FCC ID: P27SSH1R0 Window Sensor

SD-DWS07 Door/Window Sensor Installation Guide Introduction Door/Window sensors are designed to secure the perimeter of the residential premise, and provide the ability to add various automation services. The Door/Window sensor, which consists of a magnet that attaches to a door or window, will communicate door events to the home control system or security panel. When the magnet is moved away from the sensor, a signal will be sent to the control panel that communicates the changed state to the security system. Specification Frequency Battery Type 2.4GHz CR2 Battery * 1 Operating Temperature 0 C to 40 C (32F - 104F) at 90% RH Non-condensing Storage Temperature

-10 C to 60 C (14F - 140F) Battery Life Dimension 4 Years (20 trigger events per day @Room Temperature 25C) Sensor Device: 67.5 mm x 24 mm x 20 mm (2" x 1.14" x 0.43") Magnet: 43 mm x 9.5 mm x 15 mm (2" x 0.39" x 0.43") Pairing Sensor Initiate pairing on your home control system or security panel using the instructions provided with it 1. 2. The LED indicator will be lit for every seconds to indicate Pull the exposed plastic tab from the sensor. (Figure 1) the sensor is booting successfully It will blink one time per seconds while attempting to pair with the security panel or home controller. If network is not found after 90 seconds, the sensor will go into sleep mode. To wake the sensor again, you need to use magnet or tamper (Figure 2) to trigger a paring process, and Figure 1 Figure 2 then sensor will repeat steps from 3 to 4. Installation 1. Please make sure that the sensor and magnet is located less than 10 mm from each other. For optimal performance, it is highly 2. 3. recommended to install the Door/Window sensor on the fixed frame and the magnet on the moving part of the door/window. Place the sensor near the top of the door that close to the opening edge of the door. This is the mounting location for the sensor. Use the provided double-sided tape on the sensor. Attach the sensor to the door. Press firmly and hold in place for a few seconds Use provided double-sided tape on the magnet. Make sure the alignment of both sensor and magnet are facing each other (Figure 3). Press firmly and hold in place for a few seconds. Figure 3 Operation The Green Pairing LED will stay off during the normal operation. The sensor is equipped with a tamper switch. If the cover of sensor is removed, the sensor will send an alarm to the home controller or security system. 1 3. 4. 1. 2. Remove sensor cover. Reset to Factory Defaults & Reboot If sensor needs to be factory defaulted (for example, to prepare it for joining with a home controller or security system). 1. 2. 3. 4. 5. Depress the tamper switch before inserting the battery. Insert the battery. The sensor should illuminate the LED once when boot-up/initialization tasks are complete. Release the tamper switch while the LED is illuminated (it will be lit for 4 seconds). The sensor should then Remove the CR2 battery from sensor. reset to factory default settings and begin searching for any available home controller or security system. If you need to reboot the device, remove the battery, depress and release the tamper switch one time, then re-insert the battery. 6. Place the cover back on sensor. Note: Replace Battery with CR2 only. Use of another battery may negatively impact the performance of the product. Certification FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The FCC ID for this device is P27SSH1R0 You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement:

This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. 2

Product Name: Window Sensor ADT Model No.: SSH1R0-29 Input: 3V ===. CR2 FC Made in Taiwan FCCID.:P27SSH1RO

Declaration of Authorization We Name:

Address:

Sercomm Corporation 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. Declare that:

Name Representative of agent:

Agent Company name:

Address:

City:

Country Marlin Chen MRT Technology (Suzhou) Co., Ltd D8 Building, Youxin Industrial Park, No.2 Tian'edang Rd., Wuzhong Economic Development Zone, Suzhou China is authorized to apply for Certification of the following product(s):

Product description: Window Sensor Type designation:

SSH1R0-29xxxxx(the 1st x should be "blank" or "-"; the rest x could be 0 to 9, A to Z, a to z, "blank" or "-", for the marketing purpose) P27SSH1R0 ADT FCC ID:

Trademark:

on our behalf. Date:

Name:

Signature:

December 19, 2019 Nick Wu

Date: December 19, 2019 Federal Communications Commission Authorization and Evaluation Division FCC ID: P27SSH1R0 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

1. BlockDiagram 2. Schematics 3. Operation Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely,

Name: Nick Wu Sercomm Corporation