Title :Information DocumentNO.Date0. GENERAL0.1. MakeSEOYON ELECTRONICS Co.,Ltd.0.2. Model No.- Transmitter : FOB-SMART KEY SYEC3FOB1611- Receiver : SMART KEY SYSTEM0.3. Name and address of manufacturerSEOYON ELECTRONICS Co.,Ltd.424, Sinwon-ro, Danwon-gu, Ansan-si, Gyeonggi-do, Korea0.4. Address of assembly plantSEOYON ELECTRONICS Co.,Ltd.424, Sinwon-ro, Danwon-gu, Ansan-si, Gyeonggi-do, KoreaSHT/SHTS : 2/11 Title :Information DocumentNO.Date2.PRODUCT SPECIFICATIONSHT/SHTS : 3/112.1Scope of RKE, passive entry control, passive start control in SMART Key system.2.1.1FOB KEY : It has the functions for passive entry and passive start includingRKE functions. It also has the TP for emergency authentication for passive start2.1.2SMART Key system : It is an ECU to control the whole smart key system.It has the functions such as passive entry control, passive start control, RKE functions.2.2SPECIFICATIONS2.2.1FOB KEY2.2.2RECEIVERITEMSPECIFICATIONRated supply voltageDC 3VOperating voltage rangeDC 2.5 ~ 3.2VOperating temperature range- 10 ~ + 60 with BatteryStorage temperature range- 40 ~ + 85 without BatteryModulationFSKFrequency433.92MHzCodeRolling Code(Hopping Algorithm)Electric field strength10mW (433.92MHz)Battery life2 Year(10Times/Day)(Lithium 3V 1EA)ItemSpecificationRated Supply VoltageDC 12VOperating VoltageDC 9 ~ 16VOperating Temperature- 35 ~ + 75Max Humidity95%Standby CurrentBelow than 5.5mA(in alarm setting condition) Title :Information DocumentNO.Date2.3Operating summary-RKETRANSMITTER's button is pushed.TRANSMITTER sends the code by radio frequency.RECEIVER gets the code and decodes it.RECEIVER judges the code whether it is right code or not.RECEIVER checks door lock or unlock, trunk state.RECEIVER drives the actuator.- Passive Startthe SSB button of SMK is pressed to start the engine.SHT/SHTS : 4/11The indoor ANT of the car transmits the code via the Low Frequency.Fob(receiver) decrypts the received code from SMK.Fob transmits the code via radio frequency.SMK should check the boot state.SMK controls a start-up operation and the transition of supply power.2.3.1LOCK & UNLOCKIf LOCK or UNLOCK button is pushed for less than 1 sec,then TRANSMITTER sends the LOCK or UNLOCK DATA.If TRUNK button is pushed for more than 1 sec, thenTRANSMITTER sends the TRUNK DATA.2.4 CautionDanger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type recommended by themanufacturer.Dispose of used batteries according to the manufacturer's instructions. Information Document Information Document rmation Document hes Title :Info Information DocumentNO.DateSHT/SHTS : 5/113.USER MANUAL3.1ITEM : SMK system- This system is SMK and inculdes RKE.- RKE in SMK system is intended for auto door lock or unlock or TRUNK in vehicle. - This SMK system is to be installde on motor vehicles as *OE item.*OE : Original Equipment.*SMK : Smart Key System*RKE : Remote Keyless Entry.3.2SYSTEM CONSTRUCTION3.2.1SYSTEM IN VEHICLERadio Frequency(433.92MHz)Low Frequency(134.2KHz)ANTENNA BATTERYSMK LF ANTSSB3.2.2SYSTEM FOR TESTRadio Frequency(433.92MHz)Low Frequency(134.2KHz)ANTENNA BATTERYSMK LF ANTSSBConnect the 12V power supply and turn on the switchPressing the white tact switch, LF signal is transmitted and FOB LED and SMK LED is flaWhen the tact switch is pressed repeatively, FOB LED and SMK LED is flahes, repeatively. * It shows the status of operation through the LED used. FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions :
(1) This Device may not cause harmful interface, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. WARNING Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. CAUTION : Exposure to Radio Frequency Radiation. Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit.