FCC ID: XJ6-MT-202-2 2 CH 2.4 GHz FHSS RADIO CONTROL SYSTEM

MT-202 MT-202 Operating

MR-202 33mm(L)33mm(W)15mmH Antenna (Built in) Steering Dual Rate Lever (D/R) Steering Trim Lerer (CH1) 1 CONNECTION B 3 2 Connects to the steering servo Motor connector Battery connector Power switch 1 MT-202 1.CH1(Steering) Trim Steering neutral adjustments can be made by moving the steering trim lever to the left or right. When you install a servo, always check to be sure the servo is at its neutral position. Adjust the servo horn position and linkage so both are parallel. Be sure the steering trim on the transmitter is at the neutral position. 2.CH1(Steering Dual-Rate)D/R Use this function to adjust the steering travel of your model. If the model understeers while cornering, add steering by rotating the CW side of the D/R knob. When the model oversteers, take away steering by rotating the C.CW side of the D/R knob. 3.CH1(Steering)Reverse If the servo operate in the opposite direction,moving the reverse lever for the servo reversing. 4.Low Battery Indicator If the transmitter battery voltage drops below 4.2V the LED will be flashed. MR-202Receiver+ESC for 1/18 Car 1.CH1(Steering)OutputConnect the servo for steering operation. 2.Battery connector Connects to the battery.Red is plus,Black is minus. For Ni-cd battery 57cells(6.08.4V) or Lithium-Poly battery 2S(7.4V) 3.Motor connectorConnect to the motor. 4.CH2(Throttle) OperationForward reverse and brake are all linear. When switched to reverse operation just returning the throttle trigger from the brake position to the neutral position. 5.Low-battery&Heat protectionWhen the battery voltage drops below 5.5V or the FET are over heat,the motor will shut off and the LED will be rapid flash. MT-202&MR-202 Bind Binding Process 1.Turn the transmitter power on while pressing the bind sw. 2.The transmitter Red LED will flashing for 20 seconds. 3.Plug the battery into the MR-202, then turn on the power while the transmitter LED is flashing. 4.When the LED on the receiver unit is steady light ,binding is complete. 5.When the binding procedure is successful, the LED on the receiver will stay solid red when both the transmitter and receiver are turned on. TX LED Display LED ONPower on LED Rapid FlashBattery low LED Slow FlashBind mode RX LED Display LED OFFIndicates that the power is off or no signal reception LED ONReceiving signals LED Rapid FlashBattery low or heat protector is detected. 2 FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interferenceand (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirement . The device can be used in portable exposure condition without restriction The distance close to the finger usually should be 14mm. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

MERITRC Product name: 2CH 2.4GHZ FHSS RADIO CONTROL SYSTEM Model name: MT-202 D4 FCC ID: XJ6-MT-202-2 C a Vendor : SHANGHAI MERIT TECHNOLOGY CORP. Add: 1058 TAOGAN RD., SHESHAN TOWN, SONGJIANG DISTRICT, SHANGHAI, China

Company: SHANGHAI MERIT TECHNOLOGY CORP. Add: 1058 TAOGAN RD., SHESHAN TOWN, SONGJIANG DISTRICT, SHANGHAI, China Tel: (86) 21-57793858-218 Fax: (86) 21-57794269 FCC Authorization Date: 2020-09-29 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We, SHANGHAI MERIT TECHNOLOGY CORP., the undersigned, Hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature:

Typed or Printed Name: Dongcheng Zheng Title: Artificial Person

Company: SHANGHAI MERIT TECHNOLOGY CORP. Add: 1058 TAOGAN RD., SHESHAN TOWN, SONGJIANG DISTRICT, SHANGHAI, China Tel: (86) 21-57793858-218 Fax: (86) 21-57794269 E-mail: xyzhu@seahigh.com FCC Confidential Authorization Date: 2020-09-29 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: XJ6-MT-202-2 To: whom it may concern, In accordance with Sections 0.457 and 0.459 of the Commissions Rules, SHANGHAI MERIT TECHNOLOGY CORP. hereby requests long-term confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature:

Typed or Printed Name: Dongcheng Zheng Title: Artificial Person