Certification Exhibit FCC ID: SDBFLXA3D IC: 2220A-FLXA3D FCC Rule Part: CFR 47 Part 24 Subpart D, Part 101, Subpart C ISED Canadas Radio Standards Specification: RSS-119, RSS-134 TV SD Project Number: 72133516 Manufacturer: Sensus Metering Systems, Inc. Model: FLXA3D Manual 2320 Presidential Drive, Suite 101, Durham, NC 27703 USA Voice: 919-381-4235 FlexNet SmartPoint Module for Honeywell A3 ALPHA Quick Guide The Sensus FlexNet SmartPoint module provides wire-
less communication capability to electric utility meters. The Honeywell A3 ALPHA meter is a very accurate revenue meter that provides advanced four-quadrant revenue func-
tions, transformer and line loss compensation, and increased data profiling. Insert photo of A3 ALPHA with Sensus label here. SPECIFICATIONS The A3 ALPHA meter with the FlexNet module will have a visible label containing the follow-
ing information:
Technical Overview
Contains Model: FLXA3D
Contains FCC ID: SDBFLXA3D
Contains IC: 2220A-FLXA3D The FlexNet communications network offers a simple, reliable, and secure system that is economical for mass meter deployments, strategic deploy-
ments, and rural applications while providing a multi-application solution for all AMI end points. The FlexNet network enhances the A3 ALPHA meter by providing AMI capability. The FlexNet SmartPoint module is a printed circuit board which provides wireless communication capability to the Honeywell A3 ALPHA electric meter. The SmartPoint module interrogates the meter registers on a pro-
grammable interval from five minutes to daily readings. The SmartPoint module then transmits the meter consumption and status information at regular intervals. The module mounts into the existing A3 ALPHA meter and acts as a third party AMR board. It is designed to mount mechanically into the meter with no additional mechanical modification required. The module communicates via the FlexNet fixed wireless telemetry network to provide electric meter readings and diagnostic data from the meter to the utility provider via radio. The module contains both a receiver and transmitter to allow for two-way communications over the FlexNet network. QUICK GUIDEEQG-10006-04 FlexNet SmartPoint Module for Honeywell A3 ALPHA Warnings & Hazards WARNING Sensus devices are for professional installation only. They are to be serviced by professional personnel only. This product is NOT for consumer installation or servicing. WARNING The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter. AT TENTION Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communi-
cations. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different form that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help WARNING If you are not sure of the rated power of your radio, contact your Sensus representative or dealer and supply the product model number found on the product label. If you cannot determine the rated power out, then assure 3-feet separation from the body to the device. WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT RE-
MOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. R ADIATION HA Z ARD In order to satisfy the FCC RF exposure limit for transmitting devices, a separation distance of 20cm (7.87 inches) or more should be maintained while operating the Sensus FLXA3D. To ensure compliance, operation at closer than this distance is not recommended. This minimum safe distance is required between personnel and the antenna of this device. R ADIATION HA Z ARD In order to satisfy the ISED RF exposure limit for transmitting devices, a separation distance of 26cm (10.2 inches) or more should be maintained while operating the Sensus FLXA3D. To ensure compliance, operation at closer than this distance is not recommended. This minimum safe distance is required between personnel and the antenna of this device. Afin de satisfaire la limite dexposition RF pour les appareils de transmission, une distance de sparation de 26cm (10.2 pouces) ou plus doit tre maintenu pendant le fonctionnement du Sensus FLXA3D. Pour assurer la conformit, un fonctionnement distance infrieure celle est pas recommande. Cette distance minimale de scurit est ncessaire entre le personnel et lantenne de cet appareil. AT TENTION Any modifications made to this device that are not approved by Sensus may void the authority granted to the user by the FCC to operate equipment. AT TENTION This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit ac-
cepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. AT TENTION This radio transmitter the Sensus FLXA3D has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (Sensus FLXA3D) a t approuv par Industrie Canada pour fonctionner avec les types dantenne numrs ci-dessous et ayant un gain admissible maximal et limpdance requise pour chaque type dantenne. Les types dantenne non inclus dans cette liste, ou dont le gain est supri-
eur au gain maximal indiqu, sont strictement interdits pour lexploitation de lmetteur. dipole with peak gain of 1.8 dBi EQG-10006-04 FlexNet SmartPoint Module for Honeywell A3 ALPHA Warnings & Hazards AT TENTION Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radi-
ated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation dIndustrie Canada, le prsent metteur radio peut fonctionner avec une antenne dun type et dun gain maximal (ou infrieur) approuv pour lmetteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique lintention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas lintensit ncessaire ltablissement dune communication satisfaisante. AT TENTION ICES-003 Class B NoticeAvis NMB-003, Class B This Class B digital apparatus complies with Canadian ICES-003 Cet appareil numerique de la classe B est conforme la norme NMB-003 du Canada. 8601 Six Forks Rd, Ste 700 Raleigh, NC 27615 1-800-638-3748 sensus.com 2017 Sensus. All products purchased and services performed are subject to Sensus terms of sale, available at either sensus.com/TC or 1-800-638-3748. Sensus reserves the right to modify these terms and conditions in its own discretion without notice to the customer. The Sensus logo is a registered trademark of Sensus.This document is for informational purposes only, and SENSUS MAKES NO EXPRESS WARRANTIES IN THIS DOCUMENT. FURTHERMORE, THERE ARE NO IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, WARRANTIES AS TO FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. ANY USE OF THE PRODUCTS THAT IS NOT SPECIFICALLY PERMITTED HEREIN IS PROHIBITED.