U S E R M A N U A L PAGE 1/4 SPEC NO. ESTABLISHED BY SEOYON ELECTRONICS 1. GENERAL INFORMATION 2. ELECTRICAL CHARACTERISTICS
-
Rev.NO RELEASED DESCRIPTION OF CHANGE REL. DATE 2017.10.17 REFERENCE ALL 2017.10.17 H S LIM CHANGE PAGE SORT PREPARED REV. DATE CHECKED REV. BY APPROVED Original archive
(PLM SYSTEM) APPR OVAL H S LIM R H HWANG J H LEE DSF-4-02-01A-1 SEOYON ELECTRONICS CO., LTD. A4(210x297) U S E R M A N U A L SPEC NO SHT/SHTS 2/4 Contents list page 1. GENERAL INFORMATION ........................................................................................................................ 1.1. Description of WPC UNIT ........................................................................... 1.2. System overview ...................................................................................... 2. ELECTRICAL CHARACTERISTICS ................................................................. 2.1. Operating characteristics of MP .................................................................. 2.2. Operating characteristics of MP+NFC ........................................................... 2.3 UNIT Inout/OutputInterface......................................................................... 1. GENERAL INFORMATION 1.1Description of WPC UNIT WPC UNIT provides the following functions. MAX 15W Wireless Charging NFC Vechicle Start status Wireless Charging : 119.6kHz NFC Reader : 13.56MHz Brand name : HYUNDAI, KIA Model name : SYECNWPC1903 Picture 1: System configuration U S E R M A N U A L SPEC NO SHT/SHTS 3/4 1.2 System overview Wireless charging controller <LP, MP> - System for charging mobile phone wirelessly in vehicle using electromagnetic induction between coils After inputting IGN1 power, the reception coil (cell phone RX Coil) Confirmation of non-mobile NFC mounting via NFC Multi Tagging <MP + NFC>
(TX side charging pad: wireless charger side) Current flows in the transmission coil The magnetic field generated by the current of the transmission coil is guided to the receiving coil and induction current is generated in the receiving coil The charging current starts to be charged through PMIC (Power module IC) of mobile phone NFC Communication Controller <MP + NFC> - Vehicle start, key registration, and vehicle information transmission / reception device through mutual communication with NFC (near field communication) installed in mobile phone and ECU. After inputting B + power, put Smart Phone on top of ECU When charging C_WPCNFCCmd = 0x01 (NFCSearchingOnHCE) from the authentication unit, stop wireless charging && NFC Start PhoneKeyAuth Mode (SmartPhone WPC IAU AUTH certification) RTC SYNC MODE (RTC synchronization) CertificateChain SYNC MODE (Certificate Synchronization) PhoneKey Sync MODE MODE (Synchronize PhoneKey and Spare Key) When C_WPCNFCCmd = 0x02 (NFC Searching Off) is input from the authentication unit NFC Mode Stop &&
When IGN1 is ON, Wireless charging Start 2 ELECTRICAL CHARACTERISTICS 2.1 Operating characteristics of MP Item Rated Supply Voltage Operating Voltage Operating Temperature Storage temperature range MP<WPC> Frequency Specification DC 12V DC 9 ~ 16V
- 30 ~ + 75
- 40 ~ + 85 119.6kHz U S E R M A N U A L SPEC NO SHT/SHTS 4/4 Standby Current Below than 1mA Table 1: Electrical characteristics of MP 2.2 Operating characteristics of MP+NFC Item Rated Supply Voltage Operating Voltage Operating Temperature Storage temperature range MP<WPC> Frequency NFC Frequency Standby Current Specification DC 12V DC 9 ~ 16V
- 30 ~ + 75
- 40 ~ + 85 119.6kHz 13.56MHz Below than 1mA Table 2: Electrical characteristics of MP+NFC 2.3 UNIT Input/Output Interface Pin No. Description Reference 1 2 3 4 5 6 7 8 9 10 11 12 GND GND WC_AMBER_IND_OUT WC_GREEN_IND_OUT B_CAN_LOW B_CAN_HIGH NC AUTH_CAN_LOW AUTH_CAN_HIGH NC IGN1 BAT+
Este produto est homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolu o n. 242/2000 e atende aos requisitos t cnicos aplicados. Para maiores informa es, consulte o site da ANATEL www.anatel.gov.br FCC warning statement:
15.19
. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21
- Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment.
- This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
- End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. FCC/ IC RF Radiation Exposure Statement:
This equipment complies with FCC/ ISED RF radiation exposure limits set forth for an uncontrolled environment for body-worn configuration in direct contact to the phantom. This device complies with FCC/ ISED radiation exposure limits set forth for an uncontrolled environment. IC warning statement:
RSS-Gen Issue 4 8.4 This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Co-located This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.