5GHz AUDIO TRANSCEIVER PANDA / ATM210 DATASHEET REV 00 June 10, 2019 SEONG JI INDUSTRIAL CO., LTD 54-33, Dongtanhana 1gil, Hwaseong-si, Gyeonggi-do, South Korea PBA RF Module 5GHz Wireless Audio Transceiver ATM210 REV: 00 CONTENTS 1. Revision History .......................................................................................................................................................... 3 2. Scope ........................................................................................................................................................................ 4 3. Product Information .................................................................................................................................................... 4 3-1. Product Information ................................................................................................................................... 4 3-2. Part Number .............................................................................................................................................. 4 4. Introduction ................................................................................................................................................................ 5 5. Electrical Specifications ............................................................................................................................................... 7 5-1. Absolute Maximum Ratings ............................................................................................................................... 7 5-2. Recommended operating Range ........................................................................................................................ 7 5-3. Electrical Characteristics DC ............................................................................................................................ 7 5-4. Electrical Characteristics RF TX ........................................................................................................................ 8 5-5. Electrical Characteristics RF RX ........................................................................................................................ 9 5-6. Electrical Characteristics RF PLL ....................................................................................................................... 9 5-7. Electrical Characteristics Audio C/CS ............................................................................................................... 9 5-8. AV5100 Rate Converter Characteristics ............................................................................................................ 10 5-9. I2S Communication Interface Timing ................................................................................................................ 11 5-10. I2C Slave Communication Interface Timing...................................................................................................... 12 6. I/O Connector Pin Description ................................................................................................................................... 14 7. Mechanical Specifications .......................................................................................................................................... 15 7-1. Module dimension .......................................................................................................................................... 15 7-2. Antenna dimension ......................................................................................................................................... 15 8. Label Specification .................................................................................................................................................... 16 9. Certificate Statement ................................................................................................................................................ 17 2 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver 1. Revision History No. 1 Revision 00 Content Initial release ATM210 REV: 00 Date Revision Page 2019-06-10 3 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver 2. Scope This document is the specifications of 5GHz wireless audio transceiver module, ATM210. ATM210 REV: 00 3. Product Information 3-1. Product Information ITEMS Manufacturer Product type Product application Project Name Model Name Part Number Regulatory Certification FCC IC CE DESCRIPTION SEONG JI INDUSTRIAL CO,.LTD Wireless Audio Transceiver Mono/Stereo wireless audio system PANDA ATM210 WSATM210x00 2AS8LATM210 25119-ATM210 TBD 3-2. Part Number W
(1) S
(2) A
(3) T
(4) M
(5) 2
(6) 1
(7) 0
(8) x 0 0
(9)
(10)
(11) No.
(1),(2)
(3),(4)
(5)
(6)
(7)
(8)
(9)
(10),(11) EXPLANATION Wireless Solution Application (AT: Audio Transceiver) Type (M:Module) Group model : Main Chip (2:Avnera AV5100) Development Code (0: w/PA, 1: w/o PA) Development Code (0:default, 1: expansion) Customer Code Firmware application 00 : TX 10 : RX 4 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver 4. Introduction ATM210 REV: 00 The ATM210 is 5GHz AUDIO TRANSCEIVER that optimized for building point to multi-point digital wireless audio solutions such as wireless subwoofers and wireless rear speakers in home theater system. This wireless audio module provides a highly-integrated and flexible wireless audio solution based on the AV5100 SoC. The AV5100 SoC has the VMI RF protocol, providing a excellent coexistence performance and also provide the capabilities of world-class wireless audio protocol by supporting increased digital I/O and OTA (over-the air) signal routing flexibility to accommodate a wide range of wireless audio application. It features low fixed latency, multiple OTA audio configurations, uncompressed CD quality mono or stereo audio, excellent interference immunity, and inherent coexistence with WIFI. The IC contains all the necessary radio transceiver and digital baseband circuitry to form a complete digital wireless node without the need for external processing as well as including power management and analog circuitry. The IC is able to support both the lower and upper bands of 5GHz band RF spectrum, enabling worldwide coverage. The highly integrated nature of the AV5100 transceiver IC results in few external components being required for the ATM210 module design. 2 printed PCB antennas are used to achieve increased range, and to achieve antenna spatial diversity. The extended-range RF path consists of the antennas, associated tuning components, shield can, the RF switch, and two baluns, one connected to each of the RF input/output ports on the AV5100 IC. A 16MHz crystal oscillator generates the AV5100 fundamental system clock used as the basis for all RF and digital audio clocks. A 2Mb flash memory chip is used to store the modules application firmware. The AV5100 is able to boot from internal ROM upon first power up, which enables programming the flash chip with the application firmware through USB. In addition, Over-the-air Firmware upgrade capability can be enabled through the application firmware. The module can be controlled from an external host device via the I2C Slave or the SPI Slave data interfaces. The I2C master port allows the module to control other system audio devices such as a sub-woofer amplifier system without having to add another MCU to the product design. Up to 9 additional GPIOs are available on the ATM210 module (not including I2C and I2S signals) for implementing different UI features on the target application. The ATM210 module is powered from +5V supply input and the internal AV5100 IC is powering the internal +3.3V output LDO. The ATM210 module is available in two variations; digital input transmitter or digital output receiver. There are three available I2S digital audio data inputs/outputs, each of these can be configured to operate as either a master or a slave depending on the application, the I2S ports can operate simultaneously as either inputs or outputs. When configured as slaves, the I2S inputs/outputs can be independently clocked by up to two external masters. In addition, MCLK can be output from the module to provide a reference clock source to an external ADC or DAC. MCLK can also be input to the module to provide a reference clock from an external source. 5 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver The hardware for the audio input (transmit) and audio output (receive) versions of the module is identical and only the firmware loaded onto the module determines its function. ATM210 REV: 00 Features Product Size
- Module Size (mm): 40.4 (W) X 26.0 (L) X 3.2 (H)
-
-
- Antenna Type : PCB Printed Antenna PCB size (mm): 40.0 (W) X 2.6.0 (L) x 1.1 (H) Shield can (mm): 24.7 (W) X 21.9 (L) X 2.0(H) Audio Interfaces
-
I2S Digital Input/Output interface with >93dB end-to-end digital audio path Frequency range : 5.15~5.25GHz, 5725-5.825 GHz, continuous dynamic frequency selection Low, fixed latency (14.8ms typ. for stereo) 3Mbps OTA data rate Multiple OTA audio configurations Forward error correction coding, error detection, and audio-specific error concealment Auto-search/sync and dynamic channel selection Capability to detect and avoid wideband interferences such as 5GHz band WLAN Sample rate converter: Support for 32 - 96kHz input sample rates Dual printed PCB diversity antennas for multipath and fading migrations Wireless Range (typ.)
-
LOS (Line of Sight) range : <110m Control interfaces: I2C, SPI Up to 9 additional GPIOs Customizable firmware for simple, low-cost, sub-woofer amplifier implementations Dual printed PCB diversity antennas for multipath and fading mitigation RF parts can-shield 24pin FPC connector To be certified FCC/IC & CE compliance Applications Wireless Subwoofers Stereo Wireless Rear Speakers Soundbar / Audio Video Receiver / Home theater system Mono/Stereo Audio Channel Transmission 6 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver 5. Electrical Specifications 5-1. Absolute Maximum Ratings ATM210 REV: 00 Absolute Maximum Ratings (AMR) are stress ratings only. AMR corresponds to the maximum value that can be applied without leading to instantaneous or very short-term unrecoverable hard failure (destructive breakdown). Stresses beyond those listed under AMR may cause permanent damage to the device. Functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Range is not implied. Exposure to absolute-maximum-rated conditions for extended periods may adversely affect device reliability. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified. CONDITION
+5V Supply Voltage Input Input Voltage Range Digital Inputs Input Voltage Range Analog Inputs Operating Temperature Storage Temperature Static Discharge Voltage*
Notes;
MIN
-0.3V
-0.3V
-0.3V
-40C
-40C TBD MAX 6.0V 3.6V 3.6V
+85C
+85C TBD
* System level ESD : IEC 61000-4-2; C = 150pF, R = 330 5-2. Recommended operating Range PARAMETER VDD, +5V Supply pin voltage Ambient Temperature (TA) RESET pin hold time Power Supply Rise Time (to 3.0V) MIN 4.5 0 10 0 TYP 5.0 MAX UNIT 5.5 60 10 V C ms ms 5-3. Electrical Characteristics DC Typical specifications at TA = 25C, VDD = 5.0V PARAMETER CONDITION MIN TYP MAX UNIT Supply Current (IVDDA) Shutdown (chip disabled) Standby (also USB suspend) 1 TBD uA mA 7 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver CMOS I/O Logic Levels VDDIO 3.3V Continuous TX Linked status for TX Searching for TX Continuous RX Linked status for RX Searching for RX Input Voltage Logic Low, VIL Input Voltage Logic High, VIH VDDIO -
0.6V Output Voltage Logic Low, VOL Output Voltage Logic High, VOH VDDIO -
0.3V ATM210 REV: 00 110 49 46 110 93 93 0.6 0.3 mA V 5-4. Electrical Characteristics RF TX Operating Conditions: VDD = 4.5 to 5.5V, TA = 0C to +60 C, RF Freq = 5725-5825MHz, measured to the RF conducted 2 ports. Typical specifications at TA = 25C, VDD = 5.0V PARAMETER CONDITION RF Channel Frequency Range Channel Bandwidth [OBW]
Low band High band SSC (Single Sub-Carrier) DSC (Dual Sub-Carrier) TX Output power TX Spurious(harmonic) SSC / Low band DSC / Low band SSC / High band DSC / High band 2nd 3rd RF I/O Impedance ANT0, ANT1 LO leakage MIN 5150 5725 TYP 2 4 5 4 7 6 50
-20 MAX 5250 5825
-55
-55 UNIT MHz MHz dBm dBm dBm dBm ohm dBc 8 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver 5-5. Electrical Characteristics RF RX ATM210 REV: 00 Operating Conditions: VDD = 4.5 to 5.5V, TA = 0C to +60 C, RF Freq = 5725-5825MHz, measured to the RF conducted 2 ports. Typical specifications at TA = 25C, VDD = 5.0V PARAMETER CONDITION RF Channel Frequency Range Low band High band RX Sensitivity*
Max input signal Out-of-band blocker level Spurious RF outputs SSC (Single Sub-Carrier) DSC (Dual Sub-Carrier) LNA = low gain mode, min IF gain
<5150 MHz, >5850 MHz 2400-2483.5 MHz 5150-5850 MHz
<5150 MHz, >5850 MHz ANT0, ANT1 RF I/O Impedance
* The sensitivity been defined with BER <= 0.002. 5-6. Electrical Characteristics RF PLL MIN 5150 5725 TYP
-89
-86
-5
-45
-20 50 MAX 5250 5825 UNIT MHz TBD TBD dBm dBm ohm Operating Conditions: VDD = 4.5 to 5.5V, TA = 0C to +60 C, RF Freq = 5725-5825MHz, measured relative to the RF balun single-ended I/O. Typical specifications at TA = 25C, VDD = 5.0V PARAMETER CONDITION RF Channel Frequency Range Low band High band RF Channel frequency resolution (raster) Local Frequency error Crystal Oscillator Frequency External crystal RF I/O Impedance ANT0, ANT1 MIN 5150 5725 TYP 1 5 16 50 MAX 5250 5825 10 UNIT MHz MHz ppm MHz ohm 5-7. Electrical Characteristics Audio C/CS PARAMETER CONDITION Frequency Response (-3dB) 16bit audio, 11KSps over-the-air sample rate MIN 20 TYP MAX UNIT 5K Hz 9 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver ATM210 REV: 00 16bit audio, 14.8KSps over-the-air sample rate 16bit audio, 14.8KSps over-the-air sample rate 16bit audio, 14.8KSps over-the-air sample rate 16bit audio, 14.8KSps over-the-air sample rate 0dB Input / Output Gain 20 20 20 20
+/- 0.2 6.5K 10K 13K 20K Gain Flatness SNR I2S Input / Output 93*
THD+N
* 16bit audio, all OTA sample rate. OTA 12-bit path for voice is possible, but will limit the SNR to 72dB 94 5-8. AV5100 Rate Converter Characteristics dB dB dB SRC Block Input Rates Output Rates SNR (dB) SRC BW (-3dB) SRC 0
(Audio) SRC 1
(LFE) I2S 32-96K USB 8K-48K ECU (TX) 11K 14.8K 22K 29.6K 44K I2S 32-96K USB 8K-48K ECU (TX) 11K 14.8K 22K 29.6K 44K I2S Maser : 48K Slave : 44.1K-96K ECU (TX) 11K 14.8K 22K 29.6K 44K I2S Maser : 48K Slave : 44.1K-96K ECU (TX) 11K 14.8K 22K 29.6K 44K All rate support 16bit, > 93dB All rate support 16bit, > 93dB Actual bandwidth is dependent on the lower of the input or output rate Output BW vs OTA 11K = 5KHz 14.8K = 6.5KHz 22K = 10KHz 29.6K = 13KHz 44K = 20KHz Actual bandwidth is dependent on the lower of the input or output rate Output BW vs OTA 11K = 5KHz 14.8K = 6.5KHz 22K = 10KHz 29.6K = 13KHz 44K = 20KHz 10 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver SRC 2
(Audio) I2S 32-96K USB 8K-48K ECU (TX) 14.8K 5-9. I2S Communication Interface Timing I2S Maser : 48K Slave : 44.1K-96K USB 8K-48K ECU (TX) 14.8K All rate support 16bit, > 93dB, but the OTA 12bit path will limit SNR to 72dB ATM210 REV: 00 Actual bandwidth is dependent on the lower of the input or output rate Output BW vs OTA 11K = 5KHz 14.8K = 6.5KHz 22K = 10KHz 29.6K = 13KHz 44K = 20KHz I2S Interface Timing VL VL T TLO THI TR TF TSu Parameter Low voltage level High voltage level Clock period Clock low period Clock high period Rise time Fall time Setup time MIN
-0.3 2.4 0.4T 0.4T 25 TYP 0 3.3 325.5 MAX 0.4 3.6 0.6T 0.6T 50 50 UNIT Notes V V ns ns ns ns 1/3.072MHz 11 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver THd TOd Hold time Output delay Bit clocks/Word clock 25
-25 I2S protocol is I2S Justified as shown below. 64 25 ns ns ATM210 REV: 00
*The timing specified for the rise and fall times represents the edge rates on the module itself. The rise and fall times of the I2S signals are determined by ESD/EMI mitigation components on the modules, as well as external loading, and will be higher than the specified numbers 5-10. I2C Slave Communication Interface Timing The ATM210 has both I2C slave and master interfaces available with their respective pins S_SCL, S_SDA and M_SCL, M_SDA. The interfaces operate in I2C fast-mode and can receive and transmit at up to 400 kbit/s. Bytes are 8 bits long and are transferred with the most significant bit (MSB) first. Each byte has to be followed by an acknowledge bit. The SWA52 will apply clock-stopping (by holding the clock line S_SCL LOW to force the master into a wait state) if necessary due to internal high-priority tasks. The slave/master interface can be used both for writing (e.g. sending commands) or reading (e.g. requesting status). An additional GPIO pin on the SWA52 (Ex. GPIO24), can be used to notify the I2C master when a pending message is ready to be sent. The ATM210 slave interface responds to the 7-bit slave address 1000000 (0x40) as shown in picture below. 12 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver ATM210 REV: 00 I2C Slave Interface Timing (Fast-Mode) Parameter Low level input voltage VIL VIH VOH tof tSP High level input voltage Low level output voltage At 1mA sink current Output fall time from VIHmin to VILmax with a bus capacitance from 10pF to 400pF Pulse width of spike which must be suppressed by the input filter S_SCL clock frequency Low period of the S_SCL clock High period of the S-SCL clock fSCL tLOW THIGH tHD;DAT Data hold time TSU;DAT Data set-up time MAX UNIT 0.8 3.6 0.4 250 50 400 V V V ns ns KHz ns ns ns ns MIN
-0.3 2.0 0 0 0 0 1.3 0.6 100 100 13 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver 6. I/O Connector Pin Description I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O GND GND I/O I/O I/O I/O ATM210 REV: 00 ATM210-TX Pin Description ATM210-RX Pin Description GPIO or SPI slave chip select GPIO or SPI slave serial clock GPIO, I2C slave serial data or SPI slave data In GPIO, I2C slave serial clock or SPI slave data out GPIO or I2C master serial data GPIO or I2C master serial clock GPIO or Link_LED output GPIO or SPI slave chip select GPIO or SPI slave serial clock GPIO, I2C slave serial data or SPI slave data In GPIO, I2C slave serial clock or SPI slave data out GPIO or I2C master serial data GPIO or I2C master serial clock GPIO or Link_LED output GPIO or Input from PAIR Button GPIO or Input from PAIR Button GPIO or I2S port1 bit clock GPIO or I2S port1 word clock GPIO or Master clock out GPIO or I2S port1 bit clock GPIO or I2S port1 word clock GPIO or Master clock out GND GPIO or I2S port0 bit clock GPIO or I2S port0 word clock GPIO or I2S port0 audio data GPIO or I2S port1 audio data GPIO, I2S port2 audio data or Chip enable GPIO or USB data plus GPIO or USB data plus GPIO Reset signal active low GND
+5.0V input supply voltage
+5.0V input supply voltage GPIO or I2S port0 bit clock GPIO or I2S port0 word clock GPIO or I2S port0 audio data GPIO or I2S port1 audio data GPIO, I2S port2 audio data or Chip enable GPIO or USB data plus GPIO or USB data plus GPIO Reset signal active low I/O I/O I/O I/O I GND GND Supply +5.0V input supply voltage Supply +5.0V input supply voltage Pin #1 Pin #24 JUN 10,2019 14 /20 No Pin Name 1 2 3 4 GPIO2 /S_SSB GPIO3 /S_SCLK GPIO4 /
I2CS_SDA/S_MOSI GPIO5 /
I2CS_SCL/S_MISO GPIO16 / I2CM_SDA GPIO17 / I2CM_SCL GPIO20 /LINK_LED GPIO21/ PAIR GPIO18 /BCK1 5 6 7 8 9 10 GPIO19 / WCLK1 11 GPIO10 /MCLK 12 GND 13 GPIO11 / BCK0 14 GPIO12 /WCLK0 15 GPIO13 /ADAT0 16 GPIO14 / ADAT1 17 GPIO15 / ADAT2/CEN 18 GPIO22 / D+
19 GPIO23 / D-
20 GPIO24 21 22 GND VDD 23 24 VDD RESETN_EXT PBA RF Module 5GHz Wireless Audio Transceiver 7. Mechanical Specifications ATM210 REV: 00 7-1. Module dimension 7-2. Antenna dimension 15 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver 8. Label Specification ATM210 TX Module Label ATM210 REV: 00 ATM210 RX Module Label 16 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver 9. Certificate Statement ATM210 REV: 00 FCC & IC Statement This AUDIO TRANSCEIVER has been granted modular approval for mobile applications. OEM integrators for host products may use the module in their final products without additional FCC / IC (Industry Canada) certification if they meet the following conditions. Otherwise, additional FCC / IC approvals must be obtained. The host product with the module installed must be evaluated for simultaneous transmission requirements. The users manual for the host product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC / IC RF exposure guidelines. To comply with FCC / IC regulations limiting both maximum RF output power and human exposure to RF radiation, use this module only with the included onboard antenna. A label must be affixed to the outside of the host product with the following statements:
Product Name : AUDIO TRANSCEIVER Contains FCC ID: 2AS8LATM210 Contains IC: 25119-ATM210 The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a different circuit from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help. 17 /20 JUN 10,2019 ATM210 REV: 00 PBA RF Module 5GHz Wireless Audio Transceiver Device Classifications Since host devices vary widely with design features and configurations module integrators shall follow the guidelines below regarding device classification and simultaneous transmission, and seek guidance from their preferred regulatory test lab to determine how regulatory guidelines will impact the device compliance. Proactive management of the regulatory process will minimize unexpected schedule delays and costs due to unplanned testing activities. The module integrator must determine the minimum distance required between their host device and the users body. The FCC provides device classification definitions to assist in making the correct determination. Note that these classifications are guidelines only; strict adherence to a device classification may not satisfy the regulatory requirement as near-body device design details may vary widely. Your preferred test lab will be able to assist in determining the appropriate device category for your host product and if a KDB or PBA must be submitted to the FCC. Note, the module you are using has been granted modular approval for mobile applications. Portable applications may require further RF exposure (SAR) evaluations. It is also likely that the host / module combination will need to undergo testing for FCC Part 15 regardless of the device classification. Your preferred test lab will be able to assist in determining the exact tests which are required on the host / module combination. FCC Definitions Portable: (2.1093) A portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is / are within 20 centimeters of the body of the user. Mobile: (2.1091) (b) A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitters radiating structure(s) and the body of the user or nearby persons. Per 2.1091d(d)(4) In some cases (for example, modular or desktop transmitters), the potential conditions of use of a device may not allow easy classification of that device as either Mobile or Portable. In these cases, applicants are responsible for determining minimum distances for compliance for the intended use and installation of the device based on evaluation of either specific absorption rate (SAR), field strength, or power density, whichever is most appropriate. Simultaneous Transmission Evaluation This module has not been evaluated or approved for simultaneous transmission as it is impossible to determine the exact multi-transmission scenario that a host manufacturer may choose. Any simultaneous transmission condition established through module integration into a host product must be evaluated per the requirements in KDB447498D01(8) and KDB616217D01,D03 (for laptop, notebook, netbook, and tablet applications). These requirements include, but are not limited to:
host devices without further testing or certification when:
Or have been specified in the application filing of at least one of the certified transmitters within the host device. In addition, when transmitters certified for portable use are incorporated in a mobile host device, the antenna(s) must be >5 cm from all other simultaneous transmitting antennas. Transmitters and modules certified for mobile or portable exposure conditions can be incorporated in mobile Antenna separation distance and MPE compliance requirements for ALL simultaneous transmitting antennas All antennas in the final product must be at least 20 cm from users and nearby persons. The closest separation among all simultaneous transmitting antennas is >20 cm, 18 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver ATM210 REV: 00 OEM Instruction Manual Content Consistent with 2.909(a), the following text must be included within the users manual or operator instruction guide for the final commercial product (OEM-specific content is displayed in italics.) Operating Requirements and Conditions:
The design of ATM210 complies with U.S. Federal Communications Commission (FCC) guidelines respecting safety levels of radio frequency (RF) exposure for Mobile devices. Note: In the case where the Host / Module combination has been re-certified the FCCID shall appear in the product manual as follows:
FCCID: 2AS8LATM210 Mobile Device RF Exposure Statement (If Applicable):
RF Exposure - This device is only authorized for use in a mobile application. At least 20 cm of separation distance between the transmitting antenna device and the user's body must be maintained at all times. Caution Statement for Modifications:
Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user s authority to operate the equipment. FCC Part 15 Statement (Only Include if FCC Part 15 is Required on the End Product):
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. (OEM must follow Part 15 guidelines (15.105 and 15.19) to determine additional statements required in this section for their device class) Note 2 : This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions. 1) This device may not cause harmful interference, and 2) This device must accept any interference, including interference that may cause undesired operation of the device. a. That module is limited to OEM installation ONLY. b. That OEM integrators are responsible for ensuring that the end-user has no manual instructions to remove or install module. c. That module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). d. That separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations. e. That grantee shall provide guidance to the host manufacturer for compliance with Part 15 subpart B requirements. 19 /20 JUN 10,2019 PBA RF Module 5GHz Wireless Audio Transceiver ATM210 REV: 00 Information This device complies with Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicable aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles les radiolectriques (RF) de la FCC lignes directrices dexposition et dexposition aux frequencies radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation du dbit dabsorption spcifique (DAS). CE Statement Hereby, SEONG JI INDUSTRIAL CO., LTD declares that the radio equipment type AUDIO TRANSCEIVER is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the providing datasheet or approval sheet. The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. This device must not be collocated or operating in conjunction with any other antenna or transmitter. 20 /20 JUN 10,2019