Regulatory Compliance Information Product Name:
WLAN / BT Module Model:
STI6290-D101 FCC Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. List of applicable FCC rules This module has been tested and found to comply with part 15.247, Part 15.407 requirements for Modular Approval. The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Antenna 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, 2) The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid, and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, maximum antenna gain (including cable loss) must not exceed. Antenna Type Frequency Band Ant 1 Gain
(MHz)
(dBi) Ant 2 Gain
(dBi) Wi-Fi Antenna 2400 ~ 2483.5 PIFA 5150 ~ 5250 5725 ~ 5850 Bluetooth Antenna PIFA 2400 ~ 2483.5 2.34 3.58 5.29
2.74 3.39 4.50 2.74 Important Note Notice that any deviation(s) from the defined parameters of the antenna trace, as described by the instructions, require that the host product manufacturer must notify to EPSON that they wish to change the antenna trace design. In this case, a Class II permissive change application is required to be filed by the USI, or the host manufacturer can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application Label of the end product:
The host product must be labeled in a visible area with the following:
" Contains FCC ID: BKMAE-STI6290 ". The end product shall bear the following 15.19 statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This module is restricted to integration into hosts for indoor use only. OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, , versus with multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04 The user manual of the end product should include:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device is restricted to indoor use. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. ISED This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. The device shall automatically discontinue transmission in cases of absence of information to transmit, or operational failure. This device is restricted to indoor use. The transmitter module may not be co-located with any other transmitter or antenna. Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization. Label of the end product:
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following:
Contains transmitter module IC: 1052D-STI6290. Contient le module d'mission IC: 1052D-STI6290 The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. CAN ICES-003(B) / NMB-003(B) The Country Code Selection feature is disabled for products marketed in the US/Canada For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. CE 1. RF power Compliance with 2014/53/EU Radio Equipment Directive (RED) In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table provides information on the frequency bands used and the maximum RF transmit power of the product for sale in the EU:
Frequency range (MHz) Max. Transmit Power (dBm/mW) 2400-2483.5 5150-5250 Bluetooth: 2402-2480 19.57 dBm (90.6mW) 19.66 dBm (92.5mW) 9.43 dBm (8.77mW) 2. RF Exposure Information (MPE) This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 3. The device for operation in the band 51505250 MHz is only for indoor use. AT EE IS NO BE EL IT PL BG ES LI PT CH FI LT RO CY FR LU SE CZ HR LV SI DE HU MT SK DK IE NL 4. Information of Importer:
EU Importer:
NameEPSON EUROPE B.V. AddressAtlas Arena, Asia Building, Hoogoorddreef 5,1101 BA Amsterdam Zuidoost The Netherlands TEL31-20-314-5000 FAX31-20-314-5010 Webhttp://www.epson.eu/
5. Information of Manufacturer:
Manufacturer:
NameSEIKO EPSON CORPORATION Address3-3-5, Owa, Suwa-shi, Nagano-ken 392-8502 Japan TEL81-263-87-5824 (ex.733-80485) 6. Declaration of Conformity UKCA 1. RF power Compliance with the Radio Equipment Regulations 2017 In accordance with 13 (2) (a) and 13 (2) (b) of the Radio Equipment Regulations 2017, the following table provides information on the frequency bands used and the maximum RF transmit power of the product for sale in the UK:
Frequency range (MHz) Max. Transmit Power (dBm/mW) 2400-2483.5 5150-5250 Bluetooth: 2402-2480 19.57 dBm (90.6mW) 19.66 dBm (92.5mW) 9.43 dBm (8.77mW) 2. RF Exposure Information (MPE) This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 3. The device for operation in the band 51505250 MHz is only for indoor use. UK (NI) 4. Information of Importer:
UK Importer:
NameEpson (UK) Ltd. AddressWestside, London Road, Hemel Hempstead, Hertfordshire, HP3 9TD, United Kingdom TEL44-1442-261144 FAX44-1442-227227 Webhttp://www.epson.co.uk 5. Information of Manufacturer:
Manufacturer:
NameSEIKO EPSON CORPORATION Address3-3-5, Owa, Suwa-shi, Nagano-ken 392-8502 Japan TEL81-263-87-5824 (ex.733-80485) 6. Declaration of Conformity