all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manual | photos | label |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 2.98 MiB | July 21 2015 | |||
1 |
|
Internal Photos | Internal Photos | 1.37 MiB | July 21 2015 | |||
1 |
|
External Photos | External Photos | 581.86 KiB | July 21 2015 | |||
1 |
|
Label | ID Label/Location Info | 1.31 MiB | July 21 2015 | |||
1 |
|
Agents Letter | Cover Letter(s) | 46.84 KiB | July 21 2015 | |||
1 | Antenna Details | Operational Description | July 21 2015 | confidential | ||||
1 | Antenna Details II | Operational Description | July 21 2015 | confidential | ||||
1 | Block Diagram | Block Diagram | July 21 2015 | confidential | ||||
1 |
|
Confidentiality Letter | Cover Letter(s) | 59.14 KiB | July 21 2015 | |||
1 |
|
DoC Letter | Cover Letter(s) | 51.20 KiB | July 21 2015 | |||
1 | Operating Description | Operational Description | July 21 2015 | confidential | ||||
1 |
|
RF Exposure Report | RF Exposure Info | 157.54 KiB | ||||
1 | Schematics | Schematics | July 21 2015 | confidential | ||||
1 |
|
Test Report | Test Report | 4.81 MiB | July 21 2015 | |||
1 |
|
Test Setup Photos | Test Setup Photos | 410.83 KiB | July 21 2015 | |||
1 |
|
Tune Up | Parts List/Tune Up Info | 21.12 KiB | July 21 2015 |
1 | User Manual | Users Manual | 2.98 MiB | July 21 2015 |
Sercomm ele ee tenis The following items should be included: If any of these items are damaged or missing, please contact your service provider immediately. HD iP Camera 1. Waterproof HD IP Camera x 1 O0C830 2. Stand x1
3. 3M DC Power Adapter x 1 eae
\ 3 oe i g W ro4
; y Saal 4. Screw/Anchor x 2 uy uy 5. DC In Rubber x 1 6. Rubber Cap x 1
SS SS SSS SSS : ;
Setup Guide 7. RJ-45 USB Cable x 1 (Only for paring, not suitable for outdoor usage) ee a Document Version: 1.0 Copyright 2015. All Rights Reserved. All trademarks and trade names are the properties of their respective owners. Chapter 1 Introduction This Chapter provides details of the Waterproof HD iP Camera's features. components and capabilities. The HD IP Camera has an Integrated Microcomputer and a high quality Mega Pixel Omni Vision CMOS Sensor, enabling it to display high quality live streaming video over your wired LAN, the Internet, and for the Waterproof HD IP Camera, an 802.11N Wireless LAN. Using enhanced H.264 technologies, the Waterproof HD IP Camera is able to stream high quality video and audio directly to your PC. The high compression capabilities of H.264 reduce network bandwidth requirements to amazingly low levels. This weather-resistant camera, which with the IP66 rated housing and internal heater, let you keep an eye on your belongings - even in harsh environments. It is also an all-in-one camera that has automatic and manual day/night switching, PIR sensor and built-in infrared LEDs, which can provide illumination around 6 meters long under low light conditions in a simple, economical manner. iP Camera Giiereel coteroy J \
a \ /
r - S Cabienst i, -
Figure 1: Network Diagram Waterproof HD IP Camera Features Standalone Design. The Waterproof HD IP Camera is a standalone system with built-in CPU and Video encoder. It requires only a power source and a connection to your LAN or Wireless LAN. Dual Video Support. The Waterproof HD IP Camera can support H.264 and MJEPG video for different image compression. Suitable for Home, Business or Public Facilities. Whether for Home, Business or Public Facility surveillance, or just for entertainment and fun, the Waterproof HD IP Camera has the features you need. Day/Night Switch: With the day/night switching feature, you are able to view and record better images even in the dark of night. IR LED Support. Each Waterproof HD IP Camera has one infrared LED. The LED can provide illumination around 6 meters long, that can help to output a better video quality while under low-light conditions such as on cloudy days, or in the morning or evening. PIR (Passive Infrared Sensor) Support. The Waterproof HD IP Camera is embedded with a PIR Sensor, which senses infrared light radiating from human bodies in its field of view. This feature is very helpful in enhancing home security systems. Built-in Heater. The built-in Heater can support the camera to be used in the extreme cold outdoor climate applications. The heater should be turn on when temperature is below 6 C. Wireless Features Supports 11n Wireless Stations. The 802.11n standard provides for backward compatibility with the 802.11b standard, so 802.11n, 802.11b and 802.11g Wireless stations can be used simultaneously. Wired and Wireless Network Support. The Waterproof HD IP Camera supports either wired or wireless transmission. WEP Support. Full WEP support (64/128 Bit) on the Wireless interface is provided. WPA/WPA2 Support. The WPA Personal/WPA2 Personal standard is also supported, allowing advanced encryption of wireless data. WPS Support. WPS (Wi-Fi Protected Setup) can simplify the process of connecting any device to the wireless network by using the push button configuration (PBC) on the Waterproof HD IP Camera, or entering a PIN code if there's no button. to Chapter 2 Basic Setup This Chapter provides details on how to install and configure the Waterproof HD iP Camera. System Requirements e Touse the Wireless interface on the wireless model, other Wireless devices must be compliant with the IEEE802.11b, IEEE802.11g, or
|EEE802.11n specifications. All Wireless stations must use compatible settings. Physical Details - Waterproof HD IP Camera Front Panel - Waterproof HD IP Camera Figure 2: Front Panel 4. Light Sensor This is hardware sensor to detect LUX. 2. Lens No physical adjustment is required or possible for the lens, but you should ensure that the lens cover remains clean. The image quality is degraded if the lens cover is dirty or smudged. 3. PIR Sensor This is hardware sensor to detect motion. Rear Panel - Waterproof HD IP Camera Figure 3: Rear Panel 1. DC Power Input Connect the supplied 12V/1.5A power adapter here. Do not use other power adapters; doing so may damage the camera. 2. WPS/Reset Button This button has two functions:
1. WPS. Push the WPS button on the device and on your other wireless device to perform WPS function that easily creates an encryption-secured wireless connection automatically. e WPS PBC Mode. When pressed and released (one second), the Waterproof HD IP Camera will be in the WPS PBC mode (Auto link mode). e WPS Pin Code Mode. When pressed and held for 3-10 seconds, the Waterproof HD IP Camera will be in the WPS Pin Code mode. 2. Reset to manufacturer default valued and reboot. When pressed and held over 10 seconds, the settings of Network Camera will be set to their default values. 3. Microphone The built-in microphone is useful for bi-
direction voice conversation. 4. Power LED
(Green, Amber) 5. Network/Wireless LED
(Green, Amber) 6. LAN port On (Green) - Power on. Off - No power. Blinking (Green) - The Power LED will blink during start up. This will take 55 to 57 seconds. On (Amber) - Firmware upgrade is failed. Blinking (Amber) - The firmware is upgrading. On (Green) - Network (Wireless or LAN) connection is available. Off - Wireless or LAN is not connected or camera is not sending/receiving data. Blinking (Green) - Data is being transmitted or received via the LAN or Wireless connection. On (Amber) - If the LED is on for 5 seconds and then off, the WPS function is failed. Blinking (Amber) - WPS function is being processed. Use a RJ-45 USB cable (Only for paring, not suitable for outdoor usage) to connect your camera to a 10/100BaseT hub or switch. Note:
e Plugging in the RJ-45 USB cable will disable the Wireless interface. Only 1 interface can be active at any time. e The RJ-45 USB cable should only be connected or disconnected when the camera is powered OFF. Attaching or detaching the RJ-45 USB cable while the camera is powered on does NOT switch the interface between wired and wireless. Set up of Waterproof HD iP Camera 1. Assemble the Camera Attach the Camera Stand to the camera. 2. Internet Connection Wire Connection Connect the Camera to a 10/100BaseT hub or switch, using a RJ-45 USB cable (Only for paring, not suitable for outdoor usage) and a standard LAN cable. KES For this Model, it will disable the Wireless Interface. The Wireless and LAN interfaces cannot be used Note! simultaneously. Using the LAN interface is recommended for initial configuration. After the Wireless settings are correct, the Wireless interface can be used. The first time you connect to the camera, you should connect the RJ-45 USB cable and configure the Wireless IP Gamera with appropriate settings. Then you can unplug the RJ-45 USB cable and power off the camera. The Wireless IP Camera will be in wireless interface when you power on the camera again. e Wireless Connection Press the WPS button on the camera for 3-5 seconds and on your other wireless device as well to establish a wireless connection automatically. The wireless connection is successful when the Network/WPS LED (green) remains on. 3. Power Up Connect the supplied 12V/1.5A power adapter to the Wireless IP Camera and power up. Use only the power adapter provided. Using a different one may cause hardware damage.
*Note: The operating temperature of power adapter is 0 C to 40 C. Please ensure the power adapter is indoor usage. 4. Check the LEDs eThe PowerLED will turn on briefly, then start blinking. It will blink during startup, which will take 55 to 57 seconds. After startup is completed, the Power LED should remain ON. e The Network/WPS LED should be ON.
* Optional: Mounting the Waterproof HD IP Camera
*Note: Please ensure camera is configured and added to the network before permanent mounting. 1. Identify the location for mounting the camera. 2. Align the two mounting holes at the bottom of the camera stand with the two screws, and mount the mounting plate onto the screws. 4. There are two methods for Internet connection:
e Connect a USB to RJ-45 cable (Only for paring, not suitable for outdoor usage) to the USB port of the Wireless IP Camera. Then use a standard LAN cable to connect an available port on your router. e Press the WPS button on the Wireless IP Camera for 3-5 seconds and on your other wireless device as well to establish a wireless connection automatically. The wireless connection is successful when the Network/WPS LED (green) is on. 8 5. Connect the power cable into the back of the camera and then insert the rubber cap. Caution: Make sure the rubber cap is attached seamlessly and well-positioned to the camera so the water will not get into the camera. ef A aS o> _ -
6. Plug the adapter end into a power outlet. 7. Adjust the Wireless IP Camera to a desired position and secure it firmly. Appendix A Specifications Waterproof HD [P Camera Model Waterproof HD IP Camera Dimensions 76.4mm (W) x 76.4mm (H) x 32.8mm (D}
Operating -20 C to 50 C (Cold Start: -40C/ heater mode: -40C to Temperature 0c) Video compression H.264 and MJPEG Image resolution Storage Temperature Network Protocols Network Interface Wireless interface Button LEDs IR LED Power Adapter 16:9 720p (1280*720), 640*360 4:3 XGA (1024*720), VGA (640*480), QVGA (320*240) Mixed Mode (720p, VGA, QVGA)
-40 C to 70 C TCP/IP, HTTP, HTTPS, DHCP, UPnP, NTP, , RTCP, DNS 4 RJ-45 USB connector for Ethernet (Only for paring, not suitable for outdoor usage}
IEEE 802.11n/802.11b/802.11g compatible, WEP 64/128 bit, WPA/WPA2 personal security support
+ WPS/Network Button 2 2 12V/1.5A, 100~240V Regulatory Approvals FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
10 e Reorient or relocate the receiving antenna. e Increase the separation between the equipment and receiver. e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. e Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. CE Approval CE Standards This product complies with the 99/5/EEC directives, including the following safety and EMC standards:
eEN55 022/24 CE Marking Warning This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. ll
1 | Internal Photos | Internal Photos | 1.37 MiB | July 21 2015 |
Compliance Certification Services Inc. Report No.: T150508D06 INTERNAL PHOTOGRAPHS OF EUT A1 - 5 / 10 Rev. 00 Compliance Certification Services Inc. Report No.: T150508D06 A1 - 6 / 10 Rev. 00 Compliance Certification Services Inc. Report No.: T150508D06 A1 - 7 / 10 Rev. 00 Compliance Certification Services Inc. Report No.: T150508D06 A1 - 8 / 10 Rev. 00 Compliance Certification Services Inc. Report No.: T150508D06 A1 - 9 / 10 Rev. 00 Compliance Certification Services Inc. Report No.: T150508D06 RF IC A1 - 10 / 10 Rev. 00 Antenna
1 | External Photos | External Photos | 581.86 KiB | July 21 2015 |
Compliance Certification Services Inc. Report No.: T150508D06 APPENDIX 1 - PHOTOGRAPHS OF EUT EXTERNAL PHOTOGRAPHS OF EUT A1 - 1 / 10 Rev. 00 Compliance Certification Services Inc. Report No.: T150508D06 A1 - 2 / 10 Rev. 00 Compliance Certification Services Inc. Report No.: T150508D06 A1 - 3 / 10 Rev. 00 Compliance Certification Services Inc. Report No.: T150508D06 A1 - 4 / 10 Rev. 00
1 | Agents Letter | Cover Letter(s) | 46.84 KiB | July 21 2015 |
BABT TCB DateJuly 16, 2015 FCC ID: P27OC830 Dear Sir or Madam, We, Sercomm Corporation hereby authorize Compliance Certification Services Inc / Miller.Lee . to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. This authorization expires on 2016/1/3 Your Sincerely, Kevin Kuo Sr. Manager / R&D Division Sercomm Corporation TEL: 886-2-2655-3988#2631 FAX: 886-2-2655-7379 E-Mail: kevin_kuo@sercomm.com
1 | Confidentiality Letter | Cover Letter(s) | 59.14 KiB | July 21 2015 |
BABT TCB DateJuly 3, 2015 Confidentiality Request FCC ID: P27OC830 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules, Sercomm Corporation hereby requests permanent confidential treatment of information accompanying this application as outlined below:
Common exhibits for which confidentiality is requested are:
Schematics Block Diagrams Theory of Operation The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Your Sincerely, Kevin Kuo Sr. Manager / R&D Division Sercomm Corporation TEL: 886-2-2655-3988#2631 FAX: 886-2-2655-7379 E-Mail: kevin_kuo@sercomm.com
1 | DoC Letter | Cover Letter(s) | 51.20 KiB | July 21 2015 |
DateJuly 3, 2015 Subject:DoC declaration To Whom it may concern, We, as the grantee of this project FCC ID: P27OC830, would like to declare that the composite Portion categorized as computer peripheral has been authorized under the Declaration of Conformity procedures. Brand Name & Model Name of the specified radio equipment:
Sercomm / OC830xxxxxxxx (the 1st x should be "blank" or "-"; the rest x could be 0 to 9, A to Z, "blank" or - , for marking purpose) FCC ID: P27OC830 Product Name: HD IP Camera Regards, Your Sincerely, Kevin Kuo Sr. Manager / R&D Division Sercomm Corporation TEL: 886-2-2655-3988#2631 FAX: 886-2-2655-7379 E-Mail: kevin_kuo@sercomm.com
1 | RF Exposure Report | RF Exposure Info | 157.54 KiB |
Compliance Certification Services Inc. Report No.: T150508D06-MF KDB 447498 D03 IEEE C95.1 47 C.F.R. Part 1, Subpart I, Section 1.1310 47 C.F.R. Part 2, Subpart J, Section 2.1091 RF EXPOSURE REPORT For HD IP Camera Model: OC830xxxxxxxx (the 1st x should be "blank" or "-"; the rest x could be 0 to 9, A to Z, "blank" or - , for marking purpose) Trade Name: Sercomm Issued to 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. Sercomm Corporation Issued by Compliance Certification Services Inc. No.11, Wugong 6th Rd., Wugu Dist., New Taipei City 24891, Taiwan. (R.O.C.) http://www.ccsrf.com service@ccsrf.com Issued Date: June 11, 2015 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 1 Rev.00 Compliance Certification Services Inc. Report No.: T150508D06-MF Revision History Rev. Issue Date Revisions Effect Page Revised By 00 2015/06/11 Initial Issue ALL Becca Chen This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 2 Rev.00 Compliance Certification Services Inc. Report No.: T150508D06-MF TABLE OF CONTENTS 1. LIMIT .................................................................................................................... 4 2. EUT SPECIFICATION .......................................................................................... 4 3. TEST RESULTS................................................................................................... 5 4. MAXIMUM PERMISSIBLE EXPOSURE .............................................................. 6 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 3 Rev.00 Compliance Certification Services Inc. Report No.: T150508D06-MF 1. LIMIT According to 15.247(i), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See 1.1307(b)(1) of this chapter. 2. EUT SPECIFICATION EUT Model HD IP Camera OC830xxxxxxxx (the 1st x should be "blank" or "-"; the rest x could be 0 to 9, A to Z, "blank" or - , for marking purpose) RF Module REALTEK Model:
RTL8192EU Model Discrepancy Frequency band
(Operating) Device category Exposure classification Antenna Specification Maximum Average output power Maximum Tune up Power All the above models are identical except for the designation of model numbers. The suffix of "X" (the 1st x should be "blank" or "-"; the rest x could be 0 to 9, A to Z, "blank" or - , for marking purpose) on model number is just for marketing purpose only. 802.11b/g/n HT20: 2.412GHz ~ 2.462GHz 802.11 n HT40: 2.422GHz ~ 2.452GHz Others Portable (<20cm separation) Mobile (>20cm separation) Others Occupational/Controlled exposure (S = 5mW/cm2) General Population/Uncontrolled exposure
(S=1mW/cm2) PIFA Antenna Evaluation applied MPE Evaluation*
SAR Evaluation N/A This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 4 Rev.00 2.4GHz: Right Antenna Gain :2.52 dBi(Numeric gain:1.79)wost Lift Antenna Gain :2.16 dBi(Numeric gain:1.64)IEEE 802.11b Mode:18.31 dBm(67.764 mW)IEEE 802.11g Mode:16.34 dBm(43.053 mW)IEEE 802.11n HT 20 Mode: 18.24 dBm(66.681 mW)IEEE 802.11n HT 40 Mode: 18.26 dBm(66.988 mW)IEEE 802.11b Mode:19.00 dBm(79.433 mW)IEEE 802.11g Mode:19.00 dBm(79.433 mW)IEEE 802.11n HT 20 Mode: 19.00 dBm(79.433 mW)IEEE 802.11n HT 40 Mode: 19.00 dBm(79.433 mW) Compliance Certification Services Inc. Report No.: T150508D06-MF 3. TEST RESULTS No non-compliance noted. Calculation Given
&
Where E = Field strength in Volts / meter P = Power in Watts G = Numeric antenna gain d = Distance in meters S = Power density in milliwatts / square centimeter Combining equations and re-arranging the terms to express the distance as a function of the remaining variables yields:
Changing to units of mW and cm, using:
Yields P (mW) = P (W) / 1000 and d (cm) = d(m) / 100 Equation 1 Where d = Distance in cm P = Power in mW G = Numeric antenna gain S = Power density in mW / cm2 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 5 Rev.00 dGPE303772ES237730dGPS220796.0100/3771000/30dGPdGPS Compliance Certification Services Inc. Report No.: T150508D06-MF 4. MAXIMUM PERMISSIBLE EXPOSURE Substituting the MPE safe distance using d = 20 cm into Equation 1:
Where P = Power in mW G = Numeric antenna gain S = Power density in mW / cm2 IEEE 802.11b mode:
IEEE 802.11g mode:
IEEE 802.11n HT20 mode:
IEEE 802.11n HT40 mode:
This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 6 Rev.00 GPS000199.0Ch.Frq.(MHz)P (mW)Gain (num.)D (cm)Power density in mW / cm2Limit (mW/cm2)6243779.4331.79200.02831Ch.Frq.(MHz)P (mW)Gain (num.)D (cm)Power density in mW / cm2Limit (mW/cm2)11246279.4331.79200.02831Ch.Frq.(MHz)P (mW)Gain (num.)D (cm)Power density in mW / cm2Limit (mW/cm2)6243779.4331.79200.02831Ch.Frq.(MHz)P (mW)Gain (num.)D (cm)Power density in mW / cm2Limit (mW/cm2)9245279.4331.79200.02831
1 | Test Report | Test Report | 4.81 MiB | July 21 2015 |
Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP FCC 47 CFR PART 15 SUBPART C TEST REPORT For HD IP Camera Model:
OC830xxxxxxxx (the 1st x should be "blank" or "-"; the rest x could be 0 to 9, A to Z, "blank" or - , for marking purpose) Trade Name: Sercomm Issued to Sercomm Corporation 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. Issued by Compliance Certification Services Inc. No.11, Wugong 6th Rd., Wugu Dist., New Taipei City 24891, Taiwan. (R.O.C.) http://www.ccsrf.com service@ccsrf.com Issued Date: June 5, 2015 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 / 129 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Revision History Rev. 00 Issue Date June 5, 2015 Initial Issue Revisions Effect Page Revised By ALL Becca Chen Page 2 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION .................................................................................................... 4 2. EUT DESCRIPTION ........................................................................................................................... 5 3. TEST METHODOLOGY .................................................................................................................... 6 3.1 EUT CONFIGURATION ................................................................................................................. 6 3.2 EUT EXERCISE ............................................................................................................................... 6 3.3 GENERAL TEST PROCEDURES .................................................................................................. 6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS .................................................... 7 3.5 DESCRIPTION OF TEST MODES ................................................................................................. 8 4. INSTRUMENT CALIBRATION ........................................................................................................ 9 4.1 MEASURING INSTRUMENT CALIBRATION ............................................................................ 9 4.2 MEASUREMENT EQUIPMENT USED ......................................................................................... 9 4.3 MEASUREMENT UNCERTAINTY ............................................................................................. 10 5. FACILITIES AND ACCREDITATIONS ........................................................................................ 11 5.1 FACILITIES ................................................................................................................................... 11 5.2 EQUIPMENT ................................................................................................................................. 11 5.3 TABLE OF ACCREDITATIONS AND LISTINGS ...................................................................... 12 6. SETUP OF EQUIPMENT UNDER TEST ....................................................................................... 13 6.1 SETUP CONFIGURATION OF EUT ............................................................................................ 13 6.2 SUPPORT EQUIPMENT ............................................................................................................... 13 7. FCC PART 15.247 REQUIREMENTS ............................................................................................. 14 7.1 6DB BANDWIDTH ....................................................................................................................... 14 7.2 PEAK POWER ............................................................................................................................... 34 7.3 AVERAGE POWER ...................................................................................................................... 36 7.4 BAND EDGES MEASUREMENT ................................................................................................ 38 7.5 PEAK POWER SPECTRAL DENSITY ........................................................................................ 68 7.6 SPURIOUS EMISSIONS ............................................................................................................... 88 7.7 RADIATED EMISSIONS ............................................................................................................ 107 7.8 POWERLINE CONDUCTED EMISSIONS ................................................................................ 124 APPENDIX I PHOTOGRAPHS OF TEST SETUP ............................................................................. 127 APPENDIX 1 - PHOTOGRAPHS OF EUT Page 3 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 1. TEST RESULT CERTIFICATION Applicant:
Sercomm Corporation 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. Equipment Under Test:
HD IP Camera Trade Name:
Sercomm Model Number:
OC830xxxxxxxx (the 1st x should be "blank" or "-"; the rest x could be 0 to 9, A to Z, "blank" or - , for marking purpose) Date of Test:
May 28 ~ June 3, 2015 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that:
The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10: 2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.247. The test results of this report relate only to the tested sample EUT identified in this report. Approved by:
Reviewed by:
Miller Lee Manager Compliance Certification Services Inc. Angel Cheng Section Manager Compliance Certification Services Inc. Page 4 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 2. EUT DESCRIPTION Product HD IP Camera Trade Name Sercomm Model Number OC830xxxxxxxx (the 1st x should be "blank" or "-"; the rest x could be 0 to 9, A to Z, "blank" or - , for marking purpose) Received Date May 8, 2015 Power Adapter Frequency Range Transmit Power Asian Power Devices Inc. Model: WA-18D12FU I/P: 100-240V, 50-60Hz, 0.5A MAX O/P: 12V, 1.5A 2412 ~ 2462 MHz Mode 802.11b 802.11g Frequency Range Output Power Output Power 2412 - 2462 2412 - 2462 2412 - 2462 2422 - 2452
(dBm) 20.64 25.62 27.67 27.32
(W) 0.1159 0.3648 0.5848 0.5395 802.11n Standard-20 MHz 802.11n Standard-40 MHz IEEE 802.11b mode: DSSS (1, 2, 5.5 and 11 Mpbs) IEEE 802.11g mode: OFDM (6, 9, 12, 18, 24, 36, 48 and 54 Mpbs) IEEE 802.11n HT 20 MHz mode Channel mode: OFDM (6.5, 7.2, 13, Modulation Technique 14.4, 14.44, 19.5, 21.7, 26, 28.89, 28.9, 39, 43.3, 43.33 52, 57.78, 57.8, 58.5, 65.0, 72.2, 78, 86.67, 104, 115.56, 117, 130, 144.44 Mbps) IEEE 802.11n HT 40 MHz mode: OFDM (13.5, 15, 27, 30, 40.5, 45, 54, 60, 81, 90, 108, 120, 121.5, 135, 150, 162, 180, 216, 240, 243, 270, 300 Mbps) Number of Channels IEEE 802.11b/g mode: 11 Channels IEEE 802.11n HT 20 MHz mode: 11 Channels IEEE 802.11n HT 40 MHz mode: 7 Channels Antenna Specification PIFA Antenna / 2.52dBi Remark:
1. The sample selected for test was engineering sample that approximated to production product and was provided by manufacturer. 2. This submittal(s) (test report) is intended for FCC ID: P27OC830 filing to comply with Section 15.207, 15.209 and 15.247 of the FCC Part 15, Subpart C Rules. Page 5 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.10: 2009 and FCC CFR 47 Part 15.207, 15.209, 15.247 and KDB558074. 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.207, 15.209 and 15.247 under the FCC Rules Part 15 Subpart C. 3.3 GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.10: 2009 Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 1.5 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 13.1.4.1 of ANSI C63.10:
2009. Page 6 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS
(a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below:
MHz MHz MHz GHz 0.090 - 0.110 10.495 - 0.505 2.1735 - 2.1905 4.125 - 4.128 4.17725 - 4.17775 4.20725 - 4.20775 6.215 - 6.218 6.26775 - 6.26825 6.31175 - 6.31225 8.291 - 8.294 8.362 - 8.366 8.37625 - 8.38675 8.41425 - 8.41475 16.42 - 16.423 16.69475 - 16.69525 16.80425 - 16.80475 25.5 - 25.67 37.5 - 38.25 73 - 74.6 74.8 - 75.2 108 - 121.94 123 - 138 149.9 - 150.05 156.52475 -
156.52525 156.7 - 156.9 12.29 - 12.293 162.0125 - 167.17 12.51975 - 12.52025 12.57675 - 12.57725 13.36 - 13.41 167.72 - 173.2 240 - 285 322 - 335.4 399.9 - 410 608 - 614 960 - 1240 1300 - 1427 1435 - 1626.5 1645.5 - 1646.5 1660 - 1710 1718.8 - 1722.2 2200 - 2300 2310 - 2390 2483.5 - 2500 2655 - 2900 3260 - 3267 3332 - 3339 3345.8 - 3358 3600 - 4400 4.5 - 5.15 5.35 - 5.46 7.25 - 7.75 8.025 - 8.5 9.0 - 9.2 9.3 - 9.5 10.6 - 12.7 13.25 - 13.4 14.47 - 14.5 15.35 - 16.2 17.7 - 21.4 22.01 - 23.12 23.6 - 24.0 31.2 - 31.8 36.43 - 36.5
(2) 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6
(b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. Page 7 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 3.5 DESCRIPTION OF TEST MODES The EUT (model: OC835-ADT) had been tested under operating condition. Software used to control the EUT for staying in continuous transmitting mode was programmed. After verification, all tests were carried out with the worst case test modes as shown below except radiated spurious emission below 1GHz and power line conducted emissions below 30MHz, which worst case was in normal link mode only. The EUT is a 2x2 configuration spatial MIMO (2Tx & 2Rx) without beam forming function that operate in double TX chains and double RX chains. The 2x2 configuration is implemented with two outside TX & RX chains (Chain 0 and 1). IEEE 802.11b mode:
Channel Low (2412MHz), Channel Mid (2437MHz) and Channel High (2462MHz) with 1Mbps data rate were chosen for full testing. IEEE 802.11g mode:
Channel Low (2412MHz), Channel Mid (2437MHz) and Channel High (2462MHz) with 6Mbps data rate were chosen for full testing. IEEE 802.11n HT 20 MHz mode:
Channel Low (2412MHz), Channel Mid (2437MHz) and Channel High (2462MHz) with 6.5Mbps data rate were chosen for full testing. IEEE 802.11n HT 40 MHz mode:
Channel Low (2422MHz), Channel Mid (2437MHz) and Channel High (2452MHz) with 13.5Mbps data rate were chosen for full testing. The field strength of spurious emission was measured in the following position: EUT stand-up position (Z axis), lie-down position (X, Y axis) and laptop mode. The worst emission was found in stand-up position (Z axis) and the worst case was recorded. Page 8 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 4. INSTRUMENT CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement Remark: Each piece of equipment is scheduled for calibration once a year and Loop Antenna is scheduled for calibration once three years. Conducted Emissions Test Site Name of Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent E4446A US42510252 11/23/2015 Thermostatic/Hrgrosatic Chamber TAICHY MHG-150LF 930619 10/07/2015 AC Power Source EXTECH DC Power Supply Power Meter Power Sensor ABM Anritsu Anritsu 6205 8301HD ML2495A MA2411A Spectrum Analyzer ROHDE&SCHWARZ FSV40 1140845 D011531 1012009 0917072 101073 N.C.R N.C.R 06/03/2015 06/03/2015 07/09/2015 Wugu 966 Chamber A Name of Equipment Manufacturer Spectrum Analyzer EMI Test Receiver Agilent R&S Bilog Antenna Sunol Sciences Horn Antenna EMCO Turn Table Antenna Tower Controller Test S/W CCS CCS CCS Model E4446A ESCI JB3 3117 CC-T-1F CC-A-1F CC-C-1F Serial Number Calibration Due US42510268 100064 A030105 00055165 N/A N/A N/A 01/25/2016 05/30/2015 08/19/2015 01/26/2016 N.C.R N.C.R N.C.R EZ-EMC (CCS-3A1RE) Conducted Emission room # A Name of Equipment Manufacturer TEST RECEIVER R&S Model ESCI LISN (EUT) SCHWARZBECK NSLK 8127 LISN SCHWARZBECK NSLK 8127 Serial Number Calibration Due 101201 8127527 8127526 BNC#A7 08/31/2015 08/28/2015 08/28/2015 04/08/2016 BNC CABLE Pulse Limiter THERMO-
HYGRO METER Test S/W EMCI R&S CFD300-NL ESH3-Z2 C3010026-2 08/26/2015 WISEWIND 201A No. 02 05/10/2016 EZ-EMC Page 9 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 4.3 MEASUREMENT UNCERTAINTY PARAMETER UNCERTAINTY Powerline Conducted Emission 3M Semi Anechoic Chamber / 30M~200M 3M Semi Anechoic Chamber / 200M~1000M 3M Semi Anechoic Chamber / 1G~8G 3M Semi Anechoic Chamber / 8G~18G 3M Semi Anechoic Chamber / 18G~26G 3M Semi Anechoic Chamber / 26G~40G
+/- 1.59
+/- 4.0138
+/- 3.9483
+/- 2.5975
+/- 2.6112
+/- 2.7389
+/- 2.9683 Remark: This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Page 10 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at No.139, Wugong Rd., Wugu Dist., New Taipei City 24891, Taiwan (R.O.C.) Tel: 886-2-2298-4086 / Fax: 886-2-2298-1470 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City 24891, Taiwan. (R.O.C.) Tel: 886-2-2299-9720 / Fax: 886-2-2298-4045 No.81-1, Lane 210, Bade 2nd Rd., Lujhu Township, Taoyuan County 33841, TAIWAN, R.O.C. Tel: 886-3-324-0332 / Fax: 886-3-324-5235 No.163-1, Jhongsheng Rd. Sindian City, Taipei County 23151, Taiwan. Tel: 886-2-2217-0894 / Fax: 886-2-2217-1029 The powerline conducted emissions test items was tested at Compliance Certification Services Inc. (Sindian Lab.) The test equipments were listed in page 9 and the test data, please refer page 125-126. The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.10:
2009 and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, Radio Interference Measuring Apparatus and Measurement Methods. Page 11 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 5.3 TABLE OF ACCREDITATIONS AND LISTINGS Country Agency Scope of Accreditation Logo USA FCC 3M Semi Anechoic Chamber (FCC MRA: TW1039) to perform FCC Part 15 measurements Taiwan TAF LP0002, RTTE01, FCC Method-47 CFR Part 15 Subpart C, D, E, RSS-210, RSS-310 IDA TS SRD, AS/NZS 4268, AS/NZS 4771, TS 12.1 & 12,2, ETSI EN 300 440-1, ETSI EN 300 440-2, ETSI EN 300 328, ETSI EN 300 220-1, ETSI EN 300 220-2, ETSI EN 301 893, ETSI EN 301 489-1/3/7/17 FCC OET Bulletin 65 + Supplement C, EN 50360, EN 50361, EN 50371, RSS 102, EN 50383, EN 50385, EN 50392, IEC 62209, CNS 14958-1, CNS 14959 FCC Method 47 CFR Part 15 Subpart B IEC / EN 61000-3-2, IEC / EN 61000-3-3, IEC / EN 61000-4-2/3/4/5/6/8/11 FCC MRA: TW1039 Canada Industry Canada 3M Semi Anechoic Chamber (IC 2324G-1 / IC 2324G-2) to perform IC 2324G-1 IC 2324G-2
* No part of this report may be used to claim or imply product endorsement by A2LA or any agency of the US Government. Page 12 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix II for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT No Equipment Brand Model Series No. FCC ID Data Cable Power Cord 1 Notebook PC
(For Radiation) Server Notebook IBM 7663 (T61) L3E9812 N/A N/A AC I/P:
Unshielded, 1.8m DC O/P:
Unshielded, 1.8m with a core DOC BSMI: R33002 Unshielded, 20m Unshielded, 1.8m 2.
(Remote) DELL E5420 6YRVLQ1
(For Conduction) Remark:
1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturers requirements and conditions for the intended use. Page 13 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 7. FCC PART 15.247 REQUIREMENTS 7.1 6DB BANDWIDTH LIMIT According to 15.247(a)(2), systems using digital modulation techniques may operate in the 902 -
928 MHz, 2400 - 2483.5 MHz, and 5725 - 5850 MHz bands. The minimum 6dB bandwidth shall be at least 500 kHz. Test Configuration EUT Spectrum Analyzer TEST PROCEDURE 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the spectrum analyzer as RBW = 300 kHz, VBW = 1000 kHz, Sweep = auto. 4. Mark the peak frequency and 6dB (upper and lower) frequency. 5. Repeat until all the rest channels are investigated. TEST RESULTS No non-compliance noted. Page 14 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Test Data Test mode: IEEE 802.11b mode Frequency Channel Test mode: IEEE 802.11g mode Frequency Channel Low Mid High Low Mid High
(MHz) 2412 2437 2462
(MHz) 2412 2437 2462 Bandwidth
(MHz) 10.3334 10.3334 10.3334 Bandwidth
(MHz) 16.8333 16.8333 16.8333 Test mode: IEEE 802.11n HT 20 MHz mode / Chain 0 Channel Low Mid High Frequency
(MHz) 2412 2437 2462 Bandwidth
(MHz) 17.8334 17.8334 17.8334 Test mode: IEEE 802.11n HT 20 MHz mode / Chain 1 Channel Low Mid High Frequency
(MHz) 2412 2437 2462 Bandwidth
(MHz) 17.8334 17.8334 17.8334 Test mode: IEEE 802.11n HT 40 MHz mode / Chain 0 Channel Low Mid High Frequency
(MHz) 2422 2437 2452 Bandwidth
(MHz) 36.4167 36.4167 36.4167 Test mode: IEEE 802.11n HT 40 MHz mode / Chain 1 Channel Low Mid High Frequency
(MHz) 2422 2437 2452 Bandwidth
(MHz) 36.4166 36.5 36.5 Limit
(kHz)
>500 Limit
(kHz)
>500 Limit
(kHz)
>500 Limit
(kHz)
>500 Limit
(kHz)
>500 Limit
(kHz)
>500 Result PASS PASS PASS Result PASS PASS PASS Result PASS PASS PASS Result PASS PASS PASS Result PASS PASS PASS Result PASS PASS PASS Page 15 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Test Plot IEEE 802.11b mode 6dB Bandwidth (CH Low) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2406.8333 2412.5000 2417.1667 2.24 9.38 1.57 3.38 3.38 3.38
-1.14 6.00
-1.81 No. 1 mk3-mk1 Frequency(MHz) Level(dB) 10.3334
-0.67 Page 16 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6dB Bandwidth (CH Mid) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2431.8333 2437.5000 2442.1667 2.79 9.77 1.88 3.77 3.77 3.77
-0.98 6.00
-1.89 mk3-mk1 Frequency(MHz) Level(dB) 10.3334
-0.91 No. 1 Page 17 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6dB Bandwidth (CH High) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2456.8333 2461.5000 2467.1667 2.94 9.75 1.84 3.75 3.75 3.75
-0.81 6.00
-1.91 mk3-mk1 Frequency(MHz) Level(dB) 10.3334
-1.1 No. 1 Page 18 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11g mode 6dB Bandwidth (CH Low) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2403.5000 2416.1667 2420.3333
-0.36 6.44
-0.86 0.44 0.44 0.44
-0.80 6.00
-1.30 mk3-mk1 Frequency(MHz) Level(dB) 16.8333
-0.5 No. 1 Page 19 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6dB Bandwidth (CH Mid) No. 1 No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2428.5000 2441.1667 2445.3333 0.69 7.29
-0.03 1.29 1.29 1.29
-0.60 6.00
-1.32 mk3-mk1 Frequency(MHz) Level(dB) 16.8333
-0.72 Page 20 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6dB Bandwidth (CH High) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2453.5000 2454.2500 2470.3333 0.89 7.38
-0.26 1.38 1.38 1.38
-0.49 6.00
-1.64 mk3-mk1 Frequency(MHz) Level(dB) 16.8333
-1.15 No. 1 Page 21 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11n HT 20 MHz mode / Chain 0 6dB Bandwidth (CH Low) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2403.0833 2407.0833 2420.9167
-0.86 5.24
-2.19
-0.76
-0.76
-0.76
-0.10 6.00
-1.43 mk3-mk1 Frequency(MHz) Level(dB) 17.8334
-1.33 No. 1 Page 22 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6dB Bandwidth (CH Mid) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2428.0833 2432.0833 2445.9167
-0.94 5.18
-2.30
-0.82
-0.82
-0.82
-0.12 6.00
-1.48 No. 1 mk3-mk1 Frequency(MHz) Level(dB) 17.8334
-1.36 Page 23 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6dB Bandwidth (CH High) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2453.0833 2457.0833 2470.9167
-0.97 5.13
-2.73
-0.87
-0.87
-0.87
-0.10 6.00
-1.86 mk3-mk1 Frequency(MHz) Level(dB) 17.8334
-1.76 No. 1 Page 24 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11n HT 20 MHz mode / Chain 1 6dB Bandwidth (CH Low) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2403.0833 2407.0833 2420.9167
-2.13 4.24
-2.78
-1.76
-1.76
-1.76
-0.37 6.00
-1.02 mk3-mk1 Frequency(MHz) Level(dB) 17.8334
-0.65 No. 1 Page 25 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6dB Bandwidth (CH Mid) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2428.0833 2432.0833 2445.9167
-2.01 4.38
-2.90
-1.62
-1.62
-1.62
-0.39 6.00
-1.28 mk3-mk1 Frequency(MHz) Level(dB) 17.8334
-0.89 No. 1 Page 26 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6dB Bandwidth (CH High) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2453.0833 2457.0833 2470.9167
-2.91 3.39
-3.95
-2.61
-2.61
-2.61
-0.30 6.00
-1.34 mk3-mk1 Frequency(MHz) Level(dB) 17.8334
-1.04 No. 1 Page 27 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11n HT 40 MHz mode / Chain 0 6dB Bandwidth (CH Low) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2403.8333 2419.8333 2440.2500
-2.07 4.51
-1.85
-1.49
-1.49
-1.49
-0.58 6.00
-0.36 mk3-mk1 Frequency(MHz) Level(dB) 36.4167 0.22 No. 1 Page 28 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6dB Bandwidth (CH Mid) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2418.8333 2434.8333 2455.2500
-1.95 4.45
-1.96
-1.55
-1.55
-1.55
-0.40 6.00
-0.41 No. 1 mk3-mk1 Frequency(MHz) Level(dB) 36.4167
-0.01 Page 29 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6dB Bandwidth (CH High) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2433.8333 2449.8333 2470.2500
-0.89 5.35
-1.29
-0.65
-0.65
-0.65
-0.24 6.00
-0.64 mk3-mk1 Frequency(MHz) Level(dB) 36.4167
-0.4 No. 1 Page 30 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11n HT 40 MHz mode / Chain 1 6dB Bandwidth (CH Low) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2403.9167 2428.6667 2440.3333
-2.18 3.85
-3.08
-2.15
-2.15
-2.15
-0.03 6.00
-0.93 mk3-mk1 Frequency(MHz) Level(dB) 36.4166
-0.9 No. 1 Page 31 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6dB Bandwidth (CH Mid) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2418.8333 2434.9167 2455.3333
-3.67 2.74
-4.19
-3.26
-3.26
-3.26
-0.41 6.00
-0.93 mk3-mk1 Frequency(MHz) Level(dB) 36.5
-0.52 No. 1 Page 32 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 6dB Bandwidth (CH High) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 3 2433.8333 2449.9167 2470.3333
-3.69 2.78
-4.05
-3.22
-3.22
-3.22
-0.47 6.00
-0.83 mk3-mk1 Frequency(MHz) Level(dB) 36.5
-0.36 No. 1 Page 33 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 7.2 PEAK POWER LIMIT The maximum peak output power of the intentional radiator shall not exceed the following:
1. According to 15.247(b)(3), for systems using digital modulation in the bands of 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz: 1 Watt. 2. According to 15.247(b)(4), the conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section, if transmitting antennas of directional gain greater than 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs (b)(1), (b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the antenna exceeds 6 dBi. Test Configuration EUT TEST PROCEDURE Power Meter Power Sensor The transmitter output is connected to the Power Meter. The Power Meter is set to the peak power detection. Page 34 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Test Data Test mode: IEEE 802.11b mode Frequency Output Power Output Power Channel Low Mid High Channel Low Mid High
(MHz) 2412 2437 2462
(dBm) 20.64 20.43 20.20
(MHz) 2412 2437 2462
(dBm) 25.62 25.51 25.60 Limit
(W)
(W) 0.1159 0.1104 1.00 0.1047 Limit
(W)
(W) 0.3648 0.3556 1.00 0.3631 Result PASS PASS PASS Result PASS PASS PASS Test mode: IEEE 802.11g mode Frequency Output Power Output Power Test mode: IEEE 802.11n HT 20 MHz mode Channel Frequency
(MHz) Low Mid High 2412 2437 2462 Chain 0 Chain 1 Output Power Output Power
(dBm) 24.92 25.12 24.68
(dBm) 24.07 24.14 24.08 Total Output Power Output Power
(dBm)
(W) Limit
(W) 27.53 27.67 27.40 0.5662 0.5848 1.00 0.5495 Test mode: IEEE 802.11n HT 40 MHz mode Channel Frequency
(MHz) Low Mid High 2422 2437 2452 Remark:
Chain 0 Chain 1 Output Power Output Power
(dBm) 24.31 24.51 24.35
(dBm) 24.11 24.09 24.22 Total Output Power Output Power
(dBm)
(W) Limit
(W) 27.22 27.32 27.30 0.5272 0.5395 1.00 0.5370 1. Total Output Power (w) = Chain 0 (10^(Output Power /10)/1000)+ Chain 1 (10^(Output Power /10)/1000) Result PASS PASS PASS Result PASS PASS PASS Page 35 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 7.3 AVERAGE POWER LIMIT None; for reporting purposes only. Test Configuration EUT TEST PROCEDURE Power Meter Power Sensor The transmitter output is connected to the Power Meter. The Power Meter is set to the avg power detection. TEST RESULTS No non-compliance noted. Page 36 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Test Data Test mode: IEEE 802.11b mode Channel Low Mid High Frequency Output Power Output Power
(MHz) 2412 2437 2462
(dBm) 18.23 18.31 18.01
(W) 0.0665 0.0678 0.0632 Test mode: IEEE 802.11g mode Channel Low Mid High Frequency Output Power Output Power
(MHz) 2412 2437 2462
(dBm) 16.24 16.11 16.34
(W) 0.0421 0.0408 0.0431 Test mode: IEEE 802.11n HT 20 MHz mode Channel Frequency
(MHz) Low Mid High 2412 2437 2462 Chain 0 Chain 1 Output Power Output Power
(dBm) 15.02 15.25 15.13
(dBm) 15.03 15.21 15.28 Total Output Power Output Power
(dBm) 18.04 18.24 18.22
(W) 0.0637 0.0667 0.0664 Test mode: IEEE 802.11n HT 40 MHz mode Channel Frequency
(MHz) Low Mid High 2422 2437 2452 Chain 0 Chain 1 Output Power Output Power
(dBm) 15.12 15.38 15.28
(dBm) 15.01 15.1 15.21 Total Output Power Output Power
(dBm) 18.08 18.25 18.26
(W) 0.0643 0.0668 0.0670 Remark: Total Output Power (w) = Chain 0 (10^(Output Power /10)/1000)+ Chain 1 (10^(Output Power /10)/1000) Page 37 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 7.4 BAND EDGES MEASUREMENT LIMIT According to 15.247(d), in any 100 kHz bandwidth outside the frequency bands in which the spread spectrum intentional radiator in operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. In addition, radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see Section 15.205(c)). Test Configuration For Radiated For Conducted EUT Spectrum Analyzer Page 38 Rev. 00 Spectrum analyzer Horn antenna 3m 4m 1m Turntable EUT 0.8m Antenna tower Pre-amp Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP TEST PROCEDURE For Radiated 1. The EUT is placed on a turntable, which is 1.5m above the ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emission. 4. Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission:
(a) PEAK: RBW=VBW=3MHz / Sweep=AUTO
(b) AVERAGE: RBW=1MHz, if duty cycle98%, VBW=10Hz. if duty cycle<98% VBW=1/T. IEEE 802.11b mode: 98%, VBW=10Hz IEEE 802.11g mode: 98%, VBW=10Hz IEEE 802.11n HT 20 MHz mode: 98%, VBW=10Hz IEEE 802.11n HT 40 MHz mode: 98%, VBW=10Hz 5. Repeat the procedures until all the PEAK and AVERAGE versus POLARIZATION are measured. For Conducted Conducted RF measurements of the transmitter output were made to confirm that the EUT antenna port conducted emissions meet the specified limit and to identify any spurious signals that require further investigation or measurements on the radiated emissions site. The transmitter output is connected to the spectrum analyzer. The resolution bandwidth is set to 100 kHz. The video bandwidth is set to 100 kHz. TEST RESULTS Refer to attach spectrum analyzer data chart. Page 39 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Band Edges (IEEE 802.11b mode / CH Low) Polarity: Vertical No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2386.720 53.15 2386.720 39.68
-3.80
-3.80 49.35 74.00
-24.65 100 35.88 54.00
-18.12 100 83 83 peak AVG Page 40 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Polarity: Horizontal No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2384.480 56.09 2384.480 43.37
-3.82
-3.82 52.27 74.00
-21.73 100 39.55 54.00
-14.45 100 72 72 peak AVG Page 41 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Band Edges (IEEE 802.11b mode / CH High) Polarity: Vertical No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm) 2497.640 58.70 2497.640 42.82
-3.14
-3.14 55.56 39.68 74.00
-18.44 54.00
-14.32 100 100
( ) 263 263 peak AVG Page 42 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Polarity: Horizontal No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2388.720 58.12 2388.720 43.36
-3.78
-3.78 54.34 74.00
-19.66 100 39.58 54.00
-14.42 100 347 347 peak AVG Page 43 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Band Edges (IEEE 802.11g mode / CH Low) Polarity: Vertical No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2388.720 58.12 2388.720 43.36
-3.78
-3.78 54.34 74.00
-19.66 100 39.58 54.00
-14.42 100 347 347 peak AVG Page 44 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Polarity: Horizontal No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2388.000 61.58 2388.000 46.67
-3.79
-3.79 57.79 74.00
-16.21 100 42.88 54.00
-11.12 100 23 23 peak AVG Page 45 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Band Edges (IEEE 802.11g mode / CH High) Polarity: Vertical No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2497.558 64.09 2497.558 42.95
-3.14
-3.14 60.95 74.00
-13.05 100 39.81 54.00
-14.19 100 133 133 peak AVG Page 46 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Polarity: Horizontal No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2483.962 69.32 2483.962 52.23
-3.27
-3.27 66.05 74.00
-7.95 48.96 54.00
-5.04 100 100 185 185 peak AVG Page 47 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Band Edges (IEEE 802.11n HT 20 MHz mode / CH Low) Polarity: Vertical No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2389.840 61.79 2389.840 44.84
-3.77
-3.77 58.02 74.00
-15.98 100 41.07 54.00
-12.93 100 325 325 peak AVG Page 48 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Polarity: Horizontal No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm) 2390.000 62.92 2390.000 47.51
-3.77
-3.77 59.15 43.74 74.00
-14.85 54.00
-10.26 100 100
( ) 273 273 peak AVG Page 49 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Band Edges (IEEE 802.11n HT 20 MHz mode / CH High) Polarity: Vertical No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2483.847 58.82 2483.847 43.77
-3.27
-3.27 55.55 74.00
-18.45 100 40.50 54.00
-13.50 100 295 295 peak AVG Page 50 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Polarity: Horizontal No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2483.533 68.87 2483.533 50.32
-3.27
-3.27 65.60 74.00
-8.40 47.05 54.00
-6.95 100 100 214 214 peak AVG Page 51 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Band Edges (IEEE 802.11n HT 40 MHz mode / CH Low) Polarity: Vertical No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2380.320 60.29 2380.320 47.01
-3.86
-3.86 56.43 74.00
-17.57 100 43.15 54.00
-10.85 100 138 138 peak AVG Page 52 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Polarity: Horizontal No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2379.760 64.57 2379.760 51.36
-3.86
-3.86 60.71 74.00
-13.29 100 47.50 54.00
-6.50 100 333 333 peak AVG Page 53 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Band Edges (IEEE 802.11n HT 40 MHz mode / CH High) Polarity: Vertical No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2483.929 61.37 2483.929 46.60
-3.27
-3.27 58.10 74.00
-15.90 100 43.33 54.00
-10.67 100 210 210 peak AVG Page 54 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Polarity: Horizontal No. Frequency Reading Correct Result Limit Margin Height Degree Remark 1 2
(MHz)
(dBuV) Factor(dB/m)
(dBuV/m)
(dBuV/m)
(dB)
(cm)
( ) 2484.077 68.65 2484.077 52.18
-3.27
-3.27 65.38 74.00
-8.62 48.91 54.00
-5.09 100 100 255 255 peak AVG Page 55 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Test Plot Conducted Band Edges (IEEE 802.11b mode / CH Low) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2399.5000 2412.5000
-29.81 7.75
-12.25
-12.25
-17.56 20.00 Page 56 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Conducted Band Edges (IEEE 802.11b mode / CH High) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2461.5000 2488.0000 8.12
-48.65
-11.88
-11.88 20.00
-36.77 Page 57 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Conducted Band Edges (IEEE 802.11g mode / CH Low) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2400.0000 2416.1250
-31.94 0.99
-19.01
-19.01
-12.93 20.00 Page 58 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Conducted Band Edges (IEEE 802.11g mode / CH High) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2454.2500 2484.2500 2.00
-45.48
-18.00
-18.00 20.00
-27.48 Page 59 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Conducted Band Edges (IEEE 802.11n HT 20 MHz mode / CH Low / chain 0) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2400.0000 2409.1250
-32.09 0.34
-19.66
-19.66
-12.43 20.00 Page 60 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Conducted Band Edges (IEEE 802.11n HT 20 MHz mode / CH High / chain 0) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2459.1250 2483.8750 0.24
-46.24
-19.76
-19.76 20.00
-26.48 Page 61 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Conducted Band Edges (IEEE 802.11n HT 20 MHz mode / CH Low / chain 1) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2399.8750 2409.1250
-33.85
-0.60
-20.60
-20.60
-13.25 20.00 Page 62 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Conducted Band Edges (IEEE 802.11n HT 20 MHz mode / CH High / chain 1) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2459.1250 2483.8750
-1.51
-48.63
-21.51
-21.51 20.00
-27.12 Page 63 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Conducted Band Edges (IEEE 802.11n HT 40 MHz mode / CH Low / chain 0) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2400.0000 2414.2500
-34.51
-3.28
-23.28
-23.28
-11.23 20.00 Page 64 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Conducted Band Edges (IEEE 802.11n HT 40 MHz mode / CH High / chain 0 ) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2455.5000 2484.5000
-2.46
-41.27
-22.46
-22.46 20.00
-18.81 Page 65 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Conducted Band Edges (IEEE 802.11n HT 40 MHz mode / CH Low / chain 1) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2400.0000 2414.2500
-34.81
-4.18
-24.18
-24.18
-10.63 20.00 Page 66 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Conducted Band Edges (IEEE 802.11n HT 40 MHz mode / CH High / chain 1 ) No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2455.5000 2485.1250
-5.02
-45.43
-25.02
-25.02 20.00
-20.41 Page 67 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 7.5 PEAK POWER SPECTRAL DENSITY LIMIT 1. According to 15.247(e), for digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. 2. According to 15.247(f), the digital modulation operation of the hybrid system, with the frequency hopping turned off, shall comply with the power density requirements of paragraph (d) of this section. Test Configuration EUT Spectrum Analyzer TEST PROCEDURE 1. Place the EUT on the table and set it in transmitting mode. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 2. Set the spectrum analyzer as RBW=10kHz,VBW=100kHz,Span=1.5 times the DTS bandwidth, Sweep time= auto 3. Record the max reading. 4. Repeat the above procedure until the measurements for all frequencies are completed. TEST RESULTS No non-compliance noted. Page 68 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Test Data Test mode: IEEE 802.11b mode Channel Low Mid High Frequency
(MHz) 2412 2437 2462 PPSD
(dBm)
-1.97
-1.62
-1.63 Test mode: IEEE 802.11g mode Channel Low Mid High Frequency
(MHz) 2412 2437 2462 PPSD
(dBm)
-6.53
-5.70
-5.62 Limit
(dBm) 8.00 Limit
(dBm) 8.00 Result PASS PASS PASS Result PASS PASS PASS Test mode: IEEE 802.11n HT 20 MHz mode Channel Frequency
(MHz) Chain 0 PPSD
(dBm) Chain 1 PPSD
(dBm) Low Mid High 2412 2437 2462
-6.55
-6.59
-6.70
-7.34
-7.38
-8.30 Limit
(dBm) PPSD
(dBm)
-3.92
-3.96 8.00
-4.42 nTest mode: IEEE 802.11n HT 40 MHz mode Channel Frequency
(MHz) Low Mid High Remark:
2422 2437 2452 Chain 0 PPSD
(dBm)
-9.24
-9.26
-8.12 Chain 1 PPSD
(dBm)
-9.79
-11.79
-11.63 Limit
(dBm) PPSD
(dBm)
-6.50
-7.33 8.00
-6.52 1. Total PPSD (dBm) = 10*LOG(10^(Chain 0 PPSD / 10)+10^(Chain 1 PPSD /10)) Result PASS PASS PASS Result PASS PASS PASS Page 69 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Test Plot IEEE 802.11b mode PPSD (CH Low) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2412.6500
-1.97 8.00
-9.97 Page 70 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP PPSD (CH Mid) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2437.6500
-1.62 8.00
-9.62 Page 71 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP PPSD (CH High) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2462.6500
-1.63 8.00
-9.63 Page 72 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11g mode PPSD (CH Low) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2419.8000
-6.53 8.00
-14.53 Page 73 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP PPSD (CH Mid) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2439.1667
-5.70 8.00
-13.70 Page 74 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP PPSD (CH High) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2456.0333
-5.62 8.00
-13.62 Page 75 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11n HT 20 MHz mode / Chain 0 PPSD (CH Low) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2418.5000
-6.55 8.00
-14.55 Page 76 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP PPSD (CH Mid) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2434.8667
-6.59 8.00
-14.59 Page 77 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP PPSD (CH High) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2459.8667
-6.70 8.00
-14.70 Page 78 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11n HT 20 MHz mode / Chain 1 PPSD (CH Low) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2418.5000
-7.34 8.00
-15.34 Page 79 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP PPSD (CH Mid) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2434.8667
-7.38 8.00
-15.38 Page 80 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP PPSD (CH High) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2455.3667
-8.30 8.00
-16.30 Page 81 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11n HT 40 MHz mode / Chain 0 PPSD (CH Low) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2414.1333
-9.24 8.00
-17.24 Page 82 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP PPSD (CH Mid) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2429.1333
-9.26 8.00
-17.26 Page 83 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP PPSD (CH High) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2455.3333
-8.12 8.00
-16.12 Page 84 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11n HT 40 MHz mode / Chain 1 PPSD (CH Low) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2425.3333
-9.79 8.00
-17.79 Page 85 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP PPSD (CH Mid) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2444.8667
-11.79 8.00
-19.79 Page 86 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP PPSD (CH High) No. 1 Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 2435.3333
-11.63 8.00
-19.63 Page 87 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 7.6 SPURIOUS EMISSIONS 7.6.1 Conducted Measurement LIMIT According to 15.247(d), in any 100 kHz bandwidth outside the frequency bands in which the spread spectrum intentional radiator in operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. In addition, radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see Section 15.205(c)). Test Configuration EUT Spectrum Analyzer TEST PROCEDURE Conducted RF measurements of the transmitter output were made to confirm that the EUT antenna port conducted emissions meet the specified limit and to identify any spurious signals that require further investigation or measurements on the radiated emissions site. The transmitter output is connected to the spectrum analyzer. The resolution bandwidth is set to 100 kHz. The video bandwidth is set to 100 kHz. Measurements are made over the 30MHz to 25GHz range with the transmitter set to the lowest, middle, and highest channels. TEST RESULTS No non-compliance noted. Page 88 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Test Plot IEEE 802.11b mode CH Low No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 4824.2400
-48.74
-42.89
-11.84
-11.84
-36.90
-31.05 Page 89 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP CH Mid No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2327.2400 4874.1800
-54.54
-43.19
-11.46
-11.46
-43.08
-31.73 Page 90 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP CH High No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 4924.1200
-55.59
-41.98
-11.46
-11.46
-44.13
-30.52 Page 91 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11g mode CH Low No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 24925.0900
-46.74
-48.67
-18.72
-18.72
-28.02
-29.95 Page 92 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP CH Mid No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 24950.0600
-55.74
-48.65
-17.75
-17.75
-37.99
-30.90 Page 93 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP CH High No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 24425.6900
-55.87
-48.41
-17.63
-17.63
-38.24
-30.78 Page 94 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11n HT 20 MHz mode / Chain 0 CH Low No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 24975.0300
-45.77
-48.46
-19.46
-19.46
-26.31
-29.00 Page 95 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP CH Mid No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2352.2100 23576.7100
-55.78
-48.56
-19.75
-19.75
-36.03
-28.81 Page 96 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP CH High No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 24900.1200
-56.98
-49.05
-19.51
-19.51
-37.47
-29.54 Page 97 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11n HT 20 MHz mode / Chain 1 CH Low No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 24200.9600
-48.22
-48.18
-20.64
-20.64
-27.58
-27.54 Page 98 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP CH Mid No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 23526.7700
-57.29
-48.95
-20.36
-20.36
-36.93
-28.59 Page 99 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP CH High No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2352.2100 24400.7200
-58.09
-48.36
-21.22
-21.22
-36.87
-27.14 Page 100 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11n HT 40 MHz mode / Chain 0 CH Low No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 23476.8300
-45.25
-48.61
-22.80
-22.80
-22.45
-25.81 Page 101 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP CH Mid No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 24425.6900
-51.98
-48.26
-22.83
-22.83
-29.15
-25.43 Page 102 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP CH High No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 30.0000 2502.0300
-53.31
-45.82
-21.95
-21.95
-31.36
-23.87 Page 103 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP IEEE 802.11n HT 40 MHz mode / Chain 1 CH Low No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 24425.6900
-44.57
-48.34
-23.55
-23.55
-21.02
-24.79 Page 104 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP CH Mid No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 2377.1800 23501.8000
-53.08
-48.70
-24.70
-24.70
-28.38
-24.00 Page 105 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP CH High No. Frequency(MHz) Result(dBm) Limit(dBm) Margin(dBm) 1 2 30.0000 24975.0300
-56.76
-48.61
-24.65
-24.65
-32.11
-23.96 Page 106 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 7.7 RADIATED EMISSIONS LIMIT 1. According to 15.209(a), except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table:
Frequency Field Strength Measurement Distance
(MHz) 30-88 88-216 216-960 Above 960
(V/m) 100*
150*
200*
500
(m) 3 3 3 3 Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 2. In the emission table above, the tighter limit applies at the band edges. Frequency Field Strength Field Strength
(MHz) 30-88 88-216 216-960 Above 960
(V/m at 3-meter)
(dBV/m at 3-meter) 100 150 200 500 40 43.5 46 54 Page 107 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Test Configuration 9kHz ~ 30MHz 30MHz ~ 1GHz Page 108 Rev. 00 Spectrum / Receiver 3m 1m Turntable EUT 0.8m Loop antenna Reference ground plane Spectrum analyzer 3m 4m 1m Turntable EUT 0.8m Antenna tower Reference ground plane Bi-log antenna Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Above 1 GHz Page 109 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP TEST PROCEDURE 1. The EUT is placed on a turntable, which is 1.5m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as:
Below 1GHz:
RBW=100kHz / VBW=300kHz / Sweep=AUTO Above 1GHz:
(a) PEAK: RBW=VBW=10MHz / Sweep=AUTO
(b) AVERAGE: RBW=10Hz, if duty cycle98%, VBW=1Hz. if duty cycle<98% VBW=1/T. IEEE 802.11b mode: 98%, VBW=10Hz IEEE 802.11g mode: 98%, VBW=10Hz IEEE 802.11n HT 20 MHz mode: 98%, VBW=10Hz IEEE 802.11n HT 40 MHz mode: 98%, VBW=10Hz 7. Repeat above procedures until the measurements for all frequencies are complete. TEST RESULTS No non-compliance noted. Page 110 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Below 1GHz Operation Mode: Normal Link Test Date:
May 28, 2015 Temperature:
27C Humidity:
53% RH Tested by:
David Shu Polarity:
Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 250.1900 450.0100 570.2900 798.2400 888.4500 960.2300 206.5400 275.4100 431.5800 570.2900 792.4200 849.6500 Remark:
50.68 47.20 46.14 41.61 34.45 37.71 47.87 52.03 42.14 45.70 41.36 39.66 Correction Factor
(dB/m)
-16.27
-10.19
-8.19
-4.51
-3.33
-2.23
-16.01
-14.70
-10.75
-8.19
-4.56
-3.79 Result Limit
(dBuV/m)
(dBuV/m) 34.41 37.01 37.95 37.10 31.12 35.48 31.86 37.33 31.39 37.51 36.80 35.87 46.00 46.00 46.00 46.00 46.00 54.00 43.50 46.00 46.00 46.00 46.00 46.00 Margin
(dB)
-11.59
-8.99
-8.05
-8.90
-14.88
-18.52
-11.64
-8.67
-14.61
-8.49
-9.20
-10.13 Remark Ant. Pol.
(H/V) Peak Peak Peak Peak Peak Peak peak peak peak peak peak peak V V V V V V H H H H H H 1. Measuring frequencies from 30 MHz to the 1GHz. 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using peak/quasi-peak detector mode. 3. Quasi-peak test would be performed if the peak result were greater than the quasi-peak limit or as required by the applicant. 4. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 5. Margin (dB) = Result (dBuV/m) Limit (dBuV/m). Page 111 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Above 1 GHz Operation Mode: TX / IEEE 802.11b / CH Low Test Date: May 28, 2015 Temperature:
27C Humidity:
53 % RH Tested by: David Shu Polarity:
Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 1966.000 4105.000 N/A 1920.000 3900.000 4105.000 N/A Remark:
49.89 45.08 51.95 46.61 45.67 Correction Factor
(dB/m)
-5.06 1.63 Result Limit
(dBuV/m)
(dBuV/m) 44.83 46.71 74.00 74.00 Margin
(dB)
-29.17
-27.29
-5.30 0.80 1.63 46.65 47.41 47.30 74.00 74.00 74.00
-27.35
-26.59
-26.70 Remark Ant. Pol.
(H/V) peak peak peak peak peak V V H H H 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) Average limit (dBuV/m). Page 112 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Operation Mode: TX / IEEE 802.11b / CH Mid Test Date: May 28, 2015 Temperature:
27C Humidity:
53 % RH Tested by: David Shu Polarity: Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 2150.000 4985.000 N/A 1920.000 4105.000 N/A Remark:
Remark Ant. Pol.
(H/V) Correction Factor
(dB/m)
-4.71 3.95 Result Limit
(dBuV/m)
(dBuV/m) 46.49 50.68 74.00 74.00 Margin
(dB)
-27.51
-23.32 51.20 46.73 peak peak 53.26 46.42
-5.30 1.63 47.96 48.05 74.00 74.00
-26.04
-25.95 peak peak V V H H 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) Average limit (dBuV/m). Page 113 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Operation Mode: TX / IEEE 802.11b / CH High Test Date: May 28, 2015 Temperature:
27C Humidity:
53 % RH Tested by: David Shu Polarity: Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 1824.000 4500.000 N/A 1554.000 4105.000 N/A Remark:
Remark Ant. Pol.
(H/V) Correction Factor
(dB/m)
-5.81 3.12 Result Limit
(dBuV/m)
(dBuV/m) 46.72 48.16 74.00 74.00 Margin
(dB)
-27.28
-25.84 52.53 45.04 peak peak 55.55 48.29
-7.24 1.63 48.31 49.92 74.00 74.00
-25.69
-24.08 peak peak V V H H 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) Average limit (dBuV/m). Page 114 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Operation Mode: TX / IEEE 802.11g / CH Low Test Date: May 28, 2015 Temperature:
27C Humidity:
53 % RH Tested by: David Shu Polarity: Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 1554.000 3900.000 N/A 1554.000 4105.000 N/A Remark:
Remark Ant. Pol.
(H/V) Correction Factor
(dB/m)
-7.24 0.80 Result Limit
(dBuV/m)
(dBuV/m) 45.85 46.69 74.00 74.00 Margin
(dB)
-28.15
-27.31 53.09 45.89 peak peak 53.96 42.85
-7.24 1.63 46.72 44.48 74.00 74.00
-27.28
-29.52 peak peak V V H H 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) Average limit (dBuV/m). Page 115 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Operation Mode: TX / IEEE 802.11g / CH Mid Test Date: May 28, 2015 Temperature:
27C Humidity:
53 % RH Tested by: David Shu Polarity: Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 1554.000 4500.000 N/A 1554.000 3900.000 N/A Remark:
Remark Ant. Pol.
(H/V) Correction Factor
(dB/m)
-7.24 3.12 Result Limit
(dBuV/m)
(dBuV/m) 44.50 47.02 74.00 74.00 Margin
(dB)
-29.50
-26.98 51.74 43.90 peak peak 55.03 47.12
-7.24 0.80 47.79 47.92 74.00 74.00
-26.21
-26.08 peak peak V V H H 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) Average limit (dBuV/m). Page 116 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Operation Mode: TX / IEEE 802.11g / CH High Test Date: May 28, 2015 Temperature:
27C Humidity:
53 % RH Tested by: David Shu Polarity: Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 1172.000 4105.000 N/A 1800.000 4105.000 N/A Remark:
Remark Ant. Pol.
(H/V) Correction Factor
(dB/m)
-8.97 1.63 Result Limit
(dBuV/m)
(dBuV/m) 46.82 45.49 74.00 74.00 Margin
(dB)
-27.18
-28.51 55.79 43.86 peak peak 53.32 46.23
-5.94 1.63 47.38 47.86 74.00 74.00
-26.62
-26.14 peak peak V V H H 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) Average limit (dBuV/m). Page 117 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Operation Mode: TX / IEEE 802.11n HT 20 MHz mode / CH Low Test Date: May 28, 2015 Temperature:
27C Humidity:
53 % RH Tested by: David Shu Polarity: Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 1574.000 5215.000 N/A 2094.000 4105.000 N/A Remark:
Remark Ant. Pol.
(H/V) Correction Factor
(dB/m)
-7.14 4.54 Result Limit
(dBuV/m)
(dBuV/m) 47.48 46.09 74.00 74.00 Margin
(dB)
-26.52
-27.91 54.62 41.55 peak peak 52.27 45.45
-4.97 1.63 47.30 47.08 74.00 74.00
-26.70
-26.92 peak peak V V H H 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) Average limit (dBuV/m). Page 118 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Operation Mode: TX / IEEE 802.11n HT 20 MHz mode / CH Mid Test Date: May 28, 2015 Temperature:
27C Humidity:
53 % RH Tested by: David Shu Polarity: Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 1580.000 4200.000 N/A 1766.000 4105.000 N/A Remark:
Remark Ant. Pol.
(H/V) Correction Factor
(dB/m)
-7.11 1.99 Result Limit
(dBuV/m)
(dBuV/m) 46.99 47.66 74.00 74.00 Margin
(dB)
-27.01
-26.34 54.10 45.67 peak peak 53.49 47.48
-6.12 1.63 47.37 49.11 74.00 74.00
-26.63
-24.89 peak peak V V H H 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) Average limit (dBuV/m). Page 119 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Operation Mode: TX / IEEE 802.11n HT 20 MHz mode / CH High Test Date: May 28, 2015 Temperature:
27C Humidity:
53 % RH Tested by: David Shu Polarity: Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 1562.000 3900.000 N/A 2094.000 4105.000 N/A Remark:
Remark Ant. Pol.
(H/V) Correction Factor
(dB/m)
-7.20 0.80 Result Limit
(dBuV/m)
(dBuV/m) 47.30 48.31 74.00 74.00 Margin
(dB)
-26.70
-25.69 54.50 47.51 peak peak 52.98 45.95
-4.97 1.63 48.01 47.58 74.00 74.00
-25.99
-26.42 peak peak V V H H 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) Average limit (dBuV/m). Page 120 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Operation Mode: TX / IEEE 802.11n HT 40 MHz mode / CH Low Test Date: May 28, 2015 Temperature:
27C Humidity:
53 % RH Tested by: David Shu Polarity: Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 1938.000 4105.000 N/A 1554.000 4105.000 N/A Remark:
Remark Ant. Pol.
(H/V) Correction Factor
(dB/m)
-5.21 1.63 Result Limit
(dBuV/m)
(dBuV/m) 50.57 46.11 74.00 74.00 Margin
(dB)
-23.43
-27.89 55.78 44.48 peak peak 53.58 47.55
-7.24 1.63 46.34 49.18 74.00 74.00
-27.66
-24.82 peak peak V V H H 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) Average limit (dBuV/m). Page 121 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Operation Mode: TX / IEEE 802.11n HT 40 MHz mode / CH Mid Test Date: May 28, 2015 Temperature:
27C Humidity:
53 % RH Tested by: David Shu Polarity: Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 1938.000 4105.000 N/A 1554.000 4105.000 N/A Remark:
Remark Ant. Pol.
(H/V) Correction Factor
(dB/m)
-5.21 1.63 Result Limit
(dBuV/m)
(dBuV/m) 49.42 45.82 74.00 74.00 Margin
(dB)
-24.58
-28.18 54.63 44.19 peak peak 54.26 47.61
-7.24 1.63 47.02 49.24 74.00 74.00
-26.98
-24.76 peak peak V V H H 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) Average limit (dBuV/m). Page 122 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Operation Mode: TX / IEEE 802.11n HT 40 MHz mode / CH High Test Date: May 28, 2015 Temperature:
27C Humidity:
53 % RH Tested by: David Shu Polarity: Ver. / Hor. Frequency
(MHz) Reading
(dBuV) 1942.000 4105.000 N/A 1554.000 4105.000 N/A Remark:
Remark Ant. Pol.
(H/V) Correction Factor
(dB/m)
-5.19 1.63 Result Limit
(dBuV/m)
(dBuV/m) 48.06 46.76 74.00 74.00 Margin
(dB)
-25.94
-27.24 53.25 45.13 peak peak 53.89 47.71
-7.24 1.63 46.65 49.34 74.00 74.00
-27.35
-24.66 peak peak V V H H 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) Average limit (dBuV/m). Page 123 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP 7.8 POWERLINE CONDUCTED EMISSIONS LIMIT According to 15.207(a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 H/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Frequency Range
(MHz) 0.15 to 0.50 0.50 to 5 5 to 30 Limits
(dBV) Quasi-peak 66 to 56*
56 60 Average 56 to 46*
46 50
* Decreases with the logarithm of the frequency. Test Configuration See test photographs attached in Appendix II for the actual connections between EUT and support equipment. TEST PROCEDURE 1. The EUT was placed on a table, which is 0.8m above ground plane. 2. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 3. Repeat above procedures until all frequency measured were complete. Page 124 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP TEST RESULTS The initial step in collecting conducted data is a spectrum analyzer peak scan of the measurement range. Significant peaks are then marked as shown on the following data page, and these signals are then quasi-peaked. Test Data Operation Mode:
Normal Link Temperature:
25C Test Date:
Tested by:
June 3, 2015 Alee Shen Humidity:
58% RH Freq
(MHz) 0.2860 0.2980 2.7420 4.4859 13.3579 16.2299 0.1660 0.2860 0.5940 2.8500 13.3580 16.2300 Remark:
Reading
(dBuV) Corr. factor
(dB/m) Result
(dBuV/m) Limit
(dBuV) 38.99 36.02 24.70 26.04 30.53 30.64 33.62 38.20 24.68 25.30 30.81 30.80 10.01 10.01 10.30 10.37 10.70 10.80 10.01 10.01 10.07 10.32 10.70 10.80 49.00 46.03 35.00 36.41 41.23 41.44 43.63 48.21 34.75 35.62 41.51 41.60 60.64 60.30 56.00 56.00 60.00 60.00 65.16 60.64 56.00 56.00 60.00 60.00 Margin
(dB)
-11.64
-14.27
-21.00
-19.59
-18.77
-18.56
-21.53
-12.43
-21.25
-20.38
-18.49
-18.40 Note L1 L1 L1 L1 L1 L1 L2 L2 L2 L2 L2 L2 1. Measuring frequencies from 0.15 MHz to 30MHz. 2. The emissions measured in frequency range from 0.15 MHz to 30MHz were made with an instrument using Quasi-peak detector and average detector. 3. The IF bandwidth of SPA between 0.15MHz and 30MHz was 10 kHz; the IF bandwidth of Test Receiver between 0.15MHz and 30MHz was 9 kHz;
4. L1 = Line One (Live Line) / L2 = Line Two (Neutral Line) Page 125 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Test Plots Conducted emissions (Line 1) Conducted emissions (Line 2) Page 126 Rev. 00
1 | Test Setup Photos | Test Setup Photos | 410.83 KiB | July 21 2015 |
Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP APPENDIX I PHOTOGRAPHS OF TEST SETUP Conducted Emissions Setup Photos Page 127 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Radiated Emissions Setup Photos Page 128 Rev. 00 Compliance Certification Services Inc. FCC : P27OC830 Report No.: T150508D06-RP Powerline Conducted Emissions Setup Photos Page 129 Rev. 00
1 | Tune Up | Parts List/Tune Up Info | 21.12 KiB | July 21 2015 |
Snap-on Diagnostics Tune up procedure The output power setting of EUT is set in the factory and followed the max level in below. There is no tune up procedure except factory default setting:
17 dBm 2dB Kevin Kuo Sr. Manager / R&D Division Sercomm Corporation TEL: 886-2-2655-3988#2631 FAX: 886-2-2655-7379 E-Mail: kevin_kuo@sercomm.com
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2015-07-21 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2015-07-21
|
||||
1 | Applicant's complete, legal business name |
Sercomm Corporation
|
||||
1 | FCC Registration Number (FRN) |
0015548027
|
||||
1 | Physical Address |
8F, No. 3-1, YuanQu St, NanKang
|
||||
1 |
Taipei, N/A
|
|||||
1 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
V******@tuvam.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
P27
|
||||
1 | Equipment Product Code |
OC830
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
N**** W****
|
||||
1 | Title |
Engineer
|
||||
1 | Telephone Number |
886-2******** Extension:
|
||||
1 | Fax Number |
886-2********
|
||||
1 |
N******@SERCOMM.COM
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | HD IP Camera | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power is conducted. This device has 20 and 40 MHz BW modes. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. End users must be informed of the requirements for satisfying RF Exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Compliance Certification Services Inc.
|
||||
1 | Name |
H******** L****
|
||||
1 | Telephone Number |
886-2******** Extension:
|
||||
1 | Fax Number |
886-2********
|
||||
1 |
h******@sgs.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2412.00000000 | 2462.00000000 | 0.5848000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC