| all | frequencies |
|
|
|
|
exhibits | applications |
|---|---|---|---|---|---|---|---|
| manual | photos | label | |||||
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
User Manual | Users Manual | 244.55 KiB | September 23 2014 | |||
| 1 |
|
Internal Photos | Internal Photos | 454.57 KiB | September 23 2014 | |||
| 1 |
|
External Photos | External Photos | 101.99 KiB | September 23 2014 | |||
| 1 |
|
Label | ID Label/Location Info | 2.42 MiB | September 23 2014 | |||
| 1 |
|
Agents Letter | Cover Letter(s) | 50.80 KiB | September 23 2014 | |||
| 1 | Antenna Details | Operational Description | September 23 2014 | confidential | ||||
| 1 | Antenna Details II | Operational Description | September 23 2014 | confidential | ||||
| 1 | Block Diagram | Block Diagram | September 23 2014 | confidential | ||||
| 1 |
|
Confidentiality Letter | Cover Letter(s) | 51.42 KiB | September 23 2014 | |||
| 1 |
|
DoC Letter | Cover Letter(s) | 50.85 KiB | September 23 2014 | |||
| 1 | Operating Description | Operational Description | September 23 2014 | confidential | ||||
| 1 |
|
RF Exposure Report | RF Exposure Info | 122.57 KiB | September 23 2014 | |||
| 1 | Schematics | Schematics | September 23 2014 | confidential | ||||
| 1 |
|
Test Report | Test Report | 1.03 MiB | September 23 2014 | |||
| 1 |
|
Test Setup Photos | Test Setup Photos | 285.36 KiB | September 23 2014 | |||
| 1 |
|
Tune Up | Parts List/Tune Up Info | 19.70 KiB | September 23 2014 |
| 1 | User Manual | Users Manual | 244.55 KiB | September 23 2014 |
SZ-DWS04 ZigBee Door/Window Sensor Installation Guide Specification 2.4GHz CR2032 Battery
> 3 cm ( 1.18 inch ) 0 C to 40 C (32 - 104F)
-20 C to 60 C (-4 - 140F) 3 years 40M Main Unit: 51 mm x 26 mm x 7.4 mm (2" x 1.02" x 0.29") Magnet Unit: 28.3 mm x 15.5 mm x 7.4 mm (1.11" x 0.61" x 0.29") Frequency Batter Type Sensitivity Operating Temperature Storage Temperature Battery Life RF Range Dimension Package Contents 1 Intallation NOTE: Please make sure that the sensor and magnet is located less then 1.27cm (0.5 inch) from each other. Intallation 1. Hold the sensor near the top of the door, close to the opening edge of the door. This is the mounting location for the sensor. 2. Pull the exposed plastic pull tab from the sensor 3. Use either one of the following methods to install the sensor:
Remove the back plate of the sensor; use this as the mounting bracket. Use the screwdriver to secure the back plate to the wall with the screws provided. Then place the hooks into the two holes of the cover and attach the cover to the plate. 2 Use provided adhesive on the sensor. Attach the sensor to the door. Press firmly and hold in place for a few seconds. Magnet Setup 1. Attach the magnet on the location next to the sensor by using either one of the following methods:
Remove the back plate of the magnet; use this as the mounting bracket. Use the screwdriver to secure the back plate to the wall with the screws provided. Use provided adhesive on the magnet. Attach the sensor to the door. Press firmly and hold in place for a few seconds. 2. Make sure the alignment marks of both devices are facing each other. 3 Operation The LED will stay off during the normal operation. The sensor is equipped with a tamper switch. If the cover of sensor is removed, the sensor will send an alarm to the ZigBee coordinator. The sensor will be in "Awake" mode before replacing the cover. Reset to Factory Defaults A security sensor should be able to be manually defaulted from the device by putting it into a state where it is ready to be paired to a CPE. The process shall be as follows:
Depress the tamper switch after removing the battery from the sensor. Insert the battery. The sensor should illuminate the LED once all bootup/initialization tasks are complete Release the tamper switch while the LED is illuminated (4 seconds) The sensor should then reset to default and begin searching for a new network 4 FCC Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Increase the separation between the equipment and receiver. Reorient or relocate the receiving antenna. Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC Approvals CAN-ICES-3 (B)/ NMB-3(B) This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body. Dclaration d'exposition aux radiations:Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. UL Approvals UL Notices: This device complies with UL Standard UL634.
| 1 | Internal Photos | Internal Photos | 454.57 KiB | September 23 2014 |
INTERNAL PHOTOGRAPHS OF EUT Report No: T140725D05 Page 2 Rev.00 Report No: T140725D05 Page 3 Rev.00 Report No: T140725D05 Antenna Page 4 Rev.00
| 1 | External Photos | External Photos | 101.99 KiB | September 23 2014 |
EXTERNAL PHOTOGRAPHS OF EUT Report No: T140725D05 Page 1 / 4 Rev.00
| 1 | Agents Letter | Cover Letter(s) | 50.80 KiB | September 23 2014 |
DateAugust 12, 2014 BABT TCB Forsyth House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD Dear Sir or Madam, We, Sercomm Corporation hereby authorize Compliance Certification Services Inc / James.Chan . to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. This authorization expires on 2015/1/28 Your Sincerely, Kevin Kuo Sr. Manager / R&D Division Sercomm Corporation TEL: 886-2-2655-3988#2631 FAX: 886-2-2655-7379 E-Mail: kevin_kuo@sercomm.com
| 1 | Confidentiality Letter | Cover Letter(s) | 51.42 KiB | September 23 2014 |
DateAugust 12, 2014 BABT TCB Forsyth House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD Confidentiality Request FCC ID: P27SZDWS04 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules, Sercomm Corporation hereby requests permanent confidential treatment of information accompanying this application as outlined below:
Common exhibits for which confidentiality is requested are:
Schematics Block Diagrams Theory of Operation The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Your Sincerely, Kevin Kuo Sr. Manager / R&D Division Sercomm Corporation TEL: 886-2-2655-3988#2631 FAX: 886-2-2655-7379 E-Mail: kevin_kuo@sercomm.com
| 1 | DoC Letter | Cover Letter(s) | 50.85 KiB | September 23 2014 |
DateAugust 12, 2014 Subject:DoC declaration To Whom it may concern, We, as the grantee of this project FCC ID: P27SZDWS04, would like to declare that the composite Portion categorized as computer peripheral has been authorized under the Declaration of Conformity procedures. Brand Name & Model Name of the specified radio equipment:
Comcast /SZ-DWS04 FCC ID: P27SZDWS04 Product Name: Micro Door Window Sensor Regards, Your Sincerely, Kevin Kuo Sr. Manager / R&D Division Sercomm Corporation TEL: 886-2-2655-3988#2631 FAX: 886-2-2655-7379 E-Mail: kevin_kuo@sercomm.com
| 1 | RF Exposure Report | RF Exposure Info | 122.57 KiB | September 23 2014 |
Compliance Certification Services Inc. Report No.: T140725D05 - MF Date of Issue: August 9, 2014 According to KDB 447498 section 4.3.1, the 1-g SAR test exclusion thresholds at test separation distance 50 mm are determined by:
[(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] *[f(GHz)] 3.0 The tune-up power is 6 dBm +/- 2dB, therefore the highest tune-up power is When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. So,
[(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] * [f(GHz)] = 1.6 < 3.0 Therefore, standalone SAR measurements are not required for both head and body. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 1 Rev.00 7.1 dBm(5.13 mW)@ 2405 MHz(5mW / 5mm)* (2405.000GHz^0.5 )= 50.3
| 1 | Test Report | Test Report | 1.03 MiB | September 23 2014 |
Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 FCC 47 CFR PART 15 SUBPART C TEST REPORT For Micro Door Window Sensor Model: SZ-DWS04 Trade Name: Comcast Issued to 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. Sercomm Corporation Issued by Compliance Certification Services Inc. No.81-1, Lane 210, Bade 2nd Rd., Lujhu Township, Taoyuan County 33841, Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 http://www.ccsrf.com service@ccsrf.com Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, A2LA, NIST or any government agencies. The test results in the report only apply to the tested sample. Page 1 / 46 Rev.00 Rev. 00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Issue Date August 5, 2014 Revision History Revisions Effect Page Revised By Initial Issue ALL Landy Huang This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 2 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ...........................................................................................4 2. EUT DESCRIPTION................................................................................................................5 3. TEST METHODOLOGY..........................................................................................................6 3.1 EUT CONFIGURATION.....................................................................................................6 3.2 EUT EXERCISE.................................................................................................................6 3.3 GENERAL TEST PROCEDURES......................................................................................6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ..........................................7 3.5 DESCRIPTION OF TEST MODES.....................................................................................8 4. INSTRUMENT CALIBRATION ...............................................................................................9 4.1 MEASURING INSTRUMENT CALIBRATION ....................................................................9 4.2 MEASUREMENT EQUIPMENT USED ..............................................................................9 4.3 MEASUREMENT UNCERTAINTY...................................................................................10 5. FACILITIES AND ACCREDITATIONS.................................................................................11 5.1 FACILTIES.......................................................................................................................11 5.2 EQUIPMENT....................................................................................................................11 5.3 TABLE OF ACCREDITATIONS AND LISTINGS..............................................................12 6. SETUP OF EQUIPMENT UNDER TEST ..............................................................................13 6.1 SETUP CONFIGURATION OF EUT ................................................................................13 6.2 SUPPORT EQUIPMENT..................................................................................................13 7. FCC PART 15.247 REQUIREMENTS ..................................................................................14 7.1 6DB BANDWIDTH ............................................................................................................14 7.2 PEAK POWER .................................................................................................................17 7.3 AVERAGE POWER .........................................................................................................18 7.4 BAND EDGES MEASUREMENT.....................................................................................19 7.5 PEAK POWER SPECTRAL DENSITY.............................................................................24 7.6 SPURIOUS EMISSIONS..................................................................................................27 7.7 POWERLINE CONDUCTED EMISSIONS.......................................................................40 8. APPENDIX I PHOTOGRAPHS OF TEST SETUP................................................................41 APPENDIX 1: PHOTOGRAPHS OF EUT...................................................................................44 APPENDIX 2: REMARKS ...........................................................................................................45 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 3 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 1. TEST RESULT CERTIFICATION Applicant:
Manufacturer:
Sercomm Corporation 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. Sercomm Corporation 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. Equipment Under Test: Micro Door Window Sensor Trade Name:
Model:
Date of Test:
Comcast SZ-DWS04 July 29 ~ 31, 2014 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that:
The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.247. The test results of this report relate only to the tested sample EUT identified in this report. Approved by:
Stan Lin Section Manager Reviewced by:
Angel Hu Section Manager This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 4 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 2. EUT DESCRIPTION Product Micro Door Window Sensor Trade Name Model Number Comcast SZ-DWS04 Model Discrepancy N/A EUT Power Rating 3VDC From Battery RF Module Manufacturer ARM Model EM3585 Operating Frequency Range 2405 ~ 2480MHz Transmit Power 11.17dBm (0.0131W) Modulation Technique OPQSK (Offset Quadrature Phase Shift Keyed) Number of Channels 16 Channels Antenna Specification Remark:
Chip Antenna / Gain: 1.76 dBi 1. The sample selected for test was production product and was provided by manufacturer. 2. This submittal(s) (test report) is intended for FCC ID: P27SZDWS04 filing to comply with Section 15.207, 15.209 and 15.247 of the FCC Part 15, Subpart C Rules. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 5 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4 and FCC CFR 47 Part 2, Part 15.207, 15.209 and 15.247. 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.207, 15.209 and 15.247 under the FCC Rules Part 15 Subpart C. 3.3 GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.4 Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 13.1.4.1 of ANSI C63.4. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 6 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS
(a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below:
MHz MHz 0.090 - 0.110 10.495 - 0.505 2.1735 - 2.1905 4.125 - 4.128 4.17725 - 4.17775 4.20725 - 4.20775 6.215 - 6.218 6.26775 - 6.26825 6.31175 - 6.31225 8.291 - 8.294 8.362 - 8.366 8.37625 - 8.38675 8.41425 - 8.41475 12.29 - 12.293 12.51975 - 12.52025 12.57675 - 12.57725 13.36 - 13.41 16.42 - 16.423 16.69475 - 16.69525 16.80425 - 16.80475 25.5 - 25.67 37.5 - 38.25 73 - 74.6 74.8 - 75.2 108 - 121.94 123 - 138 149.9 - 150.05 156.52475 -
156.52525 156.7 - 156.9 162.0125 - 167.17 167.72 - 173.2 240 - 285 322 - 335.4 MHz 399.9 - 410 608 - 614 960 - 1240 1300 - 1427 1435 - 1626.5 1645.5 - 1646.5 1660 - 1710 1718.8 - 1722.2 2200 - 2300 2310 - 2390 2483.5 - 2500 2655 - 2900 3260 - 3267 3332 - 3339 3345.8 - 3358 3600 - 4400 GHz 4.5 - 5.15 5.35 - 5.46 7.25 - 7.75 8.025 - 8.5 9.0 - 9.2 9.3 - 9.5 10.6 - 12.7 13.25 - 13.4 14.47 - 14.5 15.35 - 16.2 17.7 - 21.4 22.01 - 23.12 23.6 - 24.0 31.2 - 31.8 36.43 - 36.5
(2) 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6
(b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 7 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 3.5 DESCRIPTION OF TEST MODES The EUT (model: SZ-DWS04) had been tested under operating condition. Test program used to control the EUT for staying in continuous transmitting mode was programmed. After verification, all tests were carried out with the worst case test modes as shown below except radiated spurious emission below 1GHz, which worst case was in transmitting mode only. Channel Low (2405MHz), Channel Mid-1 (2445MHz), Channel Mid-2 (2475MHz) and Channel High (2480MHz) were chosen for the final testing. Channel Mid-2 (2475MHz) was chosen for the final testing as per client requested. The field strength of spurious emission was measured in the following position: EUT stand-up position (Z axis), lie-down position (X, Y axis). The worst emission was found in stand-up position (X axis) and the worst case was recorded. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 8 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 4. INSTRUMENT CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement Conducted Emissions Test Site Name of Equipment Manufacturer Spectrum Analyzer Spectrum Analyzer Spectrum Analyzer Agilent Agilent R&S Anritsu Anritsu Power meter Power Sensor Model E4446A N9010A FSL ML2495A MA2411B Serial Number Calibration Due MY48250064 MY52220817 01/01/2015 03/20/2015 11/11/2014 09/29/2014 09/29/2014 100837 1033009 0917221 3M Semi Anechoic Chamber Name of Equipment Manufacturer Spectrum Analyzer Spectrum Analyzer Agilent R&S HP Model E4446A FSL 8447D Serial Number Calibration Due MY48250064 EMI Test Receiver SCHAFFNER SCR 3501 Pre-Amplifier Pre-Amplifier Pre-Amplifier Pre-Amplifier Loop Antenna Bilog Antenna Horn Antenna Horn Antenna Antenna Tower Turn Table Test S/W EMEC MITEQ Agilent EM01M26G AMF-6F-26040 0-40-8P 8449B EMCO TESEQ EMCO EMCO CCS CCS 6502 CBL 6112D 3115 3116 CC-A-1F CC-T-1F 100837 2944A06530 060570 985646 3008A01738 430 8905-2356 35378 00022250 00026370 N/A N/A EZ-EMC 01/01/2015 11/11/2014 05/02/2015 07/28/2015 08/08/2014 08/01/2015 03/30/2015 08/20/2014 09/11/2014 07/25/2015 12/29/2014 N.C.R N.C.R NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. N.C.R = No Calibration Request. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 9 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 4.3 MEASUREMENT UNCERTAINTY Parameter Uncertainty Powerline Conducted Emission 3M Semi Anechoic Chamber / 30MHz ~ 200MHz 3M Semi Anechoic Chamber / 200MHz ~ 1GHz 3M Semi Anechoic Chamber / 1 ~ 8GHz 3M Semi Anechoic Chamber / 8 ~ 18GHz 3M Semi Anechoic Chamber / 18 ~ 26GHz 3M Semi Anechoic Chamber / 26 ~ 40GHz N/A 3.5921 3.5657 2.5873 2.6646 2.9617 3.4250 Remark: This uncertainty represents an expanded uncertainty expressed at approximately the 95%
confidence level using a coverage factor of k=2. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 10 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 5. FACILITIES AND ACCREDITATIONS 5.1 FACILTIES All measurement facilities used to collect the measurement data are located at No. 163-1, Jhongsheng Rd., Sindien District, Taipei City 23151, Taiwan Tel:
886-2-2217-0894 / Fax: 886-2-2217-1029 No 11, Wugong 6th Rd, Wugu District, New Taipei City 24891, Taiwan (R.O.C) Tel: 886-2-2299-9720 / Fax: 886-2-2298-4045 No.81-1, Lane 210, Bade 2nd Rd., Lujhu Township, Taoyuan County 33841,Taiwan, R.O.C. Tel: 886-3-324-0332 / Fax: 886-3-324-5235 The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, Radio Interference Measuring Apparatus and Measurement Methods. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 11 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 5.3 TABLE OF ACCREDITATIONS AND LISTINGS Country Agency Scope of Accreditation Logo USA A2LA CFR 47, FCC Part15/18, CISPR 22, EN 55022, ICES-003, AS/NZS CISPR 22, VCCI V-3, EN 55011, CISPR 11, IEC/EN 61000-4-2/3/4/5/6/8/11, EN 61000-6-1/2/3/4, EN 55024, CISPR 24, AS/NZS CISPR 24, AS/NZS 61000.6.2, EN 55014-1/-2, ETSI EN 300 386 v1.3.2/v1.3.3, IEC/EN 61000-3-2, AS/NZS 61000.3.2, IEC/EN 61000-3-3, AS/NZS 61000.3.3 USA FCC MRA 3 meter Open Area Test Sites to perform FCC Part 15/18 measurements TW1026 Japan VCCI 3/10 meter Open Area Test Sites and conducted test sites to perform radiated/conducted measurements R-2882/2541/2798/725/1868 C-402/747/912 T-1930/1646 Taiwan TAF EN 55014-1, CISPR 14, CNS 13781-1, EN 55013, CISPR 13, CNS 13439, EN 55011, CISPR 11, CNS 13803, PLMN09, IS2045-0, LP0002 FCC Part 27/90, Part 15B/C/D/E, RSS-192/193/210/310 ETSI EN 300 328/ 300 220-1/ 300 220-2/ 301 893/ 301 489-01/ 301 489-03/ 301 489-07 /
301 489-17/ 300 440-1/ 300 440-2 AS/NZS 4268, AS/NZS 4771 CISPR 22, EN 55022, CNS 13438, AS/NZS CISPR 22, VCCI, IEC/EN 61000-4-2/3/4/5/6/8/11, CNS 14676-2/3/4/5/6/8, CNS 14934-2/3, CNS 13783-1, CNS 13439, CNS 13803 Taiwan BSMI CNS 13438, CNS 13783-1, CNS 13439, CNS 14115 Canada Industry Canada RSS-Gen Issue 3 SL2-IS-E-0014 / IN-E-0014
/A1-E-0014 /R1-E-0014
/R2-E-0014 /L1-E-0014 IC 2324C-5 Note: No part of this report may be used to claim or imply product endorsement by A2LA, TAF or other government agency. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 12 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT For Conducted and Radiated (Above 1GHz) Emission Measurement:
No. Device Type Series No. FCC ID Model 1. Default Hostname ISA3 N/A N/A Brand ember 2 Notebook PC D400 0932RY E2K24GBRL DELL For Radiated (Below 1GHz) Emission measurement:
Data Cable Power Cord Unshielded, 0.2m LAN Cable:
Unshielded, 1.5m USB Cable:
Shielded, 2.0m N/A I/P:
Unshielded, 1.8m O/P:
Unshielded, 1.8m No. Device Type Model Series No. FCC ID Brand Data Cable Power Cord N/A
**No any support equipment during the test. Remark: Grounding was established in accordance with the manufacturers requirements and conditions for the intended use. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 13 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 7. FCC PART 15.247 REQUIREMENTS 7.1 6dB BANDWIDTH LIMIT According to 15.247(a)(2), systems using digital modulation techniques may operate in the 902 - 928 MHz, 2400 - 2483.5 MHz, and 5725 - 5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. TEST CONFIGURATION EUT Spectrum Analyzer TEST PROCEDURE 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the spectrum analyzer as RBW = 100kHz, VBW = 300kHz, Span = 3MHz, Sweep
= auto. 4. Mark the peak frequency and 6dB (upper and lower) frequency. 5. Repeat until all the rest channels are investigated. TEST RESULTS No non-compliance noted TEST DATA Channel Low Mid-1 Mid-2 High Frequency
(MHz) Bandwidth (MHz) 2405 2445 2475 2480 1.638 1.617 1.590 1.590 Limit
(kHz)
>500 Result PASS PASS PASS PASS This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 14 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Test Plot 6dB Bandwidth (CH Low) 6dB Bandwidth (CH Mid-1) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 15 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 6dB Bandwidth (CH Mid-2) 6dB Bandwidth (CH High) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 16 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 7.2 PEAK POWER LIMIT The maximum peak output power of the intentional radiator shall not exceed the following:
1. According to 15.247(b)(3), for systems using digital modulation in the bands of 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz: 1 Watt. 2. According to 15.247(b)(4), the conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section, if transmitting antennas of directional gain greater than 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs
(b)(1), (b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the antenna exceeds 6 dBi. TEST CONFIGURATION EUT Power Meter TEST PROCEDURE Per KDB 558074 V03r01 The transmitter output is connected to the Power Meter. The Power Meter is set to the peak power detection. TEST RESULTS No non-compliance noted TEST DATA Channel Low Mid-1 Mid-2 High Frequency
(MHz) 2405 2445 2475 2480 Output Power
(dBm) 11.17 10.56 10.02 1.83 Output Power
(W) 0.0131 0.0114 0.0100 0.0015 Limit
(W) 1 Test Result PASS PASS PASS PASS This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 17 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 7.3 AVERAGE POWER LIMIT None; for reporting purposes only. TEST CONFIGURATION EUT Power Meter TEST PROCEDURE Per KDB 558074 V03r01 The transmitter output is connected to the Power Meter. The Power Meter is set to the peak power detection. TEST RESULTS No non-compliance noted TEST DATA Channel Low Mid-1 Mid-2 High Frequency
(MHz) 2405 2445 2475 2480 Output Power
(dBm) 7.45 7.27 6.89
-1.08 Output Power
(W) 0.0056 0.0053 0.0049 0.0008 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 18 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 7.4 BAND EDGES MEASUREMENT LIMIT According to 15.247(d), in any 100 kHz bandwidth outside the frequency bands in which the spread spectrum intentional radiator in operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. In addition, radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see Section 15.205(c)). TEST CONFIGURATION Antenna tower EUT 3m 4m Horn antenna Spectrum analyzer Turntable 0.8m 1m 30cm Pre-amp TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above the ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. out the highest emission. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find 4. Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission:
(a) PEAK: RBW=1MHz / VBW=3MHz / Sweep=100ms
(b) AVERAGE: RBW=1MHz / VBW=300Hz / Sweep=AUTO 5. Repeat the procedures until all the PEAK and AVERAGE versus POLARIZATION are measured. TEST RESULTS Refer to attach spectrum analyzer data chart. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 19 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Test Plot Band Edges (CH Low) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 20 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 21 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Band Edges (CH High) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 22 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 23 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 7.5 PEAK POWER SPECTRAL DENSITY LIMIT 1. According to 15.247(e), for digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. 2. According to 15.247(f), the digital modulation operation of the hybrid system, with the frequency hopping turned off, shall comply with the power density requirements of paragraph (d) of this section. TEST CONFIGURATION EUT Spectrum Analyzer TEST PROCEDURE Per KDB 558074 V03r01 1. Place the EUT on the table and set it in transmitting mode.Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 2. Set the spectrum analyzer as RBW = 3kHz, VBW = 10kHz, Span = 3MHz, Sweep=
auto. 3. Record the max. reading. 4. Repeat the above procedure until the measurements for all frequencies are completed. TEST RESULTS No non-compliance noted TEST DATA Channel Frequency
(MHz) Low Mid-1 Mid-2 High 2405 2445 2475 2480 Limit
(dBm) Result 8.00 PASS PPSD
(dBm)
-7.304
-7.139
-7.302
-15.976 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 24 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Test Plot PPSD (CH Low) PPSD (CH Mid-1) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 25 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 PPSD (CH Mid-2) PPSD (CH High) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 26 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 7.6 SPURIOUS EMISSIONS 7.6.1 CONDUCTED MEASUREMENT LIMIT According to 15.247(d), in any 100 kHz bandwidth outside the frequency bands in which the spread spectrum intentional radiator in operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. In addition, radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see Section 15.205(c)). TEST CONFIGURATION EUT Spectrum Analyzer TEST PROCEDURE Conducted RF measurements of the transmitter output were made to confirm that the EUT antenna port conducted emissions meet the specified limit and to identify any spurious signals that require further investigation or measurements on the radiated emissions site. The transmitter output is connected to the spectrum analyzer. The resolution bandwidth is set to 100 kHz. The video bandwidth is set to 100 kHz. Measurements are made over the 30MHz to 26GHz range with the transmitter set to the lowest, middle, and highest channels. TEST RESULTS No non-compliance noted. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 27 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Test Plot Spurious Emissions CH Low CH Mid-1 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 28 Rev.00 CH Mid-2 CH High Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 29 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Conducted band-edge CH Low CH High This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 30 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 7.6.2 RADIATED EMISSIONS LIMIT 1. According to 15.209(a), except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table:
Frequency
(MHz) 0.009 - 0.490 0.490 - 1.705 1.705 30.0 30-88 88-216 216-960 Above 960 Field Strength
(V/m) 2400/F(kHz) 24000/F(kHz) 30 100 150 200 500 Measurement Distance
(m) 300 30 30 3 3 3 3 Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 2. In the above emission table, the tighter limit applies at the band edges. Frequency
(MHz) 0.009 - 0.490 0.490 - 1.705 1.705 30.0 30-88 88-216 216-960 Above 960 Field Strength
(V/m at 3-meter) 2400/F(kHz) +80 24000/F(kHz) +40 Field Strength
(dBV/m at 3-meter) 20LOG((2400/F(kHz))+80) 20LOG((24000/F(kHz))+40) 30 100 150 200 500 69.54 40 43.5 46 54 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 31 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Test Configuration Below 1 GHz EUT 3m 4m Turntable 0.8m 1m Reference ground plane Above 1 GHz EUT 3m 4m Antenna tower Bi-log antenna Spectrum analyzer Antenna tower Horn antenna Spectrum analyzer Turntable 0.8m 1m 30cm Pre-amp This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 32 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as:
Below 30MHz RBW=10kHz / VBW=30kHz / Sweep=AUTO 30 ~ 1000MHz:
RBW=100kHz / VBW=300KHz / Sweep=AUTO Above 1GHz:
a) PEAK: RBW=1MHz / VBW=3MHz / Sweep=AUTO b) AVERAGE: RBW=1MHz / VBW=300Hz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 33 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Correction Factor
(dB/m)
-20.71 Result
(dBuV/m) 22.49 Limit
(dBuV/m) 40.00 Margin
(dB)
-17.51 Ant. Pol.
(H/V) Remark V QP
= Emission frequency in MHz
= Uncorrected Analyzer / Receiver reading
= Antenna factor Amplifier gain + Cable loss
= Reading (dBuV) + Corr. Factor (dB/m)
= Limit stated in standard
= Result (dBuV/m) Limit (dBuV/m)
= Quasi-Peak Freq.
(MHz) x.xx x.xx Reading
(dBuV) 45.25 32.33 Correct Factor
(dB/m) 6.91 6.91 Result
(dBuV/m) 52.16 39.24 Limit
(dBuV/m) 74.00 54.00 Margin
(dB)
-21.84
-14.76 Ant. Pol H/V H H Remark peak AVG
= Emission frequency in MHz
= Uncorrected Analyzer / Receiver reading
= Antenna factor + Cable loss Amplifier gain
= Reading (dBuV) + Corr. Factor (dB/m)
= Limit stated in standard
= Result (dBuV/m) Limit (dBuV/m) DATA SAMPLE Below 1 GHz Frequency
(MHz) x.xx Reading
(dBuV) 43.20 Frequency (MHz) Reading (dBuV) Correction Factor (dB/m) Result (dBuV/m) Limit (dBuV/m) Margin (dB) Q.P. Above 1 GHz Frequency (MHz) Reading (dBuV) Correction Factor (dB/m) Result (dBuV/m) Limit (dBuV/m) Margin (dB) TEST RESULTS No non-compliance noted. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 34 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 TEST DATA Below 1GHz Operation Mode:
Temperature:
Humidity:
Normal Link 26C 56% RH Test Date:
Tested by:
Polarity:
2014/7/31 Francis Lee Ver. / Hor. Frequency
(MHz) 80.4399 200.7199 493.6600 635.2799 748.7698 929.1900 80.4400 119.2400 200.7200 504.3300 721.6100 874.8700 Remark:
Reading
(dBuV) 40.60 30.60 23.80 23.90 24.90 23.40 31.30 26.20 29.20 24.80 23.50 22.50 Correction Factor
(dB/m)
-19.90
-16.55
-9.34
-7.63
-6.04
-3.54
-19.90
-15.22
-16.55
-9.16
-6.64
-4.19 Result
(dBuV/m) 20.70 14.05 14.46 16.27 18.86 19.86 11.40 10.98 12.65 15.64 16.86 18.31 Limit
(dBuV/m) 40.00 43.50 46.00 46.00 46.00 46.00 40.00 43.50 43.50 46.00 46.00 46.00 Margin
(dB)
-19.30
-29.45
-31.54
-29.73
-27.14
-26.14
-28.60
-32.52
-30.85
-30.36
-29.14
-27.69 Ant. Pol.
(H/V) Remark V V V V V V H H H H H H QP QP QP QP QP QP QP QP QP QP QP QP 1. No emission found between lowest internal used / generated frequency to 30 MHz. (9kHz ~ 30MHz) 2. Measuring frequencies from 9 kHz to the 1GHz. 3. Radiated emissions measured in the measured frequency range were made with an instrument using peak detector or quasi-peak detector mode. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. The IF bandwidth of SPA between 30MHz to 1GHz was 100kHz. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 35 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Above 1 GHz Operation Mode:
Temperature:
Humidity:
Freq.
(MHz) 1522.000 1960.000 2458.000 2910.000 3600.000 4810.000 7425.000 1388.000 2198.000 2460.000 2742.000 4315.000 4810.000 4810.000 7330.000 Remark:
Reading
(dBuV) 50.24 50.07 51.57 48.27 40.10 45.21 39.41 50.45 49.72 52.10 49.12 39.71 48.78 43.78 38.69 TX / CH Low 26C 56 % RH Test Date:
Tested by:
Polarity:
2014/7/29 Francis Lee Ver. / Hor. Correct Factor
(dB/m)
-5.16
-1.93
-1.24
-0.72 2.93 2.35 11.36
-7.21
-3.56
-4.83
-3.00 7.55 5.62 5.62 11.67 Result
(dBuV/m) 45.08 48.14 50.33 47.55 43.03 47.56 50.77 43.24 46.16 47.27 46.12 47.26 54.40 49.40 50.36 Limit
(dBuV/m) 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 54.00 74.00 Margin
(dB)
-28.92
-25.86
-23.67
-26.45
-30.97
-26.44
-23.23
-30.76
-27.84
-26.73
-27.88
-26.74
-19.60
-4.60
-23.64 Ant. Pol H/V V V V V V V V H H H H H H H H Remark peak peak peak peak peak peak peak peak peak peak peak peak peak AVG peak 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 36 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Operation Mode:
Temperature:
Humidity:
Freq.
(MHz) 1542.000 2198.000 2888.000 3655.000 4890.000 7505.000 1406.000 2144.000 2952.000 3855.000 4890.000 4890.000 7290.000 Remark:
Reading
(dBuV) 50.67 50.02 48.40 42.36 44.89 38.73 51.41 49.40 48.74 39.44 49.26 39.84 38.95 TX / CH Mid-1 26C 56 % RH Test Date:
Tested by:
Polarity:
2014/7/29 Francis Lee Ver. / Hor. Correct Factor
(dB/m)
-5.06
-1.37
-0.83 2.68 4.15 11.56
-7.03
-3.68
-1.17 5.17 6.98 6.98 11.69 Result
(dBuV/m) 45.61 48.65 47.57 45.04 49.04 50.29 44.38 45.72 47.57 44.61 56.24 46.82 50.64 Limit
(dBuV/m) 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 54.00 74.00 Margin
(dB)
-28.39
-25.35
-26.43
-28.96
-24.96
-23.71
-29.62
-28.28
-26.43
-29.39
-17.76
-7.18
-23.36 Ant. Pol H/V V V V V V V H H H H H H H Remark peak peak peak peak peak peak peak peak peak peak peak AVG peak 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 37 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Operation Mode:
Temperature:
Humidity:
Freq.
(MHz) 1552.000 2016.000 2928.000 3795.000 4950.000 7425.000 1416.000 2116.000 2858.000 3865.000 4950.000 4950.000 7345.000 Remark:
Reading
(dBuV) 50.48 49.71 48.93 40.56 42.53 39.18 50.88 49.76 49.27 40.50 48.73 44.31 39.66 TX / CH Mid-2 26C 56 % RH Test Date:
Tested by:
Polarity:
2014/7/29 Francis Lee Ver. / Hor. Correct Factor
(dB/m)
-5.02
-1.66
-0.84 3.63 4.85 11.36
-7.24
-3.74
-2.04 5.18 7.37 7.37 11.59 Result
(dBuV/m) 45.46 48.05 48.09 44.19 47.38 50.54 43.64 46.02 47.23 45.68 56.10 51.68 51.25 Limit
(dBuV/m) 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 54.00 74.00 Margin
(dB)
-28.54
-25.95
-25.91
-29.81
-26.62
-23.46
-30.36
-27.98
-26.77
-28.32
-17.90
-2.32
-22.75 Ant. Pol H/V V V V V V V H H H H H H H Remark peak peak peak peak peak peak peak peak peak peak peak AVG peak 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 38 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Operation Mode:
Temperature:
Humidity:
Freq.
(MHz) 1582.000 2214.000 2904.000 3790.000 5390.000 7395.000 1392.000 2136.000 2848.000 3885.000 4960.000 7295.000 Remark:
Reading
(dBuV) 51.43 50.50 48.62 40.02 40.21 38.91 50.38 49.85 48.59 40.20 42.99 39.22 TX / CH High 26C 56 % RH Test Date:
Tested by:
Polarity:
2014/7/29 Francis Lee Ver. / Hor. Correct Factor
(dB/m)
-4.87
-1.36
-0.69 3.57 6.27 11.26
-7.11
-3.70
-2.12 5.20 7.41 11.75 Result
(dBuV/m) 46.56 49.14 47.93 43.59 46.48 50.17 43.27 46.15 46.47 45.40 50.40 50.97 Limit
(dBuV/m) 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 Margin
(dB)
-27.44
-24.86
-26.07
-30.41
-27.52
-23.83
-30.73
-27.85
-27.53
-28.60
-23.60
-23.03 Ant. Pol H/V V V V V V V H H H H H H Remark peak peak peak peak peak peak peak peak peak peak peak peak 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 39 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 7.7 POWERLINE CONDUCTED EMISSIONS LIMIT According to 15.207(a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 H/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Frequency Range
(MHz) 0.15 to 0.50 Limits
(dBV) Quasi-peak 66 to 56*
Average 56 to 46*
46 50 0.50 to 5 5 to 30 56 60
* Decreases with the logarithm of the frequency. TEST CONFIGURATION See test photographs attached in Appendix II for the actual connections between EUT and support equipment. TEST PROCEDURE 1. The EUT was placed on a table, which is 0.8m above ground plane. 2. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 3. Repeat above procedures until all frequency measured were complete. TEST RESULTS Not applicable, because the EUT is not connected to AC Main Source directly This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 40 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 8. APPENDIX I PHOTOGRAPHS OF TEST SETUP Radiated Emission Set up Photos Below 1GHz This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 41 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Above 1GHz This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 42 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Conducted Emission Setup Photos This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 43 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 APPENDIX 1: PHOTOGRAPHS OF EUT Refer to T140725D05 External Photographs. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 44 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 APPENDIX 2: REMARKS Question:
The peak / avg powers seem to be inconsistent with the power levels shown on the bandedge tests . The graph below suggests Channel 11 power to be about ~3dBm
( assuming 98dBuV/m ), which clearly isnt 11 or 7dBm ( tables on page 17/18 ) Spurious emissions ( Page 28 ) clearly show yet another power level, Marker 1, clearly stated as 3.853dBm , though this is NOT even a valid channel ( 2.412 GHz ), Channel 12 is 2410, channel 13 is 2415, so this isnt a valid frequency for Zigbee. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 45 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RP1 FCC ID: P27SZDWS04 Date of Issue: August 5, 2014 Channel Mid 1 is defined in the document as 2445MHz. However, this plot shows Mid 1 at 2439 , also only showing 3.149dBm !! This doesnt make the >10dBm as previously Answer:
1. Peak / AVG output power , Bandedge , Conducted spurious have different result of fundamantal emission, because of the different test method, (power meter , Radiated method of SA , Conducted method of SA). 2. For Conducted Spurious, the markers of fundamantal emission get imprecise frequency points, because of wide frequency span 26GHz of SA setting. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 46 Rev.00
| 1 | Test Setup Photos | Test Setup Photos | 285.36 KiB | September 23 2014 |
Compliance Certification Services Inc. Report No.: T140725D05-RC1 IC ID: 5604A-SZDWS04 Date of Issue: August 5, 2014 8. APPENDIX I PHOTOGRAPHS OF TEST SETUP Radiated Emission Set up Photos Below 1GHz This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 41 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RC1 IC ID: 5604A-SZDWS04 Above 1GHz Date of Issue: August 5, 2014 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 42 Rev.00 Compliance Certification Services Inc. Report No.: T140725D05-RC1 IC ID: 5604A-SZDWS04 Conducted Emission Setup Photos Date of Issue: August 5, 2014 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 43 Rev.00
| 1 | Tune Up | Parts List/Tune Up Info | 19.70 KiB | September 23 2014 |
Snap-on Diagnostics Tune up procedure The output power setting of EUT is set in the factory and followed the max level in below. There is no tune up procedure except factory default setting:
5.1 dBm 2dB Kevin Kuo Sr. Manager / R&D Division Sercomm Corporation TEL: 886-2-2655-3988#2631 FAX: 886-2-2655-7379 E-Mail: kevin_kuo@sercomm.com
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2014-09-23 | 2405 ~ 2480 | DTS - Digital Transmission System | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2014-09-23
|
||||
| 1 | Applicant's complete, legal business name |
Sercomm Corporation
|
||||
| 1 | FCC Registration Number (FRN) |
0015548027
|
||||
| 1 | Physical Address |
8F, No. 3-1, YuanQu St, NanKang
|
||||
| 1 |
Taipei, N/A
|
|||||
| 1 |
Taiwan
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
V******@babt.com
|
||||
| 1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
P27
|
||||
| 1 | Equipment Product Code |
SZDWS04
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
N**** W********
|
||||
| 1 | Title |
Engineer
|
||||
| 1 | Telephone Number |
886-2******** Extension:
|
||||
| 1 | Fax Number |
886-2********
|
||||
| 1 |
N******@SERCOMM.COM
|
|||||
| app s | Technical Contact | |||||
| n/a | ||||||
| app s | Non Technical Contact | |||||
| n/a | ||||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | DTS - Digital Transmission System | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Micro Door Window Sensor | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Grant Comments | Output power is conducted. | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
Compliance Certification Services Inc.
|
||||
| 1 | Name |
K**** C******
|
||||
| 1 | Telephone Number |
886-3******** Extension:
|
||||
| 1 | Fax Number |
886-3********
|
||||
| 1 |
k******@ccsrf.com
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 15C | 2405.00000000 | 2480.00000000 | 0.0131000 | ||||||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC