1 ON SPSPRDR1-8 UHF SPS Reader 1 Linx ANT-916-MHW-RPS-S UHF Antenna SPSPRDR1-8: User Manual Introduction;
The SPSPRDR1-8 Predictive Maintenance Turnkey Solution kit enables fast installation of full Smart Passive Sensor TM systems. This evaluation kit includes:
A 12V DC power supply is suggested and recommended for use with the SPSPRDR1-8. Software Tools ON Semiconductor has developed an application specifically for reading Smart Passive Sensors that unlocks the full functionality of the tags. This application utilizes a REST API that includes advanced reader settings, and graphing/logging of sensor data.. www.onsemi.com Figure 1. SPSPRDR1-8 Hardware Setup Semiconductor Components Industries, LLC, 2015 January 2019- Rev. P0 1 NON-CONTROLLED, PRE-PUBLICATION COPY PROPRIETARY, NOT FOR DISTRIBUTION TO CUSTOMERS Publication Order Number:
XXXXXEVBUM/D XXXXXEVBUM Hardware Setup The SPSPRDR1-8 requires three hardware connections to be made in the following order:
Connect at least one antenna to one of the RF ports on the SPSPRDR1-8 reader Connect an Ethernet cable from the SPSPRDR1-8 to the host computer that will be running the application software Plug in a power supply suitable for the SPSPRDR1-8 Note: please refer to SPS tag datasheets to verify optimal positioning to achieve best results. TagReader Software Setup If not already installed, install the Tag Reader application and Bojour Print Services (available from Apple Computer) onto the host computer. After the reader is powered on, open the TagReader application and wait for the reader to be automatically detected. The TagReader screen will then be shown as seen in figure 2. Check the box or boxes next to the antenna ports that you wish to use, set the region using the pull-down menu, and change any of the other settings as necessary. Click the Read button at the top of the screen to begin reading tags. The tag information read will be displayed on the Tags tab, as shown in figure 3. Figure 2. SPS Reader App startup screen Figure 3. SPS Reader App Tags tab NON-CONTROLLED, PRE-PUBLICATION COPY PROPRIETARY, NOT FOR DISTRIBUTION TO CUSTOMERS www.onsemi.com 2 XXXXXEVBUM The following antennas and cables are approved for use with this reader.
- MTI MT-242025/TRH/A
- Separate 6 ft 195 series cable, RPSMA<->RPTNC
(Citrus Cables SPXTPX240-06)
- ON SPSDEVA2-P (i.e. Galtronics)
- Separate 6 ft 195 series cable, RPSMA<->RPSMA
(Citrus Cables SPXSPX195-06)
- Linx ANT-916-MHW-RPS-S
- Built-in 79" RG-174 cable w/ RPSMA termination PRE-PUBLICATION COPY - NOT FOR DISTRIBUTION TO CUSTOMERS - PROPRIETARY XXXXXEVBUM Figure 5. Sensor information displayed under Tags and Graph tab IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment observe the following precautions:
1. READ these instructions. 2. KEEP these instructions. 3. PAY ATTENTION to all warnings. 4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance with the manufacturers instructions. 8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open flame sources on the product. 9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third-prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. ONLY USE attachments/accessories specified by the manufacturer. 12. UNPLUG this apparatus during lightning storms or when unused for long periods of time. 13. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus. 15. The MAINS plug or an appliance coupler shall remain readily operable. 16. The airborne noise of the Apparatus does not exceed 0dB (A). 17. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earth connection. PRE-PUBLICATION COPY - NOT FOR DISTRIBUTION TO CUSTOMERS - PROPRIETARY XXXXXEVBUM 18. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 19. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure. 20. Operate this product within its specified operating temperature range. 21. Protecting Against Electrostatic Discharge Static electricity can harm delicate components inside the system. To prevent static damage, discharge static electricity from your body before touching any of the electronic components, such as Antenna, USB and Ethernet connectors. This can be done by periodically touching an unpainted metal surface on the chassis. The following steps can also be taken prevent damage from electrostatic discharge (ESD):
21.1. When unpacking a static-sensitive component from its shipping carton, do not remove the component from the antistatic packing material until ready to install the component in the system. Just before unwrapping the antistatic packaging, be sure to discharge static electricity from your body. 21.2. When transporting a sensitive component, first place it in an antistatic container or packaging. 21.3. Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads, workbench pads and an antistatic grounding strap. 22. Equipment intended for installation in Restricted Access Location WARNING:
No user-serviceable parts inside. Refer all servicing to qualified service personnel. The safety certifications do not apply when the operating voltage is changed from the factory setting. SPSPRDR1-8 is with compliance to IEC/EN/UL/CSA 60950 "Safety of information technology equipment"
is one of the worlds most widely-used electrical product safety standards. Thousands of manufacturers rely on this standard to show that their products meet the safety requirements for markets around the world. It is one of the relatively few standards to be harmonized by standards-writing bodies globally to make the process as efficient as possible for manufacturers. Caution according to FCC Rule part 15.21 PRE-PUBLICATION COPY - NOT FOR DISTRIBUTION TO CUSTOMERS - PROPRIETARY XXXXXEVBUM Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Caution according to FCC Rule part 15.105 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. RF exposure Maintain a distance greater than 35 cm between the antenna of this device and persons during device operation, which is consistent with how the device is tested for compliance with RF exposure requirements and satisfies Federal Communications Commission (FCC) exposure requirements. Operations at closer than this distance are not recommended. Instructions de scurit importantes Pour rduire le risque de blessures corporelles, de chocslectriques, d'incendie et d'endommagement de l'appareil, observez les prcautions suivantes:
1. Lisez ces instructions. 2. Conservez ces instructions. 3. Faites ATTENTION tous les avertissements. 4. Suivez toutes les instructions. 5. N'utilisez pas cet appareil prs de l'eau. 6. Nettoyez uniquement avec un chiffon sec. 7. ne bloquez pas les ouvertures de ventilation. Prvoir des distances suffisantes pour une ventilationadquate et l'installer conformment aux instructions dufabricant. 8. Ne pas installer proximit de sources de chaleur tellesque flammes nues, radiateurs, registres de chaleur, polesou autres appareils (y compris les amplificateurs) quiproduisent de la chaleur. Ne placez aucune source de flamme nue sur le produit. 9. ne pas vaincre le but de scurit de la fiche de typepolarise ou mise la terre. Une fiche polarise a deux lames avec un plus large que L'autre. Une fiche de type mise la terre comporte deux lames etune troisime broche de mise la terre. La lame plus large ou la troisime broche est fournie pourvotre scurit. Si la fiche fournie ne rentre pas dans votre prise, consultezun lectricien pour le remplacement de la prise obsolte. 10. Protgez le cordon d'alimentation de la marche ou ducoincement, en particulier au niveau des fiches, des prisesde courant et du point de sortie de l'appareil. 11. N'utilisez que les accessoires et pices spcifis par lefabricant. 12. Dbrancher cet appareil pendant les orages ou Lorsqu'iln'est pas utilis pendant de longues priodes de temps. 13. Rfrez toutes les rparations au personnel de servicequalifi. L'entretien est ncessaire lorsque l'appareil a tendommag de quelque faon que ce soit, comme le cordond'alimentation ou la fiche est endommag, le liquide a trenvers ou des objets sont tombs dans l'appareil,l'appareil a t expos la pluie ou l'humidit, nefonctionne pas normalement, ou a t abandonn. 14. ne pas exposer l'appareil aux gouttes et aux claboussures. Ne pas mettre d'objets remplis de liquides, tels que desvases, sur l'appareil. 15. la fiche secteur ou un coupleur d'appareils doit demeurerfacilement utilisable. 16. le bruit arien de l'appareil ne dpasse pas 0 dB (A). 17. les appareils avec la construction de la classe I doiventtre connects une prise de courant avec un raccord deterre de protection. 18. pour rduire le risque d'incendie ou de choc lectrique,ne pas exposer cet appareil la pluie ou l'humidit. 19. N'essayez pas de modifier ce produit. Cela pourrait entraner des blessures corporelles et/ou unedfaillance du produit. 20. Actionnez ce produit dans sa plage de temprature defonctionnement spcifie. 21. protection contre les dcharges lectrostatiques L'lectricit statique peut endommager les composantsdlicats l'intrieur du systme. Pour viter des dommages statiques, dchargez l'lectricitstatique de votre corps avant de toucher L'un descomposants lectroniques, tels que l'antenne SMA, lesconnecteurs USB et Ethernet. Ceci peut tre fait en touchantpriodiquement une surface mtallique non peinte sur lechssis. PRE-PUBLICATION COPY - NOT FOR DISTRIBUTION TO CUSTOMERS - PROPRIETARY XXXXXEVBUM Les tapes suivantes peuvent galement tre prises pourviter d'endommager les dcharges lectrostatiques (ESD) 21,1. lors du dballage d'un composant sensible la statiquede son carton d'expdition, ne pas retirer le composant dumatriau d'emballage antistatique jusqu' ce qu'il soit prt installer le composant dans le systme. Juste avant de dballer l'emballage antistatique, assurez-vous de dcharger l'lectricit statique de votre corps. 21,2. lors du transport d'un composant sensible, placez-led'abord dans un contenant ou un emballage antistatique. 21,3. manipuler tous les composants sensibles dans unezone de scurit statique. Si possible, utilisez des patins antistatiques, des plaquettesde Workbench et une sangle de mise la terre antistatique. 22. quipement destin tre install dans un lieu d'Accsrestreint Avertissement:
Aucune pice de service l'utilisateur l'intrieur. Rfrez tous les services au personnel qualifi. Les certifications de scurit ne s'appliquent pas lorsque latension de service est change par le rglage d'usine. SPSPRDR1-8 Est conforme la norme IEC/EN/UL/CSA 60950scurit des quipements de technologie de l'informationest l'une des normes de scurit des produits lectriques lesplus largement utilises au monde. Des milliers de fabricants s'appuient sur cette norme pourdmontrer que leurs produits rpondent aux exigences descurit pour les marchs du monde entier. C'est l'une des normes relativement peu nombreuses harmoniser par les organismes d'laboration de normes l'chelle mondiale pour rendre le processus le plus efficacepossible pour les fabricants. Prudence selon la rgle FCC partie 15,21 Les modifications ou modifications non expressment approuves par la partie responsable de la conformit pourraient annuler l'autorisation de l'utilisateur de faire fonctionner l'quipement. Prudence selon la rgle FCC partie 15,105 Cet quipement a t test et jug conforme aux limites d'unappareil numrique de classe A, conformment la partie 15des rgles de la FCC. Ces limites sont conues pour assurer une protectionraisonnable contre les interfrences nuisibles lorsquel'quipement est utilis dans un environnement commercial. Cet quipement gnre, utilise et peut mettre de l'nergieradiofrquence et, S'il n'est pas install et utilisconformment au manuel d'instructions, peut causer desinterfrences nuisibles aux communications radio. Le fonctionnement de cet quipement dans une zonersidentielle est susceptible de causer des interfrencesnuisibles, auquel cas l'utilisateur sera tenu de corrigerl'interfrence ses propres frais. Exposition aux RF Maintenir une distance suprieure 35 cm entre l'antenne de cet appareil et les personnes pendant le fonctionnement de l'appareil, ce qui est conforme la faon dont le dispositif est test pour la conformit aux exigences d'exposition aux RF et rpond la Federal Communications Commission (FCC) conditions d'exposition. Les oprations au plus prs de cette distance ne sont pas recommandes. Label ON Semiconductor SEMICONDUCTOR COMPONENTS INDUSTRIES, LLC SPS UHF Reader / Hub; Lecteur / Centre Model; Modle : SPSDEVR1-8 Designed in Santa Clara, CA Assembled In China Conu dans Santa Clara, CA Assembl en Chine E499047 I.T.E. FCC ID: 2AQ8Q-SPSDEVR1-8 RoHS Attach the label on the back side of the Enclosure as recommended on this picture ON Semiconductor SEMICONDUCTOR COMPONENTS INDUSTRIES, LLC SPS UHF Reader / Hub; Lecteur / Centre Model; Modle : SPSDEVR1-8 Designed in Santa Clara, CA Assembled In China Conu dans Santa Clara, CA Assembl en Chine E499047 I.T.E. 89.00 20.00 0 0 1
. FCC ID: 2AQ8Q-SPSDEVR1-8 0 0
. 6 2 RoHS PRE-PUBLICATION COPY - NOT FOR DISTRIBUTION TO CUSTOMERS - PROPRIETARY XXXXXEVBUM Smart Passive Sensor is a trademark of RFMicron, Inc. Magnus is a registered trademark of RFMicron, Inc. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductors product/patent coverage may be accessed at www.onsemi.com/site/pdf/PatentMarking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. Typical parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customers technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 3036752175 or 8003443860 Toll Free USA/Canada Fax: 3036752176 or 8003443867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 8002829855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81358171050 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative PRE-PUBLICATION COPY - NOT FOR DISTRIBUTION TO CUSTOMERS - PROPRIETARY