all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manual | photos | label |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
SZ-BSW01-User Manual | Users Manual | 121.92 KiB | June 19 2013 | |||
1 |
|
SZ-BSW01-Internal Photographs of EUT | Internal Photos | 1.06 MiB | June 19 2013 | |||
1 |
|
SZ-BSW01-External Photographs of EUT | External Photos | 156.20 KiB | June 19 2013 | |||
1 |
|
SZ-BSW01-Label Sample & Location-20130618 | ID Label/Location Info | 681.76 KiB | June 19 2013 | |||
1 | SZ-BSW01-Antenna Specification | Operational Description | June 19 2013 | confidential | ||||
1 | SZ-BSW01-Block Diagram | Block Diagram | June 19 2013 | confidential | ||||
1 |
|
SZ-BSW01-Confidentiality Leter | Cover Letter(s) | 357.61 KiB | June 19 2013 | |||
1 |
|
SZ-BSW01-MPE Report | RF Exposure Info | 45.26 KiB | June 19 2013 | |||
1 |
|
SZ-BSW01-Power of Attorney | Cover Letter(s) | 357.27 KiB | June 19 2013 | |||
1 | SZ-BSW01-Schematics | Schematics | June 19 2013 | confidential | ||||
1 |
|
SZ-BSW01-Test Report | Test Report | 371.70 KiB | June 19 2013 | |||
1 |
|
SZ-BSW01-Test Setup Photo | Test Setup Photos | 409.47 KiB | June 19 2013 | |||
1 | SZ-BSW01-Theroy of operation | Operational Description | June 19 2013 | confidential |
1 | SZ-BSW01-User Manual | Users Manual | 121.92 KiB | June 19 2013 |
SZ-BSW01 ZigBee Binary Switch Installation Guide SZ-BSW01 can provide "smart" lighting remote control with its embedded radio frequency (RF) technology that is compatible with ZigBee enabled devices. This device is designed to give you one-touch control of your home's lighting. In a ZigBee network, each device is designed to act as a router. These routers will re-transmit the RF signal from one device to another until the signal is received by the final destination. Using RF technology ensures SerComm to provide great signal through all the obstacles and radio dead spots. The plug-in Lamp Module of SZ-BSW01 is compatible with any ZigBee enabled network, regardless of the manufacturer and can also be used with other devices with the ZigBee logo. CAUTION: Remember to have common sense while using the remote control, especially when scheduling unattended devices. There can be some unexpected consequences if used without care. For example, if an empty coffee pot is remotely turned on, and your coffee pot could be damaged from overheating. Or if an electric heater is turned on by remote control while clothing is draped over it, it may result a fire. DO NOT USE the remote for controlling the high power heating appliances such as portable heaters. This device will not control lighting used with electronic low-voltage and high frequency power supply transformers, nor high pressure discharge lamps (HID lighting), which include mercury-vapor, sodium vapor and metal halide lamps. DO NOT change location after unit is enrolled in ZigBee network. Specification Rado Frequency RF Communication Range LED Indicator Power Source Output Max Current Dimensions (H x W x D) Operation Temperature Storage Temperature Package Contents 2.4GHz Open Aire100M (Max) Red / Greed LED x 1 Input120 VAC, 0.5A, 50-60 Hz 10A 55 mm x 55 mm x 38 mm (2.15 x 2.15 x 1.48) 0 - 50C (32 - 122F)
-20 - 70C (-4 - 158F) Warnings and Cautions To be installed and/or used in accordance with appropriate electrical codes and regulations. If you are unsure about any part of these instructions, please consult a qualified electrician. 1 To reduce the risk of overheating and possible damage to other equipments, do not install for controlling a motor-operated appliance, fluorescent lighting fixture, or a transformer supplied appliance. Unplug unit when servicing the connected lighting fixtures. Save this instruction sheet. It contains important technical data along with testing and troubleshooting information, which will be useful for future reference. LEDs Power (Red/Green) On (Red) - When ON/OFF button is pressed to ON. Blinking (Green):
The LED will blink for 10 seconds when join/leave function is being processed. The LED will be on for 1 seconds when join/leave function is succeeded and then off Installation NOTE: In order to use SZ-BSW01 in a ZigBee network, the device must be Included into the network by using a Primary Programmer/Remote. Please refer to the Remote Control instruction sheet for complete information. 1. Put the lamps plug into SZ-BSW01. 2. Attach the SZ-BSW01 into wall receptacle. Make sure the receptacle is working properly. If it is controlled by a wall switch, which must be set to ON all the times. WARNING: For use with up to 1000 Watts incandescent lights. 2 Operation 1. ON/OFF Button 2. Join/Leave Button Auto Operation:
NOTE: For complete details on operating by the Remote Control, please refer to the individual devices instruction guide. If a power interruption should occur while the device is ON, the light will return to its previous state when power is restored. ON: This command will turn on the lights to the previous setting. OFF: This command will turn the lights off. MANUAL Operation:
ON: Press the ON/OFF button of the device to turn the lights on. NOTE: The lights will be turned ON regardless of the previous setting. OFF: Press the ON/OFF button to turn the lights off. Joing / Leaving to a ZigBee Network Join Function For "Join" a network, please do the following instruction:
Press the Join/Leave button for less than 1 second. The LED is blinking while processing. If the device has been joined with the controller successfully, the Green LED will be on for 2 seconds and then off. The Green LED will be off instantly if failed. Leave Function For "Leave" a network, please do the following instruction:
Pressed Join/Leave button for 3 seconds to let the SZ-BSW01 be deleted from the ZigBee Coordinator. If the SZ-BSW01 has been deleted successfully, the LED will be on for 1 second and then off. Troubleshooting If the device appears to be functioning improperly, please follow the suggested steps:
1. Confirm that the device is being supplied from a 120V, 60Hz AC source ONLY. 2. Confirm that the device is being controlled in proper way (local switch is ON) and check for burned-out bulbs. 3. Be sure that the lighting does not exceed the current 10A limit. 3 FCC Statement Increase the separation between the equipment and receiver. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. CE Approval CE Standards This product complies with the 99/5/EEC directives, including the following safety and EMC standards:
EN301489-1/-17 EN300328 EN14604 CE Marking Warning This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. UL Notices: This device complies with UL Standard 217. 4
1 | SZ-BSW01-Internal Photographs of EUT | Internal Photos | 1.06 MiB | June 19 2013 |
INTERNAL PHOTOGRAPHS OF EUT Report No: T130522D04 Page 3 Rev.00 Report No: T130522D04 Page 4 Rev.00 Report No: T130522D04 Page 5 Rev.00 Report No: T130522D04 Page 6 Rev.00 Report No: T130522D04 Page 7 Rev.00 Report No: T130522D04 Antenna Page 8 Rev.00
1 | SZ-BSW01-External Photographs of EUT | External Photos | 156.20 KiB | June 19 2013 |
EXTERNAL PHOTOGRAPHS OF EUT Report No: T130522D04 Page 1 / 8 Rev.00 Report No: T130522D04 Page 2 Rev.00
1 | SZ-BSW01-Label Sample & Location-20130618 | ID Label/Location Info | 681.76 KiB | June 19 2013 |
ZigBee Binary Switch SerComm fe | UE Model No.: SZ-BSW01 Input controller = 120VAC, 10.5A, 60K IC: 5604A-SZBSWO1 Pass through Oulet output 120VAC, 0A, 60H E-.0 1F. po7g7BSWO 0010 onuesanygmnmnn C | INDOOR tf ONLY Made in Taiwan
1 | SZ-BSW01-Confidentiality Leter | Cover Letter(s) | 357.61 KiB | June 19 2013 |
SerComm Corporation Taipei Office: 8F, No.3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. TEL: 886-2-2655-3988 FAX: 886-2-2655-3966 Chu Nan Office: 3F, No. 81, YuYi Rd., Chu-Nan, Miao-Li 350, Taiwan, R.O.C. TEL: 886-37-585-899 FAX: 886-37-585-000 DateJune 5, 2013 BABT TCB Forsyth House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD Confidentiality Request FCC ID: P27SZBSW01 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules, SerComm Corporation hereby requests permanent confidential treatment of information accompanying this application as outlined below:
Common exhibits for which confidentiality is requested are:
Schematics Block Diagrams Theory of Operation The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Your Sincerely, Ronnie Cheng Associate Manager / R&D Division SerComm Corporation TEL: 886-2-2655-3988#2547 FAX: 886-2-2655-7379 E-Mail: Ronnie_cheng@sercomm.com
1 | SZ-BSW01-MPE Report | RF Exposure Info | 45.26 KiB | June 19 2013 |
Compliance Certification Services Inc. Report No.: T130522D04 Date of Issue: June 13, 2013 APPENDIX I RADIO FREQUENCY EXPOSURE LIMIT According to 15.247(i), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See 1.1307(b)(1) of this chapter. EUT Specification EUT ZigBee Binary Switch Frequency band
(Operating) ZigBee: 2.405GHz ~ 2.480GHz Others Device category Exposure classification Antenna Specification Portable (<20cm separation) Mobile (>20cm separation) Others Occupational/Controlled exposure (S = 5mW/cm2) General Population/Uncontrolled exposure
(S=1mW/cm2) PCB Antenna / Gain: -1.03 dBi, (Numeric gain: 0.79) Max. output power ZigBee: 17.48 dBm(55.98 mW) Evaluation applied MPE Evaluation*
SAR Evaluation N/A Remark:
The maximum output power is 17.48dBm (55.98mW) at 2405MHz (with 0.79 numeric antenna gain.) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 1 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04 Date of Issue: June 13, 2013 TEST RESULTS No non-compliance noted. Calculation Given
&
Where E = Field strength in Volts / meter P = Power in Watts G = Numeric antenna gain d = Distance in meters S = Power density in milliwatts / square centimeter Combining equations and re-arranging the terms to express the distance as a function of the remaining variables yields:
Changing to units of mW and cm, using:
Yields P (mW) = P (W) / 1000 and d (cm) = d(m) / 100 Equation 1 Where d = Distance in cm P = Power in mW G = Numeric antenna gain S = Power density in mW / cm2 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 2 Rev.00 dGPE303772ES237730dGPS220796.0100/3771000/30dGPdGPS Compliance Certification Services Inc. Report No.: T130522D04 Date of Issue: June 13, 2013 Maximum Permissible Exposure Substituting the MPE safe distance using d = 20 cm into Equation 1:
Where P = Power in mW G = Numeric antenna gain S = Power density in mW / cm2 IEEE 802.15.4 mode:
This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 3 Rev.00 GPS000199.0Ch.Frq.(MHz)P (mW)Gain (num.)D (cm)Power density in mW / cm2Limit (mW/cm2)1240555.980.79200.00881
1 | SZ-BSW01-Power of Attorney | Cover Letter(s) | 357.27 KiB | June 19 2013 |
SerComm Corporation Taipei Office: 8F, No.3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. TEL: 886-2-2655-3988 FAX: 886-2-2655-3966 Chu Nan Office: 3F, No. 81, YuYi Rd., Chu-Nan, Miao-Li 350, Taiwan, R.O.C. TEL: 886-37-585-899 FAX: 886-37-585-000 DateJune 5, 2013 BABT TCB Forsyth House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD Dear Sir or Madam, We, SerComm Corporation hereby authorize Compliance Certification Services Inc / Stan Lin . to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. This authorization expires on 2013/12/31 Your Sincerely, Ronnie Cheng Associate Manager / R&D Division SerComm Corporation TEL: 886-2-2655-3988#2547 FAX: 886-2-2655-7379 E-Mail: Ronnie_cheng@sercomm.com
1 | SZ-BSW01-Test Report | Test Report | 371.70 KiB | June 19 2013 |
Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 FCC 47 CFR PART 15 SUBPART C TEST REPORT For ZigBee Binary Switch Model: SZ-BSW01xxxxxxxx(x= 0~9, A~Z, Blank or any Character) Trade Name: SerComm Issued to 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. SerComm Corporation Issued by Compliance Certification Services Inc. No.81-1, Lane 210, Bade 2nd Rd., Lujhu Township, Taoyuan County 33841, Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 http://www.ccsrf.com service@ccsrf.com Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, A2LA, NIST or any government agencies. The test results in the report only apply to the tested sample. Page 1 / 45 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Rev. 00 Issue Date June 6, 2013 Revision History Revisions Effect Page Revised By Initial Issue ALL Landy Huang This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 2 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ...........................................................................................4 2. EUT DESCRIPTION................................................................................................................5 3. TEST METHODOLOGY..........................................................................................................6 3.1 EUT CONFIGURATION.....................................................................................................6 3.2 EUT EXERCISE.................................................................................................................6 3.3 GENERAL TEST PROCEDURES......................................................................................6 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ..........................................7 3.4 3.5 DESCRIPTION OF TEST MODES.....................................................................................7 4. INSTRUMENT CALIBRATION ...............................................................................................8 4.1 MEASURING INSTRUMENT CALIBRATION ....................................................................8 4.2 MEASUREMENT EQUIPMENT USED ..............................................................................8 4.3 MEASUREMENT UNCERTAINTY.....................................................................................9 5. FACILITIES AND ACCREDITATIONS.................................................................................10 FACILTIES.......................................................................................................................10 5.1 EQUIPMENT....................................................................................................................10 5.2 5.3 TABLE OF ACCREDITATIONS AND LISTINGS..............................................................11 6. SETUP OF EQUIPMENT UNDER TEST ..............................................................................12 SETUP CONFIGURATION OF EUT ................................................................................12 6.1 6.2 SUPPORT EQUIPMENT..................................................................................................12 7. FCC PART 15.247 REQUIREMENTS ..................................................................................13 6DB BANDWIDTH ............................................................................................................13 7.1 PEAK POWER .................................................................................................................16 7.2 AVERAGE POWER .........................................................................................................17 7.3 7.4 BAND EDGES MEASUREMENT.....................................................................................18 PEAK POWER SPECTRAL DENSITY.............................................................................23 7.5 SPURIOUS EMISSIONS..................................................................................................26 7.6 7.7 POWERLINE CONDUCTED EMISSIONS.......................................................................39 8. APPENDIX I PHOTOGRAPHS OF TEST SETUP................................................................42 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 3 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 1. TEST RESULT CERTIFICATION Applicant:
Manufacturer:
SerComm Corporation 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. SerComm Corporation 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. Equipment Under Test: ZigBee Binary Switch Trade Name:
Model:
Date of Test:
SerComm SZ-BSW01xxxxxxxx(x= 0~9, A~Z, Blank or any Character) May 28 ~ 29, 2013 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that:
The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.247. The test results of this report relate only to the tested sample EUT identified in this report. Approved by:
Stan Lin Section Manager Reviewced by:
Angel Hu Section Manager This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 4 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 2. EUT DESCRIPTION Product ZigBee Binary Switch Trade Name Model Number Model Discrepancy SerComm SZ-BSW01xxxxxxxx(x= 0~9, A~Z, Blank or any Character) 1. The mean of x (x= 0~9, A~Z, Blank or any Character) on model number just for marketing purpose only. 2. Client consigns only one model sample to test (model number: SZ-BSW01). Therefore, the testing Lab. just guarantees the unit, which has been tested. EUT Power Rating 120VDC, 50-60Hz RF Module Manufacturer ARM Model EM357 Operating Frequency Range 2405 ~ 2480MHz Transmit Power 17.51dBm (0.0564W) Modulation Technique OPQSK (Offset Quadrature Phase Shift Keyed) Number of Channels 16 Channels Antenna Specification Remark:
PCB Antenna / Gain: -1.03 dBi 1. The sample selected for test was production product and was provided by manufacturer. 2. This submittal(s) (test report) is intended for FCC ID: P27SZBSW01 filing to comply with Section 15.207, 15.209 and 15.247 of the FCC Part 15, Subpart C Rules. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 5 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4 and FCC CFR 47 Part 2, Part 15.207, 15.209 and 15.247. 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.207, 15.209 and 15.247 under the FCC Rules Part 15 Subpart C. 3.3 GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.4 Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 13.1.4.1 of ANSI C63.4. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 6 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS
(a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below:
MHz MHz 0.090 - 0.110 10.495 - 0.505 2.1735 - 2.1905 4.125 - 4.128 4.17725 - 4.17775 4.20725 - 4.20775 6.215 - 6.218 6.26775 - 6.26825 6.31175 - 6.31225 8.291 - 8.294 8.362 - 8.366 8.37625 - 8.38675 8.41425 - 8.41475 12.29 - 12.293 12.51975 - 12.52025 12.57675 - 12.57725 13.36 - 13.41 16.42 - 16.423 16.69475 - 16.69525 16.80425 - 16.80475 25.5 - 25.67 37.5 - 38.25 73 - 74.6 74.8 - 75.2 108 - 121.94 123 - 138 149.9 - 150.05 156.52475 -
156.52525 156.7 - 156.9 162.0125 - 167.17 167.72 - 173.2 240 - 285 322 - 335.4 MHz 399.9 - 410 608 - 614 960 - 1240 1300 - 1427 1435 - 1626.5 1645.5 - 1646.5 1660 - 1710 1718.8 - 1722.2 2200 - 2300 2310 - 2390 2483.5 - 2500 2655 - 2900 3260 - 3267 3332 - 3339 3345.8 - 3358 3600 - 4400 GHz 4.5 - 5.15 5.35 - 5.46 7.25 - 7.75 8.025 - 8.5 9.0 - 9.2 9.3 - 9.5 10.6 - 12.7 13.25 - 13.4 14.47 - 14.5 15.35 - 16.2 17.7 - 21.4 22.01 - 23.12 23.6 - 24.0 31.2 - 31.8 36.43 - 36.5
(2) 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6
(b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. 3.5 DESCRIPTION OF TEST MODES The EUT (model: SZ-BSW01) had been tested under operating condition. Test program used to control the EUT for staying in continuous transmitting mode was programmed. After verification, all tests were carried out with the worst case test modes as shown below except radiated spurious emission below 1GHz, which worst case was in transmitting mode only. Channel Low (2405MHz), Channel Mid (2445MHz) and Channel High (2480MHz) were chosen for the final testing. The field strength of spurious emission was measured in the following position: EUT stand-up position (Z axis), lie-down position (X, Y axis). The worst emission was found in stand-up position (X axis) and the worst case was recorded. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 7 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 4. INSTRUMENT CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement Conducted Emissions Test Site Name of Equipment Manufacturer Spectrum Analyzer Spectrum Analyzer Agilent Agilent Anritsu Anritsu Power meter Power Sensor Model E4446A N9010A ML2495A MA2411B Serial Number Calibration Due MY48250064 MY52220817 01/13/2014 02/22/2014 08/19/2013 08/19/2013 1033009 0917221 3M Semi Anechoic Chamber Name of Equipment Manufacturer Spectrum Analyzer Agilent Pre-Amplifier Pre-Amplifier Pre-Amplifier HP EMEC MITEQ EMI Test Receiver SCHAFFNER Model E4446A 8447D EM01M26G AMF-6F-26040 0-40-8P SCR 3501 6502 Loop Antenna Bilog Antenna Horn Antenna Horn Antenna Antenna Tower Turn Table Test S/W EMCO SCHWAZBECK VULB9160 EMCO EMCO CCS CCS 3115 3116 CC-A-1F CC-T-1F Serial Number Calibration Due MY48250064 2944A06530 060570 985646 430 2356 3084 9602-4659 00026370 N/A N/A 01/13/2014 01/02/2014 10/30/2013 05/19/2014 03/24/2014 06/11/2013 09/26/2013 06/14/2013 10/07/2013 N.C.R N.C.R EZ-EMC Powerline Conducted Emissions Test Site Name of Equipment Manufacturer EMI Test Receiver R&S R&S FCC TESEQ Model ESCI ENV216 FCC-LISN-50/2 50-16-2-07 ISN-T8 Serial Number Calibration Due 101338 101549 06012 34371 01/22/2014 12/04/2013 12/11/2013 03/03/2014 EZ_EMC LISN LISN ISN Test S/W NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. N.C.R = No Calibration Request. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 8 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 4.3 MEASUREMENT UNCERTAINTY Parameter Powerline Conducted Emission 3M Semi Anechoic Chamber / 30MHz ~ 1GHz 3M Semi Anechoic Chamber / Above 1GHz Uncertainty 0.7724 3.7046 3.0958 Remark: This uncertainty represents an expanded uncertainty expressed at approximately the 95%
confidence level using a coverage factor of k=2. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 9 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 5. FACILITIES AND ACCREDITATIONS 5.1 FACILTIES All measurement facilities used to collect the measurement data are located at No. 163-1, Jhongsheng Rd., Sindien District, Taipei City 23151, Taiwan Tel:
886-2-2217-0894 / Fax: 886-2-2217-1029 No 11, Wugong 6th Rd, Wugu District, New Taipei City 24891, Taiwan (R.O.C) Tel: 886-2-2299-9720 / Fax: 886-2-2298-4045 No.81-1, Lane 210, Bade 2nd Rd., Lujhu Township, Taoyuan County 33841,Taiwan, R.O.C. Tel: 886-3-324-0332 / Fax: 886-3-324-5235 The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, Radio Interference Measuring Apparatus and Measurement Methods. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 10 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 5.3 TABLE OF ACCREDITATIONS AND LISTINGS Country Agency Scope of Accreditation Logo USA A2LA CFR 47, FCC Part15/18, CISPR 22, EN 55022, ICES-003, AS/NZS CISPR 22, VCCI V-3, EN 55011, CISPR 11, IEC/EN 61000-4-2/3/4/5/6/8/11, EN 61000-6-1/2/3/4, EN 55024, CISPR 24, AS/NZS CISPR 24, AS/NZS 61000.6.2, EN 55014-1/-2, ETSI EN 300 386 v1.3.2/v1.3.3, IEC/EN 61000-3-2, AS/NZS 61000.3.2, IEC/EN 61000-3-3, AS/NZS 61000.3.3 USA FCC MRA 3/10 meter Open Area Test Sites to perform FCC Part 15/18 measurements TW1026 Japan VCCI 3/10 meter Open Area Test Sites and conducted test sites to perform radiated/conducted measurements R-2882/2541/2798/725/1868 C-402/747/912 T-1930/1646 Taiwan TAF EN 55014-1, CISPR 14, CNS 13781-1, EN 55013, CISPR 13, CNS 13439, EN 55011, CISPR 11, CNS 13803, PLMN09, IS2045-0, LP0002 FCC Part 27/90, Part 15B/C/D/E, RSS-192/193/210/310 ETSI EN 300 328/ 300 220-1/ 300 220-2/ 301 893/ 301 489-01/ 301 489-03/ 301 489-07 /
301 489-17/ 300 440-1/ 300 440-2 AS/NZS 4268, AS/NZS 4771 CISPR 22, EN 55022, CNS 13438, AS/NZS CISPR 22, VCCI, IEC/EN 61000-4-2/3/4/5/6/8/11, CNS 14676-2/3/4/5/6/8, CNS 14934-2/3, CNS 13783-1, CNS 13439, CNS 13803 Taiwan BSMI CNS 13438, CNS 13783-1, CNS 13439, CNS 14115 Canada Industry Canada RSS-Gen Issue 3 SL2-IS-E-0014 / IN-E-0014
/A1-E-0014 /R1-E-0014
/R2-E-0014 /L1-E-0014 IC 2324C-5 Note: No part of this report may be used to claim or imply product endorsement by A2LA, TAF or other government agency. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 11 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT For Conducted and Radiated (Above 1GHz) Emission Measurement:
No. Device Type Model Series No. FCC ID 1. Default Hostname ISA3 N/A N/A Brand ember 2 Notebook PC D400 0932RY E2K24GBRL DELL Data Cable Power Cord Unshielded, 0.3m LAN Cable:
Unshielded, 2.0m USB Cable:
Unshielded, 1.9m N/A I/P:
Unshielded, 1.8m O/P:
Unshielded, 1.0m For Powerline Conducted and Radiated (Below 1GHz) Emission measurement:
No. Device Type Model Series No. FCC ID Brand Data Cable Power Cord 1 Test Jig N/A N/A N/A N/A N/A Unshielded, 1.8m Remark: Grounding was established in accordance with the manufacturers requirements and conditions for the intended use. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 12 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 7. FCC PART 15.247 REQUIREMENTS 7.1 6dB BANDWIDTH LIMIT According to 15.247(a)(2), systems using digital modulation techniques may operate in the 902 - 928 MHz, 2400 - 2483.5 MHz, and 5725 - 5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. TEST CONFIGURATION EUT Spectrum Analyzer TEST PROCEDURE 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the spectrum analyzer as RBW = 100kHz, VBW = 300kHz, Span = 3MHz, Sweep
= auto. 4. Mark the peak frequency and 6dB (upper and lower) frequency. 5. Repeat until all the rest channels are investigated. TEST RESULTS No non-compliance noted TEST DATA Channel Low Mid High Frequency
(MHz) Bandwidth (MHz) 2405 2445 2480 1.610 1.625 1.640 Limit
(kHz)
>500 Result PASS PASS PASS This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 13 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Test Plot 6dB Bandwidth (CH Low) 6dB Bandwidth (CH Mid) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 14 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 6dB Bandwidth (CH High) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 15 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 7.2 PEAK POWER LIMIT The maximum peak output power of the intentional radiator shall not exceed the following:
1. According to 15.247(b)(3), for systems using digital modulation in the bands of 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz: 1 Watt. 2. According to 15.247(b)(4), the conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section, if transmitting antennas of directional gain greater than 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs
(b)(1), (b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the antenna exceeds 6 dBi. TEST CONFIGURATION EUT Power Meter TEST PROCEDURE Per KDB 558074 V02 The transmitter output is connected to the Power Meter. The Power Meter is set to the peak power detection. TEST RESULTS No non-compliance noted TEST DATA Channel Frequency
(MHz) Output Power
(dBm) Output Power
(W) Limit
(W) Low Mid High 2405 2445 2480 17.51 16.88
-2.47 0.0564 0.0488 0.0006 1 Result PASS PASS PASS This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 16 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 7.3 AVERAGE POWER LIMIT None; for reporting purposes only. TEST CONFIGURATION EUT Power Meter TEST PROCEDURE Per KDB 558074 V02 The transmitter output is connected to the Power Meter. The Power Meter is set to the peak power detection. TEST RESULTS No non-compliance noted TEST DATA Channel Low Mid High Frequency
(MHz) Output Power
(dBm) Output Power
(W) 2405 2445 2480 17.48 16.82
-3.14 0.0560 0.0481 0.0005 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 17 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 7.4 BAND EDGES MEASUREMENT LIMIT According to 15.247(d), in any 100 kHz bandwidth outside the frequency bands in which the spread spectrum intentional radiator in operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. In addition, radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see Section 15.205(c)). TEST CONFIGURATION Antenna tower EUT 3m 4m Horn antenna Spectrum analyzer Turntable 0.8m 1m 30cm Pre-amp TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above the ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. out the highest emission. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find 4. Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission:
(a) PEAK: RBW=VBW=1MHz / Sweep=100ms
(b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 5. Repeat the procedures until all the PEAK and AVERAGE versus POLARIZATION are measured. TEST RESULTS Refer to attach spectrum analyzer data chart. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 18 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Test Plot Band Edges (CH Low) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 19 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 20 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Band Edges (CH High) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 21 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 22 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 7.5 PEAK POWER SPECTRAL DENSITY LIMIT 1. According to 15.247(e), for digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. 2. According to 15.247(f), the digital modulation operation of the hybrid system, with the frequency hopping turned off, shall comply with the power density requirements of paragraph (d) of this section. TEST CONFIGURATION EUT Spectrum Analyzer TEST PROCEDURE Per KDB 558074 V02 1. Place the EUT on the table and set it in transmitting mode.Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 2. Set the spectrum analyzer as RBW = 3kHz, VBW = 10kHz, Span = 3MHz, Sweep=
auto. 3. Record the max. reading. 4. Repeat the above procedure until the measurements for all frequencies are completed. TEST RESULTS No non-compliance noted TEST DATA Channel Frequency
(MHz) Low Mid High 2405 2445 2480 PPSD
(dBm) 2.06 1.11
-18.63 Limit
(dBm) Result 8.00 PASS This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 23 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Test Plot PPSD (CH Low) PPSD (CH Mid) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 24 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 PPSD (CH High) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 25 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 7.6 SPURIOUS EMISSIONS 7.6.1 CONDUCTED MEASUREMENT LIMIT According to 15.247(d), in any 100 kHz bandwidth outside the frequency bands in which the spread spectrum intentional radiator in operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. In addition, radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see Section 15.205(c)). TEST CONFIGURATION EUT Spectrum Analyzer TEST PROCEDURE Conducted RF measurements of the transmitter output were made to confirm that the EUT antenna port conducted emissions meet the specified limit and to identify any spurious signals that require further investigation or measurements on the radiated emissions site. The transmitter output is connected to the spectrum analyzer. The resolution bandwidth is set to 100 kHz. The video bandwidth is set to 100 kHz. Measurements are made over the 30MHz to 26GHz range with the transmitter set to the lowest, middle, and highest channels. TEST RESULTS No non-compliance noted. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 26 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Test Plot Spurious Emissions CH Low CH Mid This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 27 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 CH High This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 28 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Conducted band-edge CH Low CH High This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 29 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 7.6.2 RADIATED EMISSIONS LIMIT 1. According to 15.209(a), except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table:
Frequency
(MHz) 30-88 88-216 216-960 Above 960 Field Strength
(V/m) 100*
150*
200*
500 Measurement Distance
(m) 3 3 3 3 Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 2. In the emission table above, the tighter limit applies at the band edges. Frequency
(MHz) 30-88 88-216 216-960 Above 960 Field Strength
(V/m at 3-meter) 100 150 200 500 Field Strength
(dBV/m at 3-meter) 40 43.5 46 54 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 30 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 TEST CONFIGURATION Below 1 GHz EUT 3m 4m Turntable 0.8m 1m Reference ground plane Above 1 GHz EUT 3m 4m Antenna tower Bi-log antenna Spectrum analyzer Antenna tower Horn antenna Spectrum analyzer Turntable 0.8m 1m 30cm Pre-amp This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 31 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as:
Below 30MHz RBW=10kHz / VBW=30kHz / Sweep=AUTO 30 ~ 1000MHz:
RBW=100kHz / VBW=300KHz / Sweep=AUTO Above 1GHz:
a) PEAK: RBW=VBW=1MHz / Sweep=AUTO b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. TEST RESULTS No non-compliance noted. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 32 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 TEST DATA Below 1GHz Operation Mode:
Temperature:
Humidity:
Transmitting 26C 56% RH Test Date:
Tested by:
Polarity:
May 29, 2013 Francis Lee Ver. / Hor. Frequency
(MHz) 40.6700 99.8400 132.8200 369.5000 577.0800 945.6800 54.2500 128.9400 159.9800 568.3500 800.1799 942.7700 Remark:
Reading
(dBuV) 34.80 31.60 28.80 25.00 25.40 26.00 34.40 34.80 30.80 25.70 26.30 25.00 Correction Factor
(dB/m)
-7.73 2.03 0.09
-7.72
-6.70
-4.42
-2.99
-2.83 3.21
-6.36
-8.79
-6.81 Result
(dBuV/m) 27.07 33.63 28.89 17.28 18.70 21.58 31.41 31.97 34.01 19.34 17.51 18.19 Limit
(dBuV/m) 40.00 43.50 43.50 46.00 46.00 46.00 40.00 43.50 43.50 46.00 46.00 46.00 Margin
(dB)
-12.93
-9.87
-14.61
-28.72
-27.30
-24.42
-8.59
-11.53
-9.49
-26.66
-28.49
-27.81 Ant. Pol.
(H/V) Remark V V V V V V H H H H H H QP QP QP QP QP QP QP QP QP QP QP QP 1. No emission found between lowest internal used / generated frequency to 30 MHz. (9kHz ~ 30MHz) 2. Measuring frequencies from 9 kHz to the 1GHz. 3. Radiated emissions measured in the measured frequency range were made with an instrument using peak detector or quasi-peak detector mode. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. The IF bandwidth of SPA between 30MHz to 1GHz was 100kHz. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 33 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Above 1 GHz Operation Mode:
Temperature:
Humidity:
Freq.
(MHz) 1992.000 2478.000 2478.000 2690.000 4810.000 4810.000 6130.000 7215.000 7215.000 9620.000 9620.000 12020.000 12020.000 14430.000 14430.000 Remark:
Reading
(dBuV) 52.42 53.51 41.51 53.37 54.15 45.26 38.10 50.02 40.96 40.95 32.66 47.42 36.66 46.22 36.88 TX / CH Low 26C 56 % RH Test Date:
Tested by:
Polarity:
May 28, 2013 Francis Lee Ver. / Hor. Correct Factor
(dB/m)
-1.43
-1.09
-1.09
-1.54 2.35 2.35 5.51 10.12 10.12 14.22 14.22 10.77 10.77 14.90 14.90 Result
(dBuV/m) 50.99 52.42 40.42 51.83 56.50 47.61 43.61 60.14 51.08 55.17 46.88 58.19 47.43 61.12 51.78 Limit
(dBuV/m) 74.00 74.00 54.00 74.00 74.00 54.00 74.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 Margin
(dB)
-23.01
-21.58
-13.58
-22.17
-17.50
-6.39
-30.39
-13.86
-2.92
-18.83
-7.12
-15.81
-6.57
-12.88
-2.22 Ant. Pol H/V V V V V V V V V V V V V V V V Remark peak peak AVG peak peak AVG peak peak AVG peak AVG peak AVG peak AVG 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 34 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Reading
(dBuV) 52.83 54.12 52.93 52.60 42.39 37.75 49.84 41.25 42.11 33.83 45.70 36.80 45.37 37.10 Correct Factor
(dB/m)
-6.50
-3.64
-3.36 5.62 5.62 8.88 10.69 10.69 14.44 14.44 10.78 10.78 14.90 14.90 Result
(dBuV/m) 46.33 50.48 49.57 58.22 48.01 46.63 60.53 51.94 56.55 48.27 56.48 47.58 60.27 52.00 Limit
(dBuV/m) 74.00 74.00 74.00 74.00 54.00 74.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 Margin
(dB)
-27.67
-23.52
-24.43
-15.78
-5.99
-27.37
-13.47
-2.06
-17.45
-5.73
-17.52
-6.42
-13.73
-2.00 Ant. Pol H/V H H H H H H H H H H H H H H Remark peak peak peak peak AVG peak peak AVG peak AVG peak AVG peak AVG Freq.
(MHz) 1826.000 2164.000 2616.000 4810.000 4810.000 5505.000 7215.000 7215.000 9620.000 9620.000 12030.000 12030.000 14430.000 14430.000 Remark:
1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 35 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Operation Mode:
Temperature:
Humidity:
Freq.
(MHz) 1986.000 2286.000 2286.000 2710.000 4890.000 4890.000 6480.000 7335.000 7335.000 9780.000 9780.000 12220.000 12220.000 14670.000 14670.000 Remark:
Reading
(dBuV) 53.05 54.41 40.69 53.49 57.14 48.57 37.48 46.87 36.31 47.32 39.19 48.19 40.14 46.78 38.10 TX / CH Mid 26C 56 % RH Test Date:
Tested by:
Polarity:
May 28, 2013 Francis Lee Ver. / Hor. Correct Factor
(dB/m)
-1.52
-1.52
-1.52
-1.53 4.15 4.15 6.91 10.77 10.77 13.82 13.82 10.88 10.88 14.27 14.27 Result
(dBuV/m) 51.53 52.89 39.17 51.96 61.29 52.72 44.39 57.64 47.08 61.14 53.01 59.07 51.02 61.05 52.37 Limit
(dBuV/m) 74.00 74.00 54.00 74.00 74.00 54.00 74.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 Margin
(dB)
-22.47
-21.11
-14.83
-22.04
-12.71
-1.28
-29.61
-16.36
-6.92
-12.86
-0.99
-14.93
-2.98
-12.95
-1.63 Ant. Pol H/V V V V V V V V V V V V V V V V Remark peak peak AVG peak peak AVG peak peak AVG peak AVG peak AVG peak AVG 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 36 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Reading
(dBuV) 52.98 53.23 53.49 53.61 44.59 37.66 47.99 39.22 40.20 33.45 46.12 38.88 44.80 36.27 Correct Factor
(dB/m)
-6.81
-3.63
-3.25 6.98 6.98 8.70 11.64 11.64 13.99 13.99 10.88 10.88 14.27 14.27 Result
(dBuV/m) 46.17 49.60 50.24 60.59 51.57 46.36 59.63 50.86 54.19 47.44 57.00 49.76 59.07 50.54 Limit
(dBuV/m) 74.00 74.00 74.00 74.00 54.00 74.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 Margin
(dB)
-27.83
-24.40
-23.76
-13.41
-2.43
-27.64
-14.37
-3.14
-19.81
-6.56
-17.00
-4.24
-14.93
-3.46 Ant. Pol H/V H H H H H H H H H H H H H H Remark peak peak peak peak AVG peak peak AVG peak AVG peak AVG peak AVG Freq.
(MHz) 1792.000 2168.000 2714.000 4890.000 4890.000 6090.000 7335.000 7335.000 9780.000 9780.000 12230.000 12230.000 14670.000 14670.000 Remark:
1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 37 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Operation Mode:
Temperature:
Humidity:
Freq.
(MHz) 1964.000 2252.000 2694.000 4080.000 5225.000 7090.000 1840.000 2166.000 2720.000 4330.000 5550.000 6935.000 Remark:
Reading
(dBuV) 53.53 53.06 53.35 39.08 38.39 37.53 53.43 53.12 53.01 39.43 38.14 38.21 TX / CH High 26C 56 % RH Test Date:
Tested by:
Polarity:
May 28, 2013 Francis Lee Ver. / Hor. Correct Factor
(dB/m)
-1.87
-1.44
-1.51 3.19 5.46 9.44
-6.37
-3.63
-3.19 7.44 9.03 9.21 Result
(dBuV/m) 51.66 51.62 51.84 42.27 43.85 46.97 47.06 49.49 49.82 46.87 47.17 47.42 Limit
(dBuV/m) 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 74.00 Margin
(dB)
-22.34
-22.38
-22.16
-31.73
-30.15
-27.03
-26.94
-24.51
-24.18
-27.13
-26.83
-26.58 Ant. Pol H/V V V V V V V H H H H H H Remark peak peak peak peak peak peak peak peak peak peak peak peak 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie:
margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 38 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 7.7 POWERLINE CONDUCTED EMISSIONS LIMIT According to 15.207(a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 H/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Frequency Range
(MHz) 0.15 to 0.50 Limits
(dBV) Quasi-peak 66 to 56*
0.50 to 5 5 to 30 56 60
* Decreases with the logarithm of the frequency. TEST CONFIGURATION Average 56 to 46*
46 50 See test photographs attached in Appendix II for the actual connections between EUT and support equipment. TEST PROCEDURE 1. The EUT was placed on a table, which is 0.8m above ground plane. 2. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 3. Repeat above procedures until all frequency measured were complete. TEST RESULTS The initial step in collecting conducted data is a spectrum analyzer peak scan of the measurement range. Significant peaks are then marked as shown on the following data page, and these signals are then quasi-peaked. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 39 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 TEST DATA Operation Mode:
Temperature:
Humidity:
Data Link 26C 60% RH Test Date: May 29, 2013 Tested by: Louis Shen Freq.
(MHz) QP Reading AV Reading Corr. factor QP Result 0.1556 0.1813 0.2009 0.2276 0.5896 0.6910 0.1762 0.2181 0.3071 0.3516 0.6490 0.7393 36.99 35.21 33.60 30.78 13.81 11.64 31.23 27.33 23.19 19.97 12.93 11.33 21.07 20.52 19.94 17.36 2.18 1.78 18.92 16.33 15.93 10.18 4.66 3.92 9.60 9.61 9.61 9.61 9.64 9.64 9.59 9.59 9.60 9.60 9.62 9.62 46.59 44.82 43.21 40.39 23.45 21.28 40.82 36.92 32.79 29.57 22.55 20.95 AV Result QP Limit AV Limit QP Margin
-19.10 30.67
-19.60 30.13 29.55
-20.36
-22.14 26.97 11.82
-32.55
-34.72 11.42 55.70 54.43 53.57 52.54 46.00 46.00 65.69 64.42 63.57 62.53 56.00 56.00 28.51 25.92 25.53 19.78 14.28 13.54 64.66 62.89 60.05 58.92 56.00 56.00 54.66 52.89 50.05 48.92 46.00 46.00
-23.84
-25.97
-27.26
-29.35
-33.45
-35.05 AV Margin Note
-25.03
-24.30
-24.02
-25.57
-34.18
-34.58
-26.15
-26.97
-24.52
-29.14
-31.72
-32.46 L1 L1 L1 L1 L1 L1 L2 L2 L2 L2 L2 L2 Remark:
1. The measuring frequencies range between 0.15 MHz and 30 MHz. 2. The emissions measured in the frequency range between 0.15 MHz and 30MHz were made with an instrument using Quasi-peak detector and Average detector. 3. The IF bandwidth of SPA between 0.15MHz and 30MHz was 10kHz. The IF bandwidth of Test Receiver between 0.15MHz and 30MHz was 9kHz. 4. L1 = Line One (Live Line) / L2 = Line Two (Neutral Line) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 40 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Test Plot Conducted emissions (Line 1) Conducted emissions (Line 2) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 41 Rev.00
1 | SZ-BSW01-Test Setup Photo | Test Setup Photos | 409.47 KiB | June 19 2013 |
Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 8. APPENDIX I PHOTOGRAPHS OF TEST SETUP Radiated Emission Set up Photos Below 1GHz This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 42 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Above 1GHz This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 43 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Conducted Emission Setup Photos This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 44 Rev.00 Compliance Certification Services Inc. Report No.: T130522D04-RP1 FCC ID: P27SZBSW01 Date of Issue: June 6, 2013 Powerline Conducted Emissions Setup Photos This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 45 Rev.00
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2013-06-19 | 2405 ~ 2480 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2013-06-19
|
||||
1 | Applicant's complete, legal business name |
Sercomm Corporation
|
||||
1 | FCC Registration Number (FRN) |
0015548027
|
||||
1 | Physical Address |
8F, No. 3-1, YuanQu St, NanKang
|
||||
1 |
Taipei, N/A
|
|||||
1 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
n******@babt.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
P27
|
||||
1 | Equipment Product Code |
SZBSW01
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
N**** W******
|
||||
1 | Title |
Engineer
|
||||
1 | Telephone Number |
886-2******** Extension:
|
||||
1 | Fax Number |
886-2********
|
||||
1 |
N******@SERCOMM.COM
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | ZigBee Binary Switch | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power is conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operated in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter RF Exposure procedures. End users must be informed of the requirements for satisfying RF Exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Compliance Certification Services Inc.
|
||||
1 | Name |
K**** C******
|
||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
k******@ccsrf.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2405.00000000 | 2480.00000000 | 0.0564000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC