all | frequencies |
|
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|---|
manual | photos | label |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User guide | Users Manual | 392.74 KiB | July 24 2012 | |||
1 |
|
Internal photos | Internal Photos | 476.51 KiB | July 24 2012 | |||
1 |
|
External photos | External Photos | 135.28 KiB | July 24 2012 | |||
1 |
|
External photos 2 | External Photos | 309.54 KiB | July 24 2012 | |||
1 |
|
Label and location | ID Label/Location Info | 3.39 MiB | July 24 2012 | |||
1 | Antenna spec. | Operational Description | July 24 2012 | confidential | ||||
1 | Block diagram | Block Diagram | July 24 2012 | confidential | ||||
1 |
|
Confidentiality letter | Cover Letter(s) | 357.69 KiB | July 24 2012 | |||
1 | Schematic | Schematics | July 24 2012 | confidential | ||||
1 |
|
Test Setup Photos | Test Setup Photos | 307.61 KiB | July 24 2012 | |||
1 |
|
Test report | Test Report | 938.37 KiB | July 24 2012 | |||
1 | Theory of operation | Operational Description | July 24 2012 | confidential |
1 | User guide | Users Manual | 392.74 KiB | July 24 2012 |
SZ-DWS02 ZigBee Door / Window Sensor User Guide Table of Contents CHAPTER 1 INTRODUCTION...................................................................................... 1 Package Contents ................................................................................................ 1 Specfication ..........................................................................!
CHAPTER 2 DEVICE DESCRIPTION .......................................................................... 2 Components.......................................................................................................... 2 Installation Guide ................................................................................................. 3 Preparing the Sensor for Installation ................................................................. 6 Operation............................................................................................................... 7 CHAPTER 3 REGULATORY APPROVAL................................................................... 8 Copyright Document Version: 1.0 All trademarks and trade names are the properties of their respective owners. 201 2. All Rights Reserved. i Chapter 1 Introduction 1 This Chapter provides an overview of the ZigBee Door/Window Sensor features and capabilities. Congratulations on the purchase of your new ZigBee Door/Window Sensor. The ZigBee Door/Window Sensor is a consumer electronic device, which is used for home monitoring and security. Package Contents SZ-DWS02 sensor The following items should be included:
Magnet If any of the above items are damaged or missing, please contact your dealer imme-
diately. Adhesive Tape x 2 pcs for Magnet / Sensor CR123A Lithium Battery x 1 pcs Screws x 4 pcs for magnet / sensor Installation & Operation Manual 1 pcs Specification Frequency: 2.4GHz Battery type: DC 3V, CR123A Lithium Battery Magnet gap: 1.27 cm ( 0.5 ) Supervisory interval: 60 mins Low Battery detection: under DC2.7V Operating temperature: 0 - 50C (32 - 122F);
Storage temperature: -20 - 70C (-4 - 158F) Dimensions :
Main Unit : 23 mm x 24 mm x 95 mm (0.91" x 0.94" x 3.74") Magnet Unit : 31 mm x 13 mm x 18 mm (1.22" x 0.51" x 0.71") 1 Chapter 2 Device Description 2 This Chapter provides device description for the ZigBee Door/Window Sensor. Components 2 Installation Guide Main Body:
3 Magnet:
4 The mgnet shall be fixed to close to the specific area, and the distance from sensor shall not be over 1.27cm (0.5 inch) 5 Preparing the Sensor for Installation The Sensor & Magnet contact can be mounted vertically or horizontally but note that the Magnet contact must be aligned (on the same side) as the alignment marks on the Sensor. 6 Operation 1. Normal operation, the LED will not light. 2. The sensor equipped with tamper switch. If the cover of sensor is removed, the door sensor will send an alarm report to the ZigBee interface controller. Before replacing the cover, the sensor is under Awake mode 3. For Join a network Put the ZigBee interface controller into Join mode, and following its instruction to add the sensor to controller. Join Press < 1 seconds and then start to "Join" processing While "presee < 1 seconds" , the LED is static on While running "joint" process, the LED is blinking Associate Duration Max >3 seconds for "Join" processing If joint succesfully, the Green LED will be on 2 seconds and then off If joint failed, the Green LED will be off directly. Leave Press 10 seconds and then run "Leave" processing 7 3 Chapter 3 REGULATORY APPROVAL FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement You are cautioned that changes or modifications not expressly approved by the party responsi-
ble for compliance could void your authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause undesired operation 8 CE Approval CE Standards This product complies with the 99/5/EEC directives, including the following safety and EMC standards:
EN300328-2 EN301489-1/-17 EN60950 CE Marking Warning This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 9
1 | Internal photos | Internal Photos | 476.51 KiB | July 24 2012 |
INTERNAL PHOTOGRAPHS OF EUT Report No: T120628D02 Page 2 Rev.00 Report No: T120628D02 Page 3 Rev.00 Report No: T120628D02 Antenna Page 4 Rev.00
1 | External photos | External Photos | 135.28 KiB | July 24 2012 |
EXTERNAL PHOTOGRAPHS OF EUT Report No: T120628D02 Page 1 / 4 Rev.00
1 | External photos 2 | External Photos | 309.54 KiB | July 24 2012 |
Chapter 2 Device Description 2 This Chapter provides device description for the ZigBee Door/Window Sensor. Components 2 Installation Guide Main Body:
3 Magnet:
4 The mgnet shall be fixed to close to the specific area, and the distance from sensor shall not be over 1.27cm (0.5 inch) 5 Preparing the Sensor for Installation The Sensor & Magnet contact can be mounted vertically or horizontally but note that the Magnet contact must be aligned (on the same side) as the alignment marks on the Sensor. 6
1 | Confidentiality letter | Cover Letter(s) | 357.69 KiB | July 24 2012 |
SerComm Corporation Taipei Office: 8F, No.3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. TEL: 886-2-2655-3988 FAX: 886-2-2655-3966 Chu Nan Office: 3F, No. 81, YuYi Rd., Chu-Nan, Miao-Li 350, Taiwan, R.O.C. TEL: 886-37-585-899 FAX: 886-37-585-000 DateJuly 17, 2012 BABT TCB Forsyth House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD Confidentiality Request FCC ID: P27SZDWS02 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules, SerComm Corporation hereby requests permanent confidential treatment of information accompanying this application as outlined below:
Common exhibits for which confidentiality is requested are:
Schematics Block Diagrams Theory of Operation The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Your Sincerely, Ronnie Cheng Associate Manager / R&D Division SerComm Corporation TEL: 886-2-2655-3988#2547 FAX: 886-2-2655-7379 E-Mail: Ronnie_cheng@sercomm.com
1 | Test Setup Photos | Test Setup Photos | 307.61 KiB | July 24 2012 |
Report No: T120628D02-RP1 FCC ID: P27SZDWS02 8. APPENDIX 1 PHOTOGRAPHS OF TEST SETUP Radiated Emission Set up Photos Below 1GHz Date of Issue: July 17, 2012 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 30 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 Above 1GHz Date of Issue: July 17, 2012 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 31 Rev.00
1 | Test report | Test Report | 938.37 KiB | July 24 2012 |
Report No: T120628D02-RP1 FCC ID: P27SZDWS02 FCC 47 CFR PART 15 Subpart C Date of Issue: July 17, 2012 TEST REPORT For ZigBee Door Windows Sensor Model SZ-DWS02xxxxxxxx (x = 0~9, A~Z, Blank or any Character) Trade Name: SerComm Issued to 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. SerComm Corporation Issued by Compliance Certification Services Inc. No.81-1, Lane 210, Bade 2nd Rd., Lujhu Township, Taoyuan County 33841,Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 http://www.ccsrf.com service@ccsrf.com Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, A2LA, NIST or any government agencies. The test results in the report only apply to the tested sample. Page 1 / 31 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 Date of Issue: July 17, 2012 Revision History Revisions Initial Issue Effect Page ALL Revised By Jill Shiau Issue Date July 17, 2012 Rev. 00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 2 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 TABLE OF CONTENTS Date of Issue: July 17, 2012 1. TEST RESULT CERTIFICATION..................................................................................... 4 2. EUT DESCRIPTION ......................................................................................................... 5 3. TEST METHODOLOGY ................................................................................................... 6 3.1 EUT CONFIGURATION............................................................................................... 6 3.2 EUT EXERCISE........................................................................................................... 6 3.3 GENERAL TEST PROCEDURES ............................................................................... 6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS .................................... 7 3.5 DESCRIPTION OF TEST MODES .............................................................................. 7 4. INSTRUMENT CALIBRATION......................................................................................... 8 4.1 MEASURING INSTRUMENT CALIBRATION.............................................................. 8 4.2 MEASUREMENT EQUIPMENT USED........................................................................ 8 4.3 MEASUREMENT UNCERTAINTY .............................................................................. 9 5. FACILITIES AND ACCREDITATIONS........................................................................... 10 5.1 FACILITIES................................................................................................................ 10 5.2 EQUIPMENT ............................................................................................................. 10 5.3 TABLE OF ACCREDITATIONS AND LISTINGS ....................................................... 11 6. SETUP OF EQUIPMENT UNDER TEST........................................................................ 12 6.1 SETUP CONFIGURATION OF EUT .......................................................................... 12 6.2 SUPPORT EQUIPMENT ........................................................................................... 12 7. FCC PART 15.249 REQUIREMENTS............................................................................ 13 7.1 20DB BANDWIDTH.................................................................................................... 13 7.2 BAND EDGES MEASUREMENT............................................................................... 16 7.3 SPURIOUS EMISSION.............................................................................................. 21 7.4 POWERLINE CONDUCTED EMISSIONS................................................................. 28 8. APPENDIX 1 PHOTOGRAPHS OF TEST SETUP ........................................................ 30 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 3 Rev.00 Date of Issue: July 17, 2012 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 1. TEST RESULT CERTIFICATION Applicant:
Manufacturer:
SerComm Corporation 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. SerComm Corporation 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan, R.O.C. Equipment Under Test: ZigBee Door Windows Sensor Trade Name:
Model:
Date of Test:
SerComm SZ-DWS02xxxxxxxx (x = 0~9, A~Z, Blank or any Character) July 12 ~ 13, 2012 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that:
The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements emission limits of FCC Rules Part 15.207, 15.209 and 15.249. The test results of this report relate only to the tested sample identified in this report. Approved by:
Stan Lin Section Manager Reviewed by:
Jill Shiau Section Manager This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 4 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 2. EUT DESCRIPTION Date of Issue: July 17, 2012 Product Model Brand Model Discrepancy ZigBee Door Windows Sensor SZ-DWS02xxxxxxxx (x = 0~9, A~Z, Blank or any Character) SerComm 1. The mean of xxxxxxxx (x = 0~9, A~Z, Blank or any Character) on model number, just for marketing purpose only 2. Client consigns only one sample to test (model number:
SZ-DWS02). Therefore, the testing Lab. just guarantees the unit, which has been tested. EUT Power Rating 3VDC from Battery Operating Frequency Range 2405 ~ 2480MHz Output Power 93.32dBuV/m Modulation Technique OPQSK (Offset Quadrature Phase Shift Keyed) Number of Channels 16 Channels Antenna Designation PCB Antenna / Gain: 3.16dBi Remark:
1. The sample selected for test was production product and was provided by manufacturer. 2. This test report is intended for FCC ID: P27SZDWS02 to comply with Section 15.207, 15.209, 15.249 (FCC Part 15, Subpart C Rules.) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 5 Rev.00 Date of Issue: July 17, 2012 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4 (2009) and FCC CFR 47 Part 2, Part 15.207, 15.209 and 15.249. 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.207, 15.209, 15.249 under the FCC Rules Part 15 Subpart C. 3.3 GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.4 (2009) Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 13.1.4.1 of ANSI C63.4 (2009). This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 6 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS Date of Issue: July 17, 2012
(a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below:
MHz MHz 0.090 - 0.110 10.495 - 0.505 2.1735 - 2.1905 4.125 - 4.128 4.17725 - 4.17775 4.20725 - 4.20775 6.215 - 6.218 6.26775 - 6.26825 6.31175 - 6.31225 8.291 - 8.294 8.362 - 8.366 8.37625 - 8.38675 8.41425 - 8.41475 12.29 - 12.293 12.51975 - 12.52025 12.57675 - 12.57725 13.36 - 13.41 16.42 - 16.423 16.69475 - 16.69525 16.80425 - 16.80475 25.5 - 25.67 37.5 - 38.25 73 - 74.6 74.8 - 75.2 108 - 121.94 123 - 138 149.9 - 150.05 156.52475 -
156.52525 156.7 - 156.9 162.0125 - 167.17 167.72 - 173.2 240 - 285 322 - 335.4 MHz 399.9 - 410 608 - 614 960 - 1240 1300 - 1427 1435 - 1626.5 1645.5 - 1646.5 1660 - 1710 1718.8 - 1722.2 2200 - 2300 2310 - 2390 2483.5 - 2500 2655 - 2900 3260 - 3267 3332 - 3339 3345.8 - 3358 3600 - 4400 GHz 4.5 - 5.15 5.35 - 5.46 7.25 - 7.75 8.025 - 8.5 9.0 - 9.2 9.3 - 9.5 10.6 - 12.7 13.25 - 13.4 14.47 - 14.5 15.35 - 16.2 17.7 - 21.4 22.01 - 23.12 23.6 - 24.0 31.2 - 31.8 36.43 - 36.5
(2) 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6
(b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. 3.5 DESCRIPTION OF TEST MODES The EUT (model: SZ-DWS02) had been tested under operating condition. Test program used to control the EUT for staying in continuous transmitting mode was programmed. After verification, all tests were carried out with the worst case test modes as shown below except radiated spurious emission below 1GHz, which worst case was in transmitting mode only. The field strength of spurious emission was measured in the following position: EUT stand-up position (Z axis), lie-down position (X, Y axis). The worst emission was found in lie-down position (X axis) and the worst case was recorded. Channel Low (2405MHz), Channel Mid (2445MHz) and Channel High (2480MHz) were chosen for the final testing. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 7 Rev.00 Date of Issue: July 17, 2012 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 4. INSTRUMENT CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement Remark: Each piece of equipment is scheduled for calibration once a year. Conducted Emission Test Site Name of Equipment Manufacturer Spectrum Analyzer Spectrum Analyzer Agilent R&S Anritsu Anritsu Model E4446A FSEB ML2495A MA2411B Serial Number Calibration Due MY48250064 825829/011 1033009 0917221 12/25/2012 12/18/2012 08/18/2012 08/18/2012 Power meter Power Sensor 3M Semi Anechoic Chamber Name of Equipment Manufacturer Spectrum Analyzer Agilent Pre-Amplifier Pre-Amplifier Pre-Amplifier HP HP MITEQ EMI Test Receiver SCHAFFNER Model E4446A 8447D 8449B AMF-6F-26040 0-40-8P SCR 3501 Loop Antenna Bilog Antenna Horn Antenna Horn Antenna Antenna Tower Turn Table Test S/W EMCO 6502 SCHWAZBECK VULB9160 EMCO EMCO CCS CCS 3115 3116 CC-A-1F CC-T-1F Serial Number Calibration Due MY48250064 2944A06530 3008A01738 12/25/2012 01/03/2013 04/17/2013 05/20/2013 01/11/2013 06/11/2013 10/03/2012 06/14/2013 10/04/2012 N.C.R N.C.R 985646 430 2356 3084 9602-4659 00026370 N/A N/A LabVIEW 6.1 (Wugu Chamber EMI Teat V1_4.5.3) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 8 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 4.3 MEASUREMENT UNCERTAINTY Date of Issue: July 17, 2012 Parameter Powerline Conducted Emission 3M Semi Anechoic Chamber / 30MHz ~ 1GHz 3M Semi Anechoic Chamber / Above 1GHz Uncertainty N/A 4.0474 3.8967 Remark: This uncertainty represents an expanded uncertainty expressed at approximately the 95%
confidence level using a coverage factor of k=2. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 9 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at Date of Issue: July 17, 2012 No. 199, Chunghsen Road, Hsintien City, Taipei Hsien, Taiwan, R.O.C. Tel: 886-2-2217-0894 / Fax: 886-2-2217-1029 No.11, Wugong 6th Rd., Wugu Industrial Park, Taipei Hsien 248, Taiwan Tel: 886-2-2299-9720 / Fax: 886-2-2298-4045 No.81-1, Lane 210, Bade 2nd Rd., Lujhu Township, Taoyuan County 33841,Taiwan, R.O.C. Tel: 886-3-324-0332 / Fax: 886-3-324-5235 The sites are constructed in conformance with the requirements of ANSI C63.7 (1992), ANSI C63.4 (2009) and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, Radio Interference Measuring Apparatus and Measurement Methods. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 10 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 5.3 TABLE OF ACCREDITATIONS AND LISTINGS Country Agency Scope of Accreditation Date of Issue: July 17, 2012 Logo USA A2LA CFR 47, FCC Part15/18, CISPR 22, EN 55022, ICES-003, AS/NZS CISPR 22, VCCI V-3, EN 55011, CISPR 11, IEC/EN 61000-4-2/3/4/5/6/8/11, EN 61000-6-1/2/3/4, EN 55024, CISPR 24, AS/NZS CISPR 24, AS/NZS 61000.6.2, EN 55014-1/-2, ETSI EN 300 386 v1.3.2/v1.3.3, IEC/EN 61000-3-2, AS/NZS 61000.3.2, IEC/EN 61000-3-3, AS/NZS 61000.3.3 USA FCC MRA 3/10 meter Open Area Test Sites to perform FCC Part 15/18 measurements TW1026 Japan VCCI 3/10 meter Open Area Test Sites and conducted test sites to perform radiated/conducted measurements R-2882/2541/2798/725/1868 C-402/747/912 T-1930/1646 Taiwan TAF EN 55014-1, CISPR 14, CNS 13781-1, EN 55013, CISPR 13, CNS 13439, EN 55011, CISPR 11, CNS 13803, PLMN09, IS2045-0, LP0002 FCC Part 27/90, Part 15B/C/D/E, RSS-192/193/210/310 ETSI EN 300 328/ 300 220-1/ 300 220-2/ 301 893/ 301 489-01/ 301 489-03/ 301 489-07 /
301 489-17/ 300 440-1/ 300 440-2 AS/NZS 4268, AS/NZS 4771 CISPR 22, EN 55022, CNS 13438, AS/NZS CISPR 22, VCCI, IEC/EN 61000-4-2/3/4/5/6/8/11, CNS 14676-2/3/4/5/6/8, CNS 14934-2/3, CNS 13783-1, CNS 13439, CNS 13803 Taiwan BSMI CNS 13438, CNS 13783-1, CNS 13439, CNS 14115 Canada Industry Canada RSS-Gen Issue 3 SL2-IS-E-0014 / IN-E-0014
/A1-E-0014 /R1-E-0014
/R2-E-0014 /L1-E-0014 IC 2324C-5 Note: No part of this report may be used to claim or imply product endorsement by A2LA, TAF or other government agency. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 11 Rev.00 Date of Issue: July 17, 2012 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT Model No. Device Type Power Cord Data Cable Series No. FCC ID Brand N/A
**No any support equipment during the test. Remark: Grounding was established in accordance with the manufacturers requirements and conditions for the intended use. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 12 Rev.00 Date of Issue: July 17, 2012 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 7. FCC PART 15.249 REQUIREMENTS 7.1 20dB BANDWIDTH LIMIT None; for reporting purposes only. TEST CONFIGURATION TEST PROCEDURE 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the Spectrum Analyzer EUT antenna port to the spectrum analyzer. 3. Set the spectrum analyzer as RBW=100 kHz, VBW = 300 kHz, Span = 3MHz, Sweep = auto. 4. Mark the peak frequency and 20dB (upper and lower) frequency. 5. Repeat until all the rest channels are investigated. TEST RESULTS No non-compliance noted This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 13 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 TEST PLOT 20dB Bandwidth (CH Low) Date of Issue: July 17, 2012 20dB Bandwidth (CH Mid) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 14 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 20dB Bandwidth (CH High) Date of Issue: July 17, 2012 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 15 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 7.2 BAND EDGES MEASUREMENT LIMIT 1. In the above emission table, the tighter limit applies at the band edges. Date of Issue: July 17, 2012 Frequency
(MHz) 30-88 88-216 216-960 Above 960 Field Strength
(V/m at 3-meter) 100 150 200 500 Field Strength
(dBV/m at 3-meter) 40 43.5 46 54 2. As shown in Section 15.35(b), for frequencies above 1000 MHz, the above field strength limits in paragraphs (a) and (b) of this section are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. For point-to-point operation under paragraph (b) of this section, the peak field strength shall not exceed 2500 millivolts/meter at 3 meters along the antenna azimuth. TEST CONFIGURATION EUT 3m 4m Antenna tower Horn antenna Spectrum analyzer Turntable 0.8m 1m 30cm Pre-amp TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above the ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the level. highest emission. 4. Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission:
(a) PEAK: RBW=VBW=1MHz / Sweep=AUTO
(b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 5. Repeat the procedures until all the PEAK and AVERAGE versus POLARIZATION are measured. TEST RESULTS Refer to attach spectrum analyzer data chart. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 16 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 TEST PLOT Band Edges (CH Low) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical Date of Issue: July 17, 2012 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 17 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal Date of Issue: July 17, 2012 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 18 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 Band Edges (CH High) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical Date of Issue: July 17, 2012 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 19 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal Date of Issue: July 17, 2012 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 20 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 Date of Issue: July 17, 2012 7.3 SPURIOUS EMISSION LIMIT 1. In the section 15.249(a):
Except as provided in paragraph (b) of this section, the field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following:
Fundamental Frequency
(MHz) 902-928 MHz 2400 - 2483.5 MHz 5725 - 5875 MHz 24.0 - 24.25 GHz Field Strength of Fundamental Field Strength
(mV/m) 50 50 50 250 Field Strength of Harmonics
(V/m) 500 500 500 2500 2. Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table:
Field Strength Measurement Distance Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 3. In the above emission table, the tighter limit applies at the band edges. Field Strength
(V/m at 3-meter) Field Strength
(dBV/m at 3-meter)
(V/m) 100*
150*
200*
500
(m) 3 3 3 3 100 150 200 500 40 43.5 46 54 Frequency
(MHz) 30-88 88-216 216-960 Above 960 Frequency
(MHz) 30-88 88-216 216-960 Above 960 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 21 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 Date of Issue: July 17, 2012 TEST CONFIGURATION Below 1 GHz EUT 3m 4m Turntable 0.8m 1m Reference ground plane Above 1 GHz EUT 3m 4m Turntable 0.8m 1m 30cm Pre-amp Antenna tower Bi-log antenna Spectrum analyzer Antenna tower Horn antenna Spectrum analyzer This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 22 Rev.00 Date of Issue: July 17, 2012 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find 4. Maximum procedure was performed on the six highest emissions to ensure EUT emission level. out the highest emissions. compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as:
Below 30MHz RBW=9kHz / VBW=300kHz / Sweep=AUTO 30 ~ 1000MHz:
RBW=120kHz / VBW=3MHz / Sweep=AUTO Above 1GHz:
a). PEAK: RBW=VBW=1MHz / Sweep=AUTO b). AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. TEST RESULTS No non-compliance noted. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 23 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 Date of Issue: July 17, 2012 TEST DATA Below 1 GHz Operation Mode:
Temperature:
Humidity:
Frequency Reading
(dBuV)
(MHz) 205.0850 272.9849 442.2500 572.2300 624.1250 874.8700 205.0850 357.8599 496.0849 649.8300 722.0949 874.8700 Remark:
41.42 41.34 39.32 38.01 36.05 34.71 44.11 39.74 37.58 34.10 33.08 35.49 Transmitting 22C 57% RH Test Date:
Tested by:
Polarity:
July 12, 2012 Clark Su Ver. / Hor. Correction Factor
(dB/m)
-14.33
-11.33
-7.64
-5.49
-4.48
-0.26
-14.33
-10.30
-6.89
-3.96
-2.88
-0.26 Result
(dBuV/m) Limit
(dBuV/m) Margin
(dB) 27.09 30.01 31.68 32.52 31.57 34.45 29.78 29.44 30.69 30.14 30.20 35.23 43.50 46.00 46.00 46.00 46.00 46.00 43.50 46.00 46.00 46.00 46.00 46.00
-16.41
-15.99
-14.32
-13.48
-14.43
-11.55
-13.72
-16.56
-15.31
-15.86
-15.80
-10.77 Ant.Pol.
(H/V) Remark QP V V QP QP V QP V V QP QP V H H H H H H QP QP QP QP QP QP 1. No emission found between lowest internal used / generated frequency to 30 MHz.
(9kHz ~ 30MHz) 2. Measuring frequencies from 9 kHz to the 1GHz. 3. Radiated emissions measured in the measured frequency range were made with an instrument using Quasi-peak detector mode. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. The IF bandwidth of SPA between 30MHz to 1GHz was 100kHz. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 24 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 Date of Issue: July 17, 2012 Above 1 GHz Operation Mode:
Temperature:
Humidity:
Tx / CH Low 22C 57% RH Freq.
(MHz) Ant. Pol H/V Peak Reading
(dBuV) AV Reading
(dBuV) Ant. / CL CF
(dB) 2405.57 1978.000 2898.000 4810.000 N/A V V V V 76.98 49.22 48.53 45.04 2405.43 H 2200.000 H 2624.000 H 4810.000 H 92.40 49.88 49.06 47.49 N/A
---
---
---
---
---
---
---
38.78
-1.63
-1.65
-0.69 2.35
-6.21
-3.56
-3.36 5.62 Remark:
frequency. Test Date:
Tested by:
Polarity:
Result Peak
(dBuV/m) 75.35 47.57 47.84 47.39 AV
(dBuV/m)
---
---
---
---
July 12, 2012 Clark Su Ver. / Hor. Peak Limit
(dBuV/m) AV Limit
(dBuV/m) Margin
(dB) Remark 114.00 94.00
-18.65 Peak 74.00 74.00 74.00 54.00 54.00 54.00
-26.43 Peak
-26.16 Peak
-26.61 Peak 86.19 46.32 45.70 53.11
---
114.00
---
---
44.40 74.00 74.00 74.00 94.00 54.00 54.00 54.00
-7.81 Peak
-27.68 Peak
-28.30 Peak
-9.60 AVG 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown
--- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, N/A no emission measured remark, if no specific emissions from the EUT are with recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 25 Rev.00 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 Date of Issue: July 17, 2012 Operation Mode:
Temperature:
Humidity:
Tx / CH Mid 22C 57% RH Freq.
(MHz) Ant. Pol H/V Peak Reading
(dBuV) AV Reading
(dBuV) Ant. / CL CF
(dB) 2445.48 1960.000 2520.000 4890.000 N/A V V V V 74.97 49.16 49.46 41.95 2444.52 H 2120.000 H 2840.000 H 4890.000 H 92.29 49.18 48.41 44.68 N/A
---
---
---
---
---
---
---
---
-1.33
-1.93
-1.18 4.15
-5.22
-3.74
-2.18 6.98 Remark:
frequency. Test Date:
Tested by:
Polarity:
Result Peak
(dBuV/m) 73.64 47.23 48.28 46.10 87.07 45.44 46.23 51.66 AV
(dBuV/m)
---
---
---
---
---
---
---
---
July 12, 2012 Clark Su Ver. / Hor. Peak Limit
(dBuV/m) AV Limit
(dBuV/m) Margin
(dB) Remark 114.00 94.00
-20.36 Peak 74.00 74.00 74.00 54.00 54.00 54.00
-26.77 Peak
-25.72 Peak
-27.90 Peak 114.00 74.00 74.00 74.00 94.00 54.00 54.00 54.00
-6.93 Peak
-28.56 Peak
-27.77 Peak
-22.34 Peak 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown
--- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, N/A no emission measured remark, if no specific emissions from the EUT are with recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 26 Rev.00 Date of Issue: July 17, 2012 July 12, 2012 Clark Su Ver. / Hor. Report No: T120628D02-RP1 FCC ID: P27SZDWS02 Operation Mode:
Temperature:
Humidity:
Tx / CH High 22C 57% RH Test Date:
Tested by:
Polarity:
Result Freq.
(MHz) Ant. Pol H/V Peak Reading
(dBuV) AV Reading
(dBuV) Ant. / CL CF
(dB) 2479.47 2002.000 2924.000 N/A V V V 65.60 49.79 48.23
---
---
---
2479.50 H 2128.000 H 2826.000 H 4960.000 H 94.84 49.26 48.95 40.30 N/A 94.08
---
---
---
-1.08
-1.35
-0.81
-1.52
-3.72
-2.29 7.41 Peak
(dBuV/m) 64.52 48.44 47.42 93.32 45.54 46.66 47.71 AV
(dBuV/m)
---
---
---
Peak Limit
(dBuV/m) AV Limit
(dBuV/m) Margin
(dB) Remark 114.00 94.00
-29.48 AVG 74.00 74.00 54.00 54.00
-25.56 Peak
-26.58 Peak 92.56 114.00
---
---
---
74.00 74.00 74.00 94.00 54.00 54.00 54.00
-1.44 AVG
-28.46 Peak
-27.34 Peak
-26.29 Peak Remark:
frequency. 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown
--- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, N/A no emission measured remark, if no specific emissions from the EUT are with recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 27 Rev.00 Date of Issue: July 17, 2012 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 7.4 POWERLINE CONDUCTED EMISSIONS LIMIT According to 15.207(a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 H/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Frequency Range
(MHz) 0.15 to 0.50 Limits
(dBV) Quasi-peak 66 to 56*
0.50 to 5 5 to 30 56 60
* Decreases with the logarithm of the frequency. TEST CONFIGURATION Average 56 to 46*
46 50 See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. TEST PROCEDURE 1. The EUT was placed on a table, which is 0.8m above ground plane. 2. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 3. Repeat above procedures until all frequency measured were complete. This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 28 Rev.00 Date of Issue: July 17, 2012 Report No: T120628D02-RP1 FCC ID: P27SZDWS02 TEST RESULTS The initial step in collecting conducted data is a spectrum analyzer peak scan of the measurement range. Significant peaks are then marked as shown on the following data page, and these signals are then quasi-peaked. TEST DATA Not applicable (Since the EUT is powered by battery) This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Page 29 Rev.00
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2012-07-24 | 2405 ~ 2480 | DXX - Part 15 Low Power Communication Device Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2012-07-24
|
||||
1 | Applicant's complete, legal business name |
Sercomm Corporation
|
||||
1 | FCC Registration Number (FRN) |
0015548027
|
||||
1 | Physical Address |
8F, No. 3-1, YuanQu St, NanKang
|
||||
1 |
Taipei, N/A
|
|||||
1 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
T******@babt.com
|
||||
1 | TCB Scope |
A2: Low Power Transmitters (except Spread Spectrum) and radar detectors operating above 1 GHz
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
P27
|
||||
1 | Equipment Product Code |
SZDWS02
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
N****** W********
|
||||
1 | Title |
Engineer
|
||||
1 | Telephone Number |
886-2******** Extension:
|
||||
1 | Fax Number |
886-2********
|
||||
1 |
N******@SERCOMM.COM
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DXX - Part 15 Low Power Communication Device Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | ZigBee Door / Window Sensor | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Compliance Certification Services Inc.
|
||||
1 | Name |
K**** C******
|
||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
k******@ccsrf.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2405.00000000 | 2480.00000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC