A20 Manual Charging Power On/Off
(+) Button + Multi-function Button for 1 sec Volume Adjustment
(+) Button - Increase the volume
(-) Button - Decrease the volume Phone, Music Pairing Initially Pairing the A20 The Bluetooth system will automatically enter the phone pairing mode when you initially turn on the Bluetooth system or in the following situation:
Rebooting after executing Factory Reset 1. Press and hold the Multi-function Button and (+) Button for 1 second. 2. Search for Bluetooth devices on your mobile phone. Select the Parani A20 in the list of the devices detected on the mobile phone. 3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN. Music Operation Play or pause music: Press the Multi-function Button for 1 second. Track back: Press the (-) Button for 1 second. Track forward: Press the (+) Button for 1 second. Mobile Phone Call Making and Answering Answering a call: Tap the Multi-function Button Ending a call: Press the Multi-function Button for 2 seconds. Voice dial: Press the Multi-function Button for 3 seconds. Speed dial: Press the (+) Button for 3 seconds. Rejecting a call: Press the Multi-function Button for 2 seconds. Intercom Pairing 1. Press and hold the Multi-function Button of two Bluetooth systems for 5 seconds until red LEDs of both units start to flash rapidly. 2. Simply tap the Multi-function Button of any one of the two Bluetooth systems. Intercom Start/End 1st Friend: Tap the Multi-function Button once. 2nd Friend: Tap the Multi-function Button twice. 3rd Friend: Tap the Multi-function Button triple times Radio On/Off Turn on the FM radio: Press the (-) Button for 1 second. Turn off the FM radio: Press the (-) Button for 1 second. Radio Seek Stations Seek up stations: Double tap the (+) Button. Seek down stations: Double tap the (-) Button. Configuration Menu: Press the Multi-function Button for 15 seconds. Setting Troubleshooting Factory Reset If you want to restore the Bluetooth system to factory default settings, use the Factory Reset in the configuration menu. The Bluetooth system automatically restores the default settings and turns off. Certification and Safety Approvals FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antennae
-Increase the separation between the equipment and the receiver
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. FCC RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. When equipped, the distance between antenna and ones head surface is 38mm. FCC Caution Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void users authority to operate the equipment. Certification et homologation de scurit Dclaration de conformit FCC Cet appareil est en conformit avec la partie 15 des rgles de la FCC. Son fonctionnement est soumis aux deux conditions suivantes :
(1) Cet appareil ne doit pas crer dinterfrences prjudiciables et
(2) Cet appareil doit accepter toutes les interfrences reues, y compris celles qui pourraient entraver son bon fonctionnement. Cet quipement a t test et jug conforme aux limites pour un appareil numrique de classe B, conformment la partie 15 des rgles de la FCC. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nuisibles dans une installation rsidentielle. Cet quipement gnre et utilise de lnergie radio frquence et, sil nest pas install et utilis conformment. aux instructions, il peut occasionner des interfrences nuisibles au niveau des communications radios. Cependant, il nexiste aucune garantie que ces interfrences ne se produiront pas dans une installation particulire. Si cet quipement gnre des interfrences nuisibles la rception de la radio ou de la tlvision (ce quil est possible de dterminer en mettant lquipement hors tension, puis sous tension), lutilisateur est invit suivre une ou plusieurs des mesures suivantes pour corriger le problme des interfrences en prenant lune des mesures suivantes :
-Modifier lemplacement ou lorientation de lantenne de rception.
- loigner lappareil du rcepteur.
-Brancher lappareil sur une prise situe sur un circuit diffrent de celui du rcepteur.
-Consulter le revendeur ou un technicien expriment pour obtenir de laide. nonc FCC sur lexposition aux radiations RF Cet quipement est conforme aux rglementations FCC dexposition aux radiations dfinies pour un environnement non contrl. Les utilisateurs doivent respecter les instructions dexploitation spcifiques pour rpondre aux exigences de conformit sur lexposition aux RF. Lantenne utilise pour cet appareil ne doit pas fonctionner en mme temps quune autre antenne ou metteur, sauf sil y a conformit avec les procdures FCC des produits multi-metteurs. Cet appareil est conforme l'exigence d'exposition aux RF. Lorsque quip, la distance entre lantenne et la surface de la tte est de 38mm. LEST tant commercialis sans casque, il doit donc rester une distance de 30mm de la surface de la tte. Prcautions FCC Tout changement ou modification non expressment approuv par la partie charge de la mise en conformit peut annuler le droit de lutilisateur utiliser lquipement. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the Industry Canada(IC) Statement following two conditions:
(1)this device may not cause interference, and the device.
(2)this device must accept any interference, including interference that may cause undesired operation of Le present appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorisee aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. IC RF Exposure Statement Cet quipement est conforme aux limites d'exposition aux radiations de la FCC dfinies pour un environnement non contrl. Les utilisateurs finaux doivent suivre les instructions d'utilisation spcifiques pour satisfaire la conformit d'exposition RF. L'antenne utilise pour cet metteur ne doit pas mettre simultanment avec d'autres antennes ou metteurs, sauf en conformit avec les procdures FCC relatives aux produits multi-metteurs. Lorsque quip, la distance entre lantenne et la surface de la tte est de 38mm.