FCC ID: P27SCD2R0 SCD2R0-29 Wireless FHD Doorbell Camera Setup Guide FCC ID: P27SCD2R0 Copyright 2019. All Rights Reserved. Document Version: 1.1 FCC ID: P27SCD2R0 Table of Contents Chapter 1 Introduction .......................................................................................................... 1 Package Contents .............................................................................................................. 1 Physical Details .................................................................................................................. 2 Chapter 2 Setup ...................................................................................................................... 5 System Requirements ........................................................................................................ 5 Installation ......................................................................................................................... 5 Chapter 3 Hardware Installation ......................................................................................... 8 Overview ............................................................................................................................ 8 Power Kit Installation ..................................................................................................... 11 Always On Bracket Installation (Optional) ................................................................... 12 Battery Pack Installation (Optional) ..............................................................................13 Appendix A Specifications ................................................................................................. 14 Wireless Doorbell Camera .............................................................................................. 14 Regulatory Approvals ..................................................................................................... 15 Chapter 1 Introduction FCC ID: P27SCD2R0 1 This section provides information about the Doorbell Camera features, components and capabilities.. Package Contents The following items should be included: If any of these items are damaged or missing, please contact your dealer immediately. 1. Doorbell Camera x 1 2. Screw/Anchor x 2 3. Always On Bracket x 1 (Optional, may not included in the package) 1 FCC ID: P27SCD2R0 Physical Details The SCD2R0-29 supports both analog and digital chimes within 8-24 AC voltage range. The operation temperature of SCD2R0-29 with regular mounting bracket and Battery pack is 4F to 122F (20C to 50C). As to SCD2R0-29 with Always on bracket, the operating temperature is 4F to 104F. (20C to 40C) on day mode and 4F to 95F. (20C to 35C) on night mode. Note:
1. The Doorbell internal battery will not be charged when the temperature is < 32F (0C) and > 122F (50C) or discharge when internal temperature is < -4F (-20C) and >138F
(60C) 2. The battery of Battery Pack can only be charged 0 to 35, 85% RH Max, and discharged -20 to 50, 85% RH Max Front Panel Light Sensor Microphone PIR Sensor Doorbell/WPS Pairing Button This is hardware sensor to detect LUX. The built-in microphone is useful for bi-direction voice conversation. This is hardware sensor to detect motion. Doorbell/WPS Button has two functions:
WPS Pin Code Mode: When doorbell button is held down for more than 3 seconds, the doorbell camera will be in WPS Pin Code Mode. WPS PBC Mode. When doorbell button is held down for less than 3 seconds, the Wireless HD Doorbell Camera will be in the WPS PBC mode (Auto link mode). Note: When Wi-Fi connection is established, the WPS function is disabled. Doorbell Mode: Press the button to ring the door chime. 2 Rear Panel Reset Button FCC ID: P27SCD2R0 When pressed and held over 10 seconds, the LED will be solid amber, which means the settings of camera will be set to their default values. Use this switch to turn on/off the device. On/Off Switch Micro USB Connector This connector is used for charging the power. Connect the supplied Micro-USB cable to this port. 3 LED Activity & Behavior Doorbell Activity LED Color LED Behavior Factory Reset Amber Solid WPS Pairing
(PIN Code Mode) Amber Blinking
(200ms) WPS Pairing
(PBC Mode) Amber Blinking
(500ms) WPS Failure Amber Solid
(5s) Network Connected
(Boot-up) Green Blinking
(500ms) FCC ID: P27SCD2R0 Description Press the reset button for 10 seconds to start this process. When doorbell button is held down for more than 3 seconds, the LED will start flashing amber indicating doorbell camera is trying to connect to your Wi-Fi network in Pin Code mode. When doorbell button is held down for less than 3 seconds, the LED will start flashing amber indicating doorbell camera is trying to connect to your Wi-Fi network in PBC mode. If doorbell camera falls during WPS enrollment, the LED will be solid on for 5 seconds. When the doorbell camera is trying to connect the network, LED color will change to blinking green. USB charge+
Battery < 80%
Blue Blinking
(1s) LED spinning blue indicates the camera is charging for power. PIR Triggered Blue Solid When PIR detects motion the LED will turn solid blue. Doorbell Button Press Intercom Blue Solid NA Green Whirling
(2s) Green LED will pulse between dim and medium intensity for two seconds while waiting for interactive session. 4 FCC ID: P27SCD2R0 2 Chapter 2 Setup This Chapter provides details on how to install and configure the Doorbell Camera. System Requirements A computer with Internet access You can use the following web browser while using a computer:
Internet Explorer 10 or later Firefox 3.5 or later Safari 3 or later (Mac OS X only) Chrome Microsoft Edge Installation 1. Power-Up and Check LED Turn on the switch on the rear side of the doorbell camera and wait for 20 seconds until the LED turns to flashing amber. Note: The internal battery supports about 40 minutes of operation. If you dont see the camera powering up, please charge the doorbell camera via Micro USB cable with USB charger (DC5V1A or above ) for 45 minutes before installation. 2. Add the Doorbell Camera to your network. a. Doorbell will detect the Wireless device (AP or router) which is Disable the Wireless Security automatically. The default Wireless settings are:
Mode: Infrastructure SSID: ANY Wireless Security: Disabled Domain: USA Channel No.: Auto 5 FCC ID: P27SCD2R0 b. 1) WPS PBC ModePress the Doorbell button for less than 3 second and on your Wireless device (AP or router) as well to establish a wireless connection automatically. The wireless connection is successful when the Green LED blinking. 2) WPS Pin Code ModeKey in the PIN code of Doorbells back label on the Client PIN code of AP, and then held down Doorbell button for more than 3 seconds, the Doorbell Camera will be in the WPS Pin Code mode.
(Please make sure if your AP or router support the WPS Pin code mode) Note: Once Doorbell ever connected to AP by WPS or GUI configuration, then the push button is no longer for WPS function. Please restore the Doorbell to factory default on working mode, after then try the WPS again to connect another AP. c. Obtain the IP Address of Doorbell on Wireless device (AP or router) device page. And start the Internet Explorer. After then enter the IP Address of Doorbell on the Address box of Internet Explorer (ex. http://192.168.1.223) d. When you connect, the following screen will be displayed. e. Click View Video. f. The first time you connect to the camera, you will be prompted to install decoders. Choose "I accept the terms of the license agreement" and click "OK". Note: The options can only be configured while using IE browser. Other browsers can just view the video rather than configuration. 6 FCC ID: P27SCD2R0 g. Video will start playing automatically. There may be a delay of a few seconds while the video stream is buffered. h. If the Administrator has restricted access to known users, you will then be prompted for a username and password. Enter the name and password assigned to you by the Doorbell administrator. The default log in Administration:
User Name: administrator Password: Blank i. Access the Administration for more Doorbell settings on SCD2R0-29 GUI. 3. Switch to analog or digital chime according to your existing doorbell in the process.
(The default chime which SCD2R0-29 support is analog type; the customers are required to develop this feature on the App) 7 FCC ID: P27SCD2R0 If your existing doorbell produces an electronic sound that is programmable and comes in the form of a unique sound, it's a digital chime. If it has a traditional "ding dong" sound, it's a compatible analog chime. 4. Complete the pairing process and unplug the Micro USB cable from the Doorbell Camera. 5. Identify the location for Mounting the Doorbell Camera The recommended installation height of the Doorbell Camera is about 130~150cm from the ground. Please refer to Chapter 3 Hardware Installation for more details. Chapter 3 Hardware Installation 3 This chapter covers the most likely problems and their solutions. Overview Note: Ensure the camera is configured and enrolled in AP or router before permanently mounting. Note: If SCD2R0-29 is using for engineering develop purpose, it is available to use Mirco USB cable to charge the battery for replacing the transformer. And doorbell does not require attaching with the chimer. 1. Check the voltage at the chimer to ensure voltage is between 8 ~ 24V AC. 2. Turn off the breaker circuit before disconnecting legacy doorbell button. 3. Unscrew the legacy doorbell to locate two power wires. (The recommended installation height is between 47 -60 inches.) 8 FCC ID: P27SCD2R0 4. Choose either the Always On bracket or the regular mounting bracket that will cover the hole of the legacy doorbell button. Please check Always On Bracket Installation section for more details 5. Connect the power wires from the existing doorbell to the screw terminals of the bracket. 6. Secure the bracket with screws. Note: Install the anchors if necessary. The provided lever can be used for measuring angles to prevent inclination. 7. Attach the doorbell camera to the mounting bracket. Make sure the doorbell camera is firmly fixed and working properly. Caution: To avoid damaging the rubber seal of the pogo pins, please attach the camera to the mounting bracket flush. Mounting bracket should lay flat against the wall. Over torqueing can warp the bracket and cause it to lose contact with pins. 9 FCC ID: P27SCD2R0 8. Turn on the breaker circuit. 9. Check that the chime is working normally by pushing the doorbell button. If the AC wires are not connected properly, the LED will blink amber every 5 seconds. 10 FCC ID: P27SCD2R0 Power Kit Installation The Power Kit included with the doorbell camera is a small device, which support Doorbell with any kinds of analog and digital chime usage by going between the doorbell transformers and chime wiring. Note: Before removing or attaching wires to your original bell, be sure that the power is turned off at the breaker box. Consult a licensed electrician if needed. 1. 2. 3. Turn off the circuit breaker for the indoor chimer. Remove the cover from the indoor chimer. Loosen the "Front" and "Trans" terminal screws on the indoor chimer. 4. Connect white wire from the Power Kit to the Front terminal, and the black wire to the Trans terminal, leaving the existing doorbell wires in place. Then, re-tighten the screws. 5. Position the Power Kit inside your indoor chimer, away from any moving parts. Use the adhesive (foam tap) on the back of the Power Kit to fix it in place, if desired. 6. Attach the cover back to the indoor chimer, and turn the power on at the breaker. 11 FCC ID: P27SCD2R0 Always On Bracket Installation (Optional) The Always On bracket (may not included in the package) can only be installed with mechanical doorbell chimes (AC16V~24V). In this configuration, the doorbell camera will be in always on mode, which brings back the 5 second pre-buffer, connects live view faster, and removes the need for the internal battery to be charged. 1. Use the always on bracket that will cover the hole of the legacy doorbell button. 2. Connect the power wires from the existing doorbell to the screw terminals of the bracket. 3. Secure the bracket with screws. 12 FCC ID: P27SCD2R0 4. Attach the doorbell camera to the mounting bracket. Make sure the doorbell camera is firmly fixed and working properly. Caution: To avoid damaging the rubber seal of the pogo pins, please attach the camera to the mounting bracket flush. Mounting bracket should lay flat against the wall. Over torqueing can warp the bracket and cause it to lose contact with pins. Specification LED Waterproof Enclosure Pogo Pin Power LED x 1 (Green) IP65 2 x 4 (8 Pin) AC16~24V Doorbell Attached Always on Bracket LED Activity & Behavior Doorbell Activity LED Color LED Intensity LED Behavior Description Blue Dim Solid After connected to the doorbell, LED color will turn to dim blue. Bracket Connected 13 Appendix A Specifications A Wireless Doorbell Camera Model Dimensions
(H x W x D) Operating Temperature Mounting Bracket and Battery Pack mode: -20C to 50C Wireless 2-Way Doorbell Camera 126 mm * 42.7mm * 35.2mm (4.96 x 1.68 x 1.39)
-20C to 40C ( Day Mode)
-20C to 35C ( Night Mode) Always On Bracket mode:
-20 C to 45 C TCP/IP, HTTP, HTTPS, DHCP, uPnP, NTP, RTP, RTCP, RTSP, DN 802.11 b/g/n 1 1 Built-in Microphone Doorbell/WPS Button x 1 Reset button x 1 1 built-in Microphone USB charger: DC 5V,1A Internal Battery Power : capacity 730mA Charging Temp : 0C to 20C Storage Temperature Network Protocols Wireless IR LED LED Microphone Button Speaker Power Adapter 14 Regulatory Approvals FCC Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
(Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. CE Approval CE Standards This product complies with the 99/5/EEC directives, including the following safety and EMC standards:
EN55022/24 CE Marking Warning This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 15