FCC ID: P27RP131 Wireless PoE Adapter

 

RP131 Wireless PoE Adapter Installation Guide Ver.1.1

,QWURGXFWLRQ

,QWURGXFWLRQ

,QWURGXFWLRQ

,QWURGXFWLRQ Overview The RP131 (Wireless Adapter) is Wireless client with power supply, it supply the power to the IP camera, it also connect the IP camera to your existing Wireless network. Page 1 Physical Details Page 2 Figure 1: RP131(Wireless PoE Adapter) LEDs Power

(Green) Wireless/

WPS On - Normal operation. Off - No power. Green On - Associate to WiFi AP Off - Not associate to WiFi AP Flashing - Transmitting/Receiving Data Amber On - WPS failed (30 sec) Off - No WPS action or WPS Succeed Flashing - WPS is processing (< 2 min) Ethernet

(Green) On - Ethernet connection is active. Off - No Ethernet connection. Flashing - Data is being transmitted or received via the Ethernet Port. PoE

(Amber) On - The PoE powered device (PD) is connected and the port is supplying power successfully Off - No PoE powered device (PD) connected Page 3 Buttons WPS Button Establish a secure connection between the Wireless router (or Access Point) and IP camera Push-Button-Method -

Press and hold the WPS button, but not no more than 3 seconds PIN Method -

Press the WPS button and hold for greater than 3 seconds LAN Port Use a standard LAN cable to connect the RP131 to the IP Camera Page 4 6HWXS 6HWXS

6HWXS 6HWXS The installation allows the RP131 to directly connect to a wireless router (or Wireless Access Point). You can extend the range of your wireless network. Page 5 1. Locate the RP131 near the Wireless Access Point while doing the configuration. 2. Make sure the Wireless Access Point is on and working properly. 3. Plug the RP131 into the AC power slot, then the Power LED will remain on. 4. Plug the IP camera into the AC power slot 5. Connect a standard LAN cable from the RP131 to IP camera 6. Push the WPS button on the Wireless Access Point and make sure the Wireless Access Point is in WPS mode. (The LED on the AP will blink and active for 2 minutes.) 7. Push and hold the WPS button on the RP131 for more than 3 seconds. The WPS LED on the device will start blinking for 2 minutes. The RP131 will automatically associate to the Wireless Access Point with the strongest signal and make connections.) 8. The connection of the RP131 and Wireless Access Point is successfully established after the Wireless LED remains on The RP131 (Wireless PoE Adapter) is now ready for use. Page 6 6SHFLILFDWLRQ 6SHFLILFDWLRQ

6SHFLILFDWLRQ 6SHFLILFDWLRQ Dimensions 91.7(L) x 57(W) x 61.2(H) mm 56.9 Wireless Standards IEEE 802.11 b/g/n Antenna Internal x 2 LEDs PoE Ethernet Interface Ethernet Standards 1 * Power 1 * Wireless / WPS 1 * Ethernet 1 * PoE IEEE802.3 af Class 3 Maximum outpout power : 10 Watts DC 48V, 208mA(maximum) Over current protection Data pin : 1, 2, 3, 6 Power pin : 4, 5, 7, 8 1 * RJ45 LAN Port Auto-negotiation, Auto MDI/MDIX Ethernet specification IEEE802.3, IEEE802.3u, IEEE802.3x AC Input 100 - 240VAC, 50-60 Hz, 0.8A(maximum) Operating Temperature Storage Temperature 0 C to 45 C

-25 C to 70 C Operating 10-90%RH (max) Page 7 Humidity Certifications FCC Part 15 Class B Safety Approvals UL Listed (UL60950-1)/cUL CSA No.22-

60950-01-03 Page 8 1RWLILFDWLRQRI&RPSOLDQFH 1RWLILFDWLRQRI&RPSOLDQFH

1RWLILFDWLRQRI&RPSOLDQFH 1RWLILFDWLRQRI&RPSOLDQFH FCC Information to User FCC Information to User This device complies with part 15 FCC rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference This device complies with part 15 FCC rules.

(2)this device must accept any interference received, including interference that Operation is subject to the following two conditions:

may cause undesired operations. This equipment has been tested and found to comply with the limits for a Class B

(1)this device may not cause harmful interference digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

(2)this device must accept any interference received, installation. This equipment generates, uses and can radiate radio frequency energy including interference that may cause undesired operations. and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. Page 9

 

 

Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12

 

 

CONSTRUCTION PHOTOS OF EUT Page 1 Page 2

 

 

 

 

 

 

SerComm Corporation Taipei Office: 8F, No.3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. TEL: 886-2-2655-3988 FAX: 886-2-2655-3966 Declaration for no non-US channel operation We, SerComm Corp. declare that the device does not support any non-US channels in all the Date:2013/09/06 operational mode(s) for the following product. FCC ID: P27RP131 If you should have any question(s) regarding this declaration, please dont hesitate to contact us. Thank you!

Sep.,06,2013

-----------------------------------------------------

SerComm Corporation Angus Chang/ Manager TEL: 886-2-2655-3988*2598 FAX: 886-2-2655-3965 E-mail: angus_chang@sercomm.com

 

 

SerComm Corporation Taipei Office: 8F, No.3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. TEL: 886-2-2655-3988 FAX: 886-2-2655-3966 Date:2013/09/06 FCC ID: P27RP131 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below:

Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Sep., 06-2013

-----------------------------------------------------

SerComm Corporation Angus Chang/ Manager TEL: 886-2-2655-3988*2598 FAX: 886-2-2655-3965 E-mail: angus_chang@sercomm.com

 

 

SerComm Corporation Taipei Office: 8F, No.3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. TEL: 886-2-2655-3988 FAX: 886-2-2655-3966 Date:2013/09/06 Authorization Letter To whom it may concern:

We, the undersigned SerComm Corp. hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC Approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please dont hesitate to contact us. Thank you!

Sincerely yours, Sep.,06-2013

-----------------------------------------------------

SerComm Corporation Angus Chang/ Manager TEL: 886-2-2655-3988*2598 FAX: 886-2-2655-3965 E-mail: angus_chang@sercomm.com

 

 

FCC ID: P27RP131 Operational Description This device is a Wireless PoE Adapter, which operates in the 2.4GHz frequency spectrum with throughput of up to 300Mbps which OFDM technique will be applied. If the signal to noise ratio is too poor which could not support 300Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by AC adapter. The antenna used in this product is Printed antenna without connector. The other instruction, please have a look at the users manual. Report No.: RF130808D11

 

 

RF EXPOSURE REPORT REPORT NO.: SA130808D11 MODEL NO.: RP131 FCC ID: P27RP131 RECEIVED: Aug. 8, 2013 TESTED: Aug. 15 ~ 22, 2013 ISSUED: Aug. 28, 2013 APPLICANT: SerComm Corp. ADDRESS: 8F,No.3-1,YuangQu St.,NanKang,Taipei 115,Taiwan ,R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services

(H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SA130808D11 1 of 6 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................ 3 1. CERTIFICATION ........................................................................................... 4 RF EXPOSURE LIMIT .................................................................................. 5 2. 3. MPE CALCULATION FORMULA .................................................................. 5 CLASSIFICATION ......................................................................................... 5 4. 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ............... 6 Report No.: SA130808D11 2 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. SA130808D11 REASON FOR CHANGE Original release DATE ISSUED Aug. 28, 2013 Report No.: SA130808D11 3 of 6 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: Wireless PoE Adapter MODEL NO.: RP131 BRAND: SerComm APPLICANT: SerComm Corp. TESTED: Aug. 15 ~ 22, 2013 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test

(EUT) configurations represented herein are true and accurate accounts of the measurements of the samples EMC characteristics under the conditions specified in this report. PREPARED BY APPROVED BY

:

:

( Annie Chang / Supervisor )

, DATE: Aug. 28, 2013

( Ken Liu / Senior Manager )

, DATE: Aug. 28, 2013 Report No.: SA130808D11 4 of 6 Report Format Version 5.0.0 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY

(mW/cm2) AVERAGE TIME

(minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 1500-100,000 F = Frequency in MHz F/1500 1.0 30 30 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA130808D11 5 of 6 Report Format Version 5.0.0 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER

(dBm) 2412 ~ 2462 29.22 ANTENNA GAIN

(dBi) 4.35 DISTANCE

(cm) 20 POWER DENSITY

(mW/cm2) 0.4526 LIMIT

(mW/cm2) 1.00

--- END ---

Report No.: SA130808D11 6 of 6 Report Format Version 5.0.0

 

 

FCC TEST REPORT REPORT NO.: RF130808D11 MODEL NO.: RP131 FCC ID: P27RP131 RECEIVED: Aug. 8, 2013 TESTED: Aug. 15 ~ 22, 2013 ISSUED: Aug. 28, 2013 APPLICANT: SerComm Corp. ADDRESS: 8F,No.3-1,YuangQu St.,NanKang,Taipei 115,Taiwan ,R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services

(H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF130808D11 1 of 55 Report Format Version 5.2.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................ 4 CERTIFICATION .............................................................................................. 5 1. 2. SUMMARY OF TEST RESULTS ..................................................................... 6 2.1 MEASUREMENT UNCERTAINTY ................................................................... 6 3. GENERAL INFORMATION .............................................................................. 7 3.1 GENERAL DESCRIPTION OF EUT ................................................................ 7 3.2 DESCRIPTION OF TEST MODES .................................................................. 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................... 9 3.3 DESCRIPTION OF SUPPORT UNITS .......................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................ 11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................ 12 4. TEST TYPES AND RESULTS ....................................................................... 13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ........................ 13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ...... 13 4.1.2 TEST INSTRUMENTS ................................................................................... 14 4.1.3 TEST PROCEDURES ................................................................................... 15 4.1.4 DEVIATION FROM TEST STANDARD .......................................................... 15 4.1.5 TEST SETUP ................................................................................................. 16 4.1.6 EUT OPERATING CONDITIONS .................................................................. 16 4.1.7 TEST RESULTS ............................................................................................ 17 4.2 CONDUCTED EMISSION MEASUREMENT ................................................. 30 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT .............................. 30 4.2.2 TEST INSTRUMENTS ................................................................................... 30 4.2.3 TEST PROCEDURES ................................................................................... 31 4.2.4 DEVIATION FROM TEST STANDARD .......................................................... 31 4.2.5 TEST SETUP ................................................................................................. 32 4.2.6 EUT OPERATING CONDITIONS .................................................................. 32 4.2.7 TEST RESULTS ............................................................................................ 33 4.3 6dB BANDWIDTH MEASUREMENT ............................................................. 35 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT .......................................... 35 4.3.2 TEST SETUP ................................................................................................. 35 4.3.3 TEST INSTRUMENTS ................................................................................... 35 4.3.4 TEST PROCEDURE ...................................................................................... 35 4.3.5 DEVIATION FROM TEST STANDARD .......................................................... 35 4.3.6 EUT OPERATING CONDITIONS .................................................................. 35 4.3.7 TEST RESULTS ............................................................................................ 36 4.4 CONDUCTED OUTPUT POWER .................................................................. 37 4.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT ................... 37 Report No.: RF130808D11 2 of 55 Report Format Version 5.2.0 4.4.2 TEST SETUP ................................................................................................. 37 4.4.3 TEST INSTRUMENTS ................................................................................... 37 4.4.4 TEST PROCEDURES ................................................................................... 38 4.4.5 DEVIATION FROM TEST STANDARD .......................................................... 38 4.4.6 EUT OPERATING CONDITIONS .................................................................. 38 4.4.7 TEST RESULTS ............................................................................................ 39 4.5 POWER SPECTRAL DENSITY MEASUREMENT ........................................ 41 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT ...................... 41 4.5.2 TEST SETUP ................................................................................................. 41 4.5.3 TEST INSTRUMENTS ................................................................................... 41 4.5.4 TEST PROCEDURE ...................................................................................... 41 4.5.5 DEVIATION FROM TEST STANDARD .......................................................... 41 4.5.6 EUT OPERATING CONDITION ..................................................................... 41 4.5.7 TEST RESULTS ............................................................................................ 42 4.6 CONDUCTED OUT OF BAND EMISSION MEASUREMENT ....................... 43 4.6.1 LIMITS OF CONDUCTED OUT OF BAND EMISSION MEASUREMENT ..... 43 4.6.2 TEST SETUP ................................................................................................. 43 4.6.3 TEST INSTRUMENTS ................................................................................... 43 4.6.4 TEST PROCEDURE ...................................................................................... 43 4.6.5 DEVIATION FROM TEST STANDARD .......................................................... 44 4.6.6 EUT OPERATING CONDITION ..................................................................... 44 4.6.7 TEST RESULTS ............................................................................................ 44 5. PHOTOGRAPHS OF THE TEST CONFIGURATION .................................... 53 INFORMATION ON THE TESTING LABORATORIES ................................... 54 6. APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING 7. CHANGES TO THE EUT BY THE LAB ......................................................... 55 Report No.: RF130808D11 3 of 55 Report Format Version 5.2.0 RELEASE CONTROL RECORD ISSUE NO. RF130808D11 REASON FOR CHANGE Original release DATE ISSUED Aug. 28, 2013 Report No.: RF130808D11 4 of 55 Report Format Version 5.2.0 1. CERTIFICATION PRODUCT: Wireless PoE Adapter MODEL NO.: RP131 BRAND: SerComm APPLICANT: SerComm Corp. TESTED: Aug. 15 ~ 22, 2013 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 15, Subpart C (Section 15.247) ANSI C63.10-2009 found compliance with The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the samples EMC characteristics under the conditions specified in this report. PREPARED BY APPROVED BY

:

:

( Annie Chang / Supervisor )

, DATE: Aug. 28, 2013

( Ken Liu / Senior Manager )

, DATE: Aug. 28, 2013 Report No.: RF130808D11 5 of 55 Report Format Version 5.2.0 2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications:

APPLIED STANDARD: FCC PART 15, SUBPART C (SECTION 15.247) STANDARD SECTION TEST TYPE RESULT REMARK 15.207 15.247(d) 15.209 15.247(d) 15.247(a)(2) 15.247(b) 15.247(e) 15.203 AC Power Conducted Emission PASS Radiated Emissions PASS Meet the requirement of limit. Minimum passing margin is

-16.57dB at 0.16953MHz. Meet the requirement of limit. Minimum passing margin is

-1.0dB at 2390.00 & 2483.50MHz. Band Edge Measurement 6dB bandwidth Conducted power Power Spectral Density Antenna Requirement PASS Meet the requirement of limit. PASS Meet the requirement of limit. PASS Meet the requirement of limit. PASS Meet the requirement of limit. PASS No antenna connector is used. 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2:

MEASUREMENT Conducted emissions Radiated emissions FREQUENCY 150kHz~30MHz 30MHz ~ 1GHz Above 1GHz UNCERTAINTY 2.41 dB 4.00 dB 3.36 dB This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. Report No.: RF130808D11 6 of 55 Report Format Version 5.2.0 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT EUT MODEL NO. POWER SUPPLY MODULATION TYPE Wireless PoE Adapter RP131 AC I/P: 100-240V, 50/60Hz, 0.8A DC O/P: 48V, 0.208A CCK, DQPSK, DBPSK for DSSS 64QAM, 16QAM, QPSK, BPSK for OFDM MODULATION TECHNOLOGY DSSS, OFDM TRANSFER RATE OPERATING FREQUENCY NUMBER OF CHANNEL 802.11b:11/ 5.5/ 2/ 1Mbps 802.11g: 54/ 48/ 36/ 24/ 18/ 12/ 9/ 6Mbps 802.11n: up to 300Mbps 2412 ~ 2462MHz 11 for 802.11b, 802.11g, 802.11n (20MHz) 7 for 802.11n (40MHz) 834.9mW Main: PCB Printed antenna with 4.35dBi gain Aux: PCB Printed antenna with 1.59dBi gain N/A Refer to users manual Refer to note below OUTPUT POWER ANTENNA TYPE DATA CABLE I/O PORTS ACCESSORY DEVICES Note:

1. The EUT incorporates a MIMO function. Physically, the EUT provides two completed transmitters and two receivers. MODULATION MODE TX FUNCTION 802.11b 802.11g 802.11n (20MHz) 802.11n (40MHz) 2TX 2TX 2TX 2TX 2. The above EUT information was declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: RF130808D11 7 of 55 Report Format Version 5.2.0 3.2 DESCRIPTION OF TEST MODES 11 channels are provided for 802.11b, 802.11g and 802.11n (20MHz):

CHANNEL FREQUENCY CHANNEL FREQUENCY 1 2 3 4 5 6 2412MHz 2417MHz 2422MHz 2427MHz 2432MHz 2437MHz 7 8 9 10 11 2442MHz 2447MHz 2452MHz 2457MHz 2462MHz 7 channels are provided for 802.11n (40MHz):

CHANNEL FREQUENCY CHANNEL FREQUENCY 3 4 5 6 2422MHz 2427MHz 2432MHz 2437MHz 7 8 9 2442MHz 2447MHz 2452MHz Report No.: RF130808D11 8 of 55 Report Format Version 5.2.0 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL EUT CONFIGURE MODE APPLICABLE TO RE1G RE<1G PLC APCM OB DESCRIPTION

-

Where NOTE 1: No need to concern of Conducted Emission due to the EUT is powered by batteries. NOTE: The EUT had been pre-tested on the positioned of each 3 axis. RE1G: Radiated Emission above 1GHz PLC: Power Line Conducted Emission OB: Conducted Out-Band Emission Measurement

-

RE<1G: Radiated Emission below 1GHz APCM: Antenna Port Conducted Measurement The worst case was found when positioned on Y-plane for Mode A. The worst case was found when positioned on Z-plane for Mode B. RADIATED EMISSION TEST (ABOVE 1GHz):

Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. MODE 802.11b 802.11g 802.11n (20MHz) 802.11n (40MHz) AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY 1 to 11 1 to 11 1 to 11 3 to 9 1, 6, 11 1, 6, 11 1, 6, 11 3, 6, 9 DSSS OFDM OFDM OFDM MODULATION TYPE DBPSK BPSK BPSK BPSK DATA RATE

(Mbps) 1.0 6.0 6.5 13.5 RADIATED EMISSION TEST (BELOW 1GHz):

Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY 802.11n (40MHz) 3 to 9 6 OFDM MODULATION TYPE BPSK DATA RATE

(Mbps) 13.5 POWER LINE CONDUCTED EMISSION TEST:

Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY 802.11n (40MHz) 3 to 9 6 OFDM MODULATION TYPE BPSK DATA RATE

(Mbps) 13.5 Report No.: RF130808D11 9 of 55 Report Format Version 5.2.0 CONDUCTED OUT-BAND EMISSION MEASUREMENT:

Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. MODE 802.11b 802.11g 802.11n (20MHz) 802.11n (40MHz) AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY 1 to 11 1 to 11 1 to 11 3 to 9 1, 6, 11 1, 6, 11 1, 6, 11 3, 6, 9 DSSS OFDM OFDM OFDM MODULATION TYPE DBPSK BPSK BPSK BPSK DATA RATE

(Mbps) 1.0 6.0 6.5 13.5 ANTENNA PORT CONDUCTED MEASUREMENT:

This item includes all test value of each mode, but only includes spectrum plot of worst value of each mode. Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. MODE 802.11b 802.11g 802.11n (20MHz) 802.11n (40MHz) AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY 1 to 11 1 to 11 1 to 11 3 to 9 1, 6, 11 1, 6, 11 1, 6, 11 3, 6, 9 DSSS OFDM OFDM OFDM MODULATION TYPE DBPSK BPSK BPSK BPSK DATA RATE

(Mbps) 1.0 6.0 6.5 13.5 TEST CONDITION:

APPLICABLE TO RE1G RE<1G PLC OB APCM ENVIRONMENTAL CONDITIONS 26deg. C, 74%RH 26deg. C, 74%RH 25deg. C, 75%RH 25deg. C, 60%RH 25deg. C, 60%RH INPUT POWER TESTED BY 120Vac, 60Hz 120Vac, 60Hz 120Vac, 60Hz 120Vac, 60Hz 120Vac, 60Hz Dalen Dai Dalen Dai Joey Liu Chad Lee Chad Lee Report No.: RF130808D11 10 of 55 Report Format Version 5.2.0 3.3 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID 1 NOTEBOOK COMPUTER DELL E6530 9331GV1 FCC DoC Approved NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS 1 10m UTP LAN cable NOTE: All power cords of the above support units are non shielded (1.8m). EUT

(Powered from adapter) 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST Notebook 10m UTP LAN cable Test Table

*Kept in a remote area Report No.: RF130808D11 11 of 55 Report Format Version 5.2.0 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards:

FCC Part 15, Subpart C (15.247) 558074 D01 DTS Meas Guidance v03r01 662911 D01 Multiple Transmitter Output v01 r02 ANSI C63.10-2009 All test items have been performed and recorded as per the above standards. NOTE: The product has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF130808D11 12 of 55 Report Format Version 5.2.0 4. TEST TYPES AND RESULTS 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table. Other emissions shall be at least 20dB below the highest level of the desired power:

FREQUENCIES

(MHz) FIELD STRENGTH

(microvolts/meter) MEASUREMENT DISTANCE

(meters) 0.009 ~ 0.490 0.490 ~ 1.705 1.705 ~ 30.0 30 ~ 88 88 ~ 216 216 ~ 960 Above 960 2400/F(kHz) 24000/F(kHz) 30 100 150 200 500 300 30 30 3 3 3 3 NOTE:

1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF130808D11 13 of 55 Report Format Version 5.2.0 4.1.2 TEST INSTRUMENTS CALIBRATED UNTIL Feb. 26, 2013 Feb. 25, 2014 Feb. 26, 2013 Feb. 25, 2014 Jan. 03, 2013 Jan. 02, 2014 Mar. 20, 2013 Mar. 19, 2014 May 29, 2013 May 28, 2014 Aug. 19, 2013 Aug. 18, 2014 May 13, 2013 May 12, 2014 DATE 7.6.15.9.2 MODEL NO. TT100 AT100 ADT_Radiated_V VULB 9168 VHBA 9123 8447D 8449B N9038A 137 480 0306 0306 NA SERIAL NO. CALIBRATED 2432A03504 3008A01201 MY51210129 DESCRIPTION &

MANUFACTURER HP Preamplifier HP Preamplifier Agilent TEST RECEIVER Schwarzbeck Antenna Schwarzbeck Antenna ADT. Turn Table ADT. Tower Software SUHNER RF cable Schwarzbeck Horn Antenna Highpass filter Wainwright Instruments ROHDE & SCHWARZ Spectrum Analyzer Anritsu Power Sensor Anritsu Power Meter NOTE: 1. The calibration interval of the above test instruments is 12/24 months. And the BBHA 9120-D1 3.1/18G-10SS CABLE-CH6 NA NA NA MA2411B ML2495A 0842014 0738404 100036 FSP 40 SF102 D130 WHK SN 8 NA calibrations are traceable to NML/ROC and NIST/USA. 2. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 3. The test was performed in Chamber No. 6. 4. The Industry Canada Reference No. IC 7450E-6. 5. The FCC Site Registration No. is 447212. May. 17, 2013 May. 16, 2014 Apr. 24, 2013 Apr. 23, 2014 Apr. 25, 2013 Apr. 24, 2014 NA NA NA NA Report No.: RF130808D11 14 of 55 Report Format Version 5.2.0 4.1.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meters semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE:

1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 100kHz and video bandwidth is 300kHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 1kHz for Average detection (AV) at frequency above 1GHz. 4. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 DEVIATION FROM TEST STANDARD No deviation. Report No.: RF130808D11 15 of 55 Report Format Version 5.2.0 4.1.5 TEST SETUP For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT OPERATING CONDITIONS Set the EUT under transmission/receiving condition continuously at specific channel frequency. Report No.: RF130808D11 16 of 55 Report Format Version 5.2.0 4.1.7 TEST RESULTS ABOVE 1GHz DATA 802.11b CHANNEL TX Channel 1 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) CORRECTION FACTOR

(dB/m)

-3.75

-3.75

-3.64

-3.64 3.73 3.73 CORRECTION NO. FREQ.

(MHz) 1 2 3 4 5 6 2390.00 2390.00

*2412.00

*2412.00 4824.00 4824.00 NO. FREQ.

(MHz)

(dB)

-7.8

-1.0 MARGIN 74.0 54.0 74.0 54.0 LIMIT

(dBuV/m) ANTENNA HEIGHT 305 305 305 305 339 339 TABLE ANGLE

(Degree)

(m) 1.00 H 1.00 H 1.00 H 1.00 H 1.21 H 1.21 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION RAW LEVEL VALUE

(dBuV/m)

(dBuV) 66.2 PK 69.93 53.0 AV 56.73 110.7 PK 114.38 106.9 AV 110.53 54.9 PK 51.16 52.3 AV 48.53 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M RAW EMISSION VALUE

(dBuV) 68.58 55.45 105.87 102.18 47.38 42.98 LEVEL

(dBuV/m) 64.8 PK 51.7 AV 102.2 PK 98.5 AV 51.1 PK 46.7 AV

(m) 1.00 V 1.00 V 1.00 V 1.00 V 1.12 V 1.12 V TABLE ANGLE

(Degree) ANTENNA HEIGHT LIMIT

(dBuV/m)

-22.9

-7.3

-19.1

-1.7 MARGIN

(dB)

-9.2

-2.3 74.0 54.0 1 2 3 4 5 6 2390.00 2390.00

*2412.00

*2412.00 4824.00 4824.00 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 95 95 95 95 78 78 74.0 54.0 FACTOR

(dB/m)

-3.75

-3.75

-3.64

-3.64 3.73 3.73 Report No.: RF130808D11 17 of 55 Report Format Version 5.2.0 CHANNEL TX Channel 6 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ.

(MHz) 1 2 3 4

*2437.00

*2437.00 4874.00 4874.00 NO. FREQ.

(MHz)

(dB) MARGIN 74.0 54.0 LIMIT

(dBuV/m) ANTENNA HEIGHT TABLE ANGLE

(Degree)

(m) 1.00 H 1.00 H 1.37 H 1.37 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M RAW EMISSION LEVEL VALUE

(dBuV/m)

(dBuV) 111.0 PK 114.51 107.1 AV 110.58 54.8 PK 51.06 52.1 AV 48.31 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M RAW EMISSION VALUE

(dBuV) 105.77 101.87 51.23 48.26 LEVEL

(dBuV/m) 102.2 PK 98.3 AV 55.0 PK 52.0 AV

(m) 1.09 V 1.09 V 1.09 V 1.09 V TABLE ANGLE

(Degree) ANTENNA HEIGHT LIMIT

(dBuV/m) 307 307 345 345

-19.0

-2.0

-19.2

-1.9 MARGIN

(dB) CORRECTION FACTOR

(dB/m)

-3.53

-3.53 3.75 3.75 CORRECTION FACTOR

(dB/m)

-3.53

-3.53 3.75 3.75 1 2 3 4 74.0 54.0

*2437.00

*2437.00 4874.00 4874.00 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 80 80 78 78 Report No.: RF130808D11 18 of 55 Report Format Version 5.2.0 CHANNEL TX Channel 11 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) CORRECTION FACTOR

(dB/m)

-3.41

-3.41

-3.32

-3.32 3.74 3.74 CORRECTION NO. FREQ.

(MHz) 1 2 3 4 5 6

*2462.00

*2462.00 2483.50 2483.50 4924.00 4924.00 NO. FREQ.

(MHz)

(dB) MARGIN LIMIT

(dBuV/m) 74.0 54.0 74.0 54.0 ANTENNA HEIGHT

-6.4

-3.4

-21.8

-4.5 150 150 150 150 3 3 TABLE ANGLE

(Degree)

(m) 1.78 H 1.78 H 1.78 H 1.78 H 1.21 H 1.21 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M RAW EMISSION LEVEL VALUE

(dBuV/m)

(dBuV) 110.1 PK 113.55 106.3 AV 109.67 67.6 PK 70.95 50.6 AV 53.93 52.2 PK 48.49 49.5 AV 45.73 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M RAW EMISSION VALUE

(dBuV) 106.39 102.21 66.04 51.72 51.27 48.37 LEVEL

(dBuV/m) 103.0 PK 98.8 AV 62.7 PK 48.4 AV 55.0 PK 52.1 AV

(m) 1.00 V 1.00 V 1.00 V 1.00 V 1.22 V 1.22 V TABLE ANGLE

(Degree) ANTENNA HEIGHT LIMIT

(dBuV/m) MARGIN

(dB) 1 2 3 4 5 6 74.0 54.0 74.0 54.0

*2462.00

*2462.00 2483.50 2483.50 4924.00 4924.00 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 19 19 19 19 340 340

-11.3

-5.6

-19.0

-1.9 FACTOR

(dB/m)

-3.41

-3.41

-3.32

-3.32 3.74 3.74 Report No.: RF130808D11 19 of 55 Report Format Version 5.2.0 802.11g CHANNEL TX Channel 1 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) CORRECTION FACTOR

(dB/m)

-3.75

-3.75

-3.64

-3.64 3.73 3.73 CORRECTION NO. FREQ.

(MHz) 1 2 3 4 5 6 2390.00 2390.00

*2412.00

*2412.00 4824.00 4824.00 NO. FREQ.

(MHz)

(dB)

-4.5

-1.0 MARGIN 74.0 54.0 74.0 54.0 LIMIT

(dBuV/m) ANTENNA HEIGHT 172 172 172 172 338 338 TABLE ANGLE

(Degree)

(m) 1.91 H 1.91 H 1.91 H 1.91 H 1.51 H 1.51 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M RAW EMISSION LEVEL VALUE

(dBuV/m)

(dBuV) 69.5 PK 73.21 53.0 AV 56.72 109.5 PK 113.11 98.8 AV 102.41 54.2 PK 50.42 41.7 AV 37.92 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M RAW EMISSION VALUE

(dBuV) 72.34 56.07 108.52 98.21 51.53 38.89 LEVEL

(dBuV/m) 68.6 PK 52.3 AV 104.9 PK 94.6 AV 55.3 PK 42.6 AV

(m) 1.13 V 1.13 V 1.13 V 1.13 V 1.09 V 1.09 V TABLE ANGLE

(Degree) ANTENNA HEIGHT LIMIT

(dBuV/m)

-19.9

-12.4 74.0 54.0 MARGIN

(dB)

-5.4

-1.7 1 2 3 4 5 6 2390.00 2390.00

*2412.00

*2412.00 4824.00 4824.00 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 96 96 96 96 74 74

-18.7

-11.4 74.0 54.0 FACTOR

(dB/m)

-3.75

-3.75

-3.64

-3.64 3.73 3.73 Report No.: RF130808D11 20 of 55 Report Format Version 5.2.0 CHANNEL TX Channel 6 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ.

(MHz) 1 2 3 4

*2437.00

*2437.00 4874.00 4874.00 NO. FREQ.

(MHz)

(dB) MARGIN 74.0 54.0 LIMIT

(dBuV/m) ANTENNA HEIGHT TABLE ANGLE

(Degree)

(m) 1.86 H 1.86 H 1.52 H 1.52 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M RAW EMISSION LEVEL VALUE

(dBuV/m)

(dBuV) 109.8 PK 113.29 99.0 AV 102.55 54.4 PK 50.68 41.9 AV 38.12 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M RAW EMISSION VALUE

(dBuV) 107.72 97.14 51.62 38.91 LEVEL

(dBuV/m) 104.2 PK 93.6 AV 55.4 PK 42.7 AV

(m) 1.11 V 1.11 V 1.08 V 1.08 V TABLE ANGLE

(Degree) ANTENNA HEIGHT LIMIT

(dBuV/m) 172 172 339 339

-19.6

-12.1 MARGIN

(dB) CORRECTION FACTOR

(dB/m)

-3.53

-3.53 3.75 3.75 CORRECTION FACTOR

(dB/m)

-3.53

-3.53 3.75 3.75 1 2 3 4 74.0 54.0

*2437.00

*2437.00 4874.00 4874.00 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 79 79 75 75

-18.6

-11.3 Report No.: RF130808D11 21 of 55 Report Format Version 5.2.0 CHANNEL TX Channel 11 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) CORRECTION FACTOR

(dB/m)

-3.41

-3.41

-3.32

-3.32 3.74 3.74 CORRECTION NO. FREQ.

(MHz) 1 2 3 4 5 6

*2462.00

*2462.00 2483.50 2483.50 4924.00 4924.00 NO. FREQ.

(MHz)

(dB) MARGIN LIMIT

(dBuV/m) 74.0 54.0 74.0 54.0 ANTENNA HEIGHT

-3.6

-1.0

-19.3

-12.2 175 175 175 175 337 337 TABLE ANGLE

(Degree)

(m) 1.78 H 1.78 H 1.78 H 1.78 H 1.55 H 1.55 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M RAW EMISSION LEVEL VALUE

(dBuV/m)

(dBuV) 109.7 PK 113.06 100.2 AV 103.56 70.4 PK 73.71 53.0 AV 56.31 54.7 PK 50.96 41.8 AV 38.06 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M RAW EMISSION VALUE

(dBuV) 107.42 96.91 68.61 52.11 51.79 38.96 LEVEL

(dBuV/m) 104.0 PK 93.5 AV 65.3 PK 48.8 AV 55.5 PK 42.7 AV

(m) 1.11 V 1.11 V 1.11 V 1.11 V 1.10 V 1.10 V TABLE ANGLE

(Degree) ANTENNA HEIGHT 79 79 79 79 77 77 LIMIT

(dBuV/m) MARGIN

(dB) 1 2 3 4 5 6 74.0 54.0 74.0 54.0

*2462.00

*2462.00 2483.50 2483.50 4924.00 4924.00 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency.

-8.7

-5.2

-18.5

-11.3 FACTOR

(dB/m)

-3.41

-3.41

-3.32

-3.32 3.74 3.74 Report No.: RF130808D11 22 of 55 Report Format Version 5.2.0 802.11n (20MHz) CHANNEL TX Channel 1 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) CORRECTION FACTOR

(dB/m)

-3.75

-3.75

-3.64

-3.64 3.73 3.73 CORRECTION NO. FREQ.

(MHz) 1 2 3 4 5 6 2390.00 2390.00

*2412.00

*2412.00 4824.00 4824.00 NO. FREQ.

(MHz)

(dB)

-1.0

-1.0 MARGIN 74.0 54.0 74.0 54.0 LIMIT

(dBuV/m) ANTENNA HEIGHT 75 75 75 75 198 198 TABLE ANGLE

(Degree)

(m) 1.00 H 1.00 H 1.00 H 1.00 H 1.33 H 1.33 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M RAW EMISSION LEVEL VALUE

(dBuV/m)

(dBuV) 73.0 PK 76.73 53.0 AV 56.71 111.9 PK 115.52 93.6 AV 97.21 48.1 PK 44.35 34.3 AV 30.53 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M RAW EMISSION VALUE

(dBuV) 71.32 52.04 111.21 100.85 49.79 36.17 LEVEL

(dBuV/m) 67.6 PK 48.3 AV 107.6 PK 97.2 AV 53.5 PK 39.9 AV

(m) 1.05 V 1.05 V 1.05 V 1.05 V 1.03 V 1.03 V TABLE ANGLE

(Degree) ANTENNA HEIGHT LIMIT

(dBuV/m)

-25.9

-19.7 74.0 54.0 MARGIN

(dB)

-6.4

-5.7 1 2 3 4 5 6 2390.00 2390.00

*2412.00

*2412.00 4824.00 4824.00 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 220 220 220 220 137 137

-20.5

-14.1 74.0 54.0 FACTOR

(dB/m)

-3.75

-3.75

-3.64

-3.64 3.73 3.73 Report No.: RF130808D11 23 of 55 Report Format Version 5.2.0 CHANNEL TX Channel 6 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ.

(MHz) 1 2 3 4

*2437.00

*2437.00 4874.00 4874.00 NO. FREQ.

(MHz)

(dB) MARGIN 74.0 54.0 LIMIT

(dBuV/m) ANTENNA HEIGHT TABLE ANGLE

(Degree)

(m) 1.22 H 1.22 H 1.32 H 1.32 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M RAW EMISSION LEVEL VALUE

(dBuV/m)

(dBuV) 112.0 PK 115.52 102.1 AV 105.64 48.8 PK 45.08 34.4 AV 30.69 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M RAW EMISSION VALUE

(dBuV) 110.24 100.13 49.63 35.98 LEVEL

(dBuV/m) 106.7 PK 96.6 AV 53.4 PK 39.7 AV

(m) 1.13 V 1.13 V 1.05 V 1.05 V TABLE ANGLE

(Degree) ANTENNA HEIGHT LIMIT

(dBuV/m) 76 76 200 200

-25.2

-19.6 MARGIN

(dB) CORRECTION FACTOR

(dB/m)

-3.53

-3.53 3.75 3.75 CORRECTION FACTOR

(dB/m)

-3.53

-3.53 3.75 3.75 1 2 3 4 74.0 54.0

*2437.00

*2437.00 4874.00 4874.00 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 214 214 141 141

-20.6

-14.3 Report No.: RF130808D11 24 of 55 Report Format Version 5.2.0 CHANNEL TX Channel 11 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) CORRECTION FACTOR

(dB/m)

-3.41

-3.41

-3.32

-3.32 3.74 3.74 CORRECTION NO. FREQ.

(MHz) 1 2 3 4 5 6

*2462.00

*2462.00 2483.50 2483.50 4924.00 4924.00 NO. FREQ.

(MHz)

(dB) MARGIN LIMIT

(dBuV/m) 74.0 54.0 74.0 54.0 ANTENNA HEIGHT

-1.0

-1.4

-24.2

-18.5 77 77 77 77 189 189 TABLE ANGLE

(Degree)

(m) 1.57 H 1.52 H 1.47 H 1.47 H 1.71 H 1.71 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M RAW EMISSION LEVEL VALUE

(dBuV/m)

(dBuV) 113.3 PK 116.74 103.3 AV 106.70 73.0 PK 76.28 52.6 AV 55.95 49.8 PK 46.08 35.5 AV 31.74 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M RAW EMISSION VALUE

(dBuV) 105.65 95.71 72.08 48.63 50.01 36.28 LEVEL

(dBuV/m) 102.2 PK 92.3 AV 68.8 PK 45.3 AV 53.8 PK 40.0 AV

(m) 1.53 V 1.53 V 1.08 V 1.08 V 1.78 V 1.78 V TABLE ANGLE

(Degree) ANTENNA HEIGHT LIMIT

(dBuV/m) MARGIN

(dB) 1 2 3 4 5 6 74.0 54.0 74.0 54.0

*2462.00

*2462.00 2483.50 2483.50 4924.00 4924.00 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 90 90 90 90 129 129

-5.2

-8.7

-20.3

-14.0 FACTOR

(dB/m)

-3.41

-3.41

-3.32

-3.32 3.74 3.74 Report No.: RF130808D11 25 of 55 Report Format Version 5.2.0 802.11n (40MHz) CHANNEL TX Channel 3 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) CORRECTION FACTOR

(dB/m)

-3.75

-3.75

-3.59

-3.59 3.74 3.74 CORRECTION NO. FREQ.

(MHz) 1 2 3 4 5 6 2390.00 2390.00

*2422.00

*2422.00 4844.00 4844.00 NO. FREQ.

(MHz)

(dB)

-1.2

-1.3 MARGIN 74.0 54.0 74.0 54.0 LIMIT

(dBuV/m) ANTENNA HEIGHT 75 75 75 75 203 203 TABLE ANGLE

(Degree)

(m) 1.01 H 1.01 H 1.01 H 1.01 H 1.36 H 1.36 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M RAW EMISSION LEVEL VALUE

(dBuV/m)

(dBuV) 72.8 PK 76.52 52.7 AV 56.45 108.7 PK 112.27 92.5 AV 96.11 48.9 PK 45.12 35.6 AV 31.81 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M RAW EMISSION VALUE

(dBuV) 73.19 52.50 108.51 93.23 50.10 36.52 LEVEL

(dBuV/m) 69.4 PK 48.8 AV 104.9 PK 89.6 AV 53.8 PK 40.3 AV

(m) 1.09 V 1.09 V 1.09 V 1.09 V 1.05 V 1.05 V TABLE ANGLE

(Degree) ANTENNA HEIGHT LIMIT

(dBuV/m)

-25.1

-18.5 74.0 54.0 MARGIN

(dB)

-4.6

-5.3 1 2 3 4 5 6 2390.00 2390.00

*2422.00

*2422.00 4844.00 4844.00 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 216 216 216 216 138 138

-20.2

-13.7 74.0 54.0 FACTOR

(dB/m)

-3.75

-3.75

-3.59

-3.59 3.74 3.74 Report No.: RF130808D11 26 of 55 Report Format Version 5.2.0 CHANNEL TX Channel 6 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ.

(MHz) 1 2 3 4

*2437.00

*2437.00 4874.00 4874.00 NO. FREQ.

(MHz)

(dB) MARGIN 74.0 54.0 LIMIT

(dBuV/m) ANTENNA HEIGHT TABLE ANGLE

(Degree)

(m) 1.23 H 1.23 H 1.36 H 1.36 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M RAW EMISSION LEVEL VALUE

(dBuV/m)

(dBuV) 109.9 PK 113.43 93.7 AV 97.21 50.4 PK 46.63 35.5 AV 31.74 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M RAW EMISSION VALUE

(dBuV) 108.36 92.73 49.89 36.28 LEVEL

(dBuV/m) 104.8 PK 89.2 AV 53.6 PK 40.0 AV

(m) 1.08 V 1.08 V 1.04 V 1.04 V TABLE ANGLE

(Degree) ANTENNA HEIGHT LIMIT

(dBuV/m) 75 75 201 201

-23.6

-18.5 MARGIN

(dB) CORRECTION FACTOR

(dB/m)

-3.53

-3.53 3.75 3.75 CORRECTION FACTOR

(dB/m)

-3.53

-3.53 3.75 3.75 1 2 3 4 74.0 54.0

*2437.00

*2437.00 4874.00 4874.00 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 204 204 138 138

-20.4

-14.0 Report No.: RF130808D11 27 of 55 Report Format Version 5.2.0 CHANNEL TX Channel 9 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) CORRECTION FACTOR

(dB/m)

-3.46

-3.46

-3.32

-3.32 3.76 3.76 CORRECTION NO. FREQ.

(MHz) 1 2 3 4 5 6

*2452.00

*2452.00 2483.50 2483.50 4904.00 4904.00 NO. FREQ.

(MHz)

(dB) MARGIN LIMIT

(dBuV/m) 74.0 54.0 74.0 54.0 ANTENNA HEIGHT

-1.0

-1.0

-24.2

-18.7 76 76 76 76 196 196 TABLE ANGLE

(Degree)

(m) 1.23 H 1.23 H 1.23 H 1.23 H 1.30 H 1.30 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M RAW EMISSION LEVEL VALUE

(dBuV/m)

(dBuV) 108.6 PK 112.06 93.5 AV 96.92 73.0 PK 76.31 53.0 AV 56.28 49.8 PK 46.08 35.3 AV 31.56 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M RAW EMISSION VALUE

(dBuV) 108.92 92.92 72.36 48.98 49.65 36.08 LEVEL

(dBuV/m) 105.5 PK 89.5 AV 69.0 PK 45.7 AV 53.4 PK 39.8 AV

(m) 1.02 V 1.02 V 1.02 V 1.02 V 1.02 V 1.02 V TABLE ANGLE

(Degree) ANTENNA HEIGHT LIMIT

(dBuV/m) MARGIN

(dB) 1 2 3 4 5 6 74.0 54.0 74.0 54.0

*2452.00

*2452.00 2483.50 2483.50 4904.00 4904.00 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 216 216 216 216 140 140

-5.0

-8.3

-20.6

-14.2 FACTOR

(dB/m)

-3.46

-3.46

-3.32

-3.32 3.76 3.76 Report No.: RF130808D11 28 of 55 Report Format Version 5.2.0 BELOW 1GHz WORST-CASE DATA 802.11n (40MHz) CHANNEL TX Channel 6 FREQUENCY RANGE 30MHz ~ 1GHz DETECTOR FUNCTION Quasi-Peak (QP) CORRECTION FACTOR

(dB/m)

-13.56

-11.67

-8.63

-7.69

-6.83

-0.63 CORRECTION NO. 1 2 3 4 5 6 FREQ.

(MHz) 249.22 292.87 435.46 486.87 536.34 897.18 NO. FREQ.

(MHz)

(dB) MARGIN LIMIT

(dBuV/m) ANTENNA HEIGHT 334 219 267 11 259 60 TABLE ANGLE

(Degree) 46.0 46.0 46.0 46.0 46.0 46.0

-9.6

-6.3

-6.5

-7.6

-11.9

-15.4

(m) 1.06 H 1.33 H 1.09 H 1.00 H 1.15 H 1.00 H ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M RAW EMISSION LEVEL VALUE

(dBuV/m)

(dBuV) 36.5 QP 50.01 39.7 QP 51.36 39.5 QP 48.14 38.4 QP 46.10 34.1 QP 40.89 30.6 QP 31.23 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION RAW VALUE

(dBuV) 43.98 44.54 46.13 45.21 44.59 44.08 LEVEL

(dBuV/m) 30.4 QP 32.9 QP 37.6 QP 37.6 QP 37.6 QP 38.0 QP

(m) 1.16 V 1.09 V 1.11 V 1.00 V 1.06 V 1.00 V TABLE ANGLE

(Degree) ANTENNA HEIGHT LIMIT

(dBuV/m) MARGIN

(dB) 1 2 3 4 5 6 43.5 46.0 46.0 46.0 46.0 46.0

-13.1

-13.1

-8.4

-8.4

-8.4

-8.0 165.80 292.87 443.22 492.69 523.73 574.17 REMARKS:

1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 10 117 147 344 247 233 FACTOR

(dB/m)

-13.57

-11.67

-8.50

-7.61

-7.00

-6.04 Report No.: RF130808D11 29 of 55 Report Format Version 5.2.0 4.2 CONDUCTED EMISSION MEASUREMENT 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION (MHz) CONDUCTED LIMIT (dBV) 0.15 ~ 0.5 0.5 ~ 5 5 ~ 30 Quasi-peak 66 to 56 56 60 Average 56 to 46 46 50 NOTE: 1.The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 4.2.2 TEST INSTRUMENTS DESCRIPTION &

MANUFACTURER ROHDE &

SCHWARZ TEST RECEIVER ROHDE & SCHWARZ Artificial Mains Network

(for EUT) LISN With Adapter

(for EUT) ROHDE & SCHWARZ Artificial Mains Network

(for peripherals) Software Software RF cable (JYEBAO) SUHNER Terminator

(For ROHDE &

SCHWARZ LISN) MODEL NO. SERIAL NO. CALIBRATED DATE CALIBRATED UNTIL ESCS 30 100276 Jan. 07, 2013 Jan. 06, 2014 ESH3-Z5 100219 Nov. 28, 2012 Nov. 27, 2013 AD10 C10Ada-001 Nov. 28, 2012 Nov. 27, 2013 ESH3-Z5 100218 Dec. 05, 2012 Dec. 04, 2013 ADT_Cond_V7.3.7 ADT_ISN_V7.3.7 NA NA NA NA NA NA 5D-FB Cable-C10.01 Feb. 19, 2013 Feb. 18, 2014 65BNC-5001 E1-010773 Feb. 06, 2013 Feb. 05, 2014 NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Shielded Room No. 10. 3. The VCCI Site Registration No. C-1852. Report No.: RF130808D11 30 of 55 Report Format Version 5.2.0 4.2.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not recorded. NOTE: All modes of operation were investigated and the worst-case emissions are reported. 4.2.4 DEVIATION FROM TEST STANDARD No deviation. Report No.: RF130808D11 31 of 55 Report Format Version 5.2.0 4.2.5 TEST SETUP Ve r tica l G ro u n d R e fe r en c e P lan e E U T 4 0c m L IS N 8 0c m T es t R ec e iv er H o r iz o n ta l G r o u n d R e fe re n c e P lan e N o te : S u p p o r t u n its w e r e c o n n e cte d to s ec o n d L IS N . For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT OPERATING CONDITIONS Same as item 4.1.6. Report No.: RF130808D11 32 of 55 Report Format Version 5.2.0 4.2.7 TEST RESULTS CONDUCTED WORST-CASE DATA 802.11n (40MHz) PHASE Line 1 6dB BANDWIDTH 9kHz No 1 2 3 4 5 6 Freq.

[MHz]

0.16953 0.25938 0.77109 2.25391 5.31641 23.12891 Corr. Reading Value Emission Level Factor

(dB) 0.14 0.15 0.18 0.24 0.39 1.25

[dB (uV)]

Q.P. AV. 48.28 38.52 40.51 28.73 34.83 22.66 37.25 24.92 32.48 22.96 29.22 25.95

[dB (uV)]

AV. 38.66 28.88 22.84 25.16 23.35 27.20 Q.P. 48.42 40.66 35.01 37.49 32.87 30.47 Limit

[dB (uV)]

AV. 54.98 51.45 46.00 46.00 50.00 50.00 Q.P. 64.98 61.45 56.00 56.00 60.00 60.00 Margin

(dB) Q.P.

-16.57

-20.79

-20.99

-18.51

-27.13

-29.53 AV.

-16.33

-22.57

-23.16

-20.84

-26.65

-22.80 REMARKS:

1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission Level Limit value 4. Correction Factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF130808D11 33 of 55 Report Format Version 5.2.0 PHASE Line 2 6dB BANDWIDTH 9kHz No 1 2 3 4 5 6 Freq.

[MHz]

0.16690 0.29572 0.76719 2.49219 6.55859 23.12891 Corr. Reading Value Emission Level Factor

(dB) 0.11 0.12 0.15 0.21 0.36 0.85

[dB (uV)]

Q.P. AV. 47.69 36.48 39.77 30.94 33.76 20.98 36.75 24.38 32.80 24.34 30.18 27.03

[dB (uV)]

AV. 36.59 31.06 21.13 24.59 24.70 27.88 Q.P. 47.80 39.89 33.91 36.96 33.16 31.03 Limit

[dB (uV)]

AV. 55.11 50.36 46.00 46.00 50.00 50.00 Q.P. 65.11 60.36 56.00 56.00 60.00 60.00 Margin

(dB) Q.P.

-17.32

-20.47

-22.09

-19.04

-26.84

-28.97 AV.

-18.53

-19.30

-24.87

-21.41

-25.30

-22.12 REMARKS:

1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission Level Limit value 4. Correction Factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF130808D11 34 of 55 Report Format Version 5.2.0 4.3 6dB BANDWIDTH MEASUREMENT 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT The minimum of 6dB Bandwidth Measurement is 0.5 MHz. 4.3.2 TEST SETUP EUT SPECTRUM ANALYZER 10dB ATTENUATION PAD 4.3.3 TEST INSTRUMENTS Refer to section 4.1.2 to get information of above instrument. 4.3.4 TEST PROCEDURE a. Set resolution bandwidth (RBW) = 100kHz b. Set the video bandwidth (VBW) 3 x RBW, Detector = Peak. c. Trace mode = max hold. d. Sweep = auto couple. e. Measure the maximum width of the emission that is constrained by the frequencies associated with the two amplitude points (upper and lower) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission 4.3.5 DEVIATION FROM TEST STANDARD No deviation. 4.3.6 EUT OPERATING CONDITIONS The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. Report No.: RF130808D11 35 of 55 Report Format Version 5.2.0 4.3.7 TEST RESULTS CHANNEL 802.11b 1 6 11 802.11g 1 6 11 802.11n (20MHz) 1 6 11 802.11n (40MHz) 3 6 9 CHANNEL FREQUENCY

(MHz) 6dB BANDWIDTH (MHz) CHAIN 0 CHAIN 1 MINIMUM LIMIT (MHz) PASS / FAIL 2412 2437 2462 2412 2437 2462 2412 2437 2462 2422 2437 2452 10.10 10.08 10.13 16.46 16.49 16.48 17.57 17.60 17.62 36.45 36.47 36.44 10.09 10.16 10.13 16.46 16.45 16.47 17.61 17.62 17.61 36.41 36.42 36.37 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS Report No.: RF130808D11 36 of 55 Report Format Version 5.2.0 4.4 CONDUCTED OUTPUT POWER 4.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT For systems using digital modulation in the 24002483.5 MHz bands: 1 Watt

(30dBm) Per KDB 662911 D01 Multiple Transmitter Output v01r02 Method of conducted output power measurement on IEEE 802.11 devices, Array Gain = 0 dB (i.e., no array gain) for NANT 4;

Array Gain = 0 dB (i.e., no array gain) for channel widths 40 MHz for any NANT;

Array Gain = 5 log(NANT/NSS) dB or 3 dB, whichever is less for 20-MHz channel widths with NANT 5. For power measurements on all other devices: Array Gain = 10 log(NANT/NSS) dB. 4.4.2 TEST SETUP EUT 10dB ATTENUATION PAD 4.4.3 TEST INSTRUMENTS Power Sensor Power Meter Refer to section 4.1.2 to get information of above instrument. Report No.: RF130808D11 37 of 55 Report Format Version 5.2.0 4.4.4 TEST PROCEDURES A peak / average power sensor were used on the output port of the EUT. A power meter was used to read the response of the peak / average power sensor. Record the peak power level. 4.4.5 DEVIATION FROM TEST STANDARD No deviation. 4.4.6 EUT OPERATING CONDITIONS Same as Item 4.3.6. Report No.: RF130808D11 38 of 55 Report Format Version 5.2.0 4.4.7 TEST RESULTS FOR PEAK POWER CHAN. FREQ.

(MHz) PEAK POWER (dBm) CHAIN 0 CHAIN 1 TOTAL POWER

(mW) TOTAL POWER

(dBm) LIMIT

(dBm) PASS /

FAIL 802.11b 1 6 11 802.11g 1 6 11 2412 2437 2462 2412 2437 2462 802.11n (20MHz) 1 6 2412 2437 11 2462 802.11 (40MHz) 3 6 9 2422 2437 2452 22.11 21.96 21.69 26.10 25.84 26.37 23.36 24.73 24.01 24.68 24.06 24.15 22.15 22.06 21.79 26.31 26.08 25.63 22.75 24.13 24.15 24.06 23.54 23.74 326.6 317.7 298.6 834.9 789.2 799.1 405.1 556.0 511.8 548.4 480.6 496.6 25.14 25.02 24.75 29.22 28.97 29.03 26.08 27.45 27.09 27.39 26.82 26.96 30 30 30 30 30 30 30 30 30 30 30 30 PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS Report No.: RF130808D11 39 of 55 Report Format Version 5.2.0 FOR AVERAGE POWER CHAN. FREQUENCY

(MHz) AVG. POWER (dBm) CHAIN 0 CHAIN 1 TOTAL POWER

(dBm) 802.11b 1 6 11 802.11g 1 6 11 802.11n (20MHz) 1 6 11 802.11n (40MHz) 3 6 9 2412 2437 2462 2412 2437 2462 2412 2437 2462 2422 2437 2452 18.53 18.39 18.13 17.45 17.27 17.03 15.24 15.26 15.15 15.14 15.41 15.49 18.61 18.47 18.18 17.02 17.29 17.26 15.18 15.19 15.26 15.43 15.03 15.19 21.58 21.44 21.17 20.25 20.29 20.16 18.22 18.24 18.22 18.30 18.23 18.35 Report No.: RF130808D11 40 of 55 Report Format Version 5.2.0 4.5 POWER SPECTRAL DENSITY MEASUREMENT 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT The Maximum of Power Spectral Density Measurement is 8dBm. 4.5.2 TEST SETUP EUT 10dB ATTENUATION PAD SPECTRUM ANALYZER 4.5.3 TEST INSTRUMENTS Refer to section 4.1.2 to get information of above instrument. 4.5.4 TEST PROCEDURE a. Set the RBW = 3 kHz, VBW =10 kHz, Detector = peak. b. Sweep time = auto couple, Trace mode = max hold, allow trace to fully stabilize. c. Use the peak marker function to determine the maximum power level in any 100 kHz band segment within the fundamental EBW. 4.5.5 DEVIATION FROM TEST STANDARD No deviation. 4.5.6 EUT OPERATING CONDITION Same as Item 4.3.6 Report No.: RF130808D11 41 of 55 Report Format Version 5.2.0 Channel Freq.

(MHz) PSD

(dBm/3kHz) 10 log (N=2) dB Total PSD

(dBm/3kHz) Limit

(dBm/3kHz) PASS

/FAIL 4.5.7 TEST RESULTS TX chain 802.11b 0 1 802.11g 0 1 1 6 11 1 6 11 1 6 11 1 6 11 802.11n (20MHz) 0 1 1 6 11 1 6 11 802.11n (40MHz) 0 1 3 6 9 3 6 9 2412 2437 2462 2412 2437 2462 2412 2437 2462 2412 2437 2462 2412 2437 2462 2412 2437 2462 2422 2437 2452 2422 2437 2452

-6.46

-6.30

-5.87

-7.23

-7.50

-7.04

-7.34

-8.27

-7.57

-8.15

-8.83

-8.24

-8.99

-8.79

-7.46

-7.39

-9.11

-8.14

-11.70

-12.23

-11.99

-12.21

-10.67

-13.00 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01 3.01

-3.34

-3.18

-2.75

-4.11

-4.38

-3.92

-3.76

-4.69

-3.99

-4.57

-5.25

-4.66

-4.90

-4.70

-3.37

-3.30

-5.02

-4.05

-6.81

-7.34

-7.10

-7.32

-5.78

-8.11 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 7.91 PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS NOTE: Directional gain = 10 log[(104.35 /20 + 101.59 /20)2 /2] = 6.09dBi > 6dBi , so the power density limit shall be reduced to 8-(6.09-6) = 7.91dBm. Report No.: RF130808D11 42 of 55 Report Format Version 5.2.0 4.6 CONDUCTED OUT OF BAND EMISSION MEASUREMENT 4.6.1 LIMITS OF CONDUCTED OUT OF BAND EMISSION MEASUREMENT Below 20dB of the highest emission level of operating band (in 100kHz Resolution Bandwidth). 4.6.2 TEST SETUP EUT 10dB ATTENUATION PAD SPECTRUM ANALYZER 4.6.3 TEST INSTRUMENTS Refer to section 4.1.2 to get information of above instrument. 4.6.4 TEST PROCEDURE MEASUREMENT PROCEDURE REF 1. Set the RBW = 100 kHz. 2. Set the VBW 300 kHz. 3. Detector = peak. 4. Sweep time = auto couple. 5. Trace mode = max hold. 6. Allow trace to fully stabilize. 7. Use the peak marker function to determine the maximum power level in any 100 kHz band segment within the fundamental EBW. Report No.: RF130808D11 43 of 55 Report Format Version 5.2.0 MEASUREMENT PROCEDURE OOBE 1. Set RBW = 100 kHz. 2. Set VBW 300 kHz. 3. Set span to encompass the spectrum to be examined. 4. Detector = peak. 5. Trace Mode = max hold. 6. Sweep = auto couple. 4.6.5 DEVIATION FROM TEST STANDARD No deviation. 4.6.6 EUT OPERATING CONDITION Same as Item 4.3.6 4.6.7 TEST RESULTS The conducted emission test is performed on each TX port of operating mode without summing or adding 10log (N) since the limit is relative emission limit. The spectrum plots are attached on the following pages. D1 line indicates the highest level, and D2 line indicates the 20dB offset below D1. It shows compliance with the requirement. Report No.: RF130808D11 44 of 55 Report Format Version 5.2.0 CHAIN 0:

802.11b CH 1 CH 6 CH 11 Report No.: RF130808D11 45 of 55 Report Format Version 5.2.0 802.11g CH 1 CH 6 CH 11 Report No.: RF130808D11 46 of 55 Report Format Version 5.2.0 802.11n (20MHz) CH 1 CH 6 CH 11 Report No.: RF130808D11 47 of 55 Report Format Version 5.2.0 802.11n (40MHz) CH 3 CH 6 CH 9 Report No.: RF130808D11 48 of 55 Report Format Version 5.2.0 CHAIN 1:

802.11b CH 1 CH 6 CH 11 Report No.: RF130808D11 49 of 55 Report Format Version 5.2.0 802.11g CH 1 CH 6 CH 11 Report No.: RF130808D11 50 of 55 Report Format Version 5.2.0 802.11n (20MHz) CH 1 CH 6 CH 11 Report No.: RF130808D11 51 of 55 Report Format Version 5.2.0 802.11n (40MHz) CH 3 CH 6 CH 9 Report No.: RF130808D11 52 of 55 Report Format Version 5.2.0 5. PHOTOGRAPHS OF THE TEST CONFIGURATION Please refer to the attached file (Test Setup Photo). Report No.: RF130808D11 53 of 55 Report Format Version 5.2.0 6. INFORMATION ON THE TESTING LABORATORIES We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following:

Linko EMC/RF Lab Tel: 886-2-26052180 Fax: 886-2-26051924 Hwa Ya EMC/RF/Safety/Telecom Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. Hsin Chu EMC/RF Lab Tel: 886-3-5935343 Fax: 886-3-5935342 Report No.: RF130808D11 54 of 55 Report Format Version 5.2.0 7. APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No modifications were made to the EUT by the lab during the test.

---END---

Report No.: RF130808D11 55 of 55 Report Format Version 5.2.0

 

 

PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 1 of 2 RADIATED EMISSION TEST 2 of 2