Transmitter Certification Test Report FCC ID: SDBTGB001LP/SDBTGB001HP FCC Rule Part: CFR 47 Part 24 Subpart D, Part 90 Subpart I, Part 101 Subpart C ACS Report Number: 05-0169-LP/05-0169-HP Manufacturer: Advanced Metering Data Systems, LLC Equipment Type: Base Station Transceiver Model(s): TGB001LP TGB001HP Users Manual 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 TGB 900MHz Users Manual & Operators Guide Prepared by:
AMDS 2021 Lakeshore Dr. Suite 414 New Orleans, LA 70122 PH: (504)304-2502 To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 1 consent is prohibited. AMDS CONFIDENTIAL 1. DESCRIPTION 1.1. Purpose The purpose of this document is to provide necessary information for use by field personnel in the installation, operation, and troubleshooting of the 900MHz Cell Tower Gateway Basestation (TGB). To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 2 consent is prohibited. AMDS CONFIDENTIAL 1.2. FCC Class B Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this device not expressly approved by AMDS could void the users authority to operate the equipment. RF Exposure In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element shall be installed such that a minimum separation distance of:
For HP Models (i.e. FCC ID and IC IDs end in HP) a distance of 2.5 meters. For LP Models (i.e. FCC ID and IC IDs end in LP) a distance of 0.5 meters. Note: These limits are for CFR 47 Part 90 and Par101 operation. CFR 47 Part 24 limits will be addressed at time of licensing according to Part 1.1307 of CFR 47. This information presented is correct for all three Rule Parts. To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 3 consent is prohibited. AMDS CONFIDENTIAL 1.3. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numrique de la classe B rpond toutes les exigences de l'interfrence canadienne causant des rglements d'quipement. L'opration est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'interfrence nocive, et (2) ce dispositif doit accepter n'importe quelle interfrence reue, y compris l'interfrence qui peut causer l'opration peu dsire. 1.4. Specifications 1.4.1. Input Power Input Current 1.4.1.1. Voltage: 24VDC 1.4.1.2. 10A max (at low input voltage range) Approximately 3A continuous 1.4.1.3. Alarms and Controls Low-voltage alarm is asserted when output voltage drops below 22VDC. Low-voltage disconnect is asserted when output voltage drops below 20VDC, re-connects when output voltage exceeds 22VDC. 1.4.2. Environmental 1.4.2.1. Operating temperature
-40C to +85C 1.4.2.2. Storage temperature
-40C to +85C 1.4.2.3. Humidity 0% to 95%, non-condensing To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 4 consent is prohibited. AMDS CONFIDENTIAL 1.4.3 General Information The TGB Transceiver is a high performance burst data radio system. The RF receiver is configured to receive 3 distinct modulation schemes on 3 adjacent frequencies in the 896 to 940 MHz frequency range. The TGB RF Transmitter operates on a single configurable channel (12.5kHz, 13.6 KHz, or 25kHz authorized bandwidth depending on the channel and FCC Rule section governing its operation) in the 935 to 960 MHz frequency range. The transmitter utilizes yet another type of modulation scheme, different from the three utilized by the receiver. Transmitted and received data messages are short in nature, meaning that the radio is intended for burst telemetry type of applications. Larger packets may, however, be transmitted by sending successive packets. The TGB operates as a multi-channel transceiver in a cellular type system. The TGB assembles the received messages and forwards them to the TGB Controller (one per city) via local phone lines. The TGB Controller eliminates redundant messages (i.e., messages from endpoints that were received by more than one TGB) before forwarding them to the NOC via a high-speed connection (ISDN, T1, etc). The TGB shall also notify the NOC of any alarm indications, such as tamper/intrusion, temperature alarms, or power failure. The TGB is installed inside an equipment enclosure containing a 24 VDC power supply and battery charger (FCC Part 15 Class B Compliant), a cavity duplexer/combiner allowing for single antenna operation, and all necessary grounding and lightning protection hardware needed to protect the TGB under normal operation. To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 5 consent is prohibited. AMDS CONFIDENTIAL 1.5. Block Diagram 1.5.1. Power System
!!! Danger !!!
Hazardous AC voltages capable of producing severe electrical shock are present at various locations in the TGB. Exercise caution when working inside the enclosure, to assure that contact is not made with and electrical termination.
!!! Warning !!!
The batteries are a source of energy and can be hazardous if shorted. Exercise caution. 1.5.1.1. AC Power Indoor AC Power is supplied to the rectifier through a rack mounted power strip with integral ON/OFF switch and surge protection. 1.5.1.2. AC Power Outdoor AC Power enters the outdoor enclosure through the bottom of the cabinet. The rectifier plugs into the surge protected, GFI outlet located in the bottom of the cabinet. 1.5.1.3. DC Power An FCC, Part 15, Class B compliant rectifier (battery charger) converts commercial power (120/220VAC) to 24VDC power to the equipment chassis, heat exchanger, fans, intrusion alarm, and batteries. In the event of commercial power failure, the rectifier provides uninterrupted DC power by switching over to battery backup. 1.5.1.4. Fuses and Breakers The TGB contains one 10A circuit breaker/disconnect to protect/control power to the electronics chassis. 1.5.1.5. Grounding The ground bus bar MUST be connected to the sites HALO ground using an insulated conductor of sufficient size. All transient voltage protectors (antenna, commercial power, TELCO lines) are grounded to this bus bar. Failure to properly ground the TGB equipment presents a risk to not only the TGB electronics, but other customers equipment at the site as well. A qualified electrician must perform this connection. Consult a local electrician, or site engineer, for size requirements. To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 6 consent is prohibited. AMDS CONFIDENTIAL 1.5.2. Wiring The TGB equipment enclosure wiring is supplied in another document and is beyond the scope of this manual. All TGB connections to the wiring and interconnect of the TGB equipment enclosure are provided below to assist the operator in installing the TGB inside the equipment enclosure. 1.5.3. Alarms Intrusion 1.5.3.1. The enclosure the TGB is mounted in is equipped with pin switches on both the front and rear doors that activate and intrusion alarm when a door is opened. A feature of the outdoor enclosures intrusion switch is the ability to pull out the switch to cancel the alarm. The switch has a 30-minute mechanical delay, after which the intrusion alarm will again be asserted. 1.5.3.2. Temperature The TGB is equipped with high (120F) and low (41F) temperature sensors. The TGB notifies the TGB controller of the type of alarm. 1.5.3.3. Power System The rectifier has several alarm outputs to signal different types of faults associated with the power system. Low Voltage Alarm Asserted upon loss of AC Commercial Power. Rectifier Failure Asserted when DC output voltage is out-of-range. Load Fuse Failure Asserted when one of the load fuses (Fan, Heat Exchanger, Intrusion Alarm) opens. Battery Failure Asserted when output voltage drops below threshold, Low voltage disconnect is activated, or Bypass switch is in Bypass position. 1.5.4. RF Subsystem 1.5.4.1. Spark Gap The antenna bulkhead connector is a Gas Discharge Tube Surge Arrestor designed to shunt lightening induced transients to ground;
thereby protecting the TGB electronics from damage. The arrestor contains a replaceable gas tube element that should be inspected regularly are replaced as necessary. 1.5.4.2. Cavity Filter / Duplexer The cavity filter is a frequency selective device designed to protect the RF front end from overloading by out-of-band signals. The cavity filter assembly is tuned and assembled as a unit by qualified AMDS personnel. No cables or connectors should be changed or replaced, To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 7 consent is prohibited. AMDS CONFIDENTIAL nor should any adjustments be made to the tuning screws of the Cavity Filter / Duplexer by the operator. 1.5.4.3. RF Cabling The RF cabling and connectors inside the TGB enclosure are selected due to their low-loss characteristics. No cables or connectors should be changed or replaced by the operator. 1.5.5. Breakout Panel Assembly The purpose of the Breakout Panel is to function as an interface between the Fusion Processor and the external world. It provides a termination point, and more importantly Transient Voltage Suppression, of signals coming into the Fusion Processor. TVS devices protect all Alarm Inputs, Modem Lines, and Ethernet Lines. Signal POTS1 POTS2 Diagnostic Port Inputs 1-7 Ethernet 2. Installation I/O Bi-directional Function/Comments POTS Modem Connections Bi-directional Inputs Bi-directional DB9 Female connector wired as a DCE Contact Closure Alarm Inputs. 10/100Base T Ethernet Port 2.1. Ventilation The outdoor enclosure is completely sealed from the outside environment
(NEMA 4). A heat exchanger is used to cool internal electronics. The indoor enclosure is designed to circulate ambient air for cooling. Fans inside the enclosure are designed to circulate air across the electronics and power supply. 2.2. Electrical Connections 2.2.1. Grounding Ensure that all connections to the Ground bus bar are secure. The bus bar must also be connected to the sites Halo Ground using the 8AWG Green/Yellow cable provided with the TGB System. To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 8 consent is prohibited. AMDS CONFIDENTIAL 2.2.2. Power/Battery
!!! Warning !!!
Do not make any connections with power applied to the system. The batteries are a source of energy and can be hazardous if shorted. Exercise caution. Prior to connecting batteries, disconnect the battery cable from the right hand side of the rectifier cabinet. Install batteries and connect jumpers to battery terminals. Before reconnecting battery cable to right hand side of rectifier cabinet, measure open circuit voltage between pins 1 & 2. The voltage should be above 24VDC. If the voltage is below 22VDC, do not proceed with connectionbatteries must first be charged before installation. 2.2.3. Antenna The antenna connection is a Type-N female located on the top of the indoor cabinet (bottom of the outdoor cabinet). The connector is a bulkhead mounted surge arrestor rated at 90V. The antennas (and their installations, including separation distances) utilized by the TGB must follow the following FCC guidelines:
For Part 24:
The antenna(s) used for this transmitter (receiver) must be fixed-mounted on outdoor permanent structures. RF exposure compliance is addressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of 1.1307(b)(3). For Part 90 and Part 101 Operation:
The antenna(s) used for this transmitter must be fixed-mounted on outdoor permanent structures with a separation distance of 2.5 meters for the HP model and 0.5 meters for the LP model (Note: Model numbers are ascertained by either front panel labeling or by noting the IC or FCC ID label placed on the rear panel of the TGB) from all persons during normal operation. The peak conducted output power at each antenna terminal must not exceed 1.24 Watts for the LP model and 32.21 Watts for the HP Model. The peak radiated output power (EIRP) must not exceed 16.14 Watts for the LP model and 418.8 Watts for the HP model. To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 9 consent is prohibited. AMDS CONFIDENTIAL Antenna Co-Location At Multiple-Transmitter Sites:
According to 1.1307(b)(3), the FCC requires the following (excerpted from CFR 47):
(3) In general, when the guidelines specified in 1.1310 are exceeded in an accessible area due to the emissions from multiple fixed transmitters, actions necessary to bring the area into compliance are the shared responsibility of all licensees whose transmitters produce, at the area in question, power density levels that exceed 5% of the power density exposure limit applicable to their particular transmitter or field strength levels that, when squared, exceed 5% of the square of the electric or magnetic field strength limit applicable to their particular transmitter. Owners of transmitter sites are expected to allow applicants and licensees to take reasonable steps to comply with the requirements contained in 1.1307(b) and, where feasible, should encourage co-location of transmitters and common solutions for controlling access to areas where the RF exposure limits contained in 1.1310 might be exceeded. 2.3. Data Link The TGB supports several different communications backbonesa single/dual modem (56K) connection or a 10/100BaseT Ethernet connection. The modems and Ethernet connections are made through the modular connectors on the breakout panel. 2.4. Initial Startup Prior to applying power, ensure that all fuses are in place, the antenna is connected, the 24 VDC supply is connected to the TGB, and the data line
(POTS or Ethernet) is connected. After approximately 30 seconds, the Fusion Processor will complete its boot up procedure, and the TGB will connect to the TGB Controller. After approximately 1 minute, the TGB boot-up sequence should be completed. All LEDs indicating a green color on the front panel informs the operator that the TGB is operating correctly and has passed all self tests. To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 10 consent is prohibited. AMDS CONFIDENTIAL IF ANY RED LIGHTS ARE DISPLAYED ON THE TGB FRONT PANEL, POWER DOWN THE UNIT AND CALL THE OPERATIONS CENTER FOR FURTHER INSTRUCTIONS. 3. Operation 3.1. General The TGB is designed to operate with minimal user interventioneven in the event of commercial AC power interruption. Specialized software may be used (available ONLY to authorized AMDS technical personnel pursuant to the requirements of CFR 47 Part 90.203) to configure the control parameters of the TGB at the installation site for setup and troubleshooting. For all installation purposes other than those expressly listed above, performed by authorized AMDS personnel, you, the operator, only have the ability, and are authorized to:
Connect power to the unit. Attach the interconnect cabling to the unit (i.e. RF cables, POTS interconnect). status. Turn on and off the units power. Connect a diagnostic cable to the unit to allow for monitoring of system Run a monitoring and control program on an IBM PC compatible computer that allows you to monitor several TGB status indicators and to power up and down the unit. Visually ascertain certain system operational parameters by viewing the LED indicators on the front panel of the TGB. Work with AMDS authorized personnel to ascertain if the TGB is operating properly. Pursuant to FCC regulations, you the operator are NOT allowed to perform the following tasks by any means. Operators that do not adhere to these important guidelines will face disciplinary action and may be prosecuted under the laws of the United States Of America or Canada:
You may not program new transmitter or receiver frequencies (these are programmed by authorized AMDS personnel either at the site or at the AMDS service depot using specialized software or via an internet connection using a secure data link). You may not program any on-air related characteristics of the TGB. NOTE: The items listed immediately above may not be invoked in any way due to any control on the front panel of the TGB pursuant to CFR 47 Part 90.203 of To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 11 consent is prohibited. AMDS CONFIDENTIAL the FCC Rules. Highly controlled and specialized software, protected using password login is utilized (either through a specialized diagnostic port or via a secure internet link to the TGB) by ONLY AMDS authorized personnel, to program any of the on-air operational parameters of the TGB. 3.2. Starting and Stopping Prior to powering down the TGB Electronics, the Halt command should be issued to the Fusion Processor via the internet link or by qualified AMDS service personnel. After the Fusion Processor has completed shutdown, the TGB Electronics can then be powered-down by switching the Chassis breaker/disconnect to the OFF position. To start the TGB Electronics simply switch the Chassis breaker/disconnect to the ON position. If a qualified AMDS service professional is not present to execute the Halt command to the Fusion Processor, the unit may be powered off (and then on if desired) by the operator with no detriment to the system or its operation. If this scenario is performed by the operator it is the operators responsibility to inform the AMDS network operations center of this condition so that AMDS personnel can perform the appropriate housekeeping for the TGB via the secure internet link. To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 12 consent is prohibited. AMDS CONFIDENTIAL 3.3. Indicators Indicator INPUT OK Location Power Supply FAULT POWER Power Supply Fusion Processor IN1 thru IN7 Fusion Processor TRIP MSG OK RESET POWER OTR POWER LOCK AC POWER OK RECTIFIER FAILURE LOAD FUSE FAILURE BATTERY FAILURE CPC CPC CPC A/D A/D A/D Receiver Receiver Rectifier Rectifier Rectifier Rectifier Description GRN Input voltage within normal operating limits RED Output Voltage Fault GRN Fusion Processor Power OK OFF Fusion Processor Power Fail RED Alarm Input Active OFF Alarm Input not Active Flash RED Trip Detected Flash AMBER Valid Message Received GRN CPC Power OK OFF CPC Power Fail RED System RESET Asserted OFF System OK GRN A/D Power OK OFF A/D Power Fail Flash AMBER Input Over-range GRN Receiver Power OK OFF Receiver Power Fail AMBER Synthesizer Locked RED Synthesizer Unlocked GRN AC Power OK OFF AC Power Fail RED DC Output Voltage Out of Range OFF Normal Operation RED Load Fuse Failed OFF Normal Operation RED Output Voltage Low, or Low Voltage Disconnect Activated, or Switch in BYPASS OFF Normal Operation Shaded areas indicate Normal Operation. 3.4. Low Voltage Alarm and Disconnect Upon Commercial AC Power Failure, the TGB will immediately notify the network via the AC POWER Alarm; at which time the system will begin operating on battery backup. After duration determined by capacity of batteries, charge state, temperature, and current draw, the output voltage of the batteries will decrease. To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 13 consent is prohibited. AMDS CONFIDENTIAL The system provides for local visual (BATTERY FAILURE) and remote indication the system output voltage has fallen below a preset level. This level is set at the factory at 24V. The alarm clears automatically when the system output voltage increases above this level. The Low Voltage Alarm is the final indication that the TGB system is about to shut down. Once asserted the TGB will shutdown in approximately 8 hours unless commercial AC power is restored.. 4. Maintenance 4.1. General The TGB is designed to require minimal maintenance. Care should be taken to observe the appropriate precautions when working inside the TGB enclosure. The circuit cards used in this equipment contain static sensitive
devices. Observe precautions for handling ESD sensitive items. A, ESD wrist strap is located inside the front door of the TGB enclosure. 4.2. Preventative or Routine Maintenance 4.2.1. Surge arrestor The antenna surge arrestor is of the gas discharge tube type. A gas tube element may not always show outward signs of failure or degradation, therefore routine maintenance and inspection is recommended. The gas tube element can be replaced by simply removing the nut and replacing the element. If the number of thunderstorms in an area is high, gas tubes should be inspected more frequently. Gas tube degradation is dependant on the number of strikes as well as the intensity of the strikes. As obvious as it may seem, gas tube elements should never be inspected, or replaced, when a thunderstorm is approaching or occurring. 4.2.2. Airflow Without adequate airflow, TGB performance may degrade due to increased temperature. At least once per year, the TGB enclosures should be checked for proper airflow. This includes verifying operation of all fans and ensuring that any air filters are free of dust and dirt. 4.3. Circuit Card Installation/Replacement No operator or user serviceable equipment is provided in the TGB with the exception of battery replacement and other housekeeping items. IF ANY HARDWARE OR SOFTWARE FAILURE IS REPORTED OR DETECTED SERVICING IS TO BE PERFORMED BY QUALIFIED AMDS TECHNICAL SERVICE PERSONNEL ONLY!!
To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 14 consent is prohibited. AMDS CONFIDENTIAL 4.4. Battery Replacement
!!! Warning !!!
The batteries are a source of energy and can be hazardous if shorted. Exercise caution. The batteries are rated for a 5-yr life at 25C and 27.5VDC float voltage. Extended periods of operation above 25C will reduce battery life (rule of thumb: 50% life reduction per every 10C increase. After this time it is appropriate to have a change-out program. In the event of frequent deep discharges it is possible that the batteries may require earlier replacement. Prior to disconnecting batteries, disconnect the battery cable from the right hand side of the rectifier cabinet. Remove jumpers from the battery terminals and remove old batteries. Install new batteries and reconnect jumpers. Before reconnecting battery cable to right hand side of rectifier cabinet, measure open circuit voltage between pins 1 & 2. The voltage should be above 22VDC. If the voltage is below 22VDC, do not proceed with connectionbatteries must first be charged before installation. 4.5. Battery Recharging The batteries are a source of energy and can be hazardous if shorted.
!!! Warning !!!
Exercise caution. The shelf life of the batteries is 6 months from the date of charge. If the battery has been stored for more than 6 months, it should be recharged prior to installation. To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 15 consent is prohibited. AMDS CONFIDENTIAL 5. Ordering Information and Parts List Manufacturer 5.1. Spares Kit Description Antenna Surge Arrestor Andrews Andrews Gas Tube Generator Plug Hubbell 1 1/3A GMT Fuse Bussmann Littlefuse Bussmann Littlefuse Bussmann Littlefuse 5A GMT Fuse 2A GMT Fuse Part Number APG-BNFNF-090 GASTUBE-090 2713 GMT - 1 1/3 A HB481001.33 GMT - 2 A HB481002 GMT - 5 A H481005 To be used only for the purpose for which it is submitted. All rights reserved to AMDS LLC. Reproduction without written 16 consent is prohibited. AMDS CONFIDENTIAL