connected to the HDMI Out port on the WirelessHD Transmitter and the projector.s p.59 Switches the image source for the AV device connected to the WirelessHD Transmitter. s p.60 a b c c Point the remote control towards the WirelessHD Transmitter. Remote Control Operating Range The following shows the operating range between the remote control and the WirelessHD Transmitter. Operating range (left to right) Operating range (top to bottom) Switching the Input and Output With the WirelessHD Transmitter, you can connect and switch between up to four multi-media players (input devices to be played back) and one monitor device (a monitor device displaying an image, such as a television). button to switch between input Point the remote control at the WirelessHD Transmitter and press its devices and its button to switch between output devices. 58 Useful Functions Switching the target image You can switch between a monitor device, such as a television, connected to the HDMI Out port on the WirelessHD Transmitter and the projector. a Turn on the projector or the monitor device, such as a television. b Turn on the WirelessHD Transmitter. The On/Standby indicator on the WirelessHD Transmitter turns on. c Point the remote control at the WirelessHD Transmitter, and then press the button on the WirelessHD Transmitter. on the remote control or the button Remote control WirelessHD Transmit-

ter Depending on the output target, the indicators on the WirelessHD Transmitter indicate the following status. The output target projected last time is projected the next time the projector is turned on. WiHD indicator On: The image is being output to the projector. TV indicator On: The image is being output to the monitor device. 59 Useful Functions c You can switch to the other monitor device even when the projector is off. Switching the image source Use the WirelessHD Transmitter. button on the remote control to switch the image source for the AV device connected to the 60 Useful Functions Using the HDMI Link Function HDMI Link Function When an AV device that meets the HDMI CEC standards is connected to the projector's HDMI port, you can perform linked operations such as linked power on and volume adjustment for the AV system from one remote control. Also, when projecting images in WirelessHD, you can use the HDMI link function (EH-

TW9400W/EH-TW8400W only). c As long as the AV device meets the HDMI CEC standards, you can use the HDMI link function even if Up to 3 multi-media players that meet the HDMI CEC standards can be connected at the same time. the AV system in-between does not meet the HDMI CEC standards. Connection Example Projector Amplifier Multi-media players and so on HDMI Link Settings When HDMI Link is set to On, you can perform the following operations. s Settings - HDMI Link - HDMI Link p.75 Input Change Link Changes the input source of the projector to HDMI when content is played back on the connected device. Connected Devices Operations Using the projector's remote control, you can perform op-

erations such as Play, Stop, Fast Forward, Rewind, Next Chapter, Previous Chapter, Pause, Volume Adjustment, and Audio Mute. You can also select the following functions from the HDMI Link screen. Function Audio Out Device*

Power On Link Explanation Selects which device outputs audio. AV System: Select this setting when you output audio from an AV amplifier. WiHD Transmitter (Optical): Select this to output audio from the device connected to the Optical Audio-Out port on the WirelessHD Transmitter. WiHD Transmitter (HDMI): Select this to output audio from the device connected to the HDMI Out port on the WirelessHD Transmitter. When Power On Link is set, operations are linked as shown below. When the projector is turned on, the connected devices are also turned on. Also, when the connected devices are turned on and content is played back, the projector turns on. However, the projector does not turn on when connected to the WirelessHD Transmitter even when the connected device is turned on. 61 Useful Functions Function Power Off Link Explanation When Power Off Link is set to On, when the projector is turned off, the connected devices are also turned off. This only works when the connected device's CEC power link function is enabled. Note that depending on the status of the connected device (for example, if it is record-

ing), the device may not power off. Link Buffer If HDMI Link is not working correctly, you may be able to improve it by changing the settings.

* EH-TW9400W/EH-TW8400W only. c To use the HDMI Link function, you must configure the connected device. See the documentation supplied with the connected device for more information. Connecting You can check the connected devices that are available for HDMI Link, and select on the device you want to project the image from. Devices that can be controlled by HDMI Link automatically become the selected device. Before displaying the list of connected devices, check that HDMI Link is set to On. s Settings - HDMI Link - HDMI Link p.75 a Press the button, and then select Device Connections. The Device Connections list is displayed. Devices that have an aqua icon to their left are linked by HDMI Link. If the device name cannot be determined this field is left blank. b Select the device you want to operate using the HDMI Link function. c If the cable does not meet the HDMI standards, operations are not possible. Some connected devices or functions of those devices may not operate properly even if they meet the HDMI CEC standards. See the documentation and so on supplied with the connected device for more information. 62 Using the Projector on a Network Projecting Using Wired LAN You can send images to your projector through a wired network. To do this, connect the projector to your network, and then set up your projector and computer for network projection. When you have finished making projector connection and network settings, install Epson iProjection

(Windows/Mac) from the following Web site. You can use Epson iProjection to project computer images over a network. You can also hold dynamic meetings by projecting images from multiple computers connected to the network at the same time. See the Epson iProjection Operation Guide (Windows/Mac) for more information. http://www.epson.com Selecting Wired Network Settings Before you can project from computers on your network, you need to select network settings on the projector. c Before making settings, connect a LAN cable to the LAN port, and connect the projector to the wired LAN. a Press the button to display menus in the order Network - Network Configuration. b Select Basic, and then set the following as necessary. Projector Name: Enter a name up to 16 alphanumeric characters long to identify the projector over the network. PJLink Password: Set a password to use when you control the projector using compatible PJLink software. You can enter up to 32 single-byte alphanumeric characters. Remote Password: Set a password to use when you operate the projector from a smartphone or a tablet. You can enter up to 8 single-byte alphanumeric characters. Display LAN Info.: Set the display format for the projector's network information. c Use the displayed keyboard to enter the name, passwords and keyword. Press the buttons on the remote control to highlight characters, and then press the button to enter them. c Select Wired LAN, and then press the button. 63 Using the Projector on a Network d Select the basic options as necessary. If your network uses DHCP, set DHCP to On. If you are not using DHCP, set DHCP to Off, and then enter the projector's IP Address, Subnet Mask, and Gateway Address. e When you have finished making settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. f Press the button on the remote control. The settings are complete when you see the correct IP address on the LAN standby screen. c To prevent the IP address from being displayed on the LAN standby screen or the Home screen, set IP Address Display to Off. s Network - Network Configuration - Wired LAN p.84 64 Using the Projector on a Network Projecting Using Wireless LAN You can project images from smartphones, tablets, and computers over wireless LAN. To project over wireless LAN, you need to make wireless network settings for the projector and the connected device in advance. Use Epson iProjection to project images over wireless LAN. You can download Epson iProjection using any of the following methods; however, the customer is liable for any costs involved. You can download Epson iProjection (Windows/Mac) from the following Web site. http://www.epson.com You can download Epson iProjection (iOS/Android) from the App Store or Google Play. Selecting Wireless Network Settings Manually Before you can project from your wireless network, you need to select network settings for the projector. a Press the b Use the button to display menus in the order Network - Wireless LAN Power. buttons to select On, and then press the button. c Select Network Configuration, and then press the button. 65 Using the Projector on a Network d Select Basic, and then set the following as necessary. Projector Name: Enter a name up to 16 alphanumeric characters long to identify the projector over the network. PJLink Password: Set a password to use when you control the projector using compatible PJLink software. You can enter up to 32 single-byte alphanumeric characters. Remote Password: Set a password to use when you operate the projector from a smartphone or a tablet. You can enter up to single-byte 8 alphanumeric characters. Display LAN Info.: Set the display format for the projector's network information. c Use the displayed keyboard to enter the name, passwords and keyword. Press the buttons on the remote control to highlight characters, and then press the button to enter them. e Select Wireless LAN, and then press the button. f Select the Connection Mode setting. Quick: Lets you connect the projector to your smartphones, tablets, or computers directly using wireless communication. When you select Quick, go to step 10. Advanced: Lets you connect the projector to multiple smartphones, tablets, or computers over a wireless network access point. When you select Advanced, go to step 7. g Select Network Configuration - Wireless LAN - Search Access Point, to select the access point you want to connect to. c If you need to assign the SSID manually, select SSID to enter the SSID. In addition, configure the security settings in the Security menu.s p.68 66 Using the Projector on a Network h Assign an IP address to the projector as necessary. If your network uses DHCP, select IP Settings to set the DHCP setting to On. If you are not using DHCP, select IP Settings to set the DHCP setting to Off, and then enter the projector's IP Address, Subnet Mask, and Gateway Address. i When you have finished selecting settings, select Complete and then follow the on-screen instructions to save your settings and exit the menus. j Press the correct IP address on the LAN standby screen. button on the remote control. The settings are complete when you see the When you have finished making wireless settings for your projector, you need to make wireless settings on the connected device. Then start the network software to send images to your projector through a wireless network. c To prevent the SSID and IP address from being displayed on the LAN standby screen or the Home screen, set SSID Display and IP Address Display to Off. s Network - Network Configuration -

Wireless LAN p.83 Selecting the Computer's Wireless LAN Settings Before connecting to the projector, select the correct wireless network on your computer. Selecting wireless network settings in Windows a To access your wireless utility software, double-click the network icon on the Windows taskbar. b When connecting in Advanced connection mode, select the network name (SSID) of the network the projector is connecting to. c Click Connect. Selecting wireless network settings in OS X a Click the AirPort icon on the menu bar at the top of the screen. 67 Using the Projector on a Network b When connecting in Advanced connection mode, make sure AirPort is turned on and select the network name (SSID) of the network the projector is connecting to. Setting Up Wireless Network Security You can set up security for your projector to use on a wireless network. Set up one of the following security options to match the settings used on your network:

WPA2 security WPA/WPA2 security a Press the

- Security. button to display menus in the order Network - Network Configuration b Select the security settings to match your network settings. c When you have finished making settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. Projecting in Epson iProjection (iOS/Android) You can display a QR code on the screen and project data easily from a smartphone or tablet using the Epson iProjection app (V1.3.0 or later). c You can download Epson iProjection free of charge from App Store or Google Play. Any fees incurred when communicating with the App Store or Google play are the responsibility of the customer. When using Epson iProjection in Quick connection mode, we recommend making security settings.s p.68 a Press the b Use the button to display menus in the order Network - Wireless LAN Power. buttons to select On, and then press the button. c Display the Network Configuration - Basic - Display LAN Info. menu. 68 Using the Projector on a Network d Use the buttons to select Text & QR Code, and then press the button. e Press the button on the remote control or select Display the QR Code in the projector's Network menu to display the QR code. c If you press the button, you can also display the QR code from the Home screen.s p.26 If the projector is already receiving an image signal over the network, the QR code is not button. Select Display the QR Code from the displayed even if you press the Network menu to display the QR code. To hide the QR code, press the button. f Start Epson iProjection on your smartphone or tablet. g Read the projected QR code using Epson iProjection. Read the code from in front of the screen so that the QR code fits into the guide. If you are too far from the screen, the code may not be read. Once connected, go to and select the Contents menu, and then select a file you want to project. Operating using a smartphone (remote control function) in Epson iProjection to display the menu. By using Epson iProjection, you can operate the projector from a smartphone or tablet. Tap Tap Remote on the menu to display the following screen. c When Remote Password is set, you need to enter the password. Once the password has been recognized, you do not need to enter it from the second time. 69 Using the Projector on a Network a b c d e f g h i j k l m n o Button Function Displays the menu. Turns the projector on or off. Changes to the image from each input port. s p.26 Sets the image quality using the on-screen instructions. Saves, loads, erases, or rename a memory. s p.42 Turns HDMI Link on or off. s p.61 When HDMI Link is On, you can perform operations such as Play, Stop, Fast Forward, Rewind, Next Chapter, Previous Chapter, and Pause. Sets the Color Mode, Frame Interpolation, Image Enhance-

ment, Color Temp., Gamma, RGBCMY,Lens Iris, Power Con-

sumption, and Auto Iris. Specify 3D Display, 3D Format, 3D Depth, Diagonal Screen Size, and 3D Brightness. Adjusts the focus, zoom, and lens shift. You can also register the lens position (Memory function) or display a test pattern (Pattern func-

tion). Specify Aspect, Image Processing, Keystone, Reset All Config, Reset Memory, Reset Lens Position, Lens Shift, Zoom, Focus, Test Pattern. When HDMI Link is set to On, you can adjust the volume. When HDMI Link is set to On, you can turn the image and audio on/

off temporarily. s p.31 Opens the touch pad screen. You can operate the Configuration menu by touching your touch pad. Selects the projector you want to control. 70 Configuration Menu Configuration Menu Functions Configuration Menu Operations On the Configuration menu, you can make adjustments and settings for Signal, Image, Input Signal, and so on. a Press the button. Remote control Control panel The Configuration menu is displayed. b Use the buttons to select the top menu on the left, and button to confirm then press the the selection. When you select the top menu on the left, the sub menu on the right changes. The line at the bottom is a guide for operations. c Use the buttons to select the sub menu on the right, and button to confirm then press the the selection. The adjustment screen for the selected function is displayed. d Use the adjust the settings. Ex.) Adjustment bar buttons to Ex.) Choices button on an item displaying icon to change to the selection Press the this screen for that item. Press the previous level. button to return to the e Press the menu. button to exit the 71 Configuration Menu c For items adjusted using an adjustment bar, such as the brightness level, you can press the button while the adjustment screen is displayed to return the adjustment value to its default value. Configuration Menu Table If there is no image signal being input, you cannot adjust items related to the Image or Signal in the Configuration menu. Note that the items displayed for the Image, Signal, and Info vary depending on the image signal being projected. Image menu Function Color Mode Brightness Contrast Color Satura-

tion Tint Sharpness Color Temp. Menu/Settings Explanation Dynamic, Bright Cinema, Natural, Cinema, Digi-

tal Cinema, 3D Dynamic, 3D Cinema Color Temp. Skin Tone Customized Grayscale Adjustment Level, Red, Green, Blue, Brightness Select a color mode based on your sur-

roundings and the image you are projec-

ting. s p.32 Adjusts the brightness when the image appears too dark. Adjusts the contrast between light and shade in the images. By increasing the contrast, the images become vivid. Adjusts the color saturation for the im-

ages. Adjusts the tint for the images. Adjusts the image sharpness. Adjusts the tint for the images. The image is tinted blue for high values, and tinted red for low values. Adjusts the skin tone. The image becomes greener when set to a positive value and redder when set to a negative value. Adjusts the offset and gain for each R, G, and B color. Adjusts red, green, blue, and brightness for the selected adjustment level. Adjusts the smoothness of movement of the image. Frame Interpo-

lation*1 Off, Weak, Normal, Strong 72 Configuration Menu Function Image En-

hancement*2 4K Enhancement Image Preset Mode Noise Reduction MPEG Noise Reduction Super-resolution Detail Enhancement Advanced Gamma RGBCMY R/G/B/C/M/Y Deinterlacing Explanation You can project at a doubled resolution. Fine Line Adjust, Soft Focus Detail Menu/Settings On, Off Off, Preset 1 to Preset 5 Select the settings prepared in advance as the settings for Noise Reduction, MPEG Noise Reduction, Super-resolution, and Detail Enhancement. Adjusts the roughness of the image. Smoothes out rough images in MPEG for-

mat. Adjusts the amount of enhancement for complicated images and backgrounds. Creates a more emphatic texture and ma-

terial feel of the image. Performs gamma adjustments. You can select a raw value or adjust using a custom value. s p.40 Adjusts the hue, saturation, and bright-

ness for each R, G, B, C, M, and Y color. s p.38

(This can only be set when Image Pro-

cessing is set to Fine or when receiving 480i, 576i, or 1080i signal input from the HDMI1, or HDMI2 ports or from Wire-

lessHD.) Converts the signal from interlaced (i) to progressive (p) using a method appropri-

ate for the image signal. Off: This is ideal for dynamic motion im-

Hue, Satura-

tion, Bright-

ness Off, Video, Film/Auto 2, 1, 0, -1, -2, Custom-

ized*3, Reset Lens Iris Power Con-

sumption High, Medium, ECO Auto Iris Off, Normal, High Speed Reset Yes, No ages. Video: This is ideal for viewing general video images. Film/Auto: Performs the optimal conver-

sion for film, CG, or animation input sig-

nals. Adjusts the amount of light entering the lens with the lens diaphragm, which ad-

justs the contrast of the image. You can set the lamp brightness to one of three settings. Select ECO if the images being projected are too bright. When ECO is selected, pow-

er consumption during projection decrea-

ses, and fan rotation noise is reduced. You can change the luminance adjust-

ment tracking for changes in brightness in the displayed image. s p.36 Resets the adjustment values of Image set in the current Color Mode to the default settings.

*1 Only when an HDMI1, HDMI2, WirelessHD image signal is being input. 73 Configuration Menu

*2 Only when an HDMI1, HDMI2, WirelessHD, or PC image signal is being input.

*3 Settings are saved for each type of input source or Color Mode. Signal menu The Signal menu cannot be set when a LAN image signal is being input. Function 3D Setup*1 Menu/Settings 3D Display Auto, 3D, 2D Side by Side, Top and Bottom

-10 to 10 60 to 300 3D Format 3D Depth Diagonal Screen Size 3D Brightness Inverse 3D Glasses Low, Medium, High Sets the brightness for the 3D image. Yes, No 3D Viewing Notice On, Off Aspect*2 Tracking*2 *4 Auto*1, Normal, Full, Zoom, Anamorphic Wide*3, Horiz. Squeeze*3 Varies depending on the input signal. Sync.*2 *4 0 to 31 Position*2 *4 Auto Setup*4 On, Off Overscan*1 *2 Auto, Off, 4%, and 8%

Explanation To view 3D images, set this to Auto or 3D. s p.44 Sets the 3D format for the input signal. Sets the depth for the 3D image. Sets the projection size for the 3D image. By matching this to the actual size, you can achieve the optimum 3D effect. Reverses the synchronization timing for the left/

right shutters on the 3D Glasses and the left/right images. Enable this function if the 3D effect is not displayed correctly. Turns the notice that appears when viewing 3D content on or off. Selects the aspect mode. s p.33 Adjusts computer images when vertical stripes appear in the images. Adjusts computer images when flickering, fuzzi-

ness, or interference appear in the images. Adjusting the Brightness, Contrast, or Sharp-

ness may cause flickering or fuzziness. When adjusting Sync. after adjusting the Track-

ing, you can create a more vivid image. Adjusts the display position up, down, left, and right when a part of the image is missing so that the whole image is projected. Sets whether or not to automatically adjust the image whenever the input signal is changed. When enabled, the Tracking, Position, and Sync. are automatically configured. Changes the output image ratio (the range of the projected image). Off, 4%, 8%: Sets the range of the image. When set to Off, the entire range of the image is pro-

jected. Depending on the image signal, you may notice noise at the top and bottom of the image. Auto: Automatically sets to Off or 8% depend-

ing on the input signal. Color Space*1 Auto, BT.709, BT.2020 Sets the conversion system for the color space. 74 Configuration Menu Function Dynamic Range*1 Menu/Settings Explanation Dynamic Range Signal Status HDR10 Setting Auto, SDR, HDR10, HLG

-

1 to 16 HLG Setting 1 to 16 Advanced Video Range*1 *2 Auto, Limited

(16-235), Full

(0-255) EDID*5 Normal, Expanded Image Processing Fine, Fast Reset Yes, No Lets you change the range of dark and bright areas in images. Displays the image signal. Lets you change the PQ curve of the dynamic range in the HDR PQ method. Lets you change the HLG curve of the dynamic range in the HDR HLG method. When set to Auto, the video level for the DVD input signal to the HDMI1 or HDMI2 ports is au-

tomatically detected and set. If you experience under or overexposure when set to Auto, set the video level of the projector to match that of the DVD/Blu-ray disc player's video level. Your player may be set to Normal

(Limited) or Expand (Full). Lets you change the EDID settings. Normal supports 3840 x 2160 30Hz signals, and Expanded supports 3840 x 2160 60 Hz signals. Improves the response speed for images projec-

ted at high-speed, such as games. Resets all Signal settings except for Diagonal Screen Size, 3D Viewing Notice, and Aspect.

*1 Only when an HDMI1, HDMI2, WirelessHD image signal is being input.

*2 Settings are saved for each type of input source or signal.

*3 EH-TW9400W/EH-TW9400 only.

*4 Only when a PC image signal is being input.

*5 Only when an HDMI1 or HDMI2 image signal is being input. Settings menu Function Keystone Blanking Keystone Menu/Settings

-60 to 60 Explanation Corrects keystone distortion. s p.31 Covers part of the image with a blank

(black screen). You can set the top, bottom, left, or right of the image. 75 Configuration Menu Function Menu/Settings HDMI Link Device Connections

-

HDMI Link On, Off Audio Out Device*

Power On Link AV System,WiHD Trans-

mitter (Optical), WiHD Transmitter (HDMI) Off, Bidirectional, Device -

> PJ, PJ -> Device Power Off Link On, Off Link Buffer On, Off WirelessHD*

Connected Device

-

WirelessHD On, Off Video Reception Reset Yes, No Explanation Displays a list of devices connected from the HDMI1 or HDMI2 ports, or from WirelessHD*. Enables or disables the HDMI Link function. Selects which device outputs audio. s p.61 Sets the link function when the power is turned on. When linking operations to the con-

nected device and turning on the projector, select Bidirectional or Device -> PJ. When linking power on for the pro-

jector to the connected device, se-

lect Bidirectional or PJ -> Device. Sets whether or not to power off con-

nected devices when the projector is turned off. If HDMI Link is not working correctly, you may be able to improve it by changing the settings. Displays the MAC address of Wire-

lessHD devices that can be connec-

ted. Enables or disables the WirelessHD function. Indicates the connection status with the WirelessHD Transmitter. While connected, Transmitter detected is displayed. Resets WirelessHD settings to their default settings. Note that even if you reset the pro-

jector, the WirelessHD Transmitter settings are not reset. 76 Configuration Menu Function Lock Setting Lens Lock Menu/Settings On, Off Child Lock On, Off Explanation is dis-

button when When set to On, the focus, zoom, and lens shift settings are locked at their current settings. If you press the Lens Lock is set to On, played on the screen. This locks the button on the pro-

jector's control panel to prevent chil-

dren from turning on the projector by accident. You can turn on the power when locked by holding down the button for approximately three seconds. You can still turn off the de-

button, or perform vice using the operations with the remote control as usual. If changed, this setting is enabled af-

ter you power off the projector and the cool-down process is complete. Note that even if Child Lock is set to On, the projector still turns on when the power cord is connected if Direct Power On is set to On. Control Panel Lock Full Lock, Partial Lock, Off Full Lock: Disables all of the projec-

tor's buttons. Partial Lock: Disables all of the pro-

jector's buttons except for the button. User Button Fine/Fast, 3D Display, Power Consumption, Info, WiHDVideo Rec...*

is displayed on the screen if but-

tons are pressed while the projector is locked. To unlock, press and hold the button on the control panel for at least 7 seconds. If changed, this setting is enabled once you close the Configuration menu. Select a Configuration menu item to button on the re-

assign to the mote control. By pressing the button, the assigned menu item se-

lection/adjustment screen is dis-

played, allowing you to make one-

touch settings/adjustments. 77 Configuration Menu Function Menu/Settings Explanation Memory Load Memory Memory1 to Memory10 Save Memory Memory1 to Memory10 Erase Memory Rename Memory Load Lens Position Memory1 to Memory10 Memory1 to Memory10, Default, DVD, VCR, SDTV, HDTV, Cinema, Sports, Music, Anime, Game, Cus-

tomized Memory1 to Memory10 Save Lens Position Memory1 to Memory10 Erase Lens Position Rename Lens Position Memory1 to Memory10 Memory1 to Memory10 Reset Yes, No

* EH-TW9400W/EH-TW8400W only. Extended menu Function Home Screen Home Screen Auto Disp. Menu/Settings On, Off Power Consumption, Auto Iris, Key-

stone, Info Custom Func-

tion 1 Custom Func-

tion 2 Loads the settings saved in Save Memory to adjust the image. Saves the settings made in Image to a memory. Erases a saved memory. Changes the saved memory name. Loads the settings created in Save Lens Position allowing you to adjust the lens position. Registers the adjustment values for zoom, focus, lens shift, and blanking that were created using the lens ad-

justment function as the lens posi-

tion. Erases the registered lens position. Changes the name registered for the lens position. Resets all Settings except for Audio Out Device, Power On Link, Power Off Link, Link Buffer, User Button, and Memory. Explanation Selects whether or not to display the Home screen automatically when the projector turns on. The Home screen is not displayed when the selected source has an image signal when the projector turns on. Select the function assigned to the Home screen. 78 Configuration Menu Function Menu/Settings Explanation Sets the position where the menu should be displayed. Sets whether or not to display the fol-

lowing messages (On or Off). Item names for image signals, color modes, and aspect ratios. If the internal temperature is rising when no image signal is being input or an unsupported signal is detec-

ted. Selects the screen status when no im-

age signal is being input. Sets whether or not to show a startup screen when projection begins (On or Off). If changed, this setting is enabled after you power off the projector and the cool-down process is complete. Sets whether or not to display a stand-

by confirmation message (On or Off). s p.27 s p.81 There are eight levels from white, through gray, and up to black. You can adjust each level individually. Starts making Color Uniformity ad-

justments. Resets all adjustments and settings for Color Uniformity to their default values. Change this setting depending on how the projector is installed. On, Off Enables or disables Color Uniformity. Display Menu Position

-

Messages On, Off Black, Blue, Logo Display Back-

ground Startup Screen On, Off Standby Con-

firmation On, Off Panel Align-

ment Color Uniformi-

ty

-

Color Uni-

formity Adjustment Level Start Adjust-

ments Reset Red, Green, Blue Yes, No Projection Front, Front/Ceiling, Rear, Rear/Ceiling 79 Configuration Menu Function Operation Direct Power On Menu/Settings On, Off Sleep Mode On, Off Sleep Mode Timer Illumination 1 to 30 On, Off Trigger Out Off, Power, Anamorphic Wide*1 On, Off*2 High Altitude Mode On, Off Standby Mode Communication Off, Communication On 80 Explanation You can set up the projector so that projection starts as soon as the power cord is plugged in without any button operations. Note that when this is set to On, pro-

jection starts if power is restored after a blackout or other power outage and the power cord is still plugged into the projector. If the set time is exceeded and no sig-

nal is input, the projector is automat-

ically turned off and enters standby mode. When in standby mode, press the button on the remote control or the button on the control pan-

el to start projection. Sets the interval for Sleep Mode. Set this to Off if the light from the in-

dicators on the control panel bother you when watching a movie in a dark room. When set to Off, the WiHD transmitter indicator also turns off while standing by. Set the Trigger Out function to com-

municate the projector's power on status and so on to external devices. When set to Off, no voltage is output from the Trigger Out port. When set to On or Power, voltage is output from the Trigger Out port when the projector is on. If you change this setting, the new setting will take effect the next time you turn the projector on. For Anamorphic Wide, when the projector is on and Aspect is set to Anamorphic Wide or Horiz. Squeeze, voltage is output from the Trigger Out port. If you change this setting, the new setting will take effect the next time you turn the projector on. Set this to On if you are using the pro-

jector above an altitude of 1500 me-

ters. Communication On indicates that the projector can be monitored over a network when the projector is in standby mode. Menu/Settings Explanation Configuration Menu Function Language Reset

-

Yes, No

*1 EH-TW9400W/EH-TW9400 only.

*2 EH-TW8400W/EH-TW8400 only. Panel Alignment menu Panel Alignment Menu/Settings Panel Alignment On, Off Select Color Pattern Color R, B R/G/B, R/G, G/B Start Adjust-

ments Memory

-

Load Panel Alignment Save Panel Alignment Erase Panel Alignment Rename Panel Alignment Memory1, Memory2, Memory3 Memory1, Memory2, Memory3 Memory1, Memory2, Memory3 Memory1, Memory2, Memory3 Selects the display language. Resets all Extended settings except for Memory, Projection, High Alti-

tude Mode, Standby Mode, and Language. Explanation Enables or disables Panel Alignment. Select the color to correct. Select the pattern used for correc-

tion. Starts Panel Alignment. s p.106 Loads settings saved using the Save Panel Alignment function. Saves the settings made in Panel Alignment to a memory. Erases memories registered using the Panel Alignment function. Renames Panel Alignment memo-

ries. Reset Yes, No Resets the correction value. 81 Configuration Menu Network menu Function Menu/Settings Explanation Wireless LAN Power On, Off Net. Info. - Wireless LAN

-

Net. Info. - Wired LAN Display the QR Code Network Configuration

-

-

-

Sets whether or not to use a Wireless LAN Power (On or Off). Displays the following network settings. Connection Mode Wireless LAN system Antenna Level Projector Name SSID DHCP IP Address Subnet Mask Gateway Address MAC Address Region Code Displays the following network setting status informa-

tion. Projector Name DHCP IP Address Subnet Mask Gateway Address MAC Address Displays network information for the projector with a QR code. Displays the screen to set the network. s p.83 Notes on operating the Network menu Basic operations are made in the same way as when using the Configuration menu. However, be sure to select the Complete menu to save your settings when done. Yes:

No:

Cancel:

Saves the settings and exits the Network menu. Exits the Network menu without saving the settings. Continues displaying the Network menu. 82 Configuration Menu Soft Keyboard Operations In the Network menu, the soft keyboard appears when you need to enter numbers and characters. Press the buttons on the control panel to select keys, button to input them. Press Finish to confirm your input, or Cancel to cancel your buttons on the remote control or the and then press the input. CAPS key:

SYM1/2 key:

Basic menu Switches between uppercase and lowercase letters. Switches the symbol keys. Function Projector Name PJLink Password Remote Password Display LAN Info. Menu/Settings Up to 16 alphanumeric characters Up to 32 alphanumeric characters Up to 8 alphanumeric characters Text & QR Code, Text Wireless LAN menu Function Menu/Settings Connection Mode Quick, Advanced Channel SSID 1ch, 6ch, 11ch Up to 32 alphanumeric characters Explanation Enter a name to identify the projector over a network. Set a password to use when you control the projector using compatible PJLink software. s p.110 Set a password to use when you operate the projector from a smartphone or a tablet. Set the display format for the projector's network information. Explanation Determines how the wireless LAN is connected. Quick: Using Epson iProjection allows you to connect to smartphones, tablets, or computers directly using wireless communication. The projector becomes a simple access point. (Make sure the number of devices connected to the projector is six or less.) It may take longer to update the pro-

jected image if the number of connected devices exceeds this number. Advanced: Lets you connect to multiple smartphones, tab-

lets, or computers over a wireless network access point.

(This can only be set when Connection Mode is set to Quick.) Select the frequency bandwidth used by the wireless LAN.

(This can only be set when Connection Mode is set to Ad-

vanced.) Enter an SSID. When an SSID is provided for the wireless LAN system in which the projector participates, enter the SSID. 83 Configuration Menu Function Menu/Settings Search Access Point To Search View IP Settings

(This can only be set when Connection Mode is set to Ad-

vanced.) DHCP IP Address Subnet Mask Gateway Address SSID Display On, Off IP Address Display On, Off Explanation

(This can only be selected when Connection Mode is set to Advanced.) Search for available wireless network access points. indicates currently connected access points. indicates the access points where security is set. If you select an access point which has security, Security menu appears. s p.84 Sets whether or not to use DHCP (On or Off). If this is set to On, you cannot set any more addresses. Inputs the IP address for the projector. The following IP addresses cannot be used. 0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255) Inputs the subnet mask for the projector. The following subnet masks cannot be used. 0.0.0.0, 255.255.255.255 Inputs the gateway IP address of the projector. The following gateway addresses cannot be used. 0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255) Sets whether or not to display the SSID on the LAN Standby screen and the Home screen (On or Off). Sets whether or not to display the IP address on the LAN Standby screen and the Home screen (On or Off). Security menu Function Security Passphrase Wired LAN menu Menu/Settings No, WPA2-PSK, WPA/

WPA2-PSK From 8 to 32 single-

byte alphanumeric characters Explanation Sets the security. In Quick, WPA2-PSK is selectable. In Advanced, WPA2-

PSK/WPA/WPA2-PSK is selectable. Inputs the passphrase. It is recommended to change the passphrase periodically for the purpose of security. Function Menu/Settings Explanation DHCP On, Off IP Address Number from 0 to 255 Set whether or not (On/Off) to use DHCP. If this is set to On, you cannot set any more addresses. Enter the IP address assigned to the projector. You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used. 0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255

(where x is a number from 0 to 255) 84 Configuration Menu Function Subnet Mask Menu/Settings Number from 0 to 255 Gateway Address 0 to 255 characters IP Address Display On, Off Others menu Explanation Enter the projector's subnet mask. You can enter a number from 0 to 255 in each field of the address. However, the following sub-

net masks cannot be used. 0.0.0.0, 255.255.255.255 Enter the projector's gateway IP address. You can enter a number from 0 to 255 in each field of the address. However, the following gate-

way addresses cannot be used. 0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255

(where x is a number from 0 to 255) Set to Off to prevent the IP address from being displayed on the Net. Info. - Wired LAN screen. Function Menu/Settings Explanation PJLink Notification On, Off Notified IP Address Number from 0 to 255 AMX Device Dis-

covery On, Off Control4 SDDP On, Off To use the notification function of PJLink, select On. Enter the IP address of a computer to be notified of the projectors operating status using the PJLink notification function. You can enter numbers from 0 to 255. The fol-

lowing IP addresses cannot be used. 127.x.x.x, 224.0.0.0 to 255.255.255.255 (x is a number from 0 to 255) When you want to allow the projector to be de-

tected by AMX Device Discovery, set this to On. Set this to Off if you are not connected to an en-

vironment controlled by a controller from AMX or AMX Device Discovery. When you want to allow the projector to be de-

tected by Control4 SDDP, set this to On. Set this to Off if you are not connected to an environ-

ment controlled by a controller from Control4 or Control4 SDDP. Reset menu Function Explanation Reset network settings. You can reset all adjustment values for Network to their default settings. 85 Configuration Menu Info menu Function Projector Info Version Reset menu Function Reset Lamp Hours Reset Memory Reset Lens Position Reset All Config Menu/Settings Explanation Lamp Hours Source Input Signal Resolution Scan Mode Refresh Rate 3D Format Sync Info Color Depth Color Format Status Serial Number Event ID Main Video2 Displays the cumulative lamp operating time. Displays the current input source. Displays the input signal setting of the current input source. Displays the resolution. Displays the scan mode. Displays the refresh rate. Displays the 3D format of the signal input during 3D projec-

tion (Frame Packing, Side by Side, or Top and Bottom). Displays the image signal information. This information may be needed if service is required. Displays the color depth and color difference. Displays information on the color space and dynamic range. This is information about errors that have occurred on the projector. This information may be needed if service is required. Displays the projector's serial number. The application error log appears. s p.98 Displays the firmware version of the projector. Explanation Resets the cumulative lamp hours use time to 0 H. Reset when you replace the lamp. Resets all items for Memory to their default settings. Resets all settings saved using the Save Lens Position function. Resets all items in the Configuration menu to their default settings. The following adjustment values are not reset to their defaults: Memory, Panel Alignment, Color Uniformity, Lamp Hours, Language, and Network Settings. 86 Troubleshooting Problem Solving Reading the Indicators You can check the status of the projector from the flashing and lit

,

, o and m on the control panel. Refer to the following table to check the projector's status and how to remedy problems shown by the indicators. Indicator status during an error/warning Indicators Status Replace Lamp

: Lit

: Flashing

: Status maintained

: Off Remedy It is time to replace your lamp. Replace the lamp with a new lamp as soon as possible. s p.103 The lamp may explode if you continue to use it in this status.

(blue)/(orange)

(blue)/(orange) High Temp Warning You can continue projecting. If the temperature rises too high again, projection stops automatically. If the projector is installed next to a wall, make sure there is at least 20 cm between the wall and the projector's exhaust vent. If the air filter is clogged, clean it. s p.100 Make sure that nothing is blocking the area around the inlet and that the temperature around the inlet is not too high. s p.116 87 Troubleshooting Indicators Status Internal Error

(blue)/(orange)

(blue)/(orange)

(blue)/(orange)

(blue)/(orange)

(blue)/(orange) Fan Error Sensor Error Cinema Filter Error Auto Iris Error Power Err. (Ballast) Lamp Error Lamp Failure High Temp Error

(Overheating)

(blue)/(orange) Remedy The projector has malfunctioned. Remove the power plug from the electrical outlet, and contact your local dealer or the nearest Epson repair center. s Epson Projector Contact List There is a problem with the lamp, or it failed to turn on. Disconnect the power cord, and then check if the lamp is cracked. s p.103 If it is not cracked, reinstall the lamp and turn on the power. If reinstalling the lamp does not fix the problem, or if the lamp is cracked, remove the power plug from the electrical outlet, and contact your local dealer or the nearest Epson repair center. s Epson Projector Contact List Check that the lamp cover has been properly closed. If the air filter is clogged, clean it. s p.100 When using at an altitude of 1500 m or more, set High Altitude Mode to On. s Extended - Operation - High Altitude Mode p.78 The internal temperature is too high. The lamp turns off automatically and projection stops. Wait for about five minutes. When the fan has stopped, disconnect the power cord. If the projector is installed next to a wall, make sure there is at least 20 cm between the wall and the projector's exhaust vent. If the air filter is clogged, clean it. s p.100 Make sure that nothing is blocking the area around the inlet and that the temperature around the inlet is not too high. s p.116 If turning the power back on does not clear the problem, stop using the projector and remove the power plug from the elec-

trical outlet. Contact your local dealer or the nearest Epson re-

pair center. s Epson Projector Contact List 88 Troubleshooting Indicator status during normal operation Indicators Status Standby condition

: Lit

: Flashing

: Off Remedy When you press the button on the remote control, or the button on the control panel, projection starts after a short wait. Warm-up in progress Warm-up time is about 30 seconds. The power-off operation is disabled while the projector is warm-

ing-up. All operations are disabled while the projector is cooling-down. The projector enters standby condition when cool-down is com-

plete. If for any reason the power cord is disconnected during cool-down, wait until the lamp has cooled down sufficiently

(about 10 minutes), reconnect the power cord, and then press the button on the control panel. The projector is operating normally. button on the remote control, or the

(blue) Cool-down in pro-

gress Projection in pro-

gress

(blue) c Under normal operating conditions, the o and m indicators are off. When the Illumination function is set to Off, all indicators are off under normal projection conditions. s Extended - Operation - Illumination p.78 When the Indicators Provide No Help Check the problem Check the following table to see if your problem is mentioned, and go to the appropriate page for information on handling the problem. 89 Troubleshooting Problems relating to im-

ages Problems when projection starts Problems with the remote control Problems with the control panel Problems with 3D Problems with HDMI Problem No images appear. Projection does not start, the projection area is completely black, or the projection area is completely blue. Moving images being projected from a computer are not projected.

"Not supported" is displayed

"No Signal " is displayed Images are fuzzy or out of focus. Interference or distortion appears in the images. The image is truncated (large) or small, or only a part of the image is projected. Image colors are not right. The whole image appears purplish or greenish, images are black &

white, or colors appear dull.*

Images appear dark. Projection stops automatically. The projector does not turn on. The remote control does not respond. Cannot make settings on the control panel. Cannot project correctly in 3D. HDMI Link does not function. The device name is not displayed under device connections. Problems with WirelessHD "Transmitter not found." is displayed Cannot project WirelessHD images. Interference, distortion, or interruption appear in WirelessHD. Half of the image on the left or right stops projecting or the image is doubled up. Cannot access the network via wireless LAN. The image contains static during network projection. Network problems Page p.90 p.91 p.91 p.91 p.92 p.92 p.92 p.93 p.93 p.93 p.94 p.94 p.94 p.95 p.95 p.96 p.96 p.96 p.97 p.97 p.98 p.98

* Because color reproduction differs between monitors and computer LCD screens, the image projected by the projector and the color tones displayed on the monitor may not match, however this is not a fault. Problems relating to images No images appear Check Is the projector turned on?

Is the power cord connected?

Remedy button on the remote control or the Press the on the control panel. Connect the power cord. button 90 Troubleshooting Check Are the indicators switched off?

Is an image signal being input?

Remedy Disconnect and then reconnect the projector's power cord. Check that pressing the power button after connection supplies the projector with power. Check that the connected device is turned on. When Messag-

es is set to On from the Configuration menu, image signal mes-

sages are displayed.s Extended - Display - Messages p.78 Are the Configuration menu settings correct? Reset all of the settings. s Reset - Reset All Config p.86

(Only when projecting computer image sig-

nals) Was the connection made while the power of the projector or the computer was already turned on?

If the connection is made while the power is already turned on, the Fn key (Function key) that changes the computer's image signal to external output may not work. Turn off the power for the computer and the projector and then turn it back on again. Moving images are not displayed Check Remedy

(Only when projecting computer image sig-

nals) Is the computer's image signal set to external output and to output to the LCD monitor at the same time?

Depending on the computer's specifications, moving images may not be displayed when the computer is set to external out-

put and to the LCD monitor output at the same time. Change it so that the image signal is set to external output only. For the computer's specifications, see the documentation sup-

plied with the computer.

"Not supported" is displayed Check Remedy

(Only when projecting computer image sig-

nals) Do the image signal's frequency and resolu-

tion correspond to the mode?

Check the image signal being input in Resolution from the Con-

figuration menu, and check that it corresponds to the projector's resolution. sInfo - Projector Info p.86 s p.112

"No Signal " is displayed Check Are the cables connected correctly?

Is the correct image input port selected?

Is the connected device turned on?

Remedy Check that all the cables required for projection are securely connected. s p.19 Change the image with the source buttons on the remote con-

trol, or the Turn on the device. button on the control panel. s p.26 91 Troubleshooting Check Remedy

(Only when projecting computer image sig-

nals) Are the image signals being output to the projector?

Images are fuzzy or out of focus Check Has the focus been adjusted?

Is the projector at the correct distance?

Has condensation formed on the lens?

Change it so that the image signal is set to external output, and not just the computer's LCD monitor. For some models, when the image signals are output externally, they no longer appear on the LCD monitor. For the computer's specifications, see the documentation sup-

plied with the computer. If the connection is made while the power of the projector or the computer is already turned on, the Fn key (Function key) that changes the computer's image signal to external output may not work. Turn the power for the computer and the projector off and then back on again. Remedy Adjust the focus. s p.29 Check the recommended projection range. s p.16 If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the projector up in the room about one hour before it is used. If the projector is wet from condensation, turn off the projector, disconnect the power cord, and leave it for a while. Interference or distortion appear in images Check Are the cables connected correctly?

Is an extension cable being used?

(Only when projecting computer image sig-

nals) Are the Sync. and Tracking settings adjusted correctly?

(Only when projecting computer image sig-

nals) Is the correct resolution selected?

Remedy Check that all the cables required for projection are securely connected. s p.19 If an extension cable is used, electrical interference may affect the signals. The projector uses automatic adjustment functions to project at the optimum status. However, depending on the signal, some may not be adjusted correctly even after performing self correc-

tions. If this happens, adjust the Tracking and Sync. settings from the Configuration menu. s Signal - Tracking/Sync. p.74 Set the computer so that the signals being output are compatible with the projector. s p.112 Part of the image is truncated (large) or small Check Is the correct Aspect selected?

Is the image Position adjusted correctly?

Remedy Select the aspect mode to match the input signal in Aspect from the Configuration menu. s Signal - Aspect p.74 Adjust the Position setting from the Configuration menu. s Signal - Position p.74 92 Troubleshooting Check Remedy

(Only when projecting computer image sig-

nals) Is the correct resolution selected?

Set the computer so that the signals being output are compatible with the projector. s p.112 Image colors are not right Check Are the cables connected correctly?

Is the contrast adjusted correctly?

Is the color adjusted correctly?

(Only when projecting images from a video device) Are the color saturation and tint adjusted cor-

rectly?

Images appear dark Check Is the image brightness set correctly?

Is the contrast adjusted correctly?

Is it time to replace the lamp?

Projection stops automatically Check Is Sleep Mode enabled?

Remedy Check that all the cables required for projection are securely connected.s p.19 For the PC port, make sure the connector is the same color as the cable port. s p.20 Adjust the Contrast setting from the Configuration menu. s Image - Contrast p.72 Adjust the Advanced setting from the Configuration menu. s Image - Advanced p.72 Adjust the Color Saturation and Tint settings from the Config-

uration menu. sImage - Color Saturation/Tint p.72 Remedy Adjust the Brightness setting from the Configuration menu. s Image - Brightness p.72 Adjust the Contrast setting from the Configuration menu. s Image - Contrast p.72 When the lamp is nearly ready for replacement, the images be-

come darker and the color quality becomes poorer. When this happens, replace the lamp with a new lamp. s p.103 Remedy If the set time is exceeded and no signal is input, the lamp is automatically turned off and the projector enters standby mode. The projector returns from standby status when you press the button on the remote control or the button on the con-

trol panel. If you want to disable Sleep Mode, change the setting to Off.s Extended - Operation - Sleep Mode p.78 93 Troubleshooting Problems when projection starts The projector does not turn on Check Is the power turned on?

Is Child Lock set to On?

Do the indicators turn on and off when the power cord is touched?

Are the lamp cover and lamps installed cor-

rectly?

Problems with the remote control The remote control does not respond Remedy button button on the remote control or the button on the control panel for approximately Press the on the control panel. When Child Lock is set to On from the Configuration menu, hold down the three seconds, or perform operations from the remote con-

trol.s Settings - Lock Setting - Child Lock p.75 Turn off the projector, and then disconnect and reconnect the projector's power cord. If the problem continues, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest projector information center. s Epson Projector Contact List If the lamp or lamp cover is installed incorrectly, the projector cannot be turned on. Check how it is installed. s p.103 Check Remedy Is the remote control light-emitting area pointing towards the remote receiver on the projector during operation?

Is the remote control too far from the projec-

tor?

Is direct sunlight or strong light from fluores-

cent lamps shining onto the remote receiver?

Are the batteries dead or have the batteries been inserted correctly?

Is the remote control pointed at the Wire-

lessHD Transmitter when operating the Wire-

lessHD Transmitter control button? (EH-

TW9400W/EH-TW8400W only) Problems with the control panel Point the remote control towards the remote receiver. Also, check the operating range. s p.24 Check the operating range. s p.24 Set the projector up in a location where strong light does not shine onto the remote receiver. Make sure the batteries are inserted correctly or replace the bat-

teries with new ones if necessary. s p.23 Make sure you point the remote control at the WirelessHD Trans-

mitter when using the WirelessHD Transmitter control button on the remote control. s p.58 Cannot make settings on the control panel Check Remedy Is Control Panel Lock set to Full Lock or Par-

tial Lock?

When Control Panel Lock is set to Full Lock in the Configura-

tion menu, all button operations on the control panel are disa-

bled; when Partial Lock is set, only the button on the control panel is available. Perform operations from the remote control. s Settings - Lock Setting - Control Panel Lock p.75 94 Troubleshooting Problems with 3D Cannot project correctly in 3D Check Are the 3D Glasses turned on?

Are the 3D Glasses fully charged?

Is a 3D image being projected?

Is the input image in 3D?

Is 3D Display set to 2D?

Is 3D Format set correctly?

Are you viewing within the reception range?

Has pairing been performed correctly?

Are there any devices that cause radio wave interference in the vicinity?

Problems with HDMI HDMI Link does not function Remedy Turn on the 3D Glasses. Charge the 3D Glasses. If the projector is projecting a 2D image, or if an error occurs on the projector that prevents the 3D image from being projected, you cannot view 3D images even if you are wearing the 3D Glasses. Check that the input image is 3D compatible. Since most TV broadcasts do not contain a 3D format signal, 3D reception must be set manually. If 3D Display is set to 2D from the Configuration menu, the pro-

jector does not automatically change to 3D even when a 3D im-

age is input. Set 3D Display to either 3D or Auto.s Signal - 3D Setup - 3D Display p.74 Unless the 3D format of the AV device and 3D Format of the projector are the same, part of the image may not be displayed. Check that the projector's 3D Format setting matches the 3D format setting for the AV device. s Signal - 3D Setup - 3D For-

mat p.74 When changing the 3D Format, set 3D Display to 3D, and then press the If the distance between the projector and the 3D Glasses exceed 10 m, the connection may be lost. Move the 3D Glasses closer to the projector. See the user's guide supplied with your 3D Glasses and perform pairing. When using other devices at the same time with the frequency band (2.4 GHz) such as Bluetooth communication devices, wire-

less LAN (IEEE802.11b/g), or microwave ovens, radio wave inter-

ference may occur, the image may be interrupted, or communi-

cation may not be possible. Do not use the projector near these devices. button. Check Remedy Are you using a cable that meets the HDMI standards?

Operations are not possible with cables that do not meet the HDMI standards. 95 Troubleshooting Check Remedy Does the connected device meet the HDMI CEC standards?

Are the cables connected correctly?

Is the power for the amplifier or DVD recorder and so on turned on?

Was a new device connected, or was the con-

nection changed?

Are many multi-media players connected?

button, and then check if the device is If the connected device does not meet the HDMI CEC standards, it cannot be operated even if it is connected to the HDMI port. See the documentation and so on supplied with the connected device for more information. Also, press the available under Device Connections. s p.62 Check that all the cables required to use HDMI Link are securely connected. s p.61 Put each device in standby status. See the documentation and so on supplied with the connected device for more information. If you have connected a speaker and so on, set the connected equipment to PCM output. If the CEC function for a connected device needs to be set again, for example when a new device is connected or the connection is changed, you may need to restart the device. Up to 3 multi-media players that meet the HDMI CEC standards can be connected at the same time. The device name is not displayed under Device Connections Check Remedy Does the connected device meet the HDMI CEC standards?

If the connected device does not meet the HDMI CEC standards, it is not displayed. See the documentation and so on supplied with the connected device for more information. Problems with WirelessHD (EH-TW9400W/EH-TW8400W only)

"Transmitter not found." is displayed Check Remedy Is the power switch on the side of WirelessHD Transmitter turned on?

Check the power lamp on the WirelessHD Transmitter. If there is no power being supplied, make sure the connector for the AC adapter is securely connected, and then turn on the power switch. It may take a while to receive signal. Cannot project WirelessHD images Check Remedy Does the cable connecting the supplied Wire-

lessHD Transmitter meet the HDMI stand-

ards?

Is WirelessHD set to Off?

Are signals being received within the Wire-

lessHD transmission range?

If the cable does not meet the HDMI standards, operations are not possible. When WirelessHD is set to Off from the Configuration menu, projection is not possible for WirelessHD input signals. Set Wire-

button.s Settings - Wire-

lessHD to On and press the lessHD - WirelessHD p.75 Check the range within which the WirelessHD's transceiver can communicate, and view within that range. s p.57 96 Troubleshooting Check Remedy Is the power switch on the side of the supplied WirelessHD Transmitter turned on?

Is the WirelessHD indicator for the supplied WirelessHD Transmitter off?

Is the Link indicator for the supplied Wire-

lessHD Transmitter off?

Are the projector and the WirelessHD Trans-

mitter facing the correct way?

Check the power lamp on the WirelessHD Transmitter. If there is no power being supplied, make sure the connector for the AC adapter is securely connected, and then turn on the power switch. The WirelessHD cannot communicate with the projector. Check the range within which the WirelessHD's transceiver can com-

municate, and setup within that range. No signal is output from the AV device connected to the Wire-

lessHD Transmitter. Check that the cables from the AV device and the WirelessHD Transmitter are securely connected. Setup the projector and the WirelessHD Transmitter so that they are facing each other. Interference, distortion, or interruption appear in WirelessHD Check Remedy Are signals being received within the Wire-

lessHD transmission range?

Are there any obstructions between the Wire-

lessHD Transmitter and the projector?

Is the reception too low?

Check the range within which the WirelessHD's transceiver can communicate, and view within that range. s p.57 Because WirelessHD communicates using a tight beamed elec-

tromagnetic wave, if there are any people or objects and so on obstructing the communication path, this could have an adverse affect on the image. Make sure that there are no obstacles be-

tween the WirelessHD Transmitter and the projector within the WirelessHD transmission range. s p.57 If the transmissions are not strong enough, communication may be unstable. Check Video Reception as you set up the transmitter as it is sometimes possible to improve the strength of the transmission by moving the WirelessHD Transmitter or changing its direc-

tion.s Settings - WirelessHD - Video Reception p.75 Transmission strength may differ depending on the surround-

ings, or they may be unstable. While checking Video Recep-

tion, set up the transmitter at a location where the displayed value stabilizes.s Settings - WirelessHD - Video Recep-

tion p.75 Half of the image on the left or right stops projecting or the image is doubled up Check Is the reception too low?

Remedy Check Video Reception as you set up the transmitter as it is sometimes possible to improve the strength of the transmission by moving the WirelessHD Transmitter or changing its direc-

tion.s Settings - WirelessHD - Video Reception p.75 97 Troubleshooting Network problems Cannot access the network via wireless LAN Check Is Wireless LAN Power set to Off?

Is the passphrase correct?

Have you checked the Event ID?

Remedy Set Wireless LAN Power to On in the Configuration menu. If this is already set to On, set Wireless LAN Power to Off, and then set it to On again. s Network - Wireless LAN Power p.82 Note that the passphrase is case sensitive; upper case and lower case letters are treated as different characters. If you have for-

gotten your passphrase, set a new one. s Network - Network Configuration - Security - Passphrase p.84 Check the Event ID number and perform the following steps. sInfo - Projector Info - Event ID p.86 s p.98 The settings cannot be modified using the remote controller function for Epson iProjection. Check Remedy Is the connected network device turned on? When the projector is in the standby mode with Standby Mode set to Communication On, check to see if the connected network device is powered on. After powering on the network device, try starting the projector again. s Extended-Standby Mode p.78 The image contains static during network projection Check Remedy Are there any obstacles between the access point and the connected device?

Is the distance between the access point and the connected device too far?

Are there any Bluetooth devices or micro-

wave oven in the vicinity?

Are too many devices connected?

Check for any obstacles between the access point, the mobile device, the computer, and the projector, and change their posi-

tions to improve communication. Make sure that the access point, the mobile device, the comput-

er, and the projector are not too far apart. Move them closer to-

gether and try to connect again. If the wireless connection is slow or your projected image con-

tains noise, check for interference from other equipment, such as a Bluetooth device or microwave. Move the interfering device farther away or expand your wireless bandwidth. Reduce the number of connected devices if the connection speed declines. About Event ID Check the event ID and perform the remedy given below. If you cannot resolve the problem, contact your local dealer or the nearest Epson repair center. s Epson Projector Contact List 98 Troubleshooting Event ID Cause Remedy Network communication is unstable. Check the network communication status, and reconnect after waiting for a while. Failed to start the network software. Restart the projector. An image that was transferred cannot be re-

produced. Communications was cut off from the comput-

er. The network software ended unexpectedly. A system error occurred in the projector. Restart the network software. Check the status of network communications. Wait for a while and then try connecting again. Restart the projector. The same SSID access point cannot be found. Set the computer, the access point, and the projector to the same SSID. WPA and WPA2 authentication type mismatch. Check the setting of wireless LAN security to see if it is correct. Check with the network administrator and fol-

low their instructions. Check that the DHCP server is operating cor-

rectly. Turn off the DHCP setting if you do not use DHCP.s Network - Network Configura-

tion - Wireless LAN - IP Settings - DHCP p.82 If restarting the projector or network software does not solve the problem, contact your local dealer or the nearest address provided in the Epson Projector Contact List. s Epson Projector Contact List 0022 0027 0028 0029 0030 0031 0035 0434 0481 0482 0485 0432 0435 0433 0484 04FE 0479 04FF 0891 0892 0894 0898 0020 0026 0032 0036 0037 0038 0899 Communications was cut off because a con-

nection was made to the wrong access point. Failed to acquire the DHCP. Other connection errors 99 Maintenance Maintenance Cleaning the Parts You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate. Warning Do not use sprays that contain flammable gas to remove dirt and dust from the projector's lens, air filter, and so on. The projector may catch fire due to the high internal temperature of the lamp. Use a vacuum or a manual air blower to remove dirt and dust attached to the lens and the air filter. Cleaning the air filter Clean the air filter if dust has accumulated on the air filter or when the following message is displayed.

"The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air filter."

Attention If dust collects on the air filter, it can cause the internal temperature of the projector to rise, and this can lead to problems with operation and shorten the optical engine's service life. It is recommended that you clean the air filter at least once every three months. Clean them more often than this if using the projector in a particularly dusty environment. Do not rinse the air filter in water. Do not use detergents or solvents. Lightly brush the air filter to clean it. If it is brushed too strongly, dust will be ground into the air filter and cannot be removed. Do not use an air duster. Combustible material may remain, and dust may enter the precision parts. c Remove the air filter. Grip the knob in the center of the air filter and pull it out. a Press the button on the remote button on the control or the control panel to turn off the power, and then disconnect the power cord. b Remove the air filter cover. Hook your finger into the tab on the air filter cover, and remove it from the lens side. 100 Maintenance d Hold the air filter with the surface facing down and tap it 4 or 5 times to remove the dust. Turn it over and tap the other side in the same way. f Install the air filter. Grip the air filter by the knob in the center and insert it at an angle. g Install the air filter cover. Secure the tab on the outside first, and then secure the tab on the lens side. Attention If the air filter is hit too hard, it may become unusable due to deformities and cracks. e Remove any dust remaining on the air filter by using a vacuum cleaner from the front side. Cleaning the main unit Before cleaning, make sure you unplug the charging adapter from the outlet. Clean the projector's surface by wiping it gently with a soft cloth. If it is particularly dirty, use a piece of well-wrung cloth moistened with water and wipe the surface again with a dry cloth. Attention Do not use detergent for kitchen or volatile substances such as wax, benzine and thinner to clean the projector's surface. The quality of the outer case may change or the paint may peel off. 101 Maintenance Cleaning the lens Before cleaning, make sure you unplug the charging adapter from the outlet. After manually opening the lens shutter, carefully wipe away any dirt on the lens with a cloth for cleaning glasses and so on. After cleaning, close the lens shutter. Attention Do not rub the lens with harsh materials or handle the lens too roughly as it can easily become damaged. Do not use an air duster. Combustible material may remain, and dust may enter the precision parts. Replacement Periods for Consumables Air filter replacement period If the message is displayed even though the air filter has been cleaned s p.100 Lamp replacement period The following message is displayed when projection starts:

"It is time to replace your lamp. Please contact your Epson projector reseller or visit www.epson.com to purchase."

The projected image gets darker or starts to deteriorate. c The lamp replacement message is set to appear after 3400 H in order to maintain the initial brightness and quality of the projected images. The message display time changes depending on the usage situation, such as the color mode setting and so on. If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode increases. When the lamp replacement message appears, replace the lamp with a new one as soon as possible, even if it is still working. Depending on the characteristics of the lamp and the way it has been used, the lamp may become darker or stop working before the lamp warning message appears. You should always have a spare lamp unit ready in case it is needed. Replacing Consumables Replacing the air filter c Dispose of used air filters properly in accordance with your local regulations. Filter frame: Polypropylene Filter: Polypropylene a Press the button on the remote button on the control or the control panel to turn off the power, and then disconnect the power cord. 102 Maintenance b Remove the air filter cover. Hook your finger into the tab on the air filter cover, and remove it from the lens side. d Install the new air filter. Grip the air filter by the knob in the center and insert it at an angle. c Remove the old air filter. Grip the knob in the center of the air filter and pull it out. e Install the air filter cover. Secure the tab on the outside first, and then secure the tab on the lens side. Replacing the lamp Warning When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. If replacing the lamp of a projector that has been suspended from the ceiling, you should always assume that the lamp is cracked, and remove the lamp cover with care. When you open the lamp cover, small shards of glass could fall out. If any shards of glass get into your eyes or mouth, contact a doctor immediately. 103 Maintenance Caution Do not touch the lamp cover immediately after turning off the projector as it is still hot. Wait until the lamp has cooled down sufficiently before removing the lamp cover. Otherwise, you could get burnt. We recommend the use of genuine EPSON option lamps. The use of non-genuine lamps may affect projection quality and safety. Any damage or malfunction caused by the use of non-genuine lamps may not be covered by Epson's warranty. e Remove the old lamp. Raise the handle on the lamp, and then pull it straight up. f Install the new lamp. Insert the lamp in the correct direction, and then lower the handle. g Tighten the two lamp fixing screws. a Press the button on the remote button on the control or the control panel to turn off the power, and then disconnect the power cord. b Loosen the lamp cover fixing screw. c Remove the lamp cover. Slide the lamp cover straight forward and remove it. d Loosen the two lamp fixing screws. 104 Maintenance h Replace the lamp cover. Slide the cover back into place. i Tighten the lamp cover fixing screw. Warning Do not disassemble or remodel the lamp. If a modified or disassembled lamp is installed in the projector and used, it could cause a fire, electric shock, or an accident. Caution Make sure you install the lamp and lamp cover securely. If they are not installed correctly, the power does The lamp contains mercury (Hg). Dispose of used lamps in accordance with your local laws and regulations not turn on. on disposing of fluorescent tubing. Resetting lamp hours After replacing the lamp, make sure you reset the lamp hours. The projector records how long the lamp is turned on and a message and indicator notify you when it is time to replace the lamp. a Turn on the power. b Press the button. The Configuration menu is displayed. buttons to select Yes, button to d Use the and then press the execute. The lamp hours are reset. c Select Reset - Reset Lamp Hours. A reset confirmation message is displayed. 105 Maintenance Panel Alignment Adjusts the pixel color shift of the LCD display. You can adjust the pixels horizontally and vertically by 0.125 pixel within a range of 3 pixel. c Image quality may decline after performing LCD alignment. Images for pixels that extend beyond the edge of the projected screen are not displayed. a Press the button while projecting, and then select Display from Extended. b Select Panel Alignment, and then press the button. c Enable Panel Alignment.

(1)

(2)

(3) button. Select Panel Alignment, and then press the Select On, and then press the ton. Press the previous screen. button to return to the but-

d Select the color you want to adjust. Select Select Color, and then press the

(1) button.

(2)

(3) Select R (red) or B (blue), and then press the Press the previous screen. button. button to return to the e Select the grid color displayed when making adjustments from Pattern Color.

(1) button. Select Pattern Color, and then press the Select a combination of R (red), G

(green), and B (blue) for the grid color. R/G/B: Displays a combination all three colors; red, green and blue. The actual color of the grid is white. R/G: This is available when R is selected from Select Color. Displays a combi-

nation of two colors; red and green. The actual color of the grid is yellow. G/B: This is available when B is selected from Select Color. Displays a combi-

nation of two colors; green and blue. The actual color of the grid is cyan. Press the previous screen. button to return to the

(2)

(3) 106 Maintenance f Select Start Adjustments, and then button. press the First, select Shift the whole panel and adjust the entire LCD display. When a confirmation message is displayed, press the button to .start the adjustment. c The image may become distorted while adjusting. The image is restored once adjustments are complete. i Use the

,

,

, and buttons to make adjustments, and then press the the next adjustment point. button to move to j When you have adjusted all four corners, select Exit, and then press the button. g Use the adjust and then press the buttons to button. h To make more detailed adjustments, select the Adjust the four corners and then press the confirm. button to If you feel you still need to make adjustments after correcting all four points, select Select intersection and adjust and then continue making adjustments. 107 Maintenance Color Uniformity If colors in the projected image are uneven, you can adjust the color tone of the whole image in Color Uniformity. c The color tone may not be uniform even after performing color uniformity. a Press the button while projecting, and then select Display from Extended. b Select Color Uniformity, and then press the The following screen is displayed. button. e Select Adjustment Level, and then press the button. f Use the adjustment level. buttons to set the g Press the previous screen. button to return to the h Select Start Adjustments, and then press the button. i Select the area you want to adjust, and then press the Adjust the outer areas first, and then adjust the whole screen. button. Color Uniformity: Turns color uniformity on or off. Adjustment Level: There are eight levels from white, through gray, and up to black. You can adjust each level individually. Start Adjustments: Starts making color uniformity adjustments. Reset: Resets all adjustments and settings for Color Uniformity to their default values. c The image may become distorted while adjusting Color Uniformity. The image is restored once adjustments are complete. c Select Color Uniformity, and then press the button. d Set this to On, and then press the button. 108 Maintenance j Use the buttons to select the color you want to adjust, buttons to and then use the adjust. Press the tone. Press the the color tone. button to weaken the color button to strengthen k Return to step 5 and adjust each level. l To complete the adjustment, press the button. 109

 

 

Model: H928A,H930A,H931A User's Guide EH-TW9400 EH-TW8400W EH-TW8400 Pro Cinema 6050UB Home Cinema 5050UBe Home Cinema 5050UB LCD Projector Organization of the Guide and Notations in the Guide Using Each Guide The guides for this projector are organized as shown below. Safety Instructions/Support and Service Guide Contains information on using the projector safely, as well as a support and service guide, troubleshooting check lists, and so on. Make sure you read this guide before using the pro-

jector. User's Guide (this guide) Contains information on setting up and basic operations before using the projector, using the Configuration menu, and handling problems and performing routine maintenance. WirelessHD Transmitter User's Guide (H931A/EH-TW8400W/Home Cinema 5050UBe only) Contains information on handling the WirelessHD Transmitter and warnings and so on. Quick Start Guide Contains information on the procedures for setting up the projector. Read this first. 1 Organization of the Guide and Notations in the Guide Notations Used in This Guide Safety Indications The documentation and the projector use graphical symbols to show how to use the projector safely. The following shows the symbols and their meanings. Please understand and respect these caution symbols in order to avoid injury to persons or property. Warning This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling. Caution This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling. General Information Indications Attention Indicates procedures which may result in damage or malfunctions to occur. c Indicates additional information and points which may be useful to know regarding a topic. s Menu Name Button Name Indicates a page where detailed information regarding a topic can be found. Indicates Configuration menu items. Example: Image - Color Mode Indicates the buttons on the remote control or the control panel. Example:

button About the Use of "This Product" or "This Projector"

As well as the main projector unit, supplied items or optional extras may be referred to using the phrase "this product" or "this projector". 2 Contents Organization of the Guide and Notations in the Guide Using Each Guide . 1 Notations Used in This Guide . 2 Safety Indications . 2 General Information Indications . 2 About the Use of "This Product" or "This Projector"

. 2 Introduction Part Names and Functions . 6 Front/Top . 6 Control Panel

. 7 Remote Control

. 9 Rear . 12 Base . 13 Preparing Installing . 14

. 14 Projected Image and Position of Projector . Installing in parallel with the screen . 14 Installing the projector horizontally by adjusting the height of either side . 14 Various Setting Methods . 15 Placing on a table and projecting . 15 Suspending from the ceiling and projecting

. 16 Projection Distance and Lens Shift Maximum Values . 16 Connecting a Device . 19 Removing the Terminal Cover . 19 Connecting Video Equipment . 19 Connecting a Computer . 20 Connecting External Equipment . 20 Connecting to the Trigger Out port . 20 Connecting WirelessHD devices (EH-

TW9400W/EH-TW8400W only) . 20 Connecting to the LAN port . 21 Attaching the Wireless LAN unit . 21 Connecting an HDMI Cable Clamp . 22 Preparing the Remote Control . 23 3 Installing the Remote Control Batteries . 23 Remote Control Operating Range . 24 Operating range (left to right) . 24 Operating range (top to bottom) . 24 Basic Operations Projecting Images . 25 Turning On the Projector . 25 If the target image is not projected . 26 Using the Home Screen . 26 Turning Off . 27 Adjusting the Projected Image . 28 Displaying the Test Pattern . 28 Lens Adjustment Function (Focus, Zoom, Lens Shift) . 28 Adjusting the focus . 29 Adjusting the projection size (Zoom Adjustment) . 29 Adjusting the position of the projected image (Lens Shift Adjustment) . 30 Adjusting the Projector's Tilt . 31 Correcting Keystone Distortion . 31 Hiding the Image Temporarily . 31 Adjusting the Image Adjusting the Image . 32 Selecting the Projection Quality (Color Mode)

. 32 Switching the Screen Between Full and Zoom

(Aspect) . 33 Adjusting the Sharpness . 34 Adjusting Image Resolution (Image Enhancement) . 35 Setting Auto Iris . 36 Setting Frame Interpolation . 36 Adjusting the Color . 38

. 38 Adjusting the Color Temp. Adjusting the RGB (Offset and Gain) . Adjusting Hue, Saturation, and Brightness . 38

. 38 Adjusting the Gamma . 40 Select and adjust the correction value . 40 Contents Adjust using the gamma adjustment graph

. 40 Selecting the Computer's Wireless LAN Settings

. 67 Viewing the Image at the Saved Image Quality (Memory Function) . 42 Saving a Memory . 42 Loading, Deleting, and Renaming a Memory

. 42 Useful Functions Enjoying 3D Images . 44 Preparing to View 3D Images . 44 If the 3D image cannot be viewed . 44 Using 3D Glasses . 45 Warnings Regarding Viewing 3D Images . Connecting with WirelessHD

. 45

. 47 Installing the WirelessHD Transmitter . 47 WirelessHD Transmitter part names . 48 WirelessHD Transmitter connection example and signal flow . 49 Setting the WirelessHD Transmitter . 54 Projecting Images . 54 WirelessHD Settings Menu . 56 WirelessHD Transmission Range . 57 Operating the Remote Control

. 58 Remote Control Operating Range . 58 Switching the Input and Output . 58 Switching the target image . 59 Switching the image source . 60 Using the HDMI Link Function . 61 HDMI Link Function . 61 HDMI Link Settings . 61 Connecting . 62 Using the Projector on a Network Projecting Using Wired LAN . 63 Selecting Wired Network Settings . 63 Projecting Using Wireless LAN . 65 Selecting Wireless Network Settings Manually

. 65 4 Selecting wireless network settings in Windows . 67 Selecting wireless network settings in OS X

. 67 Setting Up Wireless Network Security . 68 Projecting in Epson iProjection (iOS/Android)

. 68 Operating using a smartphone (remote control function) . 69 Configuration Menu Configuration Menu Functions . 71 Configuration Menu Operations . 71 Configuration Menu Table . 72 Image menu . 72 Signal menu . 74 Settings menu . 75 Extended menu . 78 Network menu . 82 Info menu . 86 Reset menu . 86 Troubleshooting Problem Solving . 87 Reading the Indicators . 87 Indicator status during an error/warning . 87 Indicator status during normal operation . 89 When the Indicators Provide No Help . 89 Check the problem . 89 Problems relating to images . 90 Problems when projection starts . 94 Problems with the remote control

. 94 Problems with the control panel

. 94 Problems with 3D . 95 Problems with HDMI

. 95 Problems with WirelessHD (EH-TW9400W/

EH-TW8400W only) . 96 Network problems . 98 About Event ID . 98 Contents Maintenance Maintenance . 100 Cleaning the Parts . 100 Cleaning the air filter . 100 Cleaning the main unit . 101 Cleaning the lens . 102 Replacement Periods for Consumables . 102 Air filter replacement period . 102 Lamp replacement period . 102 Replacing Consumables . 102 Replacing the air filter . 102 Replacing the lamp . 103 Resetting lamp hours . 105 Panel Alignment . 106 Color Uniformity . 108 About PJLink . 110 Appendix Optional Accessories and Consumables . 111 Optional Items . 111 Consumables . 111 Supported Resolutions . 112 PC . 112 SD . 112 HD . 113 4K . 113 3D . 114 3D Input Signals MHL (via a WirelessHD Transmitter*) . 115 WirelessHD Input Signal MHL* . 115 Specifications .. 116 Appearance . 119 List of Safety Symbols . 120 Glossary . 122 General Notes . 123 Warning Labels . 123 General Notice . 124 5 Introduction Part Names and Functions Front/Top Name a Lamp cover b Air exhaust vent Function Open when replacing the projector's lamp. s p.103 Exhaust vent for air used to cool the projector internally. Caution While projecting, do not put your face or hands near the air exhaust vent, and do not place objects that may become warped or damaged by heat near the vent. Hot air from the air exhaust vent could cause burns, warping, or accidents to occur. c Lens shutter d Lens e Air intake vent Air filter cover f Remote receiver g Control panel Links to the projector's power on/off function, and automatically opens and closes the shutter. s p.25 Images are projected from here. Intake vent for air used to cool the projector internally. When replacing the air filter, open this cover and remove the air filter. s p.102 Receives signals from the remote control. s p.24 Operates the projector. s p.7 6 Introduction Control Panel When the Illumination function is set to Off, all indicators are off under normal projection conditions.s Extended - Operation - Illumination p.78 Buttons/Indicators Function a b c d e f Control panel cover g h i Flashes to indicate warm-up in progress or cool-down in progress. Shows the projector's status through a combination of other indicators lit and flashing. s p.87 Flashes orange when it is time to replace the lamp. Shows the projector's errors through a combination of other indicators lit and flashing. s p.87 Flashes orange if the internal temperature is too high. Shows the projector's errors through a combination of other indicators lit and flashing. s p.87 Displays and closes the Configuration menu. On the Configuration menu, you can make adjustments and settings for Signal, Image, Input Signal, and so on. s p.71 Selects functions and settings when a menu is displayed. s p.71 Cover for the control panel. When you want to use the control panel, grip the knob and slide the cover open. Selects the adjustment value for the keystone correction and for menu items. s p.31 Selects adjustment values for menu items. s p.71 Returns to the previous menu level when a menu is displayed. s p.71 7 Introduction Buttons/Indicators Function j k l Changes the adjustment items for the motorized lens function. The adjustment items are as follows. Focus s p.29 Zoom s p.29 Lens shift s p.30 Changes to the image from each input port. s p.26 Turns the projector on or off. s p.25 Lit when the projector is on. Shows the projector's errors through a combina-

tion of other indicators lit and flashing. s p.87 8 Introduction Remote Control The remote control varies depending on the projector model you are using. This examples in this section are for the remote control for the EH-TW9400W/EH-TW8400W. a b c d e f Button Function Turns the projector on. s p.25 Displays and closes the Home screen. s p.26 Changes to the image from each input port. s p.26 is only available for the EH-TW9400W/

EH-TW8400W. Performs operations such as play, stop, and volume adjustment for connected devices that meet the HDMI CEC standards. s p.61 When HDMI Link is On sSettings - HDMI Link - HDMI Link p.75 Displays the device connections list. When HDMI Link is Off sSettings - HDMI Link - HDMI Link p.75 Displays the HDMI link settings menu. s p.61 Changes the adjustment items for the motor-

ized lens function. The adjustment items are as follows. Focus s p.29 Zoom s p.29 Lens shift s p.30 9 Introduction g h i j k l m n o p q r s t A Button Function Selects menu items and adjustment values. s p.71 The adjustment value returns to its default value when pressed while the menu's adjust-

ment screen is displayed. s p.71 Displays and closes the Configuration menu. On the Configuration menu, you can make adjustments and settings for Signal, Image, and so on. s p.71 Saves, loads, or erases a memory. s p.42 Sets the strength for Frame Interpolation. s p.36 Adjusts the hue, saturation, and brightness for each RGBCMY color. s p.38 Performs the function assigned to the user button. s p.75

(EH-TW9400W/EH-TW8400W only) This is the button for controlling the Wire-

lessHD Transmitter. Turns on the WirelessHD Transmitter, or switches the input and output. Make sure you point the remote control at the WirelessHD Transmitter when performing operations. s p.47 Changes the 3D format. This projector supports the following 3D for-

mats. Frame Packing Side by Side Top and Bottom s p.44 The adjustment screen for the dynamic range is displayed.s p.74 Displays and closes the test pattern. s p.28 Loads the lens position registered as Memo-

ry1 or Memory2 in the Save Lens Position. s p.42 Returns to the previous menu level when a menu is displayed. s p.71 When a menu is displayed, it accepts and en-

ters the current selection and moves to the next level. s p.71 10 Introduction Button Function Displays the Image Enhancement menu. s p.35 Changes the Color Mode. s p.32 Selects the aspect mode according to the in-

put signal.s p.33 Temporarily stops projection. To turn the im-

age back on, press this button again. s p.31 The remote control buttons light up for ap-

proximately 10 seconds. This is useful when operating the remote control in the dark. Turns the projector off. s p.27 B C D E F G 11 Introduction Rear Name a Security slot (

) b Power inlet c Remote receiver d Opt.HDMI port e HDMI1 port f HDMI2 port g USB-A port h Service port i LAN port j PC port k RS-232C port l Trigger Out port Function The security slot compatible with the MicroSaver security system manufac-

tured by Kensington. For more details, visit the homepage of Kensington at http://www.kensington.com/. Connect the power cord. s p.25 Receives signals from the remote control. s p.24 Connects the power supply port for the optical HDMI cable. However, con-

nection for all the devices is not guaranteed. Make sure to check if your device works beforehand. Connects HDMI compatible video equipment and computers.s p.19 HDMI1/HDMI2 ports support HDCP 2.2. Connects the optional Wireless LAN unit. It is also used when updating the firmware. s p.21 Service port. This is not normally used. Connects a LAN cable to connect to a network. s p.21 Connects to the RGB output port on a computer. s p.20 When controlling the projector, connect the projector to a computer with an RS-232C cable. This port is for control use and should not normally be used. Connects with external devices such as motorized screens. s p.20 12 Introduction Base LENS Name Function a Ceiling mount fixing points b c d Rear foot e Cable cover fixing screw f Front adjustable foot g Screw holes for ana-

morphic lens Attaches the optional ceiling mount here when suspending the projector from a ceiling. s p.111 Use the four ceiling mount fixing points for stallation environment. Use the in a small room. Remove this when using the fixing points when installing next to a wall ceiling mount fixing points. depending on the in-

or Screw holes for attaching the cable cover. When set up on a surface such as a table, extend the foot to adjust horizontal tilt. s p.31 Screw holes for attaching the anamorphic lens. 13 Preparing Installing Projected Image and Position of Projector Install the projector as follows. Installing in parallel with the screen If the projector is installed at an angle to the screen, keystone distortion occurs in the projected image. Adjust the projector's position so that it is installed in parallel with the screen. c If the projector cannot be installed in front of the screen, you can adjust the position of the image by using lens shift. s p.30 Installing the projector horizontally by adjusting the height of either side If the projector is tilted, the projected image is also tilted. Install the projector horizontally so that both sides are at the same height. If the projector cannot be installed horizontally, you can adjust the projector's tilt with the front foot. s p.31 14 Preparing Various Setting Methods Warning A special method of installation is required when suspending the projector from a ceiling (ceiling mount). If it is not installed correctly, it could fall, causing an accident and injury. If you use adhesives, lubricants, or oil on the ceiling mount fixing points to prevent screws from loosening, or if you use items such as lubricants or oils on the projector, the outer projector case may crack, which causes it to fall from its ceiling mount. This could cause serious injury to anyone under the projector and also damage the projector. Do not set up the projector in locations exposed to high humidity and dust, such as on a kitchen counter, in the kitchen, or near a humidifier, or in locations exposed to oil smoke or steam. Doing so could cause fire or electric shock. In addition, the oil content could cause the projectors outer case to deteriorate and could cause the projector to fall off from the ceiling where it is suspended. Do not install it on an unstable shelf or in a place out of load range. Otherwise, it could fall or topple causing an accident and injury. When installing it in a high position such as on a shelf, take measures against falling by using wires to ensure the safety in an emergency, such as an earthquake, and prevent accidents. If it is not installed correctly, it could fall causing an accident and injury. Do not block the air intake vent and air exhaust vent of the projector. Blocking its air intake vent and air exhaust vent may trap heat inside causing fire. Attention Do not use the projector installed vertically. Doing so could cause a malfunction. Clean the air filter once every three months. Clean it more often if the environment is particularly dusty. s p.100 Placing on a table and projecting You can install the projector on a table in your living room or on a low shelf to project images. 15 Preparing Suspending from the ceiling and projecting You can suspend the projector from the ceiling with the optional ceiling mount to project images. c When suspending from the ceiling and projecting, set Projection to Front/Ceiling or Rear/

Ceiling. s Extended - Projection p.78 Projection Distance and Lens Shift Maximum Values The size of the projection increases as the projector is moved away from the screen. Use the table below to setup the projector at the optimum position from the screen. The values given here are for your reference only. The maximum lens shift adjustment values are shown in the following table. c The projected image becomes smaller after correcting distortion. Increase the projection distance to fit the projected image to the screen size. When adjusting the projection position vertically in lens shift A : Distance from the center of the lens to the bottom edge of the projected image (when lens shift is raised to its highest level) B : Distance from the center of the lens to the bottom edge of the projected image (when lens shift is lowered to its lowest level) Projection distance from the projector to the screen Size of the projected image E F

:

:

16 Preparing When adjusting the projection position horizontally in lens shift C :

D :

:

E F

:

Lens center movement distance when the projector is moved (when lens shift is set to maximum left) Lens center movement distance when the projector is moved (when lens shift is set to maximum right) Projection distance from the projector to the screen Size of the projected image 16:9 Screen Size F W x H Projection Distance (E) Minimum Maximum

(Wide)

(Tele) Unit: cm Lens Shift Maximum Values*

Distance

(A) Distance

(B) Distance

(C, D) 50"

60"

80"

100"

150"

200"

250"

300"

* Vertical and horizontal lens shift cannot both be set to their maximum values. s p.30 111 x 62 133 x 75 177 x 100 221 x 125 332 x 187 443 x 249 553 x 311 664 x 374 313 376 503 630 947 1264 1582 1899 148 178 239 300 452 604 756 908 29 35 46 58 86 115 144 173 91 109 146 182 273 364 455 547 52 63 83 104 156 209 261 313 17 Preparing Installation example (with 16:9 screen size and 100") Side view Overhead view 18 Preparing Connecting a Device Attention Make cable connections before connecting to a power outlet. Check the shape of the cable's connector and the shape of the port, and then connect. If you force a connector of a different shape into the port, it could cause damage and a malfunction to occur. Removing the Terminal Cover Depending on the model you are using, the projector may have a terminal cover for the connector section on the rear to improve the overall appearance of the projector. Remove the terminal cover before connecting any cables. There are gaps at the bottom of the terminal cover that allow you to pull the cover forward and lift it from the grooves at the top. When reattaching, first insert the protruding sections into the grooves at the top. Connecting Video Equipment To project images from DVD/Blu-ray players, connect to the projector using one of the following methods. When using a commercially available HDMI cable c To display signals in the 18 Gbps transmission band, such as 4k60p/4:4:4, use a premium HDMI cable. If you use a cable that does not support it, images may not be displayed properly. If you experience any trouble displaying images at 18 Gbps. change the EDID setting to Normal. sSignal-Advanced-

EDID p.74 When using the power supply port for an optical HDMI cable, connect it to the Opt.HDMI port. HDMI1/HDMI2 ports support HDCP 2.2. This projector does not have a built-in speaker. Connect the projector to your AV system to listen to audio from connected equipment. 19 Preparing Connecting a Computer To project images from a computer, connect the computer using one of the following methods. When using a commercially available computer cable When using a commercially available HDMI cable Connecting External Equipment Connecting to the Trigger Out port To connect external devices such as motorized screens, connect a mini-jack stereo cable (3.5 mm) to the Trigger Out port. When set to on, a signal (12 V DC) is output from this port to communicate the projector's status (On or Off) to connected devices such as electric screens. c To use the Trigger Out port, set Trigger Out to Power (EH-TW9400W/EH-TW9400 only) or On (EH-

TW8400W/EH-TW8400 only). s Extended - Operation - Trigger Out p.78 Connecting WirelessHD devices (EH-TW9400W/EH-TW8400W only) The projector receives transmissions from the WirelessHD Transmitter, and projects the images. s p.47 Change the projected image by pressing the control panel. button on the remote control or the button on the c When receiving WirelessHD images, make sure WirelessHD is set to On. sSettings - WirelessHD -

You can change which device is displayed by selecting a device from Device Connections in HDMI WirelessHD p.75 Link. sSettings-HDMI Link-Device Connections p.75 20 Preparing Connecting Smartphones or Tablets You can connect MHL compatible smartphones or tablets to the WirelessHD Transmitter. Use an MHL compatible cable to connect the micro USB port of smartphones and tablets to the HDMI4 port on the WirelessHD Transmitter. You can operate smartphones or tablets from the projector remote control. You can also view video and listen to music while charging a smartphone or tablet. Attention Make sure the connection cable supports the MHL standards. During charging, the smartphone or tablet could generate heat, cause a liquid leak, explode or generate other conditions that could result in a fire. When a connection is made using an MHL-HDMI conversion adapter, it may not be possible to charge or control the device from the remote control. c Some devices use more power during video playback than what is supplied and will therefore not enable charging during video playback or other operations. Connecting to the LAN port Connect to a network router, a hub, and so on, with a 100BASE-TX or 10BASE-T LAN cable. You can operate the projector or check its status over a network from a computer or a smart device. c To prevent malfunctions, use a category 5 or higher shielded LAN cable. Attaching the Wireless LAN unit To use the wireless LAN function, attach an optional Wireless LAN unit (ELPAP10). Connect the Wireless LAN unit to the USB port. 21 Preparing You can use one of the following methods to project over wireless LAN. For more details, see the download page. Projecting four screens simultaneously When using Epson iProjection (Windows/Mac), you can display up to four separate screens from the projector from up to 50 computers connected to the network. Download Epson iProjection from the following Web site. http://www.epson.com Projecting images from a mobile terminal via a network By installing Epson iProjection (iOS/Android) on a smartphone or tablet, you can wirelessly project data on your device.s p.68 c When not using the wireless LAN function with the Wireless LAN unit kept inserted, set Wireless LAN When using Epson iProjection in Quick connection mode, we recommend making security settings. Power to Off. This can prevent unauthorized access from outsiders. s p.82 s p.84 Connecting an HDMI Cable Clamp If the HDMI cable is thick and hangs down, make sure you secure it to the cable holder with an HDMI clamp so that the cable's weight does not disconnect it from the port. 22 Preparing Preparing the Remote Control Installing the Remote Control Batteries Attention Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the correct way. You cannot use other batteries except for the AA size manganese or alkaline. a Remove the battery cover. While pushing the battery compartment cover catch, lift the cover up. c Reattach the battery cover. Press the cover until it clicks into place. b Replace the old batteries with new batteries. Check the polarity of the batteries (+) and

(-) before installing. c If delays in the responsiveness of the remote control occur or if it does not operate, it probably means that the batteries are becoming flat. When this happens, replace them with new batteries. Have two AA size manganese or alkaline batteries ready. 23 Preparing Remote Control Operating Range The operation range for the WirelessHD Transmitter differs. s p.58 Operating range (left to right) Operating range (top to bottom) 10m 30 30 30 30 10m 60 10m 10 30 30 10m 24 Basic Operations Projecting Images Turning On the Projector a Connect the equipment to the projector. b Connect using the power cord supplied. The projector's power indicator turns blue. This indicates that the projector is receiving power, but is not yet turned on (it is in standby mode). c Turn on the connected equipment. d Press the button on the remote button on the control or the control panel to turn on the projector. Remote control Control panel

(operation indicator) flashes blue The lens shutter opens, and projection starts. The as the projector warms up. Once the projector is warmed up, the operation indicator stops flashing and turns blue. c When Direct Power On is set to On, you can start projecting by simply connecting the power cord to the projector without having to press any buttons. s Extended -

Operation - Direct Power On p.78 Warning Do not look into the lens during projection. The powerful light emitted could cause damage to eyesight. Pay close attention to how your child behaves. Do not stand in front of the lens during projection. Clothes could be damaged due to the high temperature. c This projector provides a Child Lock function to prevent children from accidentally turning the power on and a Control Panel Lock function to prevent accidental operations and so on. s Settings - Lock Setting - Child Lock/Control Panel Lock p.75 This projector provides an Auto Setup function to automatically select the optimum settings when the input signal for the connected computer image changes. s Signal - Auto Setup p.74 When using at an altitude of 1500 m or more, set High Altitude Mode to On. s Extended - Operation -

High Altitude Mode p.78 25 Basic Operations If the target image is not projected If the image is not projected, you can change the source using one of the following methods. Remote control Press the button for the target port. Control panel Press the Press the button and select the target port. button to confirm the selection. Using the Home Screen button on the remote control to display the Home screen. The Home screen feature allows you to easily select an image source and access useful functions. Press the Under the following conditions, the Home screen is displayed automatically when the projector is turned on. Home Screen Auto Disp. is set to On. s Extended - Home Screen - Home Screen Auto Disp. p.78 There are no signals from any sources. a Selects the source you want to project. b Connection Guide is displayed. c Displays the Configuration menu. s p.71 d Performs menu options assigned to Home Screen in the Extended menu. sExtended - Home Screen p.78 e Sets the 3D function. sSignal - 3D Setup p.74 f Selects the Color Mode. s p.32 26 Basic Operations c The Home screen disappears after 10 minutes of inactivity. Turning Off a Turn off the connected equipment. c Press the button again. Projection ends, and the lens shutter closes automatically. The operation indicator flashes and the projector begins to cool down. d Wait until cool-down is complete. When cool-down is complete, the operation indicator stops flashing. e Disconnect the power cord. b Press the button on the remote control or the control panel. Remote control button on the Control panel A confirmation message is displayed. 27 Basic Operations Adjusting the Projected Image Displaying the Test Pattern When adjusting the zoom/focus or the projection position just after setting up the projector, you can display a test pattern instead of connecting video equipment. Press the at the top and bottom uses 2.40:1 CinemaScope. button on the remote control to display the test pattern. The standard for horizontal lines When you select Color Isolation while projecting images, the color selected from R (red), G (green), or B (blue) is projected (EH-TW9400W/EH-TW9400 only). Press the button again to end the test pattern display. Lens Adjustment Function (Focus, Zoom, Lens Shift) To adjust the focus, zoom, or lens shift, press the the control panel, and then select the item you want to adjust. button on the remote control or the button on Remote control Control panel The adjustment items switch as shown in the following table. 1 Focus adjustment 2 3 Zoom adjustment Lens shift adjustment Adjust Focus is displayed on the screen. Adjusts the focus of the projected image. s p.29 Adjust Zoom is displayed on the screen. Adjusts the size of the projected image. s p.29 Adjust Lens Shift is displayed on the screen. Adjusts the position of the projected image. s p.30 To finish making adjustments, press the c You can register the results of lens adjustment to the memory (Save Lens Position). You can load the lens position that you registered from the remote control or the Configuration menu. button in Lens shift adjustment. 28 Basic Operations Adjusting the focus a Press the Adjust Focus is displayed on the screen. button on the remote control. b Press the buttons to adjust the focus. c Press the button three times to finish making adjustments. Adjusting the projection size (Zoom Adjustment) a Press the Adjust Zoom is displayed on the screen. button on the remote control twice. b Press the buttons to adjust the size of the projected screen. c Press the button twice to finish the adjustment. 29 Basic Operations Adjusting the position of the projected image (Lens Shift Adjustment) If the projector cannot be installed directly in front of the screen, you can adjust the position of the image by using lens shift. button on the remote control three times. Adjust Lens Shift is displayed on the screen. a Press the b Use the buttons to adjust the position of the image. You can move the image within the range indicated by the dotted line in the following figure. c To move the lens position back to the cen-

button for at least three ter, hold the seconds. c Press the button to finish the adjustment. c When the following message is displayed when you change to Adjust Lens Shift, the image moves in the opposite direction to the direction pressed with the buttons. When Front/Ceiling or Rear/Ceiling is set for Projection, select Inverted. s Extended -

Projection p.78 Caution When transporting the projector, set the lens position to the center. If you transport the projector when the lens is not in the central position, the lens shift mechanism could be damaged. Do not put your finger in the moving parts of the projector's lens. Otherwise an injury could occur. c When you cannot install the projector directly in front of the screen, it is recommended that you use If finely adjusting the lens shift does not work, press briefly on the arrow buttons to perform minute lens shift to adjust the projection position. adjustments while viewing the image. 30 Basic Operations Adjusting the Projector's Tilt If the projected image is horizontally tilted (the left and right sides of the projected image are at different heights) when the projector is setup on a table, adjust the front foot so that both sides are level with each other. Correcting Keystone Distortion buttons on the control panel to correct keystone distortion. You can use the Open the control panel cover at the side to operate the control panel. s p.7 Press the When the gauges are displayed, press the buttons to display the adjustment gauges. and or buttons to perform vertical correction. When the top or bottom is too wide c When you correct keystone distortion, the projected image may be reduced. Increase the projection distance to fit the projected image to the screen size. You can make keystone settings from the Configuration menu. s Settings - Keystone p.75 You can make effective corrections within a projection angle of 30 top to bottom. Hiding the Image Temporarily You can use this to temporarily hide the image on the screen. Press the button to show or hide the image. c For movies, because the movie continues to play even when it is hidden, you cannot return to the point at which you hid the image using the button. 31 Adjusting the Image Adjusting the Image Selecting the Projection Quality (Color Mode) You can obtain the optimum image quality to suit your surroundings when projecting. The brightness of the image varies depending on the mode selected. a Press the button. c You can make settings from the Configuration menu. s Image - Color Mode p.72 If you press the button, you can also make settings from the Home screen.s p.26 b Select Color Mode. Use the selection. buttons to select a mode, and then press the button to confirm the Choices when projecting 2D images Mode Dynamic Bright Cinema Natural Cinema Digital Cinema Application This is the brightest mode. Best for prioritizing brightness. Best for projecting vivid images. Best for faithfully reproducing the color of the source image. We recommend selecting this mode when performing color adjustment for the image. s p.38 Best for enjoying content such as movies. Projects images in the Digital Cinema color space. Best for prioritizing colors. Choices when projecting 3D images Mode 3D Dynamic 3D Cinema Application A dedicated 3D mode best for prioritizing brightness. A dedicated 3D mode best for enjoying content such as movies. 32 Adjusting the Image Switching the Screen Between Full and Zoom (Aspect) You can change the input signal's type, aspect ratio, and resolution to match the Aspect of the projected image. The available settings vary depending on the image signal currently being projected. c Note that using the aspect ratio function of the projector to reduce, enlarge, or split the projected image for commercial purposes or for public viewing may infringe upon the rights of the copyright holder of that image based on copyright law. a Press the button. b Use the buttons to select the setting name, and then press the button to confirm the selection. c You can make settings from the Configuration menu. s Signal -

Aspect p.74 c You may not be able to change the Aspect depending on the input signal. By normally selecting Auto, the optimum aspect is used to display the input signal. Change the setting if you want to use a different aspect. The table below shows the image projected on a 16:9 screen. Normal Setting Name Full Zoom Input Image 4:3 Images 16:9 Images*1 Images Recorded Using Squeeze Letterbox Images*2 33 Adjusting the Image Input Image Notes Normal Matches the vertical size of the projection panel. The aspect ratio differs de-

pending on the input im-

age. Setting Name Full Uses the entire projection panel. The aspect ratio dif-

fers depending on the in-

put resolution. Zoom Retains the aspect ratio of the input signal, and matches the horizontal size of the projection pan-

el. The top and bottom of the image may be trunca-

ted.

*1 The full and zoom used for 16:9 signal input cannot be used for 4K and 3D signals, as well as for the PC image signal.

*2 The letterbox image used in this explanation is a 4:3 aspect ratio image displayed in 16:9 with black margins at the top and bottom for subtitle placement. The margins at the top and bottom of the screen image are used for subtitles. For EH-TW9400W/EH-TW9400, you can also set Anamorphic Wide and Horiz. Squeeze. Set Anamorphic Wide and attach a commercially available anamorphic lens to enjoy DVDs, Blu-rays, and so on of images recorded at Cinema Scope size. Horiz. Squeeze stretches the horizontal aspect of the input signal. This allows you to project across the full width of the screen when using a commercially available anamorphic lens. c If Anamorphic Wide is selected when Overscan is set, the image may be truncated. Set Overscan to Off.s Signal-Overscan p.74 When projecting 3D images in Anamorphic Wide, only 1080p/24 Hz/frame packing signals are When a 4K image signal is being input, you can only select Normal, Anamorphic Wide, and Horiz. supported. Squeeze. Adjusting the Sharpness You can make the image clearer. The following shows the setting items and procedures. Standard Thin Line Enhancement Thick Line Enhancement Enhances the outlines for the projected image overall. When you adjust Stand-

ard, the adjustment values for Thin Line Enhancement and Thick Line En-

hancement are also adjusted. Details such as hair and patterns on clothing are enhanced. Rough parts such as outlines for entire subjects or the background are enhanced, making the overall image clearer. a Press the button. The Configuration menu is displayed. b Select Image - Sharpness. The Sharpness adjustment screen is displayed. 34 Adjusting the Image c Use the buttons to select the item, and then use the buttons to make the adjustments. The image is enhanced when moved to the right (positive) and softer when moved to the left (negative). d Press the menu. button to exit the Press the button to return the adjustments to their default values. Adjusting Image Resolution (Image Enhancement) You can adjust the resolution of the image using the Image Enhancement function. The following content can be adjusted. 4K Enhancement Image Preset Mode Noise Reduction MPEG Noise Reduction Super-resolution Detail Enhancement 4K Enhancement is a function that projects an image at a doubled res-

olution by diagonally shifting 1 pixel in increments of 0.5 pixels. A high-resolution image signal is projected in fine detail. Select the settings prepared in advance as the settings for Noise Re-

duction, MPEG Noise Reduction, Super-resolution, and Detail En-

hancement.

(This can be specified only when Image Processing is set to Fine.) Smoothes out rough images.

(This can be specified only when Image Processing is set to Fine.) You can reduce dot and block noise that occurs in outlines when pro-

jecting MPEG movies. Fine Line Adjust: Enhances the contrast and the outlines of complicated images. Soft Focus Detail: Enhances the contrast and the outlines for smooth backgrounds. Enhances the contrast in an image to create a more emphatic texture and material feel. Strength: The larger the value, the stronger the contrast. Range: The larger the value, the wider the range of detail enhancement becomes. 35 Adjusting the Image a Press the button. c You can make settings from the Configuration menu. s Image -

Image Enhancement p.72 b Use the buttons to select the item you want to adjust, and button to confirm then press the the selection. c Use the buttons to make button to adjust another adjustments. Press the item. Press the button to return the adjustments to their default values. d Press the menu. button to exit the Setting Auto Iris By automatically setting the luminance according to the displayed image, you can enjoy deep and rich images. You can select the luminance adjustment tracking for changes in brightness in the displayed image from Normal to High Speed. Press the order. Image - Auto Iris Use the press the button to display menus in the following buttons to select the item, and then button to confirm the selection. c Depending on the image, you may hear the Auto Iris operating, but this is not a malfunction. Setting Frame Interpolation You can play fast moving images smoothly by automatically producing intermediate frames between the original frames. Frame Interpolation is available under the following conditions. When Image Processing is set to Fine. s Signal - Advanced - Image Processing p.74 When the source is HDMI1, HDMI2, or WirelessHD (EH-TW9400W/EH-TW8400W only). 36 Adjusting the Image When inputting 2D signals* or 3D signals (1080p 24 Hz). s p.112

* This is unavailable when a 4K signal is being input. This is enabled only when 4K Enhancement is set to On and 1080p 24 Hz signals are being input.s Image - Image Enhancement - 4K Enhancement p.72 b Use the buttons to select the item, and then press the button to confirm the selection. a Press the button. c You can make settings from the Configuration menu. s Image -

Frame Interpolation p.72 37 Adjusting the Image Adjusting the Color Adjusting the Color Temp. You can adjust the overall tint of the image. Make adjustments if the image is a little too blue or too red and so on. button to display menus in the following Press the order. Image - Color Temp. - Color Temp. buttons to make adjustments. Use the Blue tints grow stronger as the value is increased, and red tints grow stronger as the value is reduced. c Press the button to return the adjustments to their default values. Adjusting the RGB (Offset and Gain) You can adjust the brightness of dark areas (Offset) and bright areas (Gain) for R (red), G (green), and B (blue). button to display menus in the following Press the order. Image - Color Temp. - Customized Use the use the becomes brighter when moved to the right (positive) and darker when moved to the left (negative). buttons to select the item, and then buttons to make the adjustments. The image Offset Gain When the image is made brighter, shading for the darker sections is more vividly expressed. When the image is made darker, the image appears more full-bodied but shading for the darker sections is harder to distinguish. When the image is made brighter, the bright sections become whiter and shading is lost. When the image is made darker, shading for the bright sections is more vividly expressed. c Press the button to return the adjustments to their default values. Adjusting Hue, Saturation, and Brightness You can adjust the hue, saturation, and brightness for each of the R (red), G (green), B (blue), C (cyan), M

(magenta), and Y (yellow) colors. Hue Saturation Brightness Adjusts the overall color of the image to be blue, green, or red. Adjusts the overall vividness of the image. Adjusts the overall color brightness of the image. 38 Adjusting the Image a Press the button. c You can make settings from the Configuration menu. s Image -

Advanced - RGBCMY p.72 b Use the buttons to select the color you want to adjust, and then press the confirm the selection. button to c Use the select Hue, Saturation, or Brightness. buttons to d Use the adjustments. buttons to make button to adjust another Press the color. Press the button to return the adjustments to their default values. e Press the menu. button to exit the 39 Adjusting the Image Adjusting the Gamma You can adjust slight coloration differences that may occur due to the device being used when the image is displayed. You can set it by using one of the following three methods. Select and adjust the correction value Adjust using the gamma adjustment graph Select and adjust the correction value a Press the menus in the following order. Image - Advanced - Gamma button to display buttons to b Use the select the correction value, and then button to confirm the press the selection. The larger the value, the lighter the dark portions of the image become, but bright areas may appear discolored. The upper part of the gamma adjustment graph becomes rounded. The smaller the value, the darker the bright portions of the image become. The lower part of the gamma adjustment graph becomes rounded. c The horizontal axis of the gamma adjustment graph shows the input signal level, and the vertical axis shows the output signal level. Select Reset to return the adjustments to their default values. Adjust using the gamma adjustment graph Select a tone point on the graph and make adjustments. button to display a Press the menus in the following order. Image-Advanced-Gamma-

Customized 40 c Use the buttons to adjust the brightness, and then press the selection. button to confirm the Adjusting the Image buttons to select the b Use the tone you want to adjust from the graph. 41 Adjusting the Image Viewing the Image at the Saved Image Quality

(Memory Function) Saving a Memory By using the memory function, you can register the following adjustment values, and then load them when necessary. Image setting from the Configuration menu Adjustment values for Lens Adjustment Function (Focus, Zoom, Lens Shift, Blanking) s p.28 a Make the settings or adjustments you want to register. b Press the button. c Use the buttons to select Save Memory or Save Lens Position, and then press the button to confirm the selection. d Use the buttons to select the memory name to be saved, and then press the confirm the selection. button to The current projector settings are saved to the memory. If the mark on the left of the memory name is turned aqua, it means the memory has already been registered. When you select a registered memory, a message is displayed asking you to confirm that you want to overwrite the memory. If you select Yes, the previous content is erased and the current settings are saved. Save Memory: Registers the Image settings Save Lens Position: Registers the adjustment value for the lens adjustment function Loading, Deleting, and Renaming a Memory You can load, delete, and rename registered memories. Press the button, and then select the target function on the screen displayed. c Press the Position registered in Memory1 or Memory2. The position of the lens when loading the memory and the position of the lens when the memory is buttons on the remote control to load the lens position from the Save Lens registered may not be exactly the same. 42 Adjusting the Image Function Load Memory Erase Memory Rename Memory Load Lens Position Erase Lens Position Rename Lens Position Explanation Loads the saved memory. When you select a memory and press the button, the settings applied to the current image are replaced with the settings from the memory. Erases the registered memory. When you select a memory name and press the button, a message is displayed. Select Yes, and then press the button to erase the selected memory. Changes the memory name. Select the memory name you want to change, and then press the the soft keyboard. s p.83 When you have finished, move the cursor over Finish, and then press the button. Enter the memory name using button. Loads the registered lens position memory. When you select the lens po-

sition name and press the button, the adjustment value for the se-

lected lens position memory is applied. Erases the registered lens position memory. When you select a lens posi-

button, a message is displayed. Select Yes, tion name and press the and then press the button to erase the selected lens position memory. Changes the lens position memory name. Select the lens position memory name you want to change, and then press the button. Enter the lens position memory name using the soft keyboard. s p.83 When you have finished, move the cursor over Finish, and then press the button. 43 Useful Functions Enjoying 3D Images Preparing to View 3D Images To view 3D images, be sure to prepare a pair of commercially available 3D Glasses with an active shutter system that supports radio waves (RF/Bluetooth) communication system in advance. Check the following before viewing 3D images. When the source is HDMI1, HDMI2, or WirelessHD (EH-TW9400W/EH-TW8400W only). Set 3D Display to Auto or 3D. When this is set to 2D, change to Auto or 3D. s Signal - 3D Setup - 3D Display p.74 Pair 3D Glasses. This projector supports the following 3D formats. Frame Packing Side by Side Top and Bottom If the 3D image cannot be viewed The projector automatically projects a 3D image when detecting a 3D format. Some 3D TV broadcasts may not contain 3D format signals. If this happens, follow the steps below to set the 3D format. a Press the menus in the order Signal - 3D Setup. button to display c Press the format on the AV device. button to set the 3D b Set 3D Display to 3D. c If you are using a device or cable that does not support 3D images, 3D projection cannot be performed. For details on 3D format settings on the AV device, see the documentation supplied with the AV device. When the 3D format has not been correctly set up, an image will not be correctly projected as shown below. If a 3D image is not projected correctly even when a 3D format is set, the synchronization timing for the 3D Glasses may be inversed. Inverse the synchronization timing using Inverse 3D Glasses.s Signal - 3D Setup - Inverse 3D Glasses p.74 How a 3D image is perceived varies depending on the individual. When you start projecting a 3D image, a warning about viewing 3D images is displayed. You can turn off this warning by setting 3D Viewing Notice to Off. s Signal - 3D Setup - 3D Viewing Notice p.74 During 3D projection, the following Configuration menu functions cannot be changed. Aspect (set to Normal), Noise Reduction (set to Off), Overscan (set to Off), 4K Enhancement, Super-

resolution, Image Processing How the 3D image is viewed may change depending on the temperature of the surroundings and how long the lamp has been used. Refrain from using the projector if the image is not projected normally. 44 Useful Functions Using 3D Glasses You can view 3D images by using a pair of commercially available 3D Glasses (with an active shutter system that supports radio waves (RF/Bluetooth) communication system). To view 3D images, you first need to pair the 3D Glasses with the projector. See the User's Guide supplied with your 3D Glasses for more information. Warnings Regarding Viewing 3D Images Note the following important points when viewing 3D images. Caution Viewing Time When viewing 3D images, always take periodic breaks during extended viewing. Long periods of viewing 3D images may cause eye fatigue. The amount of time and frequency of such breaks varies from person to person. If your eyes still feel tired or uncomfortable even after taking a break from viewing, stop viewing immediately. Caution Watching 3D Images If your eyes feel fatigued or uncomfortable when viewing 3D images, stop viewing immediately. Continuing to view the 3D images could cause you to feel unwell. When viewing 3D images be sure to always wear 3D Glasses. Do not attempt to view 3D images without 3D Glasses. Doing so could cause you to feel unwell. Do not place any breakable or fragile objects around you when using 3D Glasses. 3D images may cause you to move your body involuntarily, resulting in damage to nearby items or personal injury. Only wear 3D Glasses when viewing 3D images. Do not move around while wearing 3D Glasses. Your vision may appear darker than normal, causing you to fall or injure yourself. Try to stay as level with the viewing screen as possible when viewing 3D images. Viewing 3D images at an angle reduces the 3D effect and may cause you to feel unwell due to unintended color changes. If using 3D Glasses in a room with fluorescent or LED lighting, you may see flashing or flickering throughout the room. If this should occur, reduce the lighting until the flickering goes away or turn off the lights completely when viewing 3D images. In some very rare cases, this flickering could trigger seizures or fainting for some individuals. If you begin to feel uncomfortable or unwell at any time when viewing 3D images, stop immediately. Stay at least three times the height of the screen away from the screen when viewing 3D images. The recommended viewing distance for an 80-inch screen is at least 3 meters, and at least 3.6 meters for a 100-inch screen. Sitting or standing any closer than the recommended viewing distance may result in eye fatigue. 45 Useful Functions Caution Health Risks You should not use 3D Glasses if you are sensitive to light, have a heart condition, or are unwell. Doing so could aggravate your pre-existing conditions. Caution Recommended Age of Use The minimum recommended age to view 3D images is six years old. Children under the age of six are still developing and viewing 3D images may cause complications. Consult your doctor if you have any concerns. Children viewing 3D images through 3D Glasses should always be accompanied by an adult. It is often difficult to tell when a child is feeling tired or uncomfortable, which could result in them feeling suddenly unwell. Always check with your child to ensure that they are not experiencing any eye fatigue during viewing. 46 Useful Functions Connecting with WirelessHD Installing the WirelessHD Transmitter You can use the supplied WirelessHD Transmitter to wirelessly receive image and sound data. This is useful when the projector cannot be setup near your AV devices as you can connect the devices to the projector without using cables. You can use the WirelessHD Transmitter in the following ways. You can connect up to four AV devices at the same time, and switch images using the remote control. As well as the projector, you can connect another monitor device, such as a television, to the HDMI Out port, and then switch the output using the remote control. This allows other monitor devices such as TVs connected to the HDMI Out port to project images from the connected AV device, even if the projector is off. You can connect smart devices and tablets that support MHL, and then project images from the connected MHL device. You can also operate MHL devices from the projector's remote control, as well as charge the MHL device. You can split the HDMI signal that is being input into the WirelessHD Transmitter into image and audio, and output to other devices. Even for AV devices that do not support HDCP 2.2, you can output audio by connecting to the HDMI Out port on the WirelessHD Transmitter. 47 Useful Functions WirelessHD Transmitter part names Front Rear Name a t button b c button button d Main power switch e AC adapter port f HDMI Out port g Optical Audio-Out port h HDMI Input port i 3D Glasses charging port j Setup button k On/Standby indicator

(blue) Function button for the WirelessHD Turns the transmitter on or off. This performs the same function as the Transmitter control on the lower section of the remote control. Changes to the image from each input port. This performs the same function as the Transmitter control on the lower section of the remote control. Switches the output image to the projector or the device connected to the HDMI Out port. This performs the same function as the Transmitter control on the lower section of the remote control. Turns the main power for the transmitter on or off. button for the WirelessHD button for the WirelessHD Connects the AC adapter. button on the remote control or the Connects to a monitor device, such as a television. You can switch the output image using the button on the WirelessHD Transmitter. Connects to an audio device equipped with an optical digital audio input port. Connects to the AV device you want to playback. You can switch the input image using the Input button. The HDMI4 port of the unit meets the MHL standards. You can play content from MHL compatible smart devices or tablets connected with an MHL ca-

ble. Connects a USB cable to charge the 3D Glasses. This is the button on the back of the WirelessHD Transmitter. This is a paring button for changing devices. Do not use this button under normal circumstances since this transmitter is already configured before the shipment. This flashes while the WirelessHD Transmitter is starting up, and remains lit while operating. 48 Useful Functions Name l WiHD indicator (blue) m Link indicator (blue) n TV indicator (blue) o HDMI1 to 4 indicators

(blue) Function Indicates the communication status for the WirelessHD. Lit when wirelessly transmitting images to the projector. Off when outputting to the HDMI Out port. Indicates the connection status with the projector. Turns on when connected to the projector. Flashes when searching for a projector. Flashes slowly when standing by in power saving status. Lit when a monitor device such as a TV is selected as the output. The indicator for the source currently being projected is lit. WirelessHD Transmitter connection example and signal flow c The antennas are built-into the front of the projector and the WirelessHD Transmitter. Make sure the antennas face each other (face the front) when setting up the devices. Also, do not place any object over the front side of the projector and WirelessHD Transmitter. Place the WirelessHD Transmitter on a level surface facing towards the projector. You can view the signal strength from the WirelessHD settings menu. s Settings - WirelessHD -

Video Reception p.75 When outputting audio from devices connected to the Optical Audio-Out port or the HDMI Out port, set the output audio in Audio Out Device. s p.61 You can output images from the projector or a monitor device such as TV. You can switch the output button on the remote control or the button on the WirelessHD When inputting images from HDMI Input1 or HDMI Input2 port, if noise is generated by monitors such as televisions or if the audio is lost, try connecting to the HDMI Input3 or HDMI Input4 port. This projector cannot transmit signals in the 18 Gbps transmission band such as 4K60p/4:4:4 using a image using the Transmitter.s p.59 wireless network. 49 Useful Functions Connection example 1: Viewing without an AV amplifier (audio is output from the Optical Audio-

Out port) Audio is output from the sound bar connected to the Optical Audio-Out port. Use a commercially available optical digital cable to connect to the sound bar. c When connecting a device, such as a sound bar, to the Optical Audio-Out port on the WirelessHD Transmitter, check that Audio Out Device is set to WiHD Transmitter (Optical). sSettings - HDMI Link - Audio Out Device p.75 The following conditions must be met when you want to output images from monitor devices including TVs that support 18 Gbps transmission band, such as 4k60p/4:4:4.

- Connect the monitor device to the HDMI Out port with a Premium HDMI cable.

- Connect the AV device to the HDMI Input1 or HDMI Input2 port. You cannot output some audio from the Optical Audio-Out port due to restrictions in audio standards*.

- Lossless audio

- Lossy high-bandwidth audio

- Immersive audio

* This is the specifications as of June 2018. This will be changed in the future. 50 Useful Functions Connection example 2: Viewing without an AV amplifier (audio is output from the HDMI Out port) Audio is output from the sound bar and so on connected to the HDMI Out port. In this situation, you can even output audio from AV amplifiers or sound bars that do not support HDCP 2.2. c When connecting a device, such as a sound bar, to the HDMI Out port on the WirelessHD Transmitter, check that Audio Out Device is set to WiHD Transmitter (HDMI). s Settings - HDMI Link - Audio Out Device p.75 51 Useful Functions Connection example 3: Viewing with a connected AV amplifier Connect using an AV amplifier. Audio is output from the AV amplifier. 52 Useful Functions Connection example 4: Viewing with a connected smart device Connect an MHL cable to the HDMI4 port. 53 Useful Functions Setting the WirelessHD Transmitter a Set up the WirelessHD Transmitter connected to the projector so that they are facing each other. s p.47 c The antennas are built-into the front of the projector and the WirelessHD Transmitter. Make sure the antennas face each other

(face the front) when setting up the devices. Also, do not place any object over the front side of the projector and WirelessHD Transmitter. Place the WirelessHD Transmitter on a level surface facing towards the projector. c Using an HDMI cable, connect the AV device you want to use to the Input port on the WirelessHD Transmitter. You can connect up to four multi-media players. b Connect the WirelessHD Transmitter to an electrical outlet using the supplied AC adapter. c You can connect another monitor device, such as a television, to the HDMI Out port on the WirelessHD The HDMI4 port of the WirelessHD Transmitter supports the MHL input signal. You can play content Transmitter. You can switch between output images using the remote control. s p.59 from MHL compatible smart devices or tablets connected with an MHL cable. If the following message is displayed when you connect an MHL device, the device has been connected to a port other than the HDMI4 port, or the connected device is not compatible with MHL.

"No Signal"

You can use the HDMI link function even when using the WirelessHD Transmitter. s p.61 Projecting Images a Start playback on the AV device, and then turn on the projector and the WirelessHD Transmitter. The On/Standby indicator on the WirelessHD Transmitter turns on. 54

 

 

Maintenance About PJLink PJLink was established by the JBMIA (Japan Business Machine and Information System Industries Association) as a standard protocol for controlling network-compatible projectors as part of their efforts to standardize projector control protocols. This projector complies with the PJLink Class2 standard established by the JBMIA. The port number used by the search function of PJLink is 4352 (UDP). You need to make network settings before you can use PJLink. See the following for more information on network settings. s p.82 It supports all commands defined by PJLink Class2 except for the following commands. The compliance is confirmed by the PJLink standard adaptability verification. URL:http://pjlink.jbmia.or.jp/english/

Non-compatible commands Mute settings Function Image muting set Audio muting set PJLink Command AVMT 11 AVMT 21 Correspondence table for port name and source number Port name Source number PC HDMI1 HDMI2 WirelessHD*

LAN

* EH-TW9400W/EH-TW8400W only 11 32 33 34 52 Manufacturer name displayed for "Manufacture name information query"

EPSON Model name displayed for "Product name information query"

EPSON TW9400/PC6050UB /H928A EPSON TW9400W EPSON TW8400/HC5050UB/H930A EPSON TW8400W/HC5050UBe/H931A 110 Appendix Optional Accessories and Consumables The following optional accessories/consumables are available for purchase if required. This list of optional accessories/consumables is current as of November 2018. Details of accessories are subject to change without notice. Varies depending on country of purchase. Optional Items Name Model No. Explanation Ceiling mount*

Ceiling pipe 450 (450 mm white)*

Ceiling pipe 700 (700 mm white)*

Cable cover Computer cable (1.8 m) Computer cable (3.0 m) Computer cable (20.0 m) Wireless LAN unit ELPMB22 ELPMB30 ELPFP13 ELPFP14 ELPCC05 ELPKC02 ELPKC09 ELPKC10 ELPAP10 Use when installing the projector on a ceiling. Use when installing the projector on a high ceil-

ing. Use this when installing the projector on a ceiling to cover the cables and improve the overall ap-

pearance. Do not attach the cable cover when the cable is secured with an HDMI cable clamp. Use when projecting a computer's screen. Use when connecting an external device to the projector via a wireless LAN to project images.

* Special expertise is required to suspend the projector from a ceiling. Contact your local dealer. Consumables Name Lamp unit Air filter Model No. ELPLP89 ELPAF39 Explanation Use as a replacement for used lamps. (1 lamp) Use as a replacement for used air filters. (1 air filter) 111 Appendix Supported Resolutions If the projector receives higher resolution signals than the resolution of the projector panel, the image quality may be degraded. The projector supports signals marked with a check symbol. PC Signal Format Resolution

(Dots) V Sync

(Hz) Dotclk

(MHz) Computer/BNC HDMI RGB RGB 4:4:4 YCbCr 4:2:2 4:2:0 8 10,12 8 10,12 8 10,12 8 10,12 640 800 1024 1280 1280 1366 1600 1280 1280 480 600 768 768 800 768 900 960 1024 60 60 60 60 60 60 60 60 60 25.175 40.000 65.000 79.500 83.500 85.500 108.000 108.000 108.000 VGA SVGA XGA WXGA WXGA++

SXGA SD Computer/BNC HDMI Signal Format Resolution

(Dots) V Sync

(Hz) Dotclk

(MHz) RGB RGB 4:4:4 YCbCr 4:2:2 4:2:0 8 10,12 8 10,12 8 10,12 8 10,12 SDTV (480i) SDTV (576i) SDTV (480p) SDTV (576p) 720 720 720 720 480 576 480 576 59.94 50 59.94 50 13.500 13.500 27.000 27.000 112 Appendix HD Signal Format Resolution

(Dots) V Sync

(Hz) Dotclk

(MHz) Computer/BNC HDMI RGB RGB 4:4:4 YCbCr 4:2:2 4:2:0 8 10,12 8 10,12 8 10,12 8 10,12 HDTV (720p) 1280 720 HDTV (1080i) 1920 1080 HDTV (1080p) 1920 1080 50 59.94 60 50 59.94 60 23.98 24 29.97 30 50 59.94 60 74.250 74.176 74.250 74.250 74.176 74.250 74.176 74.250 74.176 74.250 148.500 148.352 148.500

*2

*2

*2

*2

*1

*1

*1

*2

*2

*2

*2

*1

*1

*1

*2

*2

*2

*2

*1, 2

*1, 2

*1, 2

*1

*2 Signals from HDMI1/HDMI2 ports are supported. WirelessHD Transmitter supports pass-through only. HDR is supported. (For HDR, HDR10 and HLG are supported.) 4K Signal Format Resolution

(Dots) V Sync

(Hz) Dotclk

(MHz) Computer/BNC HDMI RGB RGB 4:4:4 YCbCr 4:2:2 4:2:0 8 10,12 8 10,12 8 10,12 8 10,12 3840x2160 3840 2160 4096x2160 4096 2160 23.98 24 25 29.97 30 50 59.94 60 50 59.94 60 23.98 24 25 29.97 30 50 59.94 60 50 59.94 60 296.703 297.000 297.000 296.703 297.000 297.000 296.703 297.000 594.000 593.407 594.000 296.703 297.000 297.000 296.703 297.000 297.000 296.703 297.000 594.000 593.407 594.000

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*2

*1, 2

*1, 2

*1, 2

*2

*2

*2

*2

*2

*1, 2

*1, 2

*1, 2

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1, 2, 3

*1, 2, 3

*1, 2, 3

*1, 2, 3

*1, 2, 3

*1, 2, 3

*1 Signals from HDMI1/HDMI2 ports are supported. WirelessHD Transmitter supports pass-through only. 113 Appendix

*2

*3 HDR is supported. (For HDR, HDR10 and HLG are supported.) Signals from HDMI1/HDMI2 ports are supported. Signals from WirelessHD Transmitter are converted from 4:2:0 to 4:2:2. 3D Signal Format Resolution

(Dots) V Sync

(Hz) Dotclk

(MHz) 3D Format RGB 4:4:4 HDMI YCbCr 4:2:2 4:2:0 8 10,12 8 10,12 8 10,12 8 10,12 HDTV (720p) 1280 720 60 HDTV (720p) 1280 720 59.94 HDTV (720p) 1280 720 50 HDTV (1080i) 1920 1080 60 HDTV (1080i) 1920 1080 59.94 HDTV (1080i) 1920 1080 50 HDTV (1080p) 1920 1080 24 HDTV (1080p) 1920 1080 23.98 HDTV (1080p) 1920 1080 60 HDTV (1080p) 1920 1080 59.94 HDTV (1080p) 1920 1080 50 148.500 74.250 74.250 148.500 74.250 74.250 148.500 74.250 74.250 148.500 74.250 74.250 148.500 74.250 74.250 148.500 74.250 74.250 148.500 74.250 74.250 148.500 74.250 74.250 297.000 148.500 148.500 297.000 148.500 148.500 297.000 148.500 148.500 Frame Packing Side by Side Top and Bottom Frame Packing Side by Side Top and Bottom Frame Packing Side by Side Top and Bottom Frame Packing Side by Side Top and Bottom Frame Packing Side by Side Top and Bottom Frame Packing Side by Side Top and Bottom Frame Packing Side by Side Top and Bottom Frame Packing Side by Side Top and Bottom Frame Packing Side by Side Top and Bottom Frame Packing Side by Side Top and Bottom Frame Packing Side by Side Top and Bottom

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1 Signals from HDMI1/HDMI2 ports are supported. WirelessHD Transmitter supports pass-through only. 114 Appendix 3D Input Signals MHL (via a WirelessHD Transmitter*) Signal Refresh Rate

(Hz) Resolution (dots) HDTV (720p) HDTV (1080i) HDTV (1080p) HDTV (1080p)

* HDMI4 port only 50/60 50/60 50/60 24 1280 x 720 1920 x 1080 1920 x 1080 1920 x 1080 WirelessHD Input Signal MHL*

3D Format Side by Side Top and Bot-

tom

-

-

-

Frame Pack-

ing

-

-

-

-

Signal Refresh Rate (Hz) Resolution (dots) SDTV (480i) SDTV (576i) SDTV (480p) SDTV (576p) HDTV (720p) HDTV (1080i) HDTV (1080p) 4K x 2K

* HDMI4 port only 60 50 60 50 50/60 50/60 24/30/50/60 24/25/30 720 x 480 720 x 576 720 x 480 720 x 576 1280 x 720 1920 x 1080 1920 x 1080 3840 x 2160 115 Appendix Specifications Product name H928A/H929A/H931A/EH-TW9400/EH-TW8400W/EH-TW8400 Pro Cinema 6050UB/Home Cinema 5050UBe/Home Cinema 5050UB Appearance Panel Size Display method Resolution Focus adjustment Zoom adjustment Lamp (light source) Lamp replacement time Power supply Power con-

sumption 100 to 120 V area 220 to 240 V area Operating altitude Operating temperature Storage temperature Mass Connec-

tors PC port HDMI port RS-232C port Trigger Out port LAN port Service port*

USB-A port *

USB port (for Opt.HDMI power supply)*

520 (W) x 170 (H) x 450 (D) mm (not including adjustable foot) 0.74" wide Polysilicon TFT active matrix 1920 (W) x 1080 (H) x 3 Motorized Motorized (Approx. 1 to -2.1) UHE lamp 250 W, Model No.: ELPLP89 3400 hours 100 - 240 V AC 10%, 50/60 Hz, 3.8 - 1.7 A Rated power consumption: 373 W Standby power consumption (Communication On): 2.0 W Standby power consumption (Communication Off): 0.3 W Rated power consumption: 355 W Standby power consumption (Communication On): 2.0 W Standby power consumption (Communication Off): 0.3 W Altitude 0 to 3048 m

+5 to +35C (No condensation) (at an altitude of 0 to 2286 m)

+5 to +30C (No condensation) (at an altitude of 2287 to 3048 m)

-10 to +60C (No condensation) Approx. 11 kg Mini D-Sub15-pin (female) blue HDMI HDCP2.2 supported,CEC signals supported, 3D signals supported, Deep Color Mini D-Sub 9-pin (male) Stereo mini jack (3.5) RJ-45 USB connector (Type B) USB connector (Type A) 1 2 1 1 1 1 1 1

* Supports USB 2.0. However, USB ports are not guaranteed to operate all devices that support USB. This product is also designed for IT power distribution system with phase-to-phase voltage 230V. 116 Appendix Angle of tilt If you use the projector tilted at an angle of more than 3, the projector could be damaged or it may lead to an accident. 117 Appendix Appearance 520 260 a

. 7 2 9 1 a b Center of lens Distance from center of lens to suspension bracket fixing point 434 LENS 67

. 6 0 6 1 0 6 0 5 4 0 6 1 Units: mm

. 1 6 9 6 6

. M4x9

. 6 9 4 5 7 5 8

. 0 6 1 150 300 110 119 Appendix List of Safety Symbols The following table lists the meaning of the safety symbols labeled on the equipment. Symbol mark Approved stand-

ards Meaning IEC60417 No. 5007 IEC60417 No. 5008 IEC60417 No. 5009 ISO7000 No. 0434B IEC3864-B3.1 IEC60417 No. 5041 IEC60417 No. 6042 ISO3864-B3.6 IEC60417 No. 5957 IEC60417 No. 5926

---

IEC60417 No. 5001B IEC60417 No. 5002

---

IEC60417 No. 5019 IEC60417 No. 5017

"ON" (power) To indicate connection to the mains.

"OFF" (power) To indicate disconnection from the mains. Stand-by To identify the switch or switch position by means of which part of the equipment is switched on in order to bring it into the stand-

by condition. Caution To identify general caution when using the product. Caution, hot surface To indicate that the marked item can be hot and should not be touched without taking care. Caution, risk of electric shock To identify equipment that has risk of electric shock. For indoor use only To identify electrical equipment designed primarily for indoor use. Polarity of d.c. power connector To identify the positive and negative connections (the polarity) on a piece of equipment to which a d.c. power supply may be connected. Battery, general On battery powered equipment. To identify a device for instance a cover for the battery compartment, or the connector terminals. Positioning of cell To identify the battery holder itself and to identify the positioning of the cell(s) inside the battery holder. Protective earth To identify any terminal which is intended for connection to an external conductor for protection against electric shock in case of a fault, or the terminal of a protective earth electrode. Earth To identify an earth (ground) terminal in cases where neither the symbol is explicitly required. 120 Appendix Symbol mark Approved stand-

ards Meaning IEC60417 No. 5032 IEC60417 No. 5031 IEC60417 No. 5172 ISO 3864 ISO 3864

---

---

ISO3864 IEC60825-1 ISO 3864 Alternating current To indicate on the rating plate that the equipment is suitable for alternating current only; to identify relevant terminals. Direct current To indicate on the rating plate that the equipment is suitable for direct current only; to identify relevant terminals. Class II equipment To identify equipment meeting the safety requirements specified for Class II equipment according to IEC 61140. General prohibition To identify actions or operations that are prohibited. Contact prohibition To indicate injury that could occur due to touching a specific part of the equipment. Never look into the projection lens while the projector is on. To indicate that the marked item don't place anything on pro-

jector. Caution, laser radiation To indicate the equipment has a laser radiation part. Disassembly prohibition To indicate a risk of injury, such as electric shock, if the equipment is disassembled. IEC60417 No. 5266 Standby, partial standby To indicate that part of the equipment is in the ready status. ISO3864 IEC60417 No. 5057 IEC 60417-6056 IEC 60417-6043

--

Caution, movable parts To indicate that you must keep away from movable parts ac-

cording to protection standards. Caution (movable fan blades) To indicate that you must keep away from the blades of the mov-

able fan according to protection standards. Caution (sharp corners) To indicate that you must not touch the sharp corners of the product according to protection standards. Never look into the projection lens while the projector is on. 121 Appendix Glossary This section briefly explains the difficult terms that are not explained in context in the text of this guide. For details, refer to other commercially available publications. Aspect Ratio HDCP HDMI HDTV Interlace MHL Pairing SDTV SVGA SXGA VGA XGA YCbCr YPbPr The ratio between an image's length and its height. Screens with a horizontal:vertical ratio of 16:9, such as HDTV screens, are known as wide screens. SDTV and general computer displays have an aspect ratio of 4:3. HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to pre-

vent illegal copying and protect copyrights by encrypting digital signals sent over DVI and HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital images protected by HDCP technology. However, the projector may not be able to project images protected with updated or revised versions of HDCP encryption. An abbreviation for High Definition Multimedia Interface. This is the standard by which HD images and multichannel audio signals are digitally transmitted. HDMI is a standard aimed at digital consumer electronics and computers. By not com-

pressing the digital signal, the image can be transferred at the highest quality possible. It also provides an encryption function for the digital signal. An abbreviation for High-Definition Television. This refers to high-definition systems which satisfy the following conditions. Vertical resolution of 720p or 1080i or greater (p = Progressive, i = Interlace) Screen aspect of 16:9 Dolby Digital audio reception and playback (or output) Transmits information needed to create one screen by sending every other line, starting from the top of the image and working down to the bottom. Images are more likely to flicker because one frame is displayed every other line. An abbreviation for Mobile High-definition Link, which is a standard high-definition in-

terface that enables high-speed transfer of video signals on mobile devices. It is a standard targeting smartphones and tablets that transfers uncompressed digital signals without loss of quality and also enables simultaneous charging of such devices. Register devices in advance when connecting with Bluetooth devices to ensure mutual communication. An abbreviation for Standard Definition Television. This refers to standard television sys-

tems which do not satisfy the conditions for HDTV High-Definition Television. A screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots. A screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots. A screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots. A screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots. In component image signals for SDTV, Y is the brightness, while Cb and Cr indicate the color difference. In component image signals for HDTV, Y is the brightness, while Pb and Pr indicate the color difference. 122 Appendix General Notes All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the infor-

mation contained herein. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Prod-

ucts by Seiko Epson Corporation. The contents of this guide may be changed or updated without further notice. Illustrations in this guide and the actual projector may differ. Restriction of Use When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc; or functional/

precision devices etc, you should use this product only after giving consideration to including fail-safes and redundancies into your design to maintain safety and total system reliability. Because this product was not intended for use in applications requiring extremely high reliability/safety such as aerospace equipment, main communication equipment, nuclear power control equipment, or medical equipment related to direct medical care etc, please make your own judgment on this products suitability after a full evaluation. Warning Labels Warning This product comes with warning labels. As with any bright source, do not stare into the beam, RG2 IEC/EN 62471-5:2015. 123 Appendix General Notice

"EPSON" is a registered trademark of Seiko Epson Corporation. "EXCEED YOUR VISION" and "ELPLP" are registered trademarks or trademarks of Seiko Epson Corporation. Mac, OS X and iOS are trademarks of Apple Inc. Windows and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licen-

singLLC. The Bluetooth word mark and logo are registered trademarks of Bluetooth SIG, Inc., and the Seiko Epson Cor-

poration uses these marks under license. Other trademarks or trade names are the property of their respective owners. Bluetopia is provided for your use by Stonestreet One, LLC under a software license agreement. Stonestreet One, LLC is and shall remain the sole owner of all right, title and interest whatsoever in and to Bluetopia and your use is subject to such ownership and to the license agreement. Stonestreet One, LLC reserves all rights related to Bluetopia not expressly granted under the license agreement and no other rights or licenses are granted either directly or by implication, estoppel or otherwise, or under any patents, copyrights, mask works, trade secrets or other intellectual property rights of Stonestreet One, LLC. 2000-2012 Stonestreet One, LLC All Rights Reserved. WPA and WPA2 are registered trademarks of Wi-Fi Alliance. App Store is a service mark of Apple Inc. Android and Google Play are trademarks of Google LLC.

"QR Code" is a registered trademark of DENSO WAVE INCORPORATED.

"CINEMASCOPE" is a registered trademark of Twentieth Century Fox Film Corporation. Other product names used herein are also for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. SEIKO EPSON CORPORATION 2018. All rights reserved. Indication of the manufacturer and the importer in accordance with requirements of directive 2011/65/

EU (RoHS) Manufacturer: SEIKO EPSON CORPORATION Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan Telephone: 81-266-52-3131 http://www.epson.com/

Importer: SEIKO EUROPE B.V. Address: Azi building, Atlas ArenA, Hoogoorddreef 5, 1101 BA Amster-

dam Zuidoost The Netherlands Telephone: 31-20-314-5000 http://www.epson.eu/

124 Index 3 A B C 3D brightness ................................................. 74 3D display ......................................................... 74 3D format ......................................................... 74 3D Glasses ........................................................ 45 3D Glasses charging port ........................... 48 3D images ........................................................ 44 3D settings ....................................................... 74 3D viewing notice ......................................... 74 Adjust focus ..................................................... 29 Adjusting RGB ................................................. 38 Adjusting the focus ...................................... 29 Adjusting the tilt ............................................ 31 Advanced .................................................. 73, 75 Air filter ........................................................... 100 Air filter cover ............................................... 100 Air filter replacement period .................. 102 AMX Device Discovery ................................. 85 Appearance ................................................... 119 Aspect ......................................................... 33, 74 Auto iris ...................................................... 36, 73 Auto setup ....................................................... 74 Basic menu ....................................................... 83 Blanking ............................................................ 75 Brightness .......................................... 38, 72, 73 CEC standards ................................................. 61 Channel

............................................................. 83 Child lock .......................................................... 77 Cleaning the air filter ................................. 100 Cleaning the lens ........................................ 102 Cleaning the main unit ............................. 101 Color Depth ..................................................... 86 Color Format ................................................... 86 Color mode ............................................... 32, 72 Color saturation ............................................. 72 Color Space ...................................................... 75 Color Temp. .................................................... 72 Color Uniformity ................................... 79, 108 Configuration menu ..................................... 71 Connected Device .................................. 56, 76 Connecting ...................................................... 19 Connecting a computer .............................. 20 Connecting to the Trigger Out port ....... 20 Connecting video equipment ........... 19, 21 Connection Mode ......................................... 83 D E F G H I Contrast ............................................................ 72 Control Panel

..................................................... 7 Control panel lock ......................................... 77 Control4 SDDP ................................................ 85 Cool-down ....................................................... 27 DHCP .................................................................. 84 Direct power on ............................................. 80 Display ............................................................... 79 Display Background ..................................... 79 Display LAN Info. .......................................... 83 Display the QR Code .................................... 82 Displaying the test pattern ........................ 28 Dynamic Range .............................................. 75 Error/Warning indicators ............................ 87 Event ID ............................................................. 98 Extended menu .............................................. 78 Fine Line Adjust ...................................... 35, 73 Focus .................................................................. 92 Frame Interpolation ..................................... 72 Frame interpolation ..................................... 36

...................................................................... 33 Full Gain ............................................................. 38, 73 Gamma .............................................................. 40 Gateway Address ........................................... 84 HDMI 1 to 4 indicators ................................. 48 HDMI Link ......................................................... 76 HDMI link .......................................................... 61 HDMI port ......................................................... 61 High altitude mode ...................................... 80 Home Screen ................................................... 78 Home screen ................................................... 26 Hue .............................................................. 38, 73 Illumination ..................................................... 80 Image ................................................................. 32 Image Enhancement .................................... 73 Image enhancement .................................... 35 Image menu .................................................... 72 Indicators .......................................................... 87 Info menu ......................................................... 86 125 Index Inverse 3D Glasses ......................................... 74 IP Address ......................................................... 84 IP Address Display ......................................... 84 IP Settings ........................................................ 84 Projection ......................................................... 79 Projection size ................................................ 29 Projector Info .................................................. 86 Projector name ............................................... 83 K L M N O P Keystone .................................................... 31, 75 Keystone distortion ...................................... 31 Lamp cover ............................................... 6, 104 Lamp cover fixing screw ........................... 104 Lamp replacement period ....................... 102 LAN port ............................................................ 21 Language ......................................................... 81 Lens shift .......................................................... 30 Link indicator .................................................. 48 Load Lens Position ........................................ 78 Load memory .................................................. 42 Lock setting ..................................................... 77 Memory ............................................................. 78 Memory function ........................................... 42 Menu .................................................................. 71 Messages .......................................................... 79 Model Name .................................................... 79 Network information ................................... 82 Network menu ............................................... 82 Noise .................................................................. 92 Offset .......................................................... 38, 73 On/Standby indicator .................................. 48 Operating range ............................................ 24 Operating time ............................................ 105 Operation ......................................................... 80 Others menu ................................................... 85 Overscan ........................................................... 74 Panel Alignment ............................ 79, 81, 106 Passphrase ....................................................... 84 PJLink .............................................................. 110 PJLink Password ............................................. 83 Position ............................................................. 74 Power ................................................................. 27 Power consumption ..................................... 73 Power supply .................................................. 25 126 R S T

................................................ 9 Remote Control Remote control

.............................................. 23 Remote Password .......................................... 83 Replacement periods for consumables

............................................................................. 102 Replacement time ...................................... 102 Replacing consumables ........................... 102 Replacing the air filter ............................... 102 Replacing the lamp .................................... 103 Reset ....................................... 73, 75, 76, 78, 81 Reset all

............................................................. 86 Reset lamp hours ................................. 86, 105 Reset Lens Position ....................................... 86 Reset memory ................................................. 86 Reset menu ............................................... 85, 86 RGBCMY ..................................................... 38, 73 Saturation .................................................. 38, 73 Save Lens Position ........................................ 78 Save memory .................................................. 42 Search Access Point ...................................... 84 Security ............................................................. 84 Security menu ................................................ 84 Settings menu ................................................ 75 Sharpness .................................................. 34, 72 Signal menu .................................................... 74 Sleep mode ...................................................... 80 Soft Focus Detail

..................................... 35, 73 Soft Keyboard ................................................. 83 Source ................................................................ 26 Specifications ............................................... 116 SSID .................................................................... 83 SSID Display ..................................................... 84 Standby Mode ................................................ 80 Startup Screen ................................................ 79 Sub menu ......................................................... 71 Subnet Mask .................................................... 84 Supported resolutions .............................. 112 Sync. .................................................................. 74 Tint ...................................................................... 72 Top menu ......................................................... 71 Tracking ............................................................ 74 Transmission range ...................................... 57 Index U V W Z TV indicator ..................................................... 48 User button ...................................................... 77 Version .............................................................. 86 Video Reception ..................................... 56, 76 WiHD indicator ............................................... 48 Wired LAN menu ........................................... 84 Wireless LAN menu ....................................... 83 Wireless LAN Power ...................................... 82 WirelessHD ................................................ 47, 76 Zoom .................................................................. 33 Zoom adjustment ......................................... 29 127

 

 

Declaration of Conformity According to 47CFR, Part 2 and 15, Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We:

Located at:

Telephone:

Epson America, Inc. 3840 Kilroy Airport Way, MS 3-13, Long Beach, CA 90806

(562) 981-3840 E n g l i s h Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47CFR 2.906. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Trade Name:

Type of Product:

Model:

Epson LCD Projector H931A Bluetooth and WirelessHD Safety and Specifications LCD Projector Contains Bluetooth module model: DBUB-E207 (Projector) This document provides safety instructions and describes the specifications. Read this document carefully before use to ensure your safety and product performance. U.S. FCC Notices FCC ID: BKMAE-H931RX Contains FCC ID: BKMAE-E207 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This antenna of this device must not be co-located or used in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. Properly shielded cables must be used for connections to LCD Projector in order to meet FCC emission limits. The cable for peripheral with a ferrite core must be used for RF interference suppression. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of at least 7.9 inches (20 cm) between the radiator and your body. Canada Industry Canada (IC) Notices IC: 1052D-H931RX Contains IC: 1052D-E207 This Class B digital apparatus complies with Canadian ICES-003. CAN ICES-3(B)/NMB-3(B) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. This device and its antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-transmitter product procedures. Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm (7.9 inches) between the radiator and your body. This equipment is not permitted for use on aircraft or satellites. Epson America, Inc. Limited Warranty Two-Year Projector and WirelessHD Transmitter Limited Warranty, 90-Day Lamp Limited Warranty What Is Covered: Epson America, Inc. (Epson) warrants to the original retail purchaser of the Epson projector product enclosed with this limited warranty statement that the product, if purchased new and operated in the United States, Canada, or Puerto Rico will be free from defects in workmanship and materials for a period of two (2) years from the date of original purchase. This limited warranty applies only to the projector and the WirelessHD Transmitter and not to the projector lamp. The projector lamp carries a limited warranty period of ninety (90) days from the date of original purchase. For warranty service, you must provide proof of the date of original purchase. What Epson Will Do To Correct Problems: If your product requires service during the limited warranty period, please call Epson at the number on the bottom of this statement and be prepared to provide the model, serial number, and date of original purchase. Epson will, at its option, repair or replace the defective unit, without charge for parts or labor. If Epson authorizes an exchange for the defective projector, Epson will ship a replacement projector to you, freight prepaid, so long as you use an address in the United States, Canada, or Puerto Rico. You are responsible for securely packaging the defective unit and returning it to Epson within five (5) working days of receipt of the replacement. Epson requires a debit or a credit card number to secure the cost of a replacement projector in the event that you fail to return the defective one. When Epson authorizes an exchange for defective WirelessHD, you must first send in the defective transmitter to Epson. Once we have received your defective transmitter Epson will ship a replacement product to you, freight prepaid, so long as you use an address in the United States, Canada, or Puerto Rico. If Epson authorizes repair instead of exchange, Epson will direct you to send your product to Epson or its authorized service center, where the product will be repaired and sent back to you. You are responsible for packing the product and for all costs to and from the Epson authorized service center. When warranty service involves the exchange of the product or of a part, the item replaced becomes Epson property. The exchanged product or part may be new or refurbished to the Epson standard of quality, and at Epsons option, the replacement may be another model of like kind and quality. Epsons liability for replacement of the covered product will not exceed the original retail selling price of the covered product. Exchange or replacement products or parts assume the remaining warranty period of the product covered by this limited warranty. If Epson replaces the lamp as part of the warranty service, the replacement lamp carries the limited 90-day warranty stated above. What This Warranty Does Not Cover: This warranty covers only normal use in the United States, Canada or Puerto Rico. Excessive continual use is not considered normal use. This warranty does not cover consumables such as filters. This warranty is not transferable. Epson is not responsible for warranty service should the Epson label or logo or the rating label or serial number be removed. Epson is not responsible for warranty service should the product fail to be properly maintained or fail to function properly as a result of misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters such as fire, flood, and lightning, improper electrical current, software problems, the use of non-Epson lamps, add-in cards or cables, interaction with non-Epson products, or service other than by Epson or an Epson Authorized Servicer. Postage, insurance, or shipping costs incurred in presenting your Epson product for carry-in warranty service are your responsibility. If a claimed defect cannot be identified or reproduced in service, you will be held responsible for costs incurred. DISCLAIMER OF WARRANTIES: THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED OR IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATION MADE BY ANY OTHER PERSON OR FIRM ARE VOID. Remedies: Your exclusive remedy and Epsons entire liability for a material breach of this Agreement will be limited to a refund of the price paid for the Epson products covered by this Agreement. Any action for breach of warranty must be brought within 3 months of the expiration date of the warranty. Epson is not liable for performance delays or for nonperformance due to causes beyond its reasonable control. Except as provided in this written warranty, neither Epson nor its affiliates shall be liable for any loss, inconvenience, or damage, including direct, special, incidental or consequential damages, including lost profits, cost of substitute equipment, downtime, claims of third parties, including customers, or injury to property, resulting from the use or inability to use the Epson product, whether resulting from a breach of warranty or any other legal theory. Some jurisdictions do not allow limits on warranties or remedies for breach in certain transactions. In such jurisdictions, the limits in this paragraph and the preceding paragraph may not apply. Arbitration, Governing Laws: Any disputes arising out of this Agreement will be settled by arbitration to be conducted before a single arbitrator in Los Angeles, California, in accordance with the commercial Arbitration Rules of the American Arbitration Association, and judgment upon the award rendered by the arbitrator may be entered in any court having jurisdiction thereof. This Agreement shall be construed in accordance with the laws of the State of California, except this arbitration clause which shall be construed in accordance with the Federal Arbitration Act. In Canada, warranties include both warranties and conditions. To find the Epson Authorized Reseller nearest you, please visit our website at: www.epson.com. To find the Epson Customer Care Center nearest you, please visit www.epson.com/support. To contact the Epson ConnectionSM, please call (800) 637-7661 or (562) 276-4394 in the U.S. and (905) 709-3839 in Canada or write to Epson America, Inc., P.O. Box 93012, Long Beach, CA 90809-3012. Dclaration de conformit F r a n a i s Selon la norme 47CFR, parties 2 et 15, rgissant les ordinateurs personnels et priphriques de classe B, et/

ou les units centrales et les dispositifs dalimentation lectrique utiliss avec les ordinateurs personnels de classe B :

Nous :

Situs :

Tlphone :

Epson America, Inc. 3840 Kilroy Airport Way, MS 3-13, Long Beach, CA 90806 1 562 981-3840 Dclarons sous notre seule et unique responsabilit que le produit identifi dans la prsente est conforme la norme 47CFR, parties 2 et 15, des rgles FCC rgissant les dispositifs numriques de classe B. Chaque produit commercialis est identique lappareil reprsentatif test et jug conforme aux normes. Les dossiers indiquent que lquipement produit se situe dans les limites acceptables, du fait de la production en quantit et des essais statistiques raliss, conformment au rglement 47CFR, alina 2.909. Lutilisation est soumise aux deux conditions suivantes : 1) cet appareil ne doit pas provoquer dinterfrences nfastes, et 2) cet appareil doit tolrer les interfrences reues, y compris celles qui risquent de provoquer un fonctionnement indsirable. Nom commercial : Epson Type de produit : Projecteur ACL Modle :

H931A Consignes de scurit et caractristiques du module Bluetooth et du module WirelessHD Projecteur ACL Contient un module Bluetooth de modle : DBUB-E207 (pour projecteur) Ce document contient des consignes de scurit et une description des caractristiques. Lisez attentivement ce document avant lutilisation pour assurer votre scurit ainsi que le rendement optimal du produit. -U. Avis FCC FCC ID : BKMAE-H931RX Contient FCC ID : BKMAE-E207 Cet appareil est conforme la partie 15 de la rglementation FCC. Lutilisation de lappareil doit seffectuer selon deux conditions : 1) cet appareil ne doit pas provoquer dinterfrences nfastes, et 2) cet appareil doit tolrer les interfrences reues, y compris celles qui risquent de provoquer un fonctionnement indsirable. lissue des tests dont il a fait lobjet, cet appareil a t dclar conforme aux normes des appareils numriques de classe B, conformment la partie 15 de la rglementation FCC. Ces normes sont destines assurer un niveau de protection raisonnable contre les interfrences nfastes dans les installations rsidentielles. Cet appareil produit, utilise et peut mettre des frquences radiolectriques et, sil nest pas install ou utilis conformment aux directives, peut brouiller les ondes radio ou tlvisuelles. Toutefois, il est impossible de garantir quaucune interfrence ne se produira dans une installation particulire. Si cet quipement brouille la rception des ondes radio et tlvisuelles, ce que vous pouvez dterminer en teignant et en rallumant lquipement, nous vous encourageons prendre lune ou plusieurs des mesures correctives suivantes :

Rorientez ou dplacez lantenne rceptrice. loignez lappareil du rcepteur. Branchez lappareil dans une autre prise ou dans un autre circuit que celui du rcepteur. Demandez conseil au revendeur de lappareil ou un technicien radio/tlvision expriment. Mise en garde : Toute modification non expressment autorise par la partie responsable de la conformit peut annuler la permission dutilisation du matriel. Lantenne de cet appareil ne doit pas tre installe au mme endroit quune autre antenne ou un autre transmetteur ou utilise conjointement une autre antenne ou un autre transmetteur sauf en cas de conformit aux procdures FCC en matire dappareils multi-transmetteurs. Des cbles blinds doivent tre utiliss pour la connexion au projecteur ACL afin de respecter les limites dmission FCC. Le cble de priphrique contenant un noyau magntique doit tre utilis pour la suppression des interfrences RF. Dclaration dexposition aux radiations de la FCC :

Cet quipement est conforme aux limites dexposition aux rayonnements de la FCC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 7,9 po

(20 cm) de distance entre la source de rayonnement et votre corps. Canada Avis dIndustrie Canada (IC) IC : 1052D-H931RX Contient IC : 1052D-E207 Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. CAN ICES-3 (B)/NMB-3 (B) Cet appareil est conforme aux normes CNR exemptes de licence dIndustrie Canada. Lutilisation est soumise aux deux conditions suivantes : 1) cet appareil ne doit pas provoquer dinterfrences nfastes, et 2) cet appareil doit tolrer les interfrences reues, y compris celles qui risquent de provoquer un fonctionnement indsirable. Cet appareil et ses antennes ne doivent pas tre installs au mme endroit quune autre antenne ou un autre transmetteur ou utiliss conjointement une autre antenne ou un autre transmetteur sauf en cas de conformit aux procdures dIC en matire dappareils multi-transmetteurs. Dclaration dexposition aux radiations :

Cet quipement est conforme aux limites dexposition aux rayonnements dIC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 7,9 po

(20 cm) de distance entre la source de rayonnement et votre corps. Cet quipement ne peut tre utilis bord dun avion ou dun satellite. Garantie limite dEpson America, Inc. Garantie limite de deux ans sur le projecteur et sur le transmetteur WirelessHD et garantie limite de 90 jours sur la lampe. lments couverts par la garantie : Epson America, Inc. ( Epson ) garantit lacheteur original du produit Epson couvert par la prsente garantie limite que le produit, sil est achet ltat neuf et utilis au Canada, aux tats-Unis ou Puerto Rico, sera exempt de dfauts de fabrication et de vices de matriau pendant une dure de deux (2) ans compter de la date dachat dorigine. Cette garantie limite sapplique seulement au projecteur et au transmetteur WirelessHD. Elle ne sapplique pas la lampe du projecteur. La lampe comporte une garantie limite de quatre-vingt-dix (90) jours compter de la date dachat dorigine. Pour toute intervention au titre de la garantie, vous devez fournir la preuve de la date dachat dorigine. Ce que fera Epson pour remdier aux problmes : Si votre produit doit tre rpar durant la priode o il est couvert par la garantie limite, veuillez appeler Epson au numro inscrit dans le bas de cette dclaration et assurez-vous dtre en mesure dindiquer le modle, le numro de srie et la date dachat dorigine. Epson pourra, son choix, rparer ou remplacer lappareil dfectueux sans frais de pices ou de main-doeuvre. Si Epson autorise le remplacement du projecteur dfectueux, Epson vous enverra un produit de remplacement, en port pay si vous avez une adresse au Canada, aux tats-Unis ou Puerto Rico. Il vous incombe demballer correctement lappareil dfectueux et de le retourner Epson dans un dlai de cinq (5) jours ouvrables aprs avoir reu lunit de remplacement. Epson vous demandera un numro de carte de crdit ou de dbit pour couvrir le cot du projecteur de remplacement au cas o vous ne retourneriez pas le produit dfectueux. LorsquEpson autorise le remplacement du transmetteur WirelessHD dfectueux, vous devez dabord retourner le transmetteur dfectueux Epson. Une fois que nous aurons reu le transmetteur dfectueux, Epson vous enverra un produit de remplacement, en port pay si vous avez une adresse au Canada, aux tats-Unis ou Puerto Rico. Pour une rparation du produit, Epson vous demandera de lui envoyer ce dernier directement ou son centre de service autoris qui rparera le produit et vous le renverra. Vous avez la responsabilit demballer le produit et devez dfrayer les cots dexpdition vers et depuis le centre de service autoris Epson. Lorsquune intervention au titre de la garantie ncessite lchange du produit ou dune pice, larticle remplac devient proprit dEpson. Le produit ou la pice de remplacement pourra tre neuf ou remis neuf selon les normes de qualit dEpson et, au choix dEpson, pourra tre un autre modle de mme type et qualit. La responsabilit dEpson pour le remplacement du produit couvert par la prsente garantie ne peut dpasser le prix de vente dorigine du produit couvert. Les produits ou pices remplacs sont couverts pour la priode de garantie restante du produit dorigine couvert par la prsente garantie limite. Si Epson remplace la lampe lors dune intervention au titre de la garantie, la lampe de rechange porte la garantie limite de 90 jours nonce plus haut. lments non couverts par la garantie : Cette garantie suppose lutilisation normale du produit au Canada, aux tats-Unis ou Puerto Rico. Une utilisation excessive ou continue nest pas considre comme une utilisation normale. Cette garantie ne couvre pas les consommables tels que les filtres. Cette garantie nest pas transfrable. Epson ne sera pas tenue deffectuer dinterventions au titre de la garantie lorsque ltiquette ou le logo Epson, le numro de srie ou la plaque signaltique ont t enlevs de lappareil. Epson ne sera pas tenue deffectuer dinterventions au titre de la garantie si le produit nest pas correctement entretenu ou ne fonctionne pas correctement du fait dune utilisation inadquate ou abusive, dune installation incorrecte, dune ngligence, davaries lors du transport, de dommages causs par des dsastres tels un incendie, une inondation ou la foudre, dune surtension lectrique, de problmes logiciels, dune interaction avec des produits dune autre marque quEpson, ou dune intervention effectue par un tiers autre quun rparateur Epson agr ou Epson. Les frais daffranchissement, dassurance ou dexpdition engags pour faire rparer votre produit Epson au titre de la garantie avec retour en atelier seront votre charge. Si une anomalie signale ne peut tre dcele ni reproduite lors de lentretien, les frais engags seront votre charge. STIPULATION DEXONRATION DE GARANTIES : CE QUI PRCDE CONSTITUE LA SEULE GARANTIE ET EXCLUT TOUTE AUTRE GARANTIE, EXPRESSE OU IMPLICITE, Y COMPRIS, MAIS SANS SY LIMITER, TOUTE GARANTIE IMPLICITE DE QUALIT MARCHANDE, DAPTITUDE UNE FIN PARTICULIRE ET DE NON-VIOLATION DE DROITS. SAUF DISPOSITIONS CONTRAIRES, TOUTE DCLARATION OU GARANTIE FAITES PAR UNE AUTRE PERSONNE OU SOCIT EST NULLE. Recours : Votre recours exclusif et lentire responsabilit dEpson en cas de violation substantielle de cette entente seront limits un remboursement du prix pay pour les produits Epson couverts par la prsente entente. Toute action au titre de la garantie doit intervenir dans les 3 mois compter de la date dexpiration de la garantie. Epson ne sera pas tenue responsable des retards ou des priodes de non-fonctionnement en raison de causes indpendantes de sa volont. Sauf dispositions contraires dans la prsente garantie crite, Epson et ses filiales ne peuvent tre tenues responsables des pertes, inconvnients ou dommages, incluant des dommages directs, particuliers, conscutifs ou indirects, incluant la perte de bnfices, les cots de lquipement de substitution, le temps darrt, les rclamations des tiers, incluant les clients, ou les dommages matriels rsultant de lutilisation ou de limpossibilit dutiliser le produit Epson, quelle soit cause par une violation de la garantie ou toute autre thorie juridique. Certaines juridictions nautorisent pas de limitations sur les garanties ou les recours pour violation dans certaines transactions. Dans de telles juridictions, les limites indiques dans ce paragraphe et dans le paragraphe prcdent pourraient ne pas sappliquer. Arbitrage, lois applicables : Tout litige dcoulant de cette entente sera rgl par arbitrage, devant un seul arbitre, Los Angeles, Californie, .-U., conformment aux rgles darbitrage commerciales de lAmerican Arbitration Association, et la dcision rendue lors de larbitrage pourra faire lobjet dun jugement par tout tribunal comptent. La prsente entente sinterprte conformment aux lois de ltat de la Californie, lexception de cette clause darbitrage, qui sera interprte conformment au Federal Arbitration Act. Au Canada, les garanties englobent les garanties et les conditions. Pour trouver le revendeur Epson autoris le plus prs de chez vous, visitez notre site Web ladresse www.epson.ca. Pour obtenir les coordonnes du centre de service aprs-vente Epson le plus prs de votre domicile, visitez notre site Web ladresse www.epson.ca/support. Pour communiquer avec Epson ConnectionMS, veuillez composer le 1 800 637-7661, le (905) 709-3839

(Canada) ou le (562) 276-4394 (.-U.). Vous pouvez nous crire ladresse postale Epson America, Inc., P.O. Box 93012, Long Beach, CA 90809-3012.