Sengled Zigbee Module Model: ZM001 Introduction Model ZM001 is a zigbee module. The wireless communication part of the product is based on ZigBee Compliant Platform ,CustomNodes EFR32MG13P732F512IM32-C technology, which are fully integrated System-on-Chips that integrate a 2.4 GHz, IEEE 802.15.4-2003-compliant transceiver, 32-bit ARM Cortex-M4 microprocessor, flash and RAM memory, and peripherals of use to designers of ZigBee-based systems. Sengled Zigbee Module 0x00000018 0x01 Product Name:
Hardware Version:
Software Version:
Device Operating Configurations:
Operating Mode(s):
Supporting Mode(s):
Test Modulation:
IEEE 802.15.4 O-QPSK 2.4 GHz IEEE 802.15.4 Frequency Range:
Mode 2.4 GHz IEEE 802.15.4 Tx (MHz) Rx (MHz) 2400 ~ 2483.5 2400 ~ 2483.5 B.HF crystal OSC A high frequency crystal oscillator (HFXO) with integrated load capacitors, tunable in small steps, provides a precise timing refer-
ence for the MCU. Crystal frequencies in the range from 38 to 40 MHz are supported. An external clock source such as a TCXO can also be applied to the HFXO input for improved accuracy over temperature. C.Power supply circuit The AC 100-130V power is converted to DC 3.3V and feeds to the whole zigbee module. The 2.1-3.6 V with internal 1.8 V regulators DC is used by the EFR32MG13 as the input power . D.Antenna The EFR32MG13 family includes devices which support both single-band and dual-band RF communication over separate physical RF interfaces. The 2.4 GHz antenna interface consists of two pins
(2G4RF_IOP and 2G4RF_ION) that interface directly to the on-chip BALUN. The 2G4RF_ION pin should be grounded externally. The sub-GHz antenna interface consists of a dierential transmit interface (pins SUBGRF_OP and SUBGRF_ON) and a dierential re-
ceive interface (pinsSUBGRF_IP and SUBGRF_IN). The external components and power supply connections for the antenna interface typical applications are shown in the RF Matching Networks section. FCC/ISED Regulatory notices:
Modification statement Sengled Co., Ltd. has not approved any changes or modifications to this device by the user. Any changes or modifications could void the users authority to operate the equipment. Sengled Co., Ltd. napprouve aucune modification apporte lappareil par lutilisateur, quelle quen soit la nature. Tout changement ou modification peuvent annuler le droit dutilisation de lappareil par lutilisateur. Interference statement This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. RF exposure This equipment complies with FCC and ISED radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. Antenna gain must be below:
Antenna Gain Frequency Band ZigBee FCC ID: 2AGN8-ZM001 Model: ZM001 1.5dBi This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The host end product must include a user manual that clearly defines operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines. For portable devices, in addition to above, a separate approval is required to satisfy the SAR requirements of FCC Part 2.1093. If the device is used for other equipment that separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and dierent antenna configura-
tions. Cet appareil est conforme aux limites d'exposition aux rayonnements de lISED pour un environnement non contrl. L'antenne doit tre install de faon garder une distance minimale de 20 centimtres entre la source de rayonnements et votre corps. Gain de l'antenne doit tre ci-dessous:
Gain de lantenne ZigBee:1.5dBi L'metteur ne doit pas tre colocalis ni fonctionner conjointement avec autre antenne ou autre metteur. FCC Class B digital device notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Labelling Requirements for the Host device The host device shall be properly labelled to identify the modules within the host device. The certification label of the module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the FCC ID and ISED of the module, preceded by the words
"Contains transmitter module", or the word
"Contains", or similar wording expressing the same meaning, as follows:
Model: E1D-G73 Contains FCC ID: 2AGN8-ZM001 Contains IC: 20888-ZM001 The host OEM user manual must also contain clear instructions on how end users can find and/or access the module and the FCC ID and ISED. L'appareil hte doit tre tiquet comme il faut pour permettre l'identification des modules qui s'y trouvent. L'tiquette de certification du module donn doit tre pose sur l'appareil hte un endroit bien en vue en tout temps. En l'absence d'tiquette, l'appareil hte doit porter une tiquette donnant le FCC ID et lISED du module, prcd des mots Contient un module d'mission , du mot Contient ou d'une formulation similaire exprimant le mme sens, comme suit :
CAN ICES-3 (B) / NMB-3 (B) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de classe B est conforme la norme canadienne ICES-003. Installation Guidance The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form. To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. For example, if a host was previously authorized as an unintentional radiator under the Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements.